Sharp EL1750PIII - Printing Calculator,... User manual

EL-1750P III
ELECTRONIC PRINTING CALCULATOR
DRUCKENDER TISCHRECHNER
CALCULATRICE IMPRIMANTE ÉLECTRONIQUE
CALCULADORA IMPRESORA ELECTRÓNICA
CALCOLATRICE ELETTRONICA STAMPANTE
ELEKTRONISK SKRIVANDE OCH VISANDE RÄKNARE
ELEKTRONISCHE REKENMACHINE MET AFDRUK
CALCULADORA ELETRÔNICA COM IMPRESSORA
NAUHALASKIN
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE MANEJO
MANUALE DI ISTRUZIONI
BRUKSANVISNING
GEBRUIKSAANWIJZING
MANUAL DE INSTRUÇÕES
KÄYTTÖOHJE
ENGLISH ............................................................... Page 2
CALCULATION EXAMPLES ................................. Page 135
DEUTSCH .............................................................. Seite 16
RECHNUNGSBEISPIELE ..................................... Seite 135
FRANÇAIS ............................................................. Page 31
EXEMPLES DE CALCULS .................................... Page 136
ESPAÑOL .............................................................. Página 46
EJEMPLOS DE CÁLCULOS ................................. Página 137
ITALIANO .............................................................. Pagina 61
ESEMPI DI CALCOLO ........................................... Pagina 137
SVENSKA .............................................................. Sida 76
RÄKNEEXEMPEL .................................................. Sida 138
NEDERLANDS ...................................................... Pagina 90
REKENVOORBEELDEN ....................................... Pagina 138
PORTUGUÊS ........................................................ Página 105
EXEMPLOS DE CÁLCULOS ................................. Página 139
SUOMI ................................................................... Sivu 120
LASKENTAESIMERKKEJÄ ................................... Sivu 139
EL-1750PIII(LCO)-Cover-1 04.9.1, 9:28 AM1

Notes for handling Lithium batteries:
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Hinweise zur Handhabung von Lithium-Batterien:
VORSICHT
Bei Verwendung einer uneeigneten Ersatzbatterie besteht
Explosionsgefahr.
Nur durch den gleichen oder einen vom Hersteller empfohlenen
gleichwertigen Typ ersetzen.
Verbrauchte Batterien gemäß Herstelleranleitung entsorgen.
Remarques sur la manipulation des piles au lithium:
ATTENTION
Danger d’explosion de la pile si elle n’est pas remplacée correctement.
Remplacez-la uniquement par le même type de pile ou un type
équivalent recommandé par le fabricant.
Débarrassez-vous des piles usagers en respectant les instructions du
fabricant.
Notas para el manejo de las baterías de litio:
PRECAUCIÓN
Peligro de explosión si reemplaza incorrectamente la batería.
Reemplácela por otra igual o de tipo equivalente recomendada por el
fabricante.
Deshágase de las baterías de acuerdo con las instrucciones del
fabricante.
Note concernenti le batterie al litio:
AVVERTENZA
Se la batteria non viene sostituita in modo corretto c’è pericolo di
esplosioni.
Sostituire la batteria con una dello stesso tipo o con una equivalente
raccomandata dalla fabbrica.
Smaltire le batterie usate seguendo le istruzioni della fabbrica.
Observera om hantering av litiumbatterier:
OBSERVERA!
Felaktigt batteribyte medför risk för explosion.
Byt endast ut batteriet mot ett batteri av samma eller motsvarande typ
rekommenderat av tillverkaren.
Kassera ett förbrukat batteri enligt tillverkarens anvisningar.
Opmerkingen betreffende de behandeling van lithiumbatterijen:
LET OP
Ontploffingsgevaar indien de batterij verkeerd wordt aangebracht.
Vervang uitsluitend door een batterij van hetzelfde of een gelijkwaardig
type, aanbevolen door de fabrikant.
Gooi gebruikte batterijen weg overeenkomstig de instructies van de
fabrikant.
Notas para o manuseio de pilhas de lítio:
PRECAUÇÃO
Existe o perigo de explosão se a pilha for trocada incorretamente.
Troque apenas com o mesmo tipo ou equivalente recomendado pelo
fabricante.
Descarte-se das pilhas usadas de acordo com as instruções do
fabricante.
Huomautuksia litiumparistojen käsittelystä:
HUOMAUTUS
Räjähdysvaara, jos paristo vaihdetaan väärin.
Paristo tulee vaihtaa vain samaniaiseen tai valmistajan suosittelemaan
vastaavaan tyyppiin.
Hävitä käytetyt paristot valmistajan antamien ohjeiden mukaisesti.
EL-1750PIII(LCO)-Semko 04.9.1, 9:28 AM2

