Serta ComfortLift User manual

POWER LIFT CHAIRS

CONTENTS Serta Perfect Lift Chair/Serta ComfortLift
2
I. INTRODUCTION................................................................................................................................ 4
II.SAFETY................................................................................................................................ 5
III.YOUR SERTA PERFECT LIFT CHAIR............................................................................... 8
IV. ASSEMBLY/DISASSEMBLY................................................................................................ 10
V. OPERATION.........................................................................................................................12
VI. BASIC TROUBLESHOOTING.............................................................................................. 14
VII.CARE AND MAINTENANCE................................................................................................ 15

Serta Perfect Lift Chair/Serta ComfortLift INTRODUCTION
3
SAFETY NOTICE
All Serta Lift Chairs provide for state-of-the-art features and components to provide safety, ultimate
comfort and longevity with proper care. Before using your new Serta Perfect Lift Chair or Serta
ComfortLift Chair for the first time, it is important to know and understand all information contained
in this manual. If there are any parts that are not understood, please call your authorized Serta Per-
fect Lift Chair, or Serta ComfortLift Chair Dealer. Failure to follow warnings, instructions and notes
in this manual can result in personal injury, or product damage voiding the product warranty.
PURCHASER'S AGREEMENT
Upon acceptance of delivery of this product, you promise that you will not change, alter, or modify this
product or remove or render inoperable or unsafe any guards, shields, or other safety features of this
product; fail, refuse, or neglect to install any retrofit kits from time to time provided to enhance or
preserve the safe use of this product.
SHIPPING AND DELIVERY
Before using your lift chair for the first time, please be sure your delivery is complete as some compo-
nents may be individually packaged. If you do not receive a complete delivery, please contact your
authorized provider or dealer immediately. Where damage has occurred during transport, either to
the packaging or content, please contact the delivery company responsible.
MOTOR VEHICLE TRANSPORT
Use precautions to properly secure your product If you will be transporting your lift chair in a motor
vehicle, individual components should be secured against slipping. The lift chair itself must also be
secured against slipping (a possible hazard during vehicle braking).

SAFETY GUIDELINES Serta Perfect Lift Chair/Serta ComfortLift
4
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated
procedures can cause either personal injury, component damage, or malfunction. On the
product, this icon is represented as a black symbol on a yellow triangle with a black border.
MANDATORY! These actions should be performed as specified. Failure to perform mandatory
actions can cause personal injury and/or equipment damage. On the product, this icon is
represented as a white symbol on a blue dot with a white border.
PROHIBITED! These actions are prohibited. These actions should not be performed at any
time or in any circumstances. Performing a prohibited action can cause personal injury
and/or equipment damage. On the product, this icon is represented as a black symbol with
a red circle and red slash.
Please fill out the following and save for future reference:
Copyright © GES, LLC
NOVO Home, Inc. 2015
Serta Perfect Lift/Serta ComfortLift Provider/Dealer: __________________________________
Address: _____________________________________________________________________
Telephone: ____________________________________________________________________
Purchase Date: __________________________________________________________________
Please take a minute to review the important safety symbols below that will appear throughout this manual.
Read and understand completely for safe operation of your new Serta Perfect Lift, or Serta ComfortLift Chair.
NOTE: This owner's manual contains the most current specifications and product information available at the time
of publication. NOVO Home reserves the right to update this document as necessary. There is a possibility that the
changes may reflect slight variations from the illustrations and explanations from the product you have purchased.
The most current version of this, manual can always be found at www.NovoHome.net for your convenience.

