Seville Classics UltraHD UltraGuard 20238 User manual

TR160309
ASSEMBLY INSTRUCTIONS
UltraHD Rolling Cabinet (Model No. 20238)
28"W X 18" D X 34.5" H
(71.1cm x 45.7cm x 87.6cm)
Reference page 9 for special care and maintenance
of stainless steel

(pg 1 of 10)
(#12) Drawer
#2
#3
#1
#4
#5
#6
#7 #8
#34
#9
#10
#23
#12
#15
#13 #14
#18
#19
#12-1
#12-2
#12-3
#12-4#12-5 #15

PARTS LIST (pg 2 of 10)
(#7) Bottom Panel x 1 PC (#8) Middle Shelf x 1 PC
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer
service department (please refer to page 10 of 10).
(#5) Right Side Panel x 1 PC (#6) Front Frame x 1 PC
(#1) Stainless Steel Top x 1 PC (#2) Upper Back Panel x 1 PC
(#3) Bottom Back Panel x 1 PC
(#4) Left Side Panel x 1 PC

PARTS LIST
(pg 3 of 10)
(#12-4) Drawer Base Panel x 1 PC (#12-5) Drawer Back Panel x 1 PC
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer
service department (please refer to page 10 of 10).
(#12-2) Drawer Left Side Panel x 1 PC (#12-3) Drawer Right Side Panel x 1 PC
(#23) Magnet x 2 PCS (#12-1) Drawer Front Panel x 1 PC
(#9) Swivel Wheel with Brake x 2 PCS (#10) Swivel Wheel W/O Brake x 2 PCS

PARTS LIST (pg 4 of 10)
(#25-1) Wrench X 1 PC
(#19) Right Door x 1 PC (#34) Hook X 4 PCS
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer
service department (please refer to page 10 of 10).
(#13) Drawer Mat X 1 PC (#18) Left Door x 1 PC
(#14) SCREW A (M4 x 10) x 44 PCS (#15) SCREW B (M4 x 8) x 32 PCS
(#21) Screw Driver x 1 PC (#22) Key x 2 PCS

Step 1.
Step 2.
Step 3.
Step 4.
Attach the Right Panel (#5) to Front Frame (#6) and
The Stainless Steel Top (#1), Make sure the “Top” of
the Left Panel (#4) is on the Stainless Steel Top (#1)
and the screw holes are lined up to the Front Frame
(#6), Use Screwdriver (#21) and 6pcs Screw A (#14) to
tighten the Right Panel (#5) the Front Frame (#6) and
Stainless Steel Top (#1).
Locate the Front Frame (#6)and attach to the "Front"
of the Stainless Steel Top (#1), using 2pcs Screw A
(#14) and Screwdriver (#21) to tighten.
Note: The screw holes have some tolerance so make
sure that the top and sides of the Front Frame are
flushed with the Stainless Steel Top (#1) – this may
save time by avoiding having to make slight
adjustments later.
Install the Right Panel (#5).
UltraHD Rolling Cabinet (Model No. 20238)
(pg 5 of 10)
Install Front Frame (#6)
Install the Left Panel (#4)
Attach the Left Panel (#4) to the Front Frame (#6) and
the Stainless Steel Top (#1). Make sure the “Top” of
the Left Panel (#4) is on the Stainless Steel Top (#1)
and the screw holes are lined up to the Front Frame
(#6). Use Screwdriver (#21) and 6pcs Screw A (#14) to
tighten the Left Panel (#4) to the Front Frame (#6),
and then to Stainless Steel Top (#1).
Open the package, remove and place all parts to the
side. Then open the package of the Stainless Steel Top
(#1).
Note: The Stainless Steel Top is packed within an inner
cardboard box. Assemble the unit on top of this
cardboard box to minimize damage to the stainless
steel surface.
#1
Front
Back
#6
#14
#4
#14
#5
#14

Step 5.
Step 6.
Step 7.
Step 8.
UltraHD Rolling Cabinet (Model No. 20238)
(pg 6 of 10)
Install the Upper Back Panel (#2)
Attach the Upper Back Panel (#2) between the
Left Panel (#4) and Right Panel (#5). Make sure
the “Top” of the Upper Back Panel (#2) is on the
Stainless Steel Top (#1) as the sticker indicates.
Line up the screw holes and use 9pcs Screw A
(#14) to tighten up the Upper Back Panel to the
Stainless Steel Top (#1), Left Panel (#4) and Right
Panel (#5).
Install the Bottom Back Panel (#3)
Install Wheels (#9 and #10)
Attach Wheels (#9 and #10) to the Bottom Panel
(#7) and surrounding frame. Make sure the
Swivel Wheels with Brake are installed at the
front side. Use Wrench (#25-1) to tighten them.
Install the Bottom Panel (#7)
Attach the Bottom Panel (#7) to the Left Panel
(#4), Right Panel (#5), Front Frame (#6), Bottom
Back Panel (#3), line up screw holes and use 9pcs
Screw A (#14) to tighten.
Attach Bottom Back Panel (#3) between the Left
Panel (#4) and Right Panel (#5). Make sure the
“Top” of the Bottom Back Panel (#3) is to the
Upper Back Panel (#2) as the sticker indicates.
Line up the screw holes and use 8pcs Screw A
(#14) to tighten the Bottom Back Panel (#3) to the
Upper Back Panel (#2), Left Panel (#4) and Right
Panel (#5).
#14
#7
#14
#3
#14
#2
#9
#10