2
CONTENTS
ENGLISH
Page
• USING THE CALCULATOR FOR THE
FIRST TIME ........................................................... 3
• OPERATING CONTROLS ..................................... 4
• INK ROLLER REPLACEMENT ............................. 8
• PAPER ROLL REPLACEMENT ............................. 9
• BATTERY REPLACEMENT ................................. 10
• HOW TO CONNECT THE AC ADAPTOR
(OPTION) ............................................................. 11
• ERRORS .............................................................. 12
• REPLACEMENT OF BATTERY FOR
MEMORY PROTECTION .................................... 12
• SPECIFICATIONS ............................................... 14
• RESETTING THE UNIT ....................................... 15
• CALCULATION EXAMPLES .............................. 135
To insure trouble-free operation of your SHARP
calculator, we recommend the following:
1. The calculator should be kept in areas free from
extreme temperature changes, moisture, and dust.
2. A soft, dry cloth should be used to clean the
calculator. Do not use solvents or a wet cloth.
3. Since this product is not waterproof, do not use it or
store it where fluids, for example water, can splash
onto it. Raindrops, water spray, juice, coffee,
steam, perspiration, etc. will also cause malfunction.
4. If service should be required, use only a SHARP
servicing dealer, a SHARP approved service facility
or SHARP repair service.
SHARP will not be liable nor responsible for any
incidental or consequential economic or property
damage caused by misuse and/or malfunctions of
this product and its peripherals, unless such
liability is acknowledged by law.
OPERATIONAL NOTES
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM2

3
USING THE CALCULATOR FOR THE FIRST TIME
First, pull out the insulation sheet for the memory
protection battery (installed for retaining the date/
time/tax rate information). Reset the calculator to
initialize the unit's state, then adjust the date and
time before using the calculator.
Removing the insulation sheet, and resetting
1. Pull out the insulation sheet for the memory
protection battery.
2. Press the RESET switch located on the back of the
unit.
(See “RESETTING THE UNIT”.)
* The clock starts from 00:00:00 a.m. on 1 January
2005.
Adjusting date and time
Example: In the case of 3:38 p.m. on 15 September
2004
* When the adjustment is complete, the clock starts at
3:38:00 p.m.
15 9 2004 15. 09. 2004
15 38 15-38 00
0.
(see “GRAND TOTAL / RATE SETTING MODE
SELECTOR”)
Operation Display
GT • RATE
SET
EL-1750PIII(LCO)-Eng 04.9.16, 11:11 AM3

4
OFF •P P•IC ON
POWER SWITCH; PRINT / ITEM
COUNT MODE SELECTOR:
“OFF”: Power OFF
“•”: Power ON. Set to the non print mode.
“P”: Power ON. Set to the print mode.
“P•IC”: Power ON. Set to the print and item count
mode.
1) For addition or subtraction, each time
is pressed, 1 is added to the item
counter, and each time is pressed, 1
is subtracted.
•The count is printed when the calcu-
lated result is obtained.
•Pressing of , clears the
counter.
2) When the grand total/rate setting mode
selector is in the ON position (GT), the
counter will count the number of times
that the calculation results have been
stored in the grand total memory. To print
and clear the count, press the key.
3) The memory item counter will count the
number of times that the key has
been pressed in the addition.
OPERATING CONTROLS Note: •Each time the key is used in
the subtraction, 1 will be subtracted
from the count.
•The count is printed when the
memory is recalled.
•Pressing of the key clears the
counter.
Note: The counter has a maximum capacity of 3
digits (up to ±999). If the count exceeds the
maximum, the counter will recount from zero.
ROUNDING SELECTOR:
Example: Set Decimal Selector to 2.
4 ÷9 = 0.444 ... , 5 ÷9 = 0.555 ...
Note: The decimal point floats during successive
calculation by the use of or .
If the decimal selector is set to “F”then the answer is
always rounded down ( ).
4 9 5 9
0.45 0.56
5/4 0.44 0.56
0.44 0.55
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM4

5
GT • RATE
SET
GRAND TOTAL / RATE SETTING MODE
SELECTOR:
“GT”: Grand Total
“•”: Neutral
“RATE SET”: To set the date, time, and tax rate, set
this switch at the “RATE SET”
position.
Date:
•Enter in the order of day, month, and year, then
press to complete the entry.
•Use to separate day, month, and year.
•When is pressed, the number entered is
evaluated and displayed as “date”if the value is
within the following range; “Error”is displayed
otherwise, and the previously set date is restored.
Day: 1 - 31; Month: 1 - 12; Year: 2000 - 2099 (in 4
digits) or 00 - 99 (in 2 digits)
Time:
•Enter in the order of hour, minutes, then press
to complete the entry.
(There is no entry available for the seconds value.
The clock starts at zero second.)
•If the hour/minute digit is less than 10, it is not
necessary to enter the first digit “0”.
•Use to separate hour and minute values.
•When is pressed, the number entered is
evaluated and displayed as “time”if the value is
within the following range; “Error”is displayed
otherwise, and the previously set time is restored.
Hour: 0 - 23 (24-hour system for the hour entry),
Minute: 0 - 59
Tax rate:
•Press three times, enter the tax rate, followed
by .
•A maximum of 4 digits can be stored (decimal point
is not counted as a digit).
•Only one rate can be stored. If you enter a new rate,
the previous rate will be cleared.
F20A
3
DECIMAL / ADD MODE SELECTOR:
“3 2 0”: Presets the number of decimal places in the
answer.
“F”: The answer is displayed in the floating decimal
system.
“A”: The decimal point in addition and subtraction
entries is automatically positioned to the 2nd
digit from the lowest digit of entry number. Use
of the add mode permits addition and subtrac-
tion of numbers without entry of the decimal
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM5