Serta Perfect Lift Chair/Serta Comfort Lift SAFETY GUIDELINES
5
Pinch/Crush Points Hazard! Do not place objects or appendages in the path of moving
parts.
Read and follow the information in the owner’s manual.
Maximum allowable weight capacity
Do not connect an extension cord to the AC/DC converter or the battery charger.
Electrical Hazard!!!
Removal of grounding prong can create electrical hazard. If necessary, properly install
an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access.
This product has been tested and complies to IEC 60601-1-2.
Do not place objects under the footrest when lift chair is in fully reclined position. Make
sure area is clear of obstructions, including pets and small children, during operation.
Do not cover or place the external transformer under the chair. Keep in an open, well-
ventilated area free from foreign material and away from possible pinch points.
Do not place objects under lift chair. Make sure area is clear of obstructions, including
pets and small children, during operation.
Class II Equipment
Indoor Use Only. Avoid exposure to rain, snow, ice, salt, or standing water. Maintain and
store in a clean and dry environment.
9V Battery door location.
SERTA PERFECT LIFT CHAIR/SERTA COMFORT LIFTCHAIR SAFETY SYMBOLS
The symbols below represent labels used on the Serta Perfect Lift Chair and Serta ComfortLift to identify
warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand
these symbols completely. Do not remove these labels from your product. Please note that not all of the
symbols may be used on your lift chair model.

SAFETY GUIDELINES Serta Perfect Lift Chair/Serta ComfortLift
6
Degree of protection against electric shock.
Properly dispose of all electronic components, including the external transformer, hand control,
batteries, actuator motors, and wiring. Contact your authorized Serta Perfect Lift Chair dealer or
provider for more information.
Green LED on transformer indicates power to the unit is on.
MANDATORY! Read andfollow the information provided in this owner’s manual
before attempting to operate your Serta Perfect Lift Chair or ComfortLift for the
first time.
MANDATORY! Stay within the specified weight capacity of your lift chair. Your
provider will not be held responsible for injuries and/or product damage resulting
from failure to observe weight limitations.
Please recognize there will be certain situations, including some medical conditions, that will require
practice operating the lift chair in the presence of a trained attendant. A trained attendant may be a
family member or health care professional specially trained in assisting you with performing various
daily living activities while safely operating a Serta Lift chair.
Below are some precautions, tips, and other safety considerations that will help you become familiar
with operating the lift chair safely.
MODIFICATIONS
DO NOT not modify, add, remove, or disable any feature, part, or function of your Serta lift chair. Unau-
thorized modifications may lead to personal injury and/or product damage and may also void your
product’s warranty.
NOTE: Use genuine factory replacements parts only for all repairs and replacements. Genuine
Serta Perfect Lift Chair and Serta ComfortLift parts can be obtained from your authorized Serta
dealer / provider, or by calling (214-407-8645)
WEIGHT LIMITATIONS
Your lift chair is rated for a maximum weight capacity. Please refer to the specifications table for this
limit.

