Sharp GS-XP9FGR User manual

GS-XP9FGR
GS-XP12FGR
GS-XP18FGR
GS-XPM9FGR
GS-XPM12FGR
GS-XPM18FGR
GS-XP9FGR GS-XPM9FGR
GS-XP12FGR GS-XPM12FGR
GS-XP18FGR GS-XPM18FGR
FLOOR STANDING
TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
ENGLISH
ESPAÑOL
ITALIANO
PORTUGUÊS
R
FRANÇAIS
* Plasmacluster is trademark of
SHARP Corporation.
INDOOR UNIT
UNIDAD INTERIOR
UNITÀ INTERNA
ZIMMERGERÄT
UNITE INTERIEURE
∑Ç ÜN∑TE
CONDIZIONATORE D’ARIA A
PAVIMENTO
MANUALE DI ISTRUZIONI
AIRE ACONDICIONADO
CONSUELA DE SUELO
MANUAL DE INSTRUCCIONES
CLIMATISEUR SPLIT CONSOLE
MURALE
NOTICE D’UTILISATION
Air Conditioner
TÜRKÇE
TABANDA DURAN T∑P ODA
KL∑MASI
KULLANMA KILAVUZU
AR CONDICIONADO DE CHÃO
MANUAL DE OPERAÇÃO

EN
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust
bin!
Used electrical and electronic equipment must be treated separately and in
accordance with legislation that requires proper treatment, recovery and recycling of
used electrical and electronic equipment.
Following the implementation by member states, private households within the EU
states may return their used electrical and electronic equipment to designated
collection facilities free of charge*. In some countries* your local retailer may also
take back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please
dispose of these separately beforehand according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes
the necessary treatment, recovery and recycling and thus prevent potential negative
effects on the environment and human health which could otherwise arise due to
inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the
correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of
charge to the dealer, even if you don’t purchase a new product. Further collection
facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users.
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the
product. You might be charged for the costs arising from take-back and recycling.
Small products (and small amounts) might be taken back by your local collection
facilities.
For Spain: Please contact the established collection system or your local authority for
take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for
the correct method of disposal.
Attention: Your product is
marked with this symbol. It
means that used electrical
and electronic products
should not be mixed with
general household waste.
There is a separate
collection system for these
products.