6
point. Use of , and will automatically
override the add mode and decimally correct
answers will be printed.
CLOCK / CALENDAR KEY:
•Each time this key is pressed, the mode
switches.
Calculation mode →Date display mode →
Clock display mode →Calculation mode
•Use this key also to adjust date and time
(see “GRAND TOTAL / RATE SETTING
MODE SELECTOR”).
PAPER FEED KEY
LAST DIGIT CORRECTION KEY
NON-ADD / SUBTOTAL KEY:
Non-add –When this key is pressed right after
an entry of a number in the Print mode, the
entry is printed on the left-hand side with the
symbol “#”. This key is used to print out
numbers not subjects to calculation such as
code, date, etc.
Subtotal –Used to get subtotal(s) of additions
and/or subtractions. When pressed following
the or key, the subtotal is printed with
the symbol “
◊ ”and the calculation may be
continued.
By pressing this key even in the Non-print
mode, the displayed number is printed
without any symbol.
•When the POWER SWITCH; PRINT / ITEM
COUNT MODE SELECTOR is set “•”, “P”or
“P•IC”position, and Date or Clock is
displayed, press this key to print the
displayed contents, including “#”symbol,
from the left side of the paper roll.
Example:
Date printing
#15 •09 •2004 ••••••
(In the case of 15 September 2004)
Clock printing
#10 •30 •••••••••••
(when the time is 10:30 a.m.)
#18 •25 •••••••••••
(when the time is 6:25 p.m.)
•When the Date / Clock printing is complete,
the Calculation mode is restored.
CLEAR / CLEAR ENTRY KEY
Press this key twice, followed by , to print
the set tax rate.
TOTAL KEY
EQUAL KEY
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM6

7
CHANGE SIGN KEY:
Changes the algebraic sign of a number (i.e.,
positive to negative or negative to positive).
RECALL AND CLEAR MEMORY KEY
RECALL MEMORY KEY
TAX-INCLUDING KEY
PRE-TAX KEY
AVERAGE KEY:
Used to calculate the average.
GRAND TOTAL KEY
COST PRICE ENTRY KEY:
Press this key to enter the cost price.
SELLING PRICE ENTRY KEY:
Press this key to enter the selling price.
MARGIN ENTRY KEY:
Press this key to enter the margin.
DISPLAY SYMBOLS:
M:Appears when a number is in the memory.
–:Appears when a number is negative.
G:Appears when a number is in the grand total
memory.
E:Appears when an overflow or other error is
detected.
TAX+ : Appears when the total calculated includes
tax.
TAX– : Appears when the total calculated excludes
tax.
TAX : Appears when the tax rate is set.
* Although all available symbols are shown here for
instruction purposes, these symbols will not appear
on the screen simultaneously.
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM7

8
INK ROLLER REPLACEMENT
If printing is blurry even when the ink roller is in the
proper position, replace the roller.
Ink roller: Type EA-772R
WARNING
APPLYING INK TO WORN INK ROLLER OR USE
OF UNAPPROVED INK ROLLER MAY CAUSE
SERIOUS DAMAGE TO PRINTER.
1) Set the power switch to OFF.
2) Remove the printer cover. (Fig. 1)
3) Hold the top of the ink roller and remove the roller
by pulling it toward you and then upward. (Fig. 2)
4) Install the new ink roller in the correct position.
Make sure that the roller is securely in place. (Fig.
3)
5) Put back the printer cover.
Cleaning the printing mechanism
If the print becomes dull after long time usage,
clean the printing wheel according to the
following procedures:
1) Remove the printer cover and the ink roller.
2) Install the paper roll and feed it until it comes out of
the front of the printing mechanism.
3) Put a small brush (like a tooth brush) lightly to the
printing wheel and clean it by pressing .
4) Put back the ink roller and the printer cover.
Note: •Do not rotate the printing mechanism manu-
ally, this may damage the printer.
Fig. 1
Fig. 2 Fig. 3
EL-1750PIII(LCO)-Eng 04.9.15, 3:27 PM8