Shark Lift-Away Garment Pro GS400 User manual

GS400
www.sharkclean.com
User’s Guide
fabric steamer
Lift-Away
Garment Pro
GS400_11_IB_E_120111_1.indd 1 12-01-11 9:46 AM

2
TOLL FREE: 1-800-798-7398
WHEN USING YOUR SHARK®
LIFT-AWAY GARMENT PRO FABRIC
STEAMER, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR LIFT-AWAY GARMENT PRO FABRIC
STEAMER.
DANGER OF SCALDING
Please use caution when using the fabric
steamer. The Wrinkle Eraser™pressing bar and the
steam emitted are very hot. The Wrinkle Eraser™
is hot as long as the unit is turned on and for 30
minutes after the unit has been turned off.
POLARIZED PLUG:
To reduce the risk of electric shock, this appliance
has a polarized plug (one blade is wider than the
other). As a safety feature, this plug will fit into
a polarized outlet only one way. If the plug does
not fit fully into the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to
install the proper outlet. Do
not attempt to defeat this
safety feature.
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
1. USE THE SYSTEM ONLY FOR ITS
INTENDED USE AS DESCRIBED IN THIS
MANUAL.
2. ONLY USE WATER. To extend the life of your
Lift-Away Garment Pro Fabric Steamer, we
recommend using distilled water especially if you
live in an area with hard tap water.
3. DO NOT add cleaning solutions, scented
perfumes, oils, or any other chemicals to the
water used in this appliance as this may damage
the unit or make it unsafe for use.
4. Use of any substances other than
manufacturer’s recommended accessories will
automatically void your warranty.
5. DO NOT use outdoors.
6. DO NOT leave the appliance unattended when
plugged in.
7. Always unplug the power cord from the
electrical outlet when not in use, when filling
the water tank and before cleaning.
7. Always unplug the power cord from the
electrical outlet when not in use, when filling
the water tank and before cleaning.
8. DO NOT allow to be used as a toy.
9. DO NOT put any objects into openings or
operate with any opening blocked.
10. DO NOT use on leather, suede, vinyl, plastic or
other delicate steam sensitive materials. Always
determine the colorfastness of any fabric before
using the fabric steamer by testing it on a small
portion of the garment’s underside.
11. This appliance and the accessories become
hot during use. Exercise care when changing
accessories and follow removal and changing
instructions as outlined in the manual. Do not
change frames while the unit is turned on. Turn
the unit off, wait for the Wrinkle Eraser™to
cool, and then change frames.
GS400_11_IB_E_120111_1.indd 2 12-01-11 9:46 AM

3
www.sharkclean.com
12. The fabric steamer can be used in a vertical or
horizontal motion. NEVER hold the steam head
down while at rest.
13. When cleaning the fabric steamer, unplug the
power cord and clean with a dry or damp cloth.
DO NOT pour water on the unit or use alcohol,
benzene or paint thinner on the unit.
14. NEVER attempt to steam clothing while it is
being worn.
15. To protect against a risk of fire, electric shock, or
injury:
a. To avoid circuit overload, DO NOT operate
another appliance on the same socket
(circuit) as the fabric steamer.
b. DO NOT immerse any part of the system in
water or other liquids.
c. DO NOT pull power cord to disconnect
from outlet; instead, grasp plug and pull to
disconnect.
d. DO NOT use extension cords or outlets
with inadequate current carrying capacity.
If an extension cord is absolutely necessary,
use a 15-ampere cord. Cords rated for less
amperage may overheat. Use care to arrange
the cord so that it cannot be pulled or
tripped over.
e. DO NOT operate the system with a
damaged cord or plug, or if the appliance
or any other part of the system has been
dropped or damaged.
f. DO NOT disassemble or attempt to
repair the fabric steamer. Return the
system to EURO-PRO Operating LLC
for examination and repair. Incorrect
reassembly or repair can cause a risk of
electrical shock or injury to persons when the
fabric steamer is used.
g. DO NOT handle plug or fabric steamer with
wet hands or operate without shoes.
h. DO NOT pull or carry by power cord, use
power cord as a handle, close a door on the
power cord, or pull the power cord around
sharp corners or edges.
i. DO NOT allow power cord to touch hot
surfaces.
j. ALWAYS disconnect the steamer from
electrical outlet when filling the water tank
or emptying and when not in use.
k. NEVER attempt to fill this unit under a
water faucet. Always use the funnel that is
provided.
l. Never turn the appliance over or on its side
when in use.
m. NEVER aim or direct steam towards people,
animals, or plants. The steam is very hot
and can cause burns. Burns can occur
from touching hot metal parts, steam,
steam bonnets or frames. There may be
condensation on the parts of the steamer
which may be hot.
n. DO NOT operate the product while
under the influence of drugs, alcohol or
medications.
o. DO NOT operate in the presence of
explosive and/or flammable fumes.
p. Store your appliance indoors in a cool, dry
area out of the reach of children.
q. Keep your work area well lit.
r. Let the steamer cool completely before
putting away. Loop cord loosely on the cord
hook on the telescopic pole.
s. Keep out of the reach of children.
SAVE THESE
INSTRUCTIONS
GS400_11_IB_E_120111_1.indd 3 12-01-11 9:46 AM

