Sentiotec MySentio WiFi User manual

EN
INSTALLATION AND OPERATING INSTRUCTIONS
English
Version 09/22 Ident no. 1-053-313
MySentio WiFi
1-053-313 / S-WIFI01

Table of Contents
1. About this instruction manual 3
2. Important information for your safety 3
2.1. Intended use 3
2.2. Safety information for the installer 4
2.3. Safety information for the user 4
3. Product description 5
3.1. Scope of delivery 5
3.2. Optional accessories 5
3.3. Product features 5
4. Installation and connection 6
4.1. MySentio WiFi installation 6
4.2. MySentio WiFi connection 7
4.3. Connection to home.com4 7
4.4. Connection to PRO B (B2, B3) and PRO C (C2, C3) 8
4.5. Connection to PRO D (D2, D2I, D3, D3I) 8
5. Commissioning 9
6. Overview of functions 11
7. Operation 12
7.1. Home menu 12
7.2. Settings 14
7.3. Device settings 15
7.4. Coloured light settings 16
7.5. Prole 18
8. Troubleshooting 19
8.1. Error messages 19
9. Maintenance 20
10. Disposal 20
11. Technical data 20

EN
Instructions for installation and use p. 3/20
1. About this instruction manual
Read these instructions for installation and use carefully and keep them within
reach of the device. This ensures that you can refer to information on safety and
operation at any time.
Symbols used for warning notices
In these instructions for installation and use, a warning notice located next to
an activity indicates that this activity poses a risk. Always observe the warning
notices. This prevents damage to property and injuries.
ATTENTION!
This keyword is a warning that damage to property can occur.
Other symbols
This symbol indicates tips and useful information.
These installation and operating instructions can also be found in
the downloads section of our website: www.sentiotec.com/downloads.
2. Important information for your safety
2.1. Intended use
Sentiotec WiFi is used to control the sauna remotely.
A sauna heater controlled by the remote start function of the sau-
na control unit must pass the combustion test as specified in
EN 60335-2-53 paragraph 19.101. If the heater does not meet
this requirement, an appropriate safety precaution must be used
(forexample:safetyswitch-o󰀨ordoormonitoring)
Any use exceeding this scope is considered improper use. Improper
use can result in damage to the product, severe injuries or death.

Instructions for installation and use p. 4/20
2.2. Safety information for the installer
●Installation and connection work on the devices may only be
carried out with the power supply disconnected.
●Observe the installation instructions for the sauna control unit
used.
●Also comply with the regulations applicable at the installation
location.
●For your own safety, consult your supplier in the event of prob-
lemsthatarenotexplainedinsu󰀩cientdetailintheinstallation
instructions.
2.3. Safety information for the user
●The WiFi must not be used by children under 8 years of age.
●The WiFi may only be used by children over 8 years of age, by
persons with limited psychological, sensory or mental capabilities
or by persons with a lack of experience/knowledge under the
following conditions:
– They are supervised.
– They have been shown how to use the device safely and
are aware of the hazards that could occur.
●Observe the operating instructions for the sauna control unit used.
●For your own safety, consult your supplier in the event of prob-
lemsthatarenotdescribedinsu󰀩cientdetailintheoperating
instructions.

EN
Instructions for installation and use p. 5/20
3. Product description
3.1. Scope of delivery
●MySentio WiFi
●1 pc. 1 m Ethernet cable, 8-pin RJ45
●Installation material
●Assembly instructions
3.2. Optional accessories
●Door sensor system (1-052-722 / SAB00102)
●Home door sensor (1-052-723 / SAB00103)
●Safety shutdown (SFE-xxxxx)
3.3. Product features
Sentiotec WiFi enables the functions of all existing sauna control units to be
operated using devices such as smartphones and tablets. This is done using
the MySentio app in a local network (WiFi), which is available free of charge for
Android (Google Play Store) and for iOS (App Store). The subscription is free of
charge for 3 years, after which fees may apply.
Compatible sauna control units:
●home.com4 RS485 (1-052-984 / HC4-B-RS485, 1-052-985 / HC4-W-RS485)
●Pro B2 (1-015-455 / PRO-B2)
●Pro B3 (1-015-457 / PRO-B3)
●Pro C2 (1-015-448 / PRO-C2)
●Pro C3 (1-015-451 / PRO-C3)
●Pro D (only in combination with BUS-CON-D / 1-053-348)
ATTENTION!
Standard-compliant operation
To ensure standard-compliant operation, safety devices must be installed in
accordance with the operating instructions for your sauna control unit.