Serta Perfect Lift Chair/Serta ComfortLift SAFETY GUIDELINES
7
Degree of protection against electric shock.
Green LED on transformer indicates power to the unit is on. Not applicable to all models.
Properly dispose of all electronic components, including the external transformer, hand control,
batteries, actuator motors, and wiring. Contact your authorized Serta Perfect Lift Chair dealer or
provider for more information.
MANDATORY! Read and follow the information provided in this owner’s manual
before attempting to operate your Serta Perfect Lift Chair or ComfortLift for the
first time.
MANDATORY! Stay within the specified weight capacity of your lift chair. Your
provider will not be held responsible for injuries and/or product damage resulting
from failure to observe weight limitations.
Please recognize there will be certain situations, including some medical conditions, that will require
practice operating the lift chair in the presence of a trained attendant. A trained attendant may be a
family member or healthcare professional specially trained in assisting you with performing various
daily living activities while safely operating a Serta Lift chair.
Below are some precautions, tips, and other safety considerations that will help you become familiar
with operating the lift chair safely.
MODIFICATIONS
DO NOT not modify, add, remove, or disable any feature, part, or function of your Serta lift chair.
Unauthorized modifications may lead to personal injury and/or product damage and may also void
your product’s warranty.
NOTE: Use genuine factory replacements parts only for all repairs and replacements. Genuine
Serta Perfect Lift Chair and Serta ComfortLift parts can be obtained from your authorized
Serta dealer / provider, or by calling (214-407-8645)
WEIGHT LIMITATIONS
Your lift chair is rated for a maximum weight capacity. Please refer to the specifications table for
this limit.
NOTE: If unintended motion occurs, discontinue use of the lift chair. Contact your authorized
provider to report the incident.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular
phones,mobile two-way radios (such as walkie-talkies), radio stations, TV stations, amateur radio
(HAM) transmitters, wireless computer links, microwave signals, paging transmitters, and medium-
range mobile transceivers used by emergency vehicles. In some cases, these waves can cause unin-
tended movement or damage to the control system of electrically-powered devices. The Serta lift chair
user can help prevent electromagnetic interference by maintaining a minimum distance between
portable and mobile RF communications equipment. It is recommended that at least 9 feet (3 meters)
of distance be maintained between the lift chair and any handheld equipment emitting 10 W or more
of output power. Refer to the manufacturer’s literature for the handheld device to determine the maxi-
mum output of that device.
Every electrically-powered device has an immunity (or resistance) to EMI. The higher the immunity
level, the greater the protection against EMI. Per EMC standards, this product has passed immunity
testing and is rated as a Group 1, Class B product, meaning the lift chair uses RF energy only for its
internal function. Therefore, its RF emissions are very low and are not likely to cause any interference
in nearby electronic equipment, making the lift chair suitable for use in all establishments, including
domestic establishments and hospitals.
• Class II equipment/Type B protection against electric shock
• Degree of protection against the ingress of solid/liquids—IPX0
• Mode of operation—Maximum Duty Cycle: 2 min. ON/18 min. OFF
Storage and Operation
•Temperatures Transportation or storage: -104°F/-75°C to 158°F/70°C
•Operation: 50°F/10°C to 104°F/40°C
Electromagnetic and Radio Frequency Interference (EMI/RFI)
The scissor and lift mechanisms are labeled to show pinch/crush point hazards on your Serta lift chair.
Keep clear of these areas and make sure the path of motion is unobstructed. See figure 3.1 for
pinch/crush point locations.
WARNING! Do not place objects or appendages in the path of ANY moving parts.
Degree of Protection/Mode of Operation
WARNING! Laboratory tests have shown that electromagnetic and radio frequency
waves can have an adverse effect on the performance of electrically-powered
devices, such as lift chairs.
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of
radio transmitters may cause unintended movement of your electrically-powered
device due to EMI. Exercise caution when using any of these items while operating
your Serta Perfect Lift/ComfortLift lift chair.
WARNING! The addition of accessories or components to the lift chair can increase
the susceptibility of the chair to EMI. Do not modify your lift chair in any way not
authorized by your provider.
WARNING! Your lift chair itself can disturb the performance of other electrical
devices located nearby, such as alarm systems.

ABOUT YOUR LIFT CHAIR Serta Perfect Lift Chair/Serta ComfortLift
8
Figure 3.1 Lift Chair Main Components
HAND CONTROL: Contains the
controls needed to operate the
various functions of the lift chair.
Refer to the Hand Control Quick
Reference Guide for more informa-
tion on hand control options.
EXTERNAL TRANSFORMER, POWER CORD:
Connects to a standard electrical outlet to provide
power to the lift chair; may be equipped with an
LED which will show green to indicate power to
the transformer. Refer to the optional wall
mounting diagram.
SCISSOR MECHANISMS (PINCH POINT):
Extend or retract to take the chair through the
various stages of recline. See pinch point warning
for more information.
QUICK-RELEASE CONNECTOR:
Enables the user to detach the hand
control from the lift chair.
BODY COMPONENTS
Lift chairs are equipped with several frame and electrical components. Typically, frame (or body) compo-
nents include a removable back pad*, removable chaise pad*, footrest, leg levelers, a lift mechanism,
and scissor mechanisms. The electrical components include the external transformer, hand control,
and batteries(not included). Refer to figure 3.1 and note that the illustrations and options listed may not
reflect the type of lift chair that you own.
BATTERIES (NOT INCLUDED):
Provide the power needed to return
the lift chair to an upright or semi-
upright position in the event of a
power failure. Must be installed in
the external transformer if equipped
with battery backup.
LIFT MECHANISM (PINCH
POINT):Responds to the
hand control commands to
position the chair in the sit
and stand positions. See
pinch point warning for more
information.
LEG LEVELERS (4):
Manually rotate up or down to
stabilize the chair before use.