Step 9. Install Drawer Base Panel and Drawer Front
(#12-4 and #12-1 ).
Step 10. Install Drawer Side Panels (#12-2 and #12-3)
Step 11. Install Drawer Back Panels (#12-5)
WARNING:
Attach Drawer Side Panels (#12-2 and #12-3) to the
back of Drawer Front (#12-1). Make sure the Drawer
Side Panels (#12-2 and #12-3) are placed all the way
into the slot, making contact with the inner wall of the
front panel. Line up the screw holes and use 10pcs
Screw B (#15) to tighten them.
Attach the Drawer Back Panel (#12-5) to the rest of the
assembled drawer. Use 7pcs Screw B (#15) to tighten.
Pull out slides before placing the drawer into the
cabinet.
UltraHD Rolling Cabinet (Model No. 20238)
(pg 7 of 10)
Fit and attach Drawer Base Panel (#12-4) into the back
slot of stainless steel Drawer Front (#12-1), use 3pcs
Screw B (#15) to tighten.
Note: Do not fully tighten any one screw until all
screws are partially screwed in.
#12-1
#12-4
#15
#15
#12-2
#12-3
#15
#12-5

Step 12.
Step 13. Place Drawer Mat (#13) into Drawers
`
Step 14. Install Magnet (#23)
Place the Drawer Mat (#13) inside the drawer, on
top of the base panel as shown in the diagram.
Note: If there are gaps between the drawer
panels or the frame is not square, please pull out
the drawer and loosen the screws to make
adjustments.
Place (#23) Magnet onto the top and bottom of
front frame (#6) facing the front, use 4pcs Screw
A (#14) to tighten.
UltraHD Rolling Cabinet (Model No. 20238)
(pg 8 of 10)
Install Drawer (#12) into cabinet
1).
Pull out both slides for drawer. Hook the
drawer between both slides, make sure the slide
hooks are completely inserted into the square
holes on the drawer side panels.
2). Line up the screw holes, and using 4pcs Screw
B (#15) to tighten the drawer.
#12
#13
#15
#14 #23

Step 15. Install Middle Shelf (#8).
Step 16. Install the Left and Right Doors (#18 and #19)
`
Stainless Steel Maintenance:
These parts have an UltraGuard® fingerprint resistant finish. Do not
use traditional stainless steel cleaners on this unit. Lightly wipe off
once a month with clean warm water and a soft cloth (preferably a
micro fiber cloth). This is the safest formula to prevent new stains
from appearing over time and manage unwanted fingerprints or
grease marks. Remember to always wipe in the direction of the
surface grain (NEVER ACROSS) and always use a lint-free cloth. Once
the surface is clean, thoroughly wipe dry with a soft absorbent cloth.
1). Attach the Left Door (#18) to the unit using 4pcs
Screws B (#15) to tighten.
Note: The screw holes on the door hinge have
tolerance, enabling the door to be adjusted and
centered in the frame.
2). Install the Right Door (#19) the same way.
UltraHD Rolling Cabinet (Model No. 20238)
(pg 9 of 10)
1). Decide the height for the Middle Shelf (#8). Place
4pcs of (#34) Hook into the hook slot where each
corner of shelf should be placed. Make sure the
hooks supporting each shelf are at same height.
Note: The middle shelf needs a hook at each corner
to support it.
2). Place (#8) Middle Shelf into cabinet and push
down onto (#34) Hooks.
#8
#34
#18
#15
#19

customer service department at:
***Please visit our website or call and inquire about our additional UltraHD Line***
Model No. 16238
UltraHD Storage Cabinet
Model No. 16236
UltraHD Storage Cabinet
CONTACT INFORMATION
(pg 10 of 10)
Telephone: [phone] within USA
Hours: 9:00am - 4:30pm (Pacific Standard Time)
please contact our bilingual (English/Spanish)
Seville Classics, Inc.
19401 South Harborgate Way
Torrance, CA 90501
USA
*If you are missing any parts, have any questions, or need additional assistance in assembly,
UltraHD Line
Fax: [phone]
E-mail: [email protected]
Website & Online Store: www.sevilleclassics.com

Model No. 20215
UltraHD Trash Bin
Model No. 20255
UltraHD Tool Box
Model No. 20262
UltraHD Rolling Workbench
Model No. 20267
UltraHD Workcenter
UltraHD Line
Model No. 20206
UltraHD Workbench
Model No. 20204
UltraHD 6- Drawer Rolling
C bi t