●The battery is run down.
●Nothing is recorded.
●No copy can be made because of
the SCMS copyright system.
●A track cannot be edited.
●
Recording cannot be performed cor-
rectlyduetovibrationorshockintheunit.
●Editing is impossible.
●The disc is scratched.
●Poor connection of the digital cable.
●The disc is out of recording space.
●The unit is in the hold mode.
●The OPEN lever was moved during
recording or editing.
●A disc has not been loaded.
●You tried to record on a playback-
only disc.
●Improper power is being supplied.
●The MD is write protected.
●The disc is damaged.
●Since a track number is currently
being located or written to, the unit
cannot accept your command.
●You have come to the conclusion
that the unit is out of order.
●The temperature is too high.
●A large portion of the disc has been
damaged.
●There is no space left for recording
character information (track names,
disc names, etc.).
●The track has been protected from
being erased.
●A large portion of the disc has been
damaged.
●Thereis an error inthe recorded sig-
nal.
●Adiscwhichcontainsdataotherthan
music was played.
●There is an error in the signal from
the disc.
●Charge the rechargeable battery or
replacethe alkaline batteries (oruse
the AC adaptor for power).
●Replace the disc with a recorded disc.
●Record using the analog cable.
●Changethestop position of the track
and then try editing it.
●Re-record or replace it with another
recordable disc.
●Check the number of tracks.
●If the sound you hear is not right, try
recording again.
●Replace the disc with another re-
cordable disc.
●Connect the digital cable securely.
●Replace it with another recordable
disc.
●Return the HOLD switch to its origi-
nal position.
●Turn off the power and remove the
MiniDisc.
●Load a disc.
●Replace it with a recordable disc.
●Use one of the specified power
sources.
●Movethe write protectionknob back
to its original position.
●Reload the disc or replace it.
●Replaceitwithanotherrecorded disc.
●Wait for a while and try the opera-
tion again.
●Tohave it repaired, go to the distribu-
tor where you purchased the unit.
●Turn off the power, and wait for a
while.
●Replace it with another recorded
disc.
●Replace it with another recordable
disc.
●Edit the track with the device on
which it was recorded.
●Replace it with another recorded
disc.
●Erase all of the signal errors, and
then try recording again.
●A disc which contains non-music
data cannot be played.
●Replace it with another recorded
disc.
ERROR MESSAGES
Error messages Remedy
BATT EMPTY
BLANK DISC
Can’t COPY
Can’t EDIT
Can’t REC
Can’t WRITE
DEFECT
Din UNLOCK
READ ERROR
DISC FULL
HOLD
LOCKED
LOCK ERROR
NO DISC
PB DISC
POWER ?
SORRY
SYSTEM ERR
TEMP OVER
TOC ERROR
TOC FULL
Tr. Protect
U TOC ERROR
? DISC
Meaning
PROTECTED
Whenthe number of tracksused reaches
the limit, regardless of the remaining re-
cording time, further recording will be
impossible.
(Maximum number of tracks: 255)
If a MiniDisc has been recorded or ed-
ited repeatedly or if a MiniDisc has
scratches on it, it may not be possible to
recordthe maximum number of tracks on
it.
If there are scratches on a disc, the unit
willautomaticallyavoidrecording in those
areas.The recording time will be reduced.
When the remaining recording time of a
disc is displayed, short tracks less than
12 seconds long may not be included in
the total.
For MiniDiscs on which repeated record-
ing and editing operations were per-
formed, the COMBINE function may not
work.
A cluster (about 2 seconds) is normally the
minimumunitofrecording.So,evenifatrack
is less than 2 seconds long, it will use about
2 seconds of space on the disc.
Therefore, the time actually available for re-
cordingmaybelessthantheremainingtime
displayed.
If there are scratches on discs, those sec-
tionswillbeautomaticallyavoided(norecord-
ing will be placed in those sections). There-
fore, the recording time will be reduced.
For MiniDiscs on which repeated record-
ing and editing were performed, some
soundsmay be skipped while cueing and
reviewing.
If there are scratches or dust on a
MiniDisc,thetracknumbersfollowing that
track will be increased by one.
MINIDISC SYSTEM LIMITATIONS
MiniDiscs are recorded using a different system than is used for cassette tapes or DAT
recordings. Therefore, the following conditions may be encountered, depending on how
the disc has been recorded or edited. These are due to system limitations, and should be
considered normal.
Even if the maximum recording
time of a MiniDisc has not been
reached, “DISC FULL” or “TOC
FULL” may be displayed.
Even if the number of tracks and
the recording time have not
reached the limit, “DISC FULL”
may be displayed.
Even if several short tracks are
erased, the remaining recording
time may not show an increase.
Two tracks may not be combined
in editing.
The total of the recorded time and
time remaining on a disc may not
add up to the maximum possible
recording time.
When recorded tracks are played
back using the cue and review op-
erations, some sounds may be
skipped.
A track number can be created in
the middle of a track.