4
TOLL FREE: 1-800-798-7398
Welcome to the next generation of garment care!
The Lift-Away Garment Pro Fabric Steamer provides you the convenience of removing wrinkles
right on the hangers; and at the same time press the garments to get a completely finished look. The
Shark®powerful steam technology penetrates fibers, renews and freshens fabrics. The exclusive heated
Wrinkle Eraser™presses for a crisp finish and dries fibers to prevent re-wrinkling.
With the unique design to be able to steam the garment right on the hanger with the telescopic pole;
or lift off from the base to become a table top unit; or carry it around the home to steam upholstery to
have a healthy home, the Lift-Away Garment Pro Fabric Steamer is an all-in-one solution to make
you look the best in the easiest way.
Attaching the appropriate
accessory:
The unit comes assembled with a
small steam bonnet. The bonnet
must be attached at all times when
the unit is being used.
1Make sure the small steam
bonnet is in place. Loop one
side first and then stretch it
over to loop over the hook on
the other side. Make sure that
the steam bonnet is covering
the lip of the steam chamber
completely. (Fig. 1).
Fig. 1
TIP: Wipe away condensation
from the steam guard on the
bottom of the frame after
extended use.
USE FOR
BENEFITS
FRAME/
ACCESSORY
Upholstery/Delicate Fabric
Frame & Steam Bonnet
Best for: lace, velvet, silk, satin,
embellished or delicate garments
and upholstery
Specifically designed to protect
delicate fabric from high heat
Small Steam
Bonnet
The bonnet should
always be attached
during any use and with
any frame
The specially designed
pad protects fabrics
from water marks and
impurities
Bristle Brush
Frame
Best for cotton, wool,
linen, denim
Improves steam
penetration on heavy
fabrics without leaving
water marks
GS400_11_IB_E_120111_1.indd 4 12-01-11 9:46 AM

5
www.sharkclean.com
Quick Start Guide
ASSEMBLY
1 Set the base on the floor and
insert the telescopic pole section
(A) into the opening in the
base. Align the opening of the
telescopic pole with the opening
of the base and slide it in. Secure
the pole onto the base by turning
the connector clockwise. (fig. 2)
2 Insert the steam nozzle cradle/
handle (B) all the way down the
telescopic pole until it stops. The
cradle should face the front of
the base. (fig. 2)
3 Place the portable steamer on
the base. Make sure that it sits
flat. (fig. 3)
4 Attach the steam hose to the
steam unit by turning the
connector clockwise until it is
completely locked. Hang the
steam nozzle on the steam
nozzle cradle. (fig. 4)
NOTE: The hose will remain stiff
until heated.
5 Plug the steam hose power cord
(white) into the fabric steamer
receptacle which is on the right
side of the steamer. (fig. 5)
This provides the power to heat
up the Wrinkle Eraser™after
the main power cord (gray) is
plugged in.
fig. 5
fig. 4
fig. 3
fig. 2
A
B
GS400_11_IB_E_120111_1.indd 5 12-01-11 9:46 AM

6
TOLL FREE: 1-800-798-7398
fig. 6
PUSH
FILLING THE WATER TANK
1 Make sure the power switch is
OFF “0” then unplug the unit
from the power outlet.
2 Remove the water tank cap by
turning counter clockwise and
use the funnel that is provided to
fill the water tank to the max fill
line. (fig. 6)
3 Replace the cap on the filling
inlet. Push the cap down and
turn clockwise to lock. Steam will
not emit if the water tank cap is
not locked properly.
USING THE STEAMER
Stand Mode
1 Make sure the steam bonnet is in
place during all usage.
2 To lower the handle, push the
button on the side of the handle
to a locked position. (fig. 7)
Hang the garment on the
garment hook.
3 Adjust the garment clip bar up/
down to clip the bottom of the
garment for extra support.
(fig. 8)
4 Begin steaming in an up and
down motion.
Portable Mode
1 Remove the steamer from the
base by lifting it up.
2 Hold the steamer at waist level
in one hand or place on a table.
(Fig. 9)
3 Steam the fabric in an up and
down motion.
fig. 7
fig. 9
Quick Start Guide - cont.
fig. 8
PRESS
GS400_11_IB_E_120111_1.indd 6 12-01-11 9:46 AM

7
www.sharkclean.com
CONTENTS
Quick Start Guide 4
Assembly 6
Using your Fabric Steamer 8
Maintenance 10
Troubleshooting Guide 10
Warranty and Registration 11
Thank you
for purchasing
the Shark®
Lift-Away
Garment Pro
Fabric Steamer
This manual covers model number:
G S 4 0 0 11
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz.
Power: 1500 Watts
Water Capacity: 1100 ml (37 oz.)
GS400_11_IB_E_120111_1.indd 7 12-01-11 9:46 AM