ENGLISH
E-1
ENGLISH
Thank you for purchasing a SHARP air conditioner. Please read this manual carefully
before operating the product.
• IMPORTANT SAFETY INSTRUCTIONS...E-1
• PART NAMES............................................E-3
• SETTING DEODORANT FILTERS............E-5
• USING THE REMOTE CONTROL.............E-6
• BASIC OPERATION ..................................E-8
• ADJUSTING THE AIR FLOW DIRECTION ...... E-10
• AIR OUTLET SELECTION.........................E-11
• FULL POWER OPERATION......................E-12
CONTENTS
• ONE-HOUR OFF TIMER ...........................E-12
• PLASMACLUSTER OPERATION..............E-13
• TIMER OPERATION..................................E-14
• MAIN UNIT OPERATION...........................E-16
• MAINTENANCE .........................................E-16
• ADDITIONAL NOTES ON OPERATION .......... E-19
• TIPS ON SAVING ENERGY ......................E-19
• BEFORE CALLING FOR SERVICE...........E-20
WARNINGS FOR USE
1Donotpullordeformthepowersupplycord.Pullingandmisuseofthepowersupplycord
can result in damage to the unit and cause electrical shock.
2Be careful not to expose your body directly to the outlet air for a long time. It may affect
your physical conditions.
3Whenusingtheairconditionerforinfants,children,elderly,bedridden,ordisabledpeople
make sure the room temperature is suitable for those in the room.
4Never insert objects into the unit. Inserting objects can result in injury due to the high
speed rotation of internal fans.
5Ground the air conditioner without fail. Do not connect the grounding wire to gas pipe,
waterpipe, lightning rodortelephone groundingwire.Incompletegrounding maycause
electric shock.
6If anything is abnormal with the air conditioner (ex. a burning smell), stop the operation
immediately and turn the circuit breaker OFF.
7Theapplianceshallbeinstalledinaccordancewithnationalwiringregulations.Improper
cable connection can cause the power supply cord, plug and the electrical outlet to
overheat and cause fire.
8Ifthesupplycordisdamaged,itmustbereplacedbythemanufactureroritsserviceagent
or a similarly qualified person in order to avoid a hazard. Use only the manufacture-
specified power cord for replacement.
WARNINGS FOR INSTALLATION/REMOVAL/REPAIR
• Donot attempt toinstall/remove/repairthe unitbyyourself.Incorrect workwillcause electric
shock, water leak, fire etc. Consult your dealer or other qualified service personnel for the
installation/removal/repair of the unit.
IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS
CAUTIONS FOR USE
1Open a window or door periodically to ventilate the room, especially when using gas
appliances. Insufficient ventilation may cause oxygen shortage.
2Do not operate the buttons with wet hand. It may cause electric shock.
3For safety, turn the circuit breaker off when not using the unit for an extended period of
time.
4Check the outdoor unit mounting rack periodically for wear and to make sure it is firmly
in place.
5Do not put anything on the unit nor step on it. The object or the person may fall down or
drop, causing injury.
6This unit is designed for residential use. Do not use for other applications such as in a
kennel or greenhouse to raise animals or grow plants.
7Do not place a vessel with water on the unit. If water penetrates into the unit, electrical
insulations may deteriorate and cause electric shock.
8Do not block the air inlets nor outlets of the unit. It may cause insufficient performance
or troubles.
9Be sure to stop the operation and turn the circuit breaker off before performing any
maintenance or cleaning. A fan is rotating inside the unit and you may get injured.
10
Do not splash or pour water directly on the unit. Water can cause electrical shock or
equipment damage.
11
This appliance is not intended for use by young children or infirm persons without
supervision.
Young children should be supervised to ensure that they do not play with the appliance.
CAUTIONS FOR LOCATION/INSTALLATION
• Make sure to connect the air conditioner to power supply of the rated voltage and
frequency.
Use of a power supply with improper voltage and frequency can result in equipment
damage and possible fire.
• Do not install the unit in a place where inflammable gas may leak. It may cause fire.
Install the unit in a place with minimal dust, fumes and moisture in the air.
• Arrange thedrainhosetoensuresmoothdrainage. Insufficientdrainagemay cause wetting
of the room, furniture etc.
• Make sure a leak breaker or a circuit breaker is installed, depending on the installation
location, to avoid electrical shock.
E-2

ENGLISH
PART NAMES
1AIR OUTLET SELECTION
Lamp (green)
2AIR OUTLET SELECTION
button
3POWER. Button
4Air Filters
5Upper air outlet
6Horizontal Adjustment
Louvres
7Vertical Adjustment Louvres
8PLASMACLUSTER Lamp
(blue)
9OPERATION Lamp (red )
0TIMER Lamp (orange )
qRECEIVER Window
wInlet (Air)
eDeodorant Filters
rFront Grille
tRemote Control
yLower air outlet
INDOOR UNIT
E-3
NOTE: Actual units might vary slightly from those shown above.
1
2
3
4
5
6
7
8
9
0
q
w
e
r
w
7
6
y
t

