Copeland Furniture Keaton Queen User manual

Instructions for Keaton Beds
Tools required
Components included:
Upholstered headboard (1)
Allen wrench (provided)
Step 1: Attach the Base Assemblies to the Siderails
Align the holes on each end of the
Base Plate with the holes on siderail
cleats (Figure 1). Insert the 2”
(50mm) hex bolts from the top of the
cleats and tighten with the provided
Allen wrench. Make sure the tip of
the leg is facing out.
Hardware included:
¼ - 20 x 50mm hex bolts (8)
1
Figure 1.
Install the Base Assembly to the Siderails
¼ - 20 x 50mm
hex bolt
Allen wrench (1) Upholstered footboard (1)
Base assembly (2)
Platform hardware (1) Siderail L (1)
Siderail hardware (1)
Platform kit (1)
Siderail R (1)
6” support block (1)
Base
Assembly
NOTICE: Beds must be disassembled before moving to avoid damage. Never attempt to
move the bed while it is assembled. Failure to do so would void the warranty.
Base Plate
Siderail Cleat
Base Plate
Keaton Upholstered Bed
Cal King
King 78 1/2” x 88” x 49 3/4”
Queen 62 1/2” x 88” x 49 3/4”
74 1/2” x 92” x 49 3/4”
Please
identify the
listed items
before
installation.
Siderail
Siderail cleat
Leg
facing out

Tools required
Step 2:
Allen wrench
Assemble siderails,
2
SIDERAIL
headboard, and footboard
Screw the threaded stud into the
insert in the headboard leg until it
stops.
Slide the rail into mating holes for
dowels on the headboard side.Slide the curved washer and
the nut in place as shown, and
tighten the nut with the wrench
provided in the side rail
hardware kit.
Figure 2.
Wrench (in the siderail hardware kit)
SIDERAIL L
Use the following steps to attach the headboard and footboard to the
BASE ASSEMBLY
Curved washer
HEADBOARD
siderails (Figure 2)
FOOTBOARD
Curved washer
Nut
Stud
Headboard
Side
SIDERAIL R
Siderail
cleat

Tools required
Align the holes on the support leg and
middle platform assembly spine.
Tighten with 1 ¾” pan head screw
(Figure 3). Make sure to retract the
support leg leveler slightly so that it only
makes contact with the floor when
weight is applied to the fully assembled
bed.
Step 3: Install the support leg on the
Philips head screwdriver
Figure 4.
3
Middle platform
assembly
Install Platform
Assemblies
1 ½” pan
head screw
Figure 3.
Step 4: Install the platform assembly
Middle
Platform
Assembly
Support leg
Platform
spine
Install support leg
1 ¾” pan
head screw
Leveler
on middle platform
Align the holes on each end of the
platform assembly and the holes on the
side rail cleats (Figure 4). Tighten each
platform assembly and side rail with 1 ½”
pan head screws.
middle platform assembly Headboard
Footboard
Platform
assembly
Siderail
Cleat
Siderail
Cleat

Care Instructions
To care for and preserve the finish on your new Copeland Furniture piece, please keep the following
recommendations in mind.
While our furniture has been finished with a durable top coat, the surface may be sensitive to
dents and abrasions during the first 30 days in your home.
Treat the surface finish gently so it does not dent or chip. Tape or stickers should not be put on
the finish.
For general care use a soft cloth to dust the furniture.
Use damp cloth with a mild soap to clean-up spills or dirt. Dry the surface thoroughly.
Please do not use any polishes, waxes or solvents to clean the surface of the furniture. This holds
true for new Copeland Furniture pieces as well as items you may already have in your home.
Please do not place any candles directly on the surface of your furniture. The perfumes and dyes
in the candles may penetrate the finish.
Beds must be disassembled before moving to avoid damage. Never attempt to move the bed
while it is assembled.
If you have any questions or difficulties, please call us at the number below between the hours of 8:00 am and 4:30 pm eastern time.
156 Industrial Drive, Bradford, VT 05033 Tel: [phone] Fax: [phone] www.copelandfurniture.com