Instructions for installation and use p. 6/20
ATTENTION!
Interference can impair signal transmission
●Route all data cables separately from other mains cables and control cables.
●Protect cables with only one layer of insulation by using a conduit (double
insulation).
ATTENTION!
Damage to the device!
Installation of the app and input of the settings (see “6. Overview of functions” and
“7. Operation”) must be completed before the sauna control unit is switched on.
30
27.5
4. Installation and connection
Work may only be carried out when the power has been disconnected.
During installation, observe the technical data on page 20.
1. Secure the WiFi module 1somewhere near the sauna control unit and within
the range of its network (WiFi) using the screws provided.
2. Sentiotec WiFi is connected to the sauna control unit using the 8-pin Ethernet
cable in accordance with the following diagrams:
3. Make a note of the serial numbers (10 digits) of your devices to ensure you
can enter them in the app later on.
Sauna heater................................................................................................
Sauna control unit ........................................................................................
Other products..............................................................................................
4.1. MySentio WiFi installation

EN
Instructions for installation and use p. 7/20
4.2. MySentio WiFi connection
MySentio WiFi
home.com4
PRO B-series
PRO C-series
PRO D-series
4.3. Connection to home.com4
RJ45
8-pin
RJ45
8-pin

Instructions for installation and use p. 8/20
4.4. Connection to PRO B (B2, B3) and PRO C (C2, C3)
MySentio WiFi
MySentio WiFi
BUS converter
RJ12
6-pin
RJ45
8-pin
4.5. Connection to PRO D (D2, D2I, D3, D3I)
RJ45
8-pin

EN
Instructions for installation and use p. 9/20
5. Commissioning
To activate remote start, refer to the operating instructions for the respective
control unit.
1. Download the “MySentio” app onto your smartphone or tablet
►Open the app and sign up.
►Following the instructions provided in the app.
2. Signing up (Fig. 1–3):
►Completealleldsandmakeanoteoftheemailandpasswordyouuse.
Fig. 1 Signing up/
logging in Fig. 2 Signing up Fig. 3 World of sensations
In case you have forgotten your password, simply enter the email address
you used when you registered. You will then be given instructions on how
to change the password.

Instructions for installation and use p. 10/20
3. Add a new device: (Fig. 4–5):
►Select your device and tap the switch below it. (Fig. 6)
►Connect the WiFi to the smartphone by pressing the pairing button.(Fig. 7)
► Renamethedeviceandwaituntiltheapphasnishedloading.(Fig.8)
►Enter the serial numbers of your devices. (Fig. 9)
Fig. 4 First steps Fig. 5 Conguration Fig. 6 Select device
Fig. 7 Pairing Fig. 8 Rename Fig. 9 Serial numbers

EN
Instructions for installation and use p. 11/20
6. Overview of functions
Sentiotec WiFi can only be used to control functions provided by the
sauna control unit in use (for example: Pro-series – NO coloured light,
control units for Finnish sauna mode – NO evaporator)
Sauna temperature Humidity Infrared (additional output) Light switchable Light dimmable Fan switchable Fan dimmable Preset time Operating time Coloured light User program
home.com4 RS485 XXXX X XXXX
PRO B2 X X X X
PRO B3 X X X X X
PRO C2 X XXXXXXX X
PRO C3 XXXXXXXXX X
PRO D2 X XXXXXX X
PRO D2i X XXXXXXX X
PRO D3 XX XXXXXX X
PRO D3i XXXXXXXXX X

Instructions for installation and use p. 12/20
8
Fig. 10 Home menu
7. Operation
2
3
7.1. Home menu
c
7
9
1
a
b
6
4
5
f
e
d

EN
Instructions for installation and use p. 13/20
DANGER!
Makesurethatnoammableobjectsareeverleftonthesaunaheater
when the sauna cabin is put into operation.
1Devices – switch between devices or add new devices.
2Settings – see page 14
3Status–statusdisplay(standby,on,o󰀨)
4Temperature – setting for the preferred temperature (set point)
Increase/decrease temperature using arrow up/down or
bymovingtheameinthecircle
5Temperature display – shows the selected temperature (set point) when
entering the settings, changes to displaying the measured temperature
(actual value) after 3 sec.
6 Humidity–combimodeon/o󰀨–canonlybeswitchedonifthesauna
heater is switched on (see b)
7 Intensity of humidity –setting for the preferred humidity (set point)
The maximum humidity set point will depend on the sauna temperature.
The higher the sauna temperature, the lower the maximum humidity value
that can be set (see the operating instructions for the sauna control unit in use)
8 Infrared –infraredlampon/o󰀨
9Intensity of infrared – IR lamp dimmer levels 1–7
aHeater–heateron/o󰀨
bLight–cabinlighton/o󰀨,ifdimmablepressandholdtoenterdevice
settings – see page 15
bFan–fanon/o󰀨,ifvariablepressandholdtoenterdevicesettings
– see page 15
dColoured light–colouredlighton/o󰀨,pressandholdtoenterdevice
settings – see page 15
eDevices – back to the Home menu
fProle – see page
Sentiotec WiFi can only be used to control functions provided by the
sauna control unit in use (for example: Pro-series – NO coloured light,
control units for Finnish sauna operation – NO evaporator) – see page 11
Press and hold: press the symbol and hold it for 3 seconds