REMOTE CONTROL
1TRANSMITTER
2DISPLAY (Liquid Crystal Display)
3PLASMACLUSTER Button
4ON/OFF Button
5THERMOSTAT Button
6FULL POWER Button
7MODE Button
8ONE-HOUR OFF TIMER Button
9TIMER ON Button (for setting the timer)
0TIMER OFF Button (for setting the timer)
qTIME ADVANCE Button
wTIME REVERSE Button
eFAN Button
rTIMER SET/CANCEL Button
tIndicates BATTERY COMPARTMENT is
below this mark
yCLOCK Button
uSWING Button
gTIMER ON INDICATOR/CLOCK
Indicates the on timer preset time or current
time.
hTIMER OFF INDICATOR
Indicates the preset time for off timer or one-
hour off timer.
E-4
iPLASMACLUSTER SYMBOL
oMODE SYMBOLS
: AUTO : COOL
: HEAT : DRY
pTHERMOSTAT SETTING FOR AUTO AND
DRY MODES
aTEMPERATURE INDICATOR
sTRANSMITTING SYMBOL
dFULL POWER SYMBOL
fFAN SPEED SYMBOLS
: AUTO : LOW
: HIGH : SOFT
L.C.D. REMOTE CONTROL DISPLAY
1
2
3
4
5
6
7
8
9
0
q
w
e
r
t
y
u
i
o
p
a
s
d
f
g
h
SWING
FAN
MODE
SET/C
1h
PART NAMES

ENGLISH
SETTING DEODORANT FILTERS
E-5
The deodorant filters are packed as accessory of this unit. During operation of the
air conditioner, the filters absorb odor elements from the air.
1Open the front grille.
Hold the two " " marked corners on
the front grille and pull it toward yourself
to open.
2Take out the air filters.
3Set the deodorant filters under the filter
stoppers located on the air filters.
4Reinstall the air filters in the original po-
sitions.
5Close the front grille.
Press the two " "marked positions on
the front grille to lock it in place.
Precautions
• The deodorant filters are sealed in a plastic bag to keep their deodorant effect.
Do not open the bag until using the filters. (Otherwise the filters life may get
shorter.)
• Do not expose the filters to direct sunlight. (Otherwise they may deteriorate.)
air filter mark
front grille
deodorant filterair filter

1Remove the remote control
cover.
2Insert batteries in the compart-
ment, making sure the ±and
—polarities are correctly
aligned.
• The display indicates “AM
6:00” when batteries are prop-
erly installed.
3Reinstall the cover.
USING THE REMOTE CONTROL
E-6
NOTES:
• The battery life is approximately one year in normal use.
• When you replace the batteries, always change both batteries, and make sure they
are the same type.
• If the remote control does not operate properly after replacing the batteries, take
out the batteries and reinstall them again after 30 seconds.
• If you will not be using the unit for a long time, remove the batteries from the remote
control.
Point the remote control towards the unit’s signal receiver window and
press the desired button. The unit generates a beep when it receives the
signal.
• Make sure there is no cur-
tain or other object between
the remote control and the
unit.
• The remote control can send
signals from up to 7 metres
away.
LOADING BATTERIES Use two size-AAA (R03) batteries.
HOW TO USE THE REMOTE CONTROL
Remote control
cover
+
-
+
-

ENGLISH
E-7
CAUTION
• Do not allow the signal receiver window to receive strong direct sunlight, since it can
adversely affect its operation. If the signal receiver window is exposed to direct sunlight,
close a curtain to block the light.
• Using a fluorescent lamp with a quick starter in the same room may interfere with
transmission of the signal.
• The unit can be affected by signals transmitted from the remote control of a television,
VCR or other equipment used in the same room.
• Do not leave the remote control in direct sunlight or near a heater. Also, protect the unit
and remote control from moisture and shock which can discolour or damage them.
SET CURRENT CLOCK TIME
There are two clock modes:
12-hour mode and 24-hour
mode.
1To set to the 12-hour mode, press the
CLOCK button once in the first step.
To set to the 24-hour mode, press the
CLOCK button twice in the first step.
2Press the TIME ADVANCE or REVERSE
button to set the current time.
• Keep the button pressed to advance
or reverse the time display quickly.
3Press the SET/C button.
• The colon (:) blinks to indicate that the
clock is functioning.
NOTE:
• The current time cannot be set when the
timer is operating.
1
2
3
Example: 5 o’clock in the afternoon
Clock Display
12-hour mode PM 5:00
24-hour mode 17:00
SWING
FAN
MODE
SET/C
1h