Serta Perfect Lift Chair/Serta ComfortLift YOUR LIFT CHAIR
9
WARNING! Keep all electrical components free from moisture at all times to
prevent shock and/or electrical hazard.
ELECTRICAL COMPONENTS
Your lift chair is equipped with a low voltage DC electrical system that reduces the standard household
alternating current of 100V AC - 240V AC to direct current (24/39V DC). The electrical components
include the external transformer, batteries (not included), and hand control. Keep these areas free from
moisture at all times.
BATTERIES:
Provide the power needed to return the lift chair to an upright or semi-upright position in the event of
a power failure. The batteries (not included) must be installed into the external transformer. See IV.
“Assembly/Disassembly.”
WARNING! Pinch/Crush Points Hazard! Be aware that the lift mechanism and
scissor mechanisms are a pinch point on the lift chair. Keep the following
items and similar objects clear of these points when operating the lift chair:
• appendages
• small children
• pets
• wires
• oxygen tubes
• loose items, including but not limited to clothing and blankets
• electrical power cords

ASSEMBLY/DISASSEMBLY Serta Perfect Lift Chair/Serta ComfortLift
10
Figure S.2 Chair Assembly
CORRECT
INCORRECT
Your lift chair will require some light assembly before initial use. It may also require disassembly to make
servicing the chair more convenient.
LIFT CHAIR SETUP
All Serta lift chair models are shipped with the backs off unless setup by your dealer or provider. Please
see instructions below diagram.
1. Check that the locking clip on the back of the chair is in the vertical position. Reposition if necessary.
2. Position the hand control and cable over the chair base, then slide the back onto the base. (KD clips may
be located on either side of the lift chair.)
NOTE: Depending on chair width, it may be necessary to slide on one side of the back at a time. If this is
the case, level the chair-back before pressing down to lock into position.
3. Push firmly on the top of the back to lock into position. You must hear a click from each side of the chair
to ensure the back is locked in properly.NOTE: Pull up on the chair-back to ensure that it is locked in place.
NOTE: Pull up on the chair-back to ensure that it is locked in place.

Serta Perfect Lift Chair/Serta ComfortLift ASSEMBLY/DISASSEMBLY
11
EXTERNAL TRANSFORMER
(TOP AND BOTTOM VIEW)
BATTERY
DOOR
POWER
CORD
1. Unplug the external transformer power cord
from the electrical outlet.
2. Open the marked battery door on the external
transformer.
3. Install two 9V Alkaline batteries into the external
transformer (Fig. S.3).
4. Replace the battery door.
NOTE: Always make sure the external transformer
is equipped with two fresh 9V batteries, since the
battery backup system does not recharge itself.
Fresh batteries are defined as 9V alkaline batteries
that are replaced every time the battery backup
system is activated during apower failure, or once a
year if the battery backup system has not been
activated.
NOTE: If the lift chair is not in use for an extended
period of time , remove the batteries from the
external transformer. The lift chair will draw
power from the batteries even when it is not in
use.
BACKUP BATTERY INSTALLATION
Your Serta Perfect Lift Chair/Serta ComforLift lift chair comes equipped with a battery backup system that
will activate during a power failure. The backup system is powered by two 9V batteries (not included) that
need to be installed into the external transformer. Follow these steps to install the batteries:
PLACEMENT OF YOUR SERTA PERFECT Figure S.3 Lift Chair Battery Backup Location
LIFT CHAIR / SERTA COMFORTLIFT CHAIR
Placement of your lift chair should be near a convenient electrical outlet and on a level surface. (NEVER USE
EXTENSION CORDS UNLESS CONNECTED TO A UL COMPLIANT POWER BAR WITH AUTOMATIC
CIRCUIT BREAKERS)
Lift chairs are heavy. We recommend that at least two people position your chair in order to avoid injury when lifting. Follow these
steps to locate your chair in a safe manner:
1. Place the back of the chair approximately 30 inches (76 cm) from the nearest obstruction or wall with the chair in
the seated position. This distance is approximate and may vary by model number.
2. Adjust the leg levers if necessary as shown in figure S.2
3. Install (2) AA Alkaline Batteries into the transformer battery compartment. (Batteries not included)
4. Place the external transformer on the floor clear of any potential obstructions in an open, well ventilated area. The unit
may also be wall-mounted. (See figure S.XXX)
5. Position the low voltage connection cable in a manner that it will not be pinched when the chair is in motion.
6. Connect the low-voltage cable to the external cable. The fittings are unique to avoid making any incorrect connections
7. Plug the cord from the external transformer directly into a nearby electrical outlet NOT USE AN EXTENSION CORD!
NOTE: If there are any problems discovered during this process, STOP IMMEDIATELY and contact your
authorized Serta Perfect Lift Chair/Serta ComfortLift dealer/provider. To avoid personal injury, or product
damage, do not plug the unit into an electrical outlet until the problem is resolved. Electrical problems should
only be addressed by qualified service technicians.