Instructions for installation and use p. 14/20
Fig. 11 Settings
1
2
4
5
1Device settings – see page 15
2Colour light settings
– see page 16
3All o󰀨–switcheso󰀨allfunc-
tions and consumers at once.
4 User program on/o󰀨 – there are
5 preset user programs available,
which can be changed.
5 Edit user program –the set-
tings in the user programs can
be changed. The settings for
the following functions can be
changed to suit the user’s pref-
erences.
►Temperature
►Humidity
►Infrared
►Light
►Fan
►Coloured light
7.2. Settings
3

EN
Instructions for installation and use p. 15/20
Fig. 12 Device settings
1
2
3
4
5
6
7
8
7.3. Device settings
9
a
b
1Lighting with heater – switches
on the lighting when the sauna
heater is switched on
2Cabin light intensity – cabin
light dimming levels (0–100%)
3Fan intensity – variable fan
output levels (0–100%)
4 Switch-on time – setting for
the maximum period for which
the sauna should operate
continuously.
5 Relay box mode – Only avail-
able with sentiotec WiFi Exten-
sion Box (1-053-315).
6Time zone – selection of the rel-
evant time zone
7 Recongure WLAN–congure
WLANconnectionoftheWi
module
8 Firmware updates – suggests
new app versions.
9 Info – query information,
such as: software version,
device type, etc.
a Rename – rename the device
in the app.
bRemove – remove the device
from the app.

Instructions for installation and use p. 16/20
Fig. 13 Coloured light settings
7.4. Coloured light settings
1
3
1Light group on/o󰀨 – tap to
switchon/o󰀨
2Rename light group – tap to
rename
3Light group settings –tap to
open, then select from colour
and intensity, and tap again to
close
4Colour – colour setting for
the light group that is open is
displayed – press and hold to
select colours – setting for the
preferred colour entered using
the colour wheel or an individual
colour, or colour rotation
5 Intensity – coloured light dim-
ming levels for the light group
that is open (0–100%)
4
2
5

EN
Instructions for installation and use p. 17/20
1
3
2
4
5
6
7
1 Standard – select from standard colours and colour rotation
2Colour ring – individual colour selection
3Colours – tap to select the desired colour
4 Colour ring – individually selectable colours
5 Colour eld – set the white-bordered circle to the desired colour
6 Cancel – closes the colour selection and changes are not applied
7 OK – to apply the selected colour
Fig. 14 Standard colours Fig. 15 Colour ring

Instructions for installation and use p. 18/20
1Prole – you can change
the following information:
►First name
►Last name
►Email address
► Removeprole
2Language – select language
3 GTC – general terms and con-
ditions
4 Privacy policy –data protection
guidelines
5Licence agreement – end user
licence agreement
6
Licences – open source licences
7 Logout–logoutofyourprole
8 Version – current version of
the app
Fig. 16 Prole
1
2
3
4
5
6
7.5. Prole
7
8
Fig. 17 Prole

EN
Instructions for installation and use p. 19/20
8. Troubleshooting
8.1. Error messages
The following table describes the possible faults and their causes. Further infor-
mation and assistance can be found in the sentiotec help centre at:
sentiotec.zendesk.com/hc/de
Description Cause/remedy
Cannot connect Make sure that the WiFi network to be
connectedissu󰀩cientlystrong.
WiFi connection is interrupted
during setup
The name of the WiFi network
contains inadmissible characters.
Cannot connect
or
WiFi connection terminates
during setup
The WiFi module requires access to
port 8883 (secure MQTT), which must
beopenedintherewall.Additional-
ly, there must be access for Network
Time Protocol (NTP) servers. Also
check that other ports are not blocked,
especially 443, 8443 and 8883.
WiFi is not connected
after power failure
Switch the power supply of the sauna
controlunito󰀨andonagain,check
the LED on the WiFi module.
Control LED of the WiFi dongle
does not light up
Check whether power is reaching
the WiFi dongle via the socket on
the sauna control unit.
Control LED of the WiFi dongle
lights up, but still no function
Check that software version of
your controller is compatible.
Error codes: e.g.: 7,2,1 (=A,B,C)
A: WiFi status
B: WiFi connection status
C: AWS connection status
7: WiFi status – AP_RUNNING
2: WiFi connection status – the phone
is not maintaining a connection to
the WiFi module.
1: AWS connection status – AWS con-
nection interrupted, check the internet
and ports of the router.
Also note the error messages of your sauna control unit.

Instructions for installation and use p. 20/20
●Dispose of packaging materials in accordance with the applicable
waste disposal regulations.
●Used devices contain reusable materials as well as hazardous
substances. Therefore, do not dispose of your used device with
household waste, but do so in accordance with the locally appli-
cable regulations.
9. Maintenance
The device is maintenance-free. An internet connection is used to update it
automatically.
10. Disposal
11. Technical data
Ambient conditions
Ambient temperature: -20 °C to +40 °C
Protection class (protected against splashing water): IP 20
Minimum requirement WiFi 2.4 GHz: 1 Mbit
Control unit
Dimensions: 83 x 56 x 24.5 mm
Operating voltage: 24 V DC max. 10 W
Connection cables
Power supplied by Ethernet cable: 8-pin RJ45 max. 3 m