– 8 –
MD-MT866H/MD-MT866W
Error Messages
ERROR MESSAGES
BATT EMPTY
(LoBATT)
BLANK MD
(BLANK)
Can’t COPY
(Can’tC)
Can’t EDIT
(Can’tE)
Can’t READ *
(Can’tS)
(Can’tT)
(Can’tU)
Can’t REC
(Can’tR)
Can’t STAMP
Can’t WRITE
(Can’tW)
CHARGEmode
DEFECT
(DEFECT)
DISC FULL
Er-MD **
(ErMD*)
HOLD
(HOLD)
LOCKED
(Can’tLOCK)
MEANING
●The battery is run down.
●Nothing is recorded.
●You tried to record from a copy prohib-
ited MiniDisc.
●A track cannot be edited.
●Thedisc data cannotberead because the
disc is damaged.
●Recording cannot be performed correctly
due to vibration or shock.
●Stamp function does not work.
●CannotsavetheTOCinformationcorrectly
to a MiniDisc. (A large portion of the disc
has been damaged.)
●The Charge/Operation switch is not set to
the operation mode when using this unit
with the AC adaptor.
●The disc is scratched.
●The disc is out of recording space.
●The microprocessor has reported a sys-
tem fault and the unit is out of order.
●The unit is in the hold mode.
●You removed a MiniDisc whilst recording
or editing.
REMEDY
●Charge the rechargeable battery or replace the alkaline battery
(or use the AC adaptor for power).
●Replace the disc with a recorded disc.
●Record using the analogue cable.
●Change the stop position of the track and then edit it.
●Reload the disc.
●Replace it with another recorded disc.
●Re-record or replace it with another recordable disc.
●Check the number of tracks.
●Replace the disc with another recordable disc.
●Set the Charge/Operation switch to the operation mode.
●If the sound you hear is not right, record again.
●Replace the disc with another recordable disc.
●Replace it with another recordable disc.
●To have it repaired, go to the distributor where you purchased the
unit.
●Return the HOLD switch to its original position.
●Turn off the power and remove the MiniDisc.
ERROR MESSAGES
NO DISC
NO SIGNAL
(noSIG.)
PLAY MD
(PLAYmd)
POWER ?
PROTECTED
SORRY
(SORRY)
TEMP OVER
(TEMP!)
TOC FORM **
(Tform**)
TOC FULL
Tr. Protect
? DISC
(? DISC)
MEANING
●A disc has not been loaded.
●Poor connection of the digital cable.
●No output signal comes out from the con-
nected unit to playback.
●The input signal has improper sampling
frequency.
●You recorded on a playback-only disc.
●The battery charger is defective.
●
The write protection tab of a MiniDisc is
set to the protected position.
●
You triedtorecordon a playback-only disc.
●Since a track number is currently being
locatedorupdated, the unit cannot accept
your command.
●The temperature is too high.
●There is an error in the recording
signal.
●There is no space left for recording char-
acter information (track names, disc
names, etc.).
●The track has been protected from being
erased.
●A disc which contains data other than
music was played.
●There is an error in the signal recorded
on the disc.
●Stamping is not possible.
REMEDY
●Load a disc.
●Connect the digital cable securely.
●If the portable CD player has a function to prevent sound skips, deacti-
vate it.
●Playback with the connected unit.
●Replace it with a recordable disc.
●To have it repaired, go to the distributor where you purchased
the unit.
●
Move the write protection tab back to its original position.
●Replace it with a recordable MiniDisc.
●Wait for a while and try the operation again.
●Turn off the power, and wait for a while.
●Erase all of the tracks, and then record again.
●Replace it with another recordable disc.
●Edit the track with the device on which it was recorded.
●A disc which contains non-music data cannot be played.
●Replace it with another recorded disc.
●Retry.
( ): Error messages seen on the remote control.
Number or symbol appears in * position.