OPERATIONS Serta Perfect Lift Chair/Serta ComfortLift
12
OPERATION PRECAUTIONS
Please use the following precautions during the operation of your lift chair. Read and follow these precautions
carefully in order to ensure safe lift chair operation and to prevent injury and/or product damage.
• Plug the power cord directly into a nearby electrical outlet. NEVER use an extension cord!
•Do not place anything on top of or near the external transformer, especially anything containing beverages.
• When the external transformer box or hand control requires cleaning, unplug the power cord from the
electrical outlet and use a clean, dry cloth or lightly dampened cloth. Allow time to become completely
dry before plugging the power cord back into the electrical outlet.
• Periodically check the hand control and all power cords for visible damage. Keep the hand control and
transformer away from all heated surfaces.
• Ensure the hand control is out of the way before sitting in the chair.
• Keep children and pets away from all moving parts when operating the lift chair.
•Do not allow children to play on or operate the lift chair. Only the intended user should operate the lift chair.
• Keep the hand control locked or utilize the quick-disconnect feature on the standard hand control when
the Serta lift chair is not in use to prevent unintended operation of the chair.
• Avoid pinch points, such as the lift and scissor mechanisms. Keep hands and feet clear of these areas.
Always leave the lift chair in an upright and closed position when not in use.
• NEVER sit or stand on the footrest.
•NEVER “drop” into the lift chair when sitting if it is in a partially raised position. This can result in permanent
damage to the chair.
HAND CONTROL OPERATION
The Hand Control that comes with every Serta Perfect Lift Chair and every Serta ComfortLift Chair
is designed for simplicity, convenience and long life. Please refer to the Hand Control Guide for
additional information.
PROHIBITED! Do not place objects under the lift chair. Make sure area is clear of
obstructions, including pets and small children, while in operation.
WARNING! Prevent the risk of electrical shock, fire, falls, and/or being pinched. Follow all
instructions and precautions provided.
WARNING! Prevent potential equipment damage! Do not place the external transformer
under the lift chair.
WARNING! Do not cover the external transformer. Keep the transformer in an open,
well-ventilated area free from foreign material/debris to ensure proper operation.
WARNING! NEVER lean on or apply downward force to the chair-back when the lift chair
is in the fully reclined position. Doing so may cause the lift chair to tip, resulting in
personal injury and/or product damage.
WARNING! NEVER use the footrest as a seat, or for purposes outside its intended use.
Doing so could cause instability in the lift chair and place undue stress on lift chair
components, resulting in personal injury and/or product damage.
WARNING! Be sure to lock or disconnect the hand control when the lift chair is not in use.