8
TOLL FREE: 1-800-798-7398
Getting Started
First things first, you need to
know what’s in the box you
just opened:
AFabric Steamer
BSteam hose/steam nozzle
with steam bonnet (Bonnet is
removable)
CTelescoping Garment Pole
DSteam Nozzle Cradle with
Swivel Handle and Garment
Hook
EUnit Base
FUpholstery/Delicate Fabric
Frame
GUpholstery/Delicate Fabric
Bonnet
HBristle Brush
IFilling Funnel
A
B
C
D
E
F
G
JSteam Nozzle with Wrinkle
Eraser™
KPower Indicator
LTelescopic Garment Pole
Adjustment Clips
MSteam Hose with Fabric Cover
NAdjustable Garment Clip Bar
OHose Connection
PSteam Hose Power Cord (White)
QSteam Hose Power Cord
Receptacle
RCarrying Handle
SWater Tank Cap
TPower Switch
U2 Legs
V2 Roller Wheels
YOUR FABRIC STEAMER FEATURES
H
Q
T
N
J
L
S
R
M
O
P
K
U
V
I
GS400_11_IB_E_120111_1.indd 8 12-01-11 9:46 AM

9
www.sharkclean.com
Assembly
ASSEMBLY
1 Set the base on the floor and
insert the telescopic pole section
(A) into the opening in the
base. Align the opening of the
telescopic pole with the opening
of the base and slide it in. Secure
the pole onto the base by turning
the connector clockwise. (fig. 1)
2 Insert the steam nozzle cradle/
handle (B) all the way down the
telescopic pole until it stops. The
cradle should face the front of
the base. (fig. 1)
3 Place the portable steamer on
the base. Make sure that it sits
flat. (fig. 2)
4 Attach the steam hose to the
steam unit by turning the
connector clockwise until it is
completely locked. Hang the
steam nozzle on the steam
nozzle cradle. (fig. 3)
NOTE: The hose will remain stiff
until heated.
5 Plug the steam hose power cord
(white) into the fabric steamer
receptacle which is on the right
side of the steamer. (fig. 4)
This provides the power to heat
up the Wrinkle Eraser™after
the main power cord (gray) is
plugged in.
fig. 4
fig. 3
fig. 2
fig. 1
A
B
GS400_11_IB_E_120111_1.indd 9 12-01-11 9:46 AM

10
TOLL FREE: 1-800-798-7398
fig. 5
Filling the water tank
1 Make sure the power switch is
OFF “0” then unplug the unit
from the power outlet.
2 Remove the water tank cap by
turning counter clockwise and
use the funnel that is provided to
fill the water tank to the max fill
line. (fig. 5)
3 Replace the cap on the filling
inlet. Push the cap down and
turn clockwise to lock.
IMPORTANT: The water cap must
be locked into place securely to
allow proper flow of water. Once
turned on, steam will not emit if the
water cap is not secure.
WARNING: Do not fill the water
tank when the unit is plugged in to
an electrical outlet.
WARNING: The steam is hot! Be
careful not to touch the steam nozzle
when the unit is turned on or has
been in use.
IMPORTANT: When assembling
your fabric steamer, there may be a
little water in the water tank. This
is because we test all our fabric
steamers 100% before you buy
them, so you get a quality Shark®
Steam product.
When using the upholstery/
delicate fabric frame:
NOTE: Remember, DO NOT
use the fabric steamer without
the small steam bonnet in
place.
4Attach the Upholstery/
Delicate Fabric bonnet to the
frame, then attach the frame
to the unit. Pull either side of
the bonnet over the top of the
frame and secure the bottom
of the bonnet to the frame.
(Fig. 7) Then, attach the
frame to the fabric steamer
by placing the top of the
frame into the notch above
the Wrinkle Eraser™. Next,
secure the rounded end of the
frame underneath the steam
nozzle and snap into place.
When using the bristle
brush frame:
NOTE: The bristle brush
offers better steam
penetration for heavy fabrics
without leaving water marks.
5 Attach the bristle brush frame
to the fabric steamer nozzle.
Make sure that the small steam
bonnet is attached. (Fig. 8)
Fabric Recommendations:
Heavy fabrics, cotton, wool,
canvas, denim.
CAUTION: Do not use the
bristle brush on delicate fabrics.
Attaching the accessories:
IMPORTANT:Use caution
when changing the frame
when the unit is hot. The
frames are designed with
a steam guard around the
bottom to provide protection
from heat when placing or
removing the frames.
The small steam bonnet must
be attached at all times during
usage. (Fig. 6)
This bonnet should only be
removed for washing by hand,
if necessary (see page 12 for
care instructions).
Practice makes perfect!
It takes time to master
the garment steaming
techniques.
For best results, tilt the
steamer forward slightly
and press the Wrinkle
Eraser™ directly on the
garment.
The seam on the frame must line up
with the seam on the unit for proper
use and safety. The frame will snap
into place, double check to make
sure the seams are aligned.
Using Your Lift-Away Garment Pro Fabric Steamer
PUSH
Fig. 6
Fig. 7 Fig. 8
GS400_11_IB_E_120111_1.indd 10 12-01-11 9:46 AM