SWING
FAN
MODE
SET/C
1h
Press the THERMOSTAT button to set the
desired temperature.
• In the AUTO and DRY
modes, the tempera-
ture can be changed
in 1°C increments
within the range of 2°C
higher to 2°C lower
from the temperature
automatically deter-
mined by the air con-
ditioner.
• In the COOL and HEAT modes, the tempera-
ture can be set within the range of 18 to 32°C
1
E-8
BASIC OPERATION
2Press the ON/OFF button to start opera-
tion.
• The red OPERATION lamp ( ) on the unit
will light.
3
4
1
5
2
3
Press the MODE button to select the op-
eration mode.
AUTO HEAT COOL DRY
5
• In the DRY mode, the fan speed is preset to
AUTO and cannot be changed.
To turn off the unit, press the ON/OFF but-
ton again.
• The red OPERATION lamp ( ) on the unit
will turn off.
Press the FAN button to set the desired fan
speed. AUTO SOFT LOW HIGH
(Example: 1°C higher)
(Example: 2°C lower)
4
C
C
When using your air-conditioner with multi-system
(GS-XPM9FGR,GS-XPM12FGR,GS-XPM18FGR)
With a multi system air conditioner, multiple indoor units can be connected to one outdoor
unit. When the setting mode differs among indoor unit(s), the indoor unit(s) operated later
may not work.
• When the indoor unit(s) is/are operating in HEAT mode, the remaining unit(s) can not operate in
COOL or DRY mode.
• When the indoor unit(s) is/are operating in COOL or DRY mode, the remaining unit(s) can not
operate in HEAT mode.
When the mode of the indoor unit(s) later operated is/are different from those which is /are in
operation, after a few seconds, a long BEEP will be emitted and the OPERATION lamp and
TIMER lamp will blink alternately. This shows that the later operated unit(s) is/are not working. In
such case, change the mode to the same mode which the other indoor unit(s) is/are operating in.

ENGLISH
E-9
• During operation, if the outdoor temperature changes, the temperature settings will
automatically slide as shown in the chart.
• During seasons when you need COOLING at daytime and HEATING at night, or if
the room temperature should become extremely higher than the temperature set-
ting, due to supplementary heating equipment, the mode will automatically switch
between HEAT and COOL mode to keep the comfortable room temperature. (MODE
CHANGEOVER)
TIPS ABOUT AUTO MODE
(GS-XP9FGR,GS-XP12FGR,GS-XP18FGR)
In the AUTO mode, the temperature setting and mode are automatically se-
lected according to the room temperature and outdoor temperature when the
unit is turned on.
Modes and Temperature Settings
the figures in ( ) are temperature settings






 













 
 

• During operation, if the outdoor temperature changes, the temperature settings will
automatically slide as shown in the chart.
• Mode of the unit operated first will have priority over unit(s) without reference to the
chart.
TIPS ABOUT AUTO MODE
(GS-XPM9FGR,GS-XPM12FGR,GS-XPM18FGR)
In the AUTO mode, the temperature setting and mode are automatically se-
lected according to the room temperature and outdoor temperature when the
unit is turned on.
Modes and Temperature Settings
the figures in ( ) are temperature settings





 


 









 
 


E-10
ADJUSTING THE AIR FLOW DIRECTION
VERTICAL AIR FLOW DIRECTION
Hold the horizontal adjustment
louvre levers as shown in the dia-
gram and adjust the air flow di-
rection.
Press the SWING button.
• The vertical adjustment louvre for upper outlet
will change its angle continuously.
Press the SWING button again when the
vertical adjustment louvre for upper outlet
is at the desired position.
• The louvre will stop moving within the range
shown in the diagram.
• The adjusted position will be memorized and will
be automatically set to the same position when
operated the next time.
NOTE:
The vertical adjustment louvre for lower outlet is
automatically set and cannot be changed.
CAUTION
Never attempt to adjust the vertical adjustment louvres manually.
• Manual adjustment of the vertical adjustment louvre can cause the unit to malfunction when the
remote control is used for adjustment.
• When the vertical adjustment louvre is positioned at the lowest position in the COOL or DRY mode
for an extended period of time, condensation may result.
Do not adjust the horizontal adjustment louvre to the extreme left or right in the COOL mode
with the fan speed set to “SOFT( )” for an extended period of time.
Condensation may form on the louvres.
HORIZONTAL AIR FLOW DIRECTION
1
2
SWING
FAN
MODE
SET/C
1h
1
2
Louvre levers