Serta Perfect Lift Chair/Serta ComfortLift OPERATIONS
13
Follow these simple steps to properly sit in your chair:
1. Make sure that the Serta Perfect Lift Chair/Serta ComfortLift Chair is in the standing position.
2. Back into the chair and sit in the center of the seat.
3. Press the DOWN button (switch) to lower the lift chair to a comfortable seated position.
Follow these simple steps to operate your lift chair from the seated position:
1. Press the UPbutton (switch) toraise your lift chair tothe standing position.
2. Press the DOWN button (switch) tolower the lift chair toa seated position.
Follow these simple steps to recline your lift chair from the seated position:
1. Press and hold the DOWN button (switch) until reclined.
2. Press and hold the UP button (switch) to return to an upright, seated position. Release the
button(switch) when the chair reaches a comfortable seated position.
Follow these simple steps to properly stand up from your chair:
1. Press and hold the UP button (switch) to raise your lift chair.
2. Release the button (switch) when the chair reaches a height where you can stand up.
Two Motor Infinite Position Chairs
Certain Serta Perfect Lift Chairs and Serta ComfortLift Chairs come equipped with two
motors. This feature allows for the Backs and the Footrest to operate independently of
one another.
To operate, please refer to the diagram of the 4-Button Hand Control on Page 18.
There is a corresponding Icon / Picture that corresponds with the function of a specific
button.
Serta Infinite Position Chairs provide an added measure of comfort that is tailored to
the individual user's comfort preferences.

TROUBLESHOOTING AND FAQ Serta Perfect Lift Chair/Serta ComfortLift
14
On occasion, your lift chair may require troubleshooting. The following troubleshooting tips and FAQs
should summarize what you need to know about your lift chair. If at any time you do not feel comfortable
performing the troubleshooting steps listed in this manual, contact your authorized provider or Serta
Perfect Lift Chair/ComfortLift dealer for service. Please have the model number, serial number, and
nature of the problem when calling.
FREQUENTLY ASKED QUESTIONS
What if my chair does not operate at all?
• Make sure the external transformer is plugged into a properly wired electrical outlet.
• Check the circuit breaker box connected to the electrical outlet to ensure the outlet is receiving power.
• Ensure the low voltage connection cable is plugged into the external transformer.
• Ensure that all cables are connected properly.
What if my lift chair operates in one direction only?
• Check the up and down buttons or toggle switch on the hand control to make sure they do not stick. If
the buttons or switch are sticking in either position, the hand control may need to be replaced or cleaned.
Disconnect the hand set and clean with a damp cloth. Allow to complety dry before reconnecting..
• Contact your authorized provider or dealer for further assistance.
What if my lift chair stops during a lifting cycle?
•Your lift chair is equipped with an internal thermal safety shutoff switch located inside the external
transformer that prevents the motor control box from overheating. If the thermal shutoff activates, allow
the lift chair to remain in a stationary position for 10 minutes to allow the motor to cool, then resume
normal operation. If you notice the motor/motors overheating frequently, contact your authorized
provider as soon as possible.
• There may have been a power failure and/or there are no batteries in the external transformer or the
batteries have no charge. Always make sure there are fresh 9V Alkaline batteries in the external
transformer if equipped with battery backup.
• Check the circuit breaker box connected to the electrical outlet to ensure the outlet is receiving power.
What if my chair is rocking from corner to corner after I position the chair?
The floor may be uneven or the carpet may be affecting chair position. A simple adjustment at the leg
levelers in the area where the chair is rocking will stabalize the chair. See Ill. "Your Lift Chair" for instruc-
tions on leveling your chair.
Where can I place the external transformer box?
•On the floor away from heat sources in an open, well-ventilated area where there will not be any
obstructions.
• On the wall away from heat sources utilizing the optional external transformer wall mount. Refer to the
Wall Mount Diagram Product Insert provided with your lift chair.
Where do I find the Serial Number on my lift chair?
You can find the serial number in two locations-one is near the rear of the motor on the steel
mechanism, the second is attached to the side of the back frame. The model number for your lift chair
is printed below the serial number bar code.
Who do I call for service?
Contact your authorized provider or dealer for service, or NOVO Home [phone]

Serta Perfect Lift Chair/Serta ComfortLift CARE AND MAINTENANCE
15
Your Serta Perfect Lift/Serta ComfortLift chair will require routine maintenance checks. You can perform
many of these checks, but others may require assistance from your authorized provider or dealer. Your
new Serta Perfect Lift Chair / Serta ComfortLift will provide you with years of trouble free service by simply
following a few easy steps in this guide.
FABRIC CARE
Visually inspect your fabric on a regular basis to look for any pulls or tears. All Serta Lift Chairs are covered
with high quality nationally recognized fabric producers. Check with your authorized provider or dealer for
the correct cleaning code and follow all instructions. Avoid leaving your chair in direct sunlight for
prolonged periods of time.
WARNING! Never allow fabric to come in direct contact with any type of heat source
(e.g., a space heater or cigarette). Personal injury or fire damage may occur.
WARNING! Your provider strongly recommends that you do not smoke cigarettes
while seated in or using your lift chair, although the lift chair has passed the
necessary testing requirements for cigarette smoking. You must adhere to the
following safety guidelines if you decide to smoke cigarettes while seated in or
using your lift chair.
• NEVER leave lit cigarettes unattended.
• Keep ashtrays a safe distance from the lift chair.
• Always make sure cigarettes are completely extinguished before disposal.
NOTE: Do not use solvent-type cleaners to spot clean. Do not saturate the fabric. Prevent damage to the
fabric; do not expose the lift chair to direct sunlight.
ELECTRONICS CARE
• Regularly inspect all wiring harnesses to make sure they are not damaged or frayed.
• If damage is present, unplug the lift chair and contact your authorized provider at once.
• Keep all electronics free from moisture and temperature extremes. Warranty is limited to indoor
residential use.
WARNING! Even though the lift chair has passed the necessary testing requirements
or ingress of liquids, you should keep electrical connections away from sources of
dampness, including direct exposure to water or bodily fluids and incontinence.
Check electrical components frequently for signs of corrosion and replace as necessary.
DISPOSAL AND RECYCLING
Your lift chair must be disposed of according to applicable local and national statutory regulations. Con-
tact your local waste disposal agency or authorized provider/dealer for information on proper disposal of
lift chair packaging, metal frame components, fabric, electronic components, and batteries.
WARNING! Plastic bags are a suffocation hazard. Dispose of plastic bags properly
and do not allow children to play with them.

HAND CONTROL REFERENCE GUIDE Serta Perfect Lift Chair/Serta ComfortLift
16
USB
UP
BUTTON
Press and hold to
raise lift chair to
seated or standing
position.
DOWN
BUTTON
Press and hold to
lower lift chair to
seated or reclined
position.
BOTÓN
ARRIBA
Pulse y mantenga pulsado
para elevar el sillón a la
posición de sentado
o de pie.
BOTÓN ABAJO
Pulse y mantenga pulsado
para bajar el sillón a la
posición de sentado
o reclinado.
BOUTON
VERS LE HAUT
Appuyer et maintenir pour
élever le fauteuil auto-
souleveur àla position
assise ou debout.
BOUTON
VERS LE BAS
Appuyer et maintenir pour
abaisser le fauteuil auto-
souleveur àla position
assise ou inclinée.
Two Button Hand Controls Operate all 3-Position Serta Perfect Lift / ComfortLift Chairs
(Model Numbers 320, 860, 870, 882, 893, 900 and 920)

Serta Perfect Lift Chair/Serta ComfortLift TRANSFORMER DIAGRAM
17
D
CPow
er
9V 6LR61
thgiLrewoP
It requires
(2) 9V Alkaline
Batteries
(Batteries Not Included)

Four-Button Hand Controls Operate all Infinite Position Serta Perfect Lift / ComfortLift Chairs
(Model Numbers 592 and 872)

Your Serta Perfect Lift Chair or
Serta ComfortLift Chair has undergone
an extensive inspection procedure to
ensure your total satisfaction.
Tailoring & Workmanship
Appearance & Comfort
Performance Tested
Date inspected
Inspector
Product Serial #
Copyright © GES, LLC
NOVO Home May 2015