ENGLISH
When outlet air
temperature is low.
(operation start up, de-
icing)
Upper air outlet
AIR OUTLET SELECTION
E-11
Press AIR OUTLET SELECTION button, and choose " (Upper and lower automatic
air outlets)" or " (Upper air outlet)".
When setting air outlet to ".
Air is blown out automatically from the upper and
lower air outlet as shown below.
MODE CONDITION AIR OUTLET
COOL
When room temperature
ishigherthantemperature
setting.
DRY Upper air outlet
HEAT When outlet air
temperature is high. Upperandlower airoutlet.(Lower
airflowisgreater
than upper air
flow)
When setting air outlet to " ".
Airisblownout fromtheupperairoutlet,regardless
to the mode and condition.
AIR OUTLET
SELECTION
button
Upper and lower air outlet Upper air outlet
TIPS ABOUT UPPER AND LOWER AUTOMATIC AIR OUTLET
Air outlet is automatically selected according to room temperature and outlet air temperature,
to keep comfortable room condition.
During cooling operation
When room temperature is higher than
temperature setting, air is blown out from
upper and lower air outlet to make the
room cool rapidly. When room tempera-
ture is close to temperature setting, air is
blown out from upper air outlet to avoid
feeling the cold air flow.
During heating operation
When outlet air temperature is low, air is
blown out from upper air outlet to pre-
vent cold air blowing to the floor. When
outlet air temperature becomes high, air
is blown out from both air outlet with
main air flow from lower outlet to deliver
warm air to the floor.
COOL mode HEAT mode
Upper and lower
air outlet.
When room temperature
is close to temperature
setting. Upper air outlet

E-12
FULL POWER OPERATION
In this operation, the air conditioner works at maximum power to make the room cool
or warm so rapidly that you can use it just after you come home.
1Press the ONE-HOUR OFF TIMER button.
• The remote control displays “ ”.
• The orange TIMER lamp ( ) on the unit will light up.
• The unit will stop operating after one hour.
TO CANCEL
Press the TIMER CANCEL (SET/C) button.
• The orange TIMER lamp ( ) on the unit will turn off.
Alternatively, turn the unit off by pressing the ON/
OFF button.
• The red OPERATION lamp ( ) and the orange
TIMER lamp ( ) on the unit will turn off.
1
When the ONE-HOUR OFF TIMER is set, the unit will automatically turn off after one
hour.
ONE-HOUR OFF TIMER
1To activate the FULL POWER operation, press the
FULL POWER button during operation.
• The remote control will display “ ”.
• The temperature display will go off.
TO CANCEL
Press the FULL POWER button again.
• FULL POWER operation will also be cancelled when
the operation mode is changed, or when the unit is
turned off.
NOTE:
• You cannot set the temperature or fan speed during the FULL POWER operation.
NOTES:
• The ONE-HOUR OFF TIMER operation has priority over TIMER ON and TIMER OFF
operations.
• If the ONE-HOUR OFF TIMER is set while the unit is not operating, the unit will operate for
an hour at the formerly set condition.
• If you wish to operate the unit for another hour before the ONE-HOUR OFF TIMER is
activated, press the ONE-HOUR OFF TIMER button again during operation.
• If TIMER ON and/or TIMER OFF are set, TIMER CANCEL button cancels every setting.
1
PM
FAN
MODE
1h

ENGLISH
E-13
1
PLASMACLUSTER OPERATION
1During operation, press the PLASMACLUSTER
button.
• The remote control will display “ ”.
• The blue PLASMACLUSTER lamp on the unit will light
up.
TO CANCEL
Press the PLASMACLUSTER button again.
• The PLASMACLUSTER lamp on the unit will turn off.
NOTES:
• Use of the PLASMACLUSTER operation will be memorized, and it will be activated the next
time you turn on the air conditioner.
To perform the PLASMACLUSTER operation without accompanying heat, cool
or dry mode, press the PLASMACLUSTER button while the unit is not operat-
ing.
• The mode symbol of the remote control will go off and fan speed can not be set to AUTO.
• With multi-system models (GS-XPM9FGR/GS-XPM12FGR/GS-XPM18FGR), you may feel
warm air blown out from the unit when HEATING is performed with unit in other room. In
this case, indoor fan will not operate continuously.
The Plasmacluster ion generator inside the air conditioner will release positive and
negative Plasmacluster ions into the room.
Approximatelythesame numbersofpositive andnegativeions releasedintothe airwill
reduce some airborne mold.

1Press the TIMER OFF ( ) button.
2The TIMER OFF indicator will blink; press the
TIME ADVANCE or REVERSE buttons to set
the desired time. (The time can be set in 10-
minute increments.)
3Point the remote control at the signal receiver
window on the unit and press the TIMER SET
(SET/C) button.
• The orange TIMER lamp ( ) on the unit will
light.
• The unit will generate a beep when it receives the
signal.
NOTE:
Before setting the timer, make sure the clock is properly set with the current time.
TIMER OPERATION
TIMER OFF
Cancel the TIMER setting first, then set it
again.
TO CHANGE TIME SETTING
TO CANCEL TIMER MODE
Press the TIMER CANCEL (SET/C) button.
• The orange TIMER lamp ( ) on the unit will
turn off.
• The current clock
time will be dis-
played on the re-
mote control.
TIPS ABOUT TIMER OFF OPERATION
When the TIMER OFF mode is set, the
temperature setting is automatically
adjusted to prevent the room from
becoming excessively hot or too cold
while you sleep. (Auto Sleep function)
COOL/DRY MODE:
•One hour after the timer operation begins,
the temperature setting rises 1°C higher
than the original temperature setting.
HEAT MODE:
•One hour after the timer operation begins,
the temperature setting drops 3°C lower
than the original thermostat setting.
2
3
1
NOTE:
• If any TIMER ON, TIMER OFF and ONE-HOUR
OFF TIMER are set, the TIMER CANCEL button
cancels all settings.
E-14
SWING
FAN
MODE
SET/C
1h
SWING
FAN
MODE
SET/C
1h

ENGLISH
1Press the TIMER ON ( ) button.
2The TIMER ON indicator will blink; press the TIME
ADVANCE or REVERSE buttons to set the de-
sired time. (The time can be set in 10-minute
increments.)
3Point the remote control at the signal receiver
window on the unit and press the TIMER SET
(SET/C) button.
• The orange TIMER lamp ( ) on the unit will light.
• The unit will generate a beep when it receives the
signal.
4Select the operation condition.
Example:
To stop operation at 11:00 p.m. and resume operation
(With the same mode and temperature settings) to turn
on the unit by 7:00 a.m.
1Set the TIMER OFF to 11:00 p.m. during operation.
2Set the TIMER ON to 7:00 a.m.
The arrow ( or ) between the TIMER ON indicator
and the TIMER OFF indicator shows which timer will
activate first.
E-15
NOTES:
• You cannot programme the ON-TIMER and OFF-TIMER to operate the unit at different tempera-
tures or other settings.
• Either timer can be programmed to activate prior the other.
You can use the ON and OFF timers in combination.
COMBINED USE OF ON AND OFF TIMERS
2
1
3
TIMER ON
SWING
FAN
MODE
SET/C
1h
NOTE:
• The unit will turn on prior to the set timer to allow the
room to reach the desired temperature by the pro-
grammed time. (Awaking function)

MAINTENANCE
MAINTENANCE AFTER AIR
CONDITIONER SEASON
1Operate the unit in the COOL
mode, temperature setting 32°C,
for about half a day to allow the
mechanism to thoroughly dry.
2Stop the operation and unplug
the unit. Turn off the circuit
breaker, if you have one exclu-
sively for the air conditioner.
3Clean the filters, then reinstall
them.
MAINTENANCE BEFORE
AIR CONDITIONER SEASON
1Make sure that the air filters are
not dirty.
2Make sure that nothing obstructs
the air inlet or outlet.
3Check the outdoor mounting rack
periodically for wear and to make
sure it is firmly in place.
E-16
MAIN UNIT OPERATION
Use this operation when the remote control is not available.
TO TURN ON
Press the POWER button on the unit.
• The red OPERATION lamp ( ) on the unit
will light and the unit will start operating in
the AUTO mode.
• The fan speed and temperature setting are
set to AUTO.
TO TURN OFF
Press the POWER button again.
• The red OPERATION lamp ( ) on the unit
will turn off.

ENGLISH
CLEANING THE UNIT AND THE REMOTE CONTROL
E-17
MAINTENANCE
Wipe them with a soft cloth.
• Do not directly splash or pour water on them. We can cause electrical shock or
equipment damage.
• Do not use hot water, thinner, abrasive powders or strong solvents.
The front grille can also be removed
Be sure to stop the operation and turn off the circuit breaker before performing any
maintenance.
1OPEN THE FRONT GRILLE
Hold the two " " marked corners
on the front grille and pull it toward
yourself to open.
2REMOVE THE AIR FILTERS
3REMOVE THE FRONT GRILLE
Lift the front grille upward as shown
in picture.
4CLEAN THE FRONT GRILLE
Wipe the front grille with a soft
cloth. If the front grille is dirty, wash
it with warm water and a mild deter-
gent. Dry the front grille completely
in the shade before reinstalling.
5REPLACE THE FRONT
GRILLE
1Fit the both lower shafts into
the lower shaft receivers.
2Close the front grill and lift it to
hook both upper shafts into the
upper shaft receivers.
6REINSTALL THE AIR FILTERS
7CLOSE THE FRONT GRILLE
Press the two " " marked posi-
tions on the front grille to lock it in
place.
mark
air filter
front grille
upper shaft
upper shaft
receiver
lower shaft
lower shaft
receiver
1
2
3
5
6
7
2
1

E-18
MAINTENANCE
CLEANING THE FILTERS The air filters should be cleaned every two weeks.
1OPEN THE FRONT GRILLE
Hold the two " " marked corners on the front
grille and pull it toward yourself to open.
2REMOVE THE AIR FILTERS
3TAKE OFF THE DEODORANT FILTERS
FROM THE AIR FILTERS
4CLEAN THE AIR FILTERS
Use a vacuum cleaner to remove dust. If the
filters are dirty, wash them with warm water and
a mild detergent. Dry filters in the shade before
reinstalling.
5SET THE DEODORANT FILTERS
6REINSTALL THE AIR FILTERS
7CLOSE THE FRONT GRILLE
Press the two " " marked positions on the
front grille to lock it in place.
CLEANING THE DEODORANT FILTERS The deodorant filters should be
cleaned every two weeks.
1REMOVE THE AIR FILTERS
2CLEAN THE DEODORANT FILTERS
1 Take off the deodorant filters from the air filters.
2 Soak the deodorant filters in mild detergent dilu-
tion for 10 to 20 minutes. Rinse thoroughly with
water, dry completely under sunlight.
3 Set the clean deodorant filters, under the filter
stoppers located on the air filters.
3REINSTALL THE AIR FILTERS
NOTE:
• Replacement is necessary at the interval of 3 years, as the deodorising effect will deteriorate.
The new filters are available at your nearest dealer.
Replacement filter: Type AZ-F900G
Disposal of Filters
Please dispose of replaced filters according to the local disposal laws and regulations.
Deodorant filter material: (Polyester)
mark
air filter
deodorant filter