Sharper Image 205234 User manual

Thank you for purchasing the Sharper Image Heated Fog-Free Shower Mirror. Please read these
instructions prior to using this device for the first time. In addition, please store this guide for
future reference.
- 1 -
Item No. 205234
User Guide
HEATED FOG-FREE SHOWER MIRROR

- 2 -
FEATURES
• Heated glass
• Fog proof
• 1X & 3X magnification
• Stainless steel flex arm
• Chrome finish
• 6.5” dual-sided swivel mirror
• Adjustable razor hanger
• For men and women
PRODUCT PART IDENTIFICATION
HOW THE HEATED FOG-FREE SHOWER
MIRROR WORKS
When installed properly, a small amount
of water from your shower will circulate
through a copper coil embedded in the
shower mirror. As the water circulates
it warms the mirrors to the same
temperature as the shower water, making
it impossible for fog to form. The water
completes its circuit by traveling back up
through the flexible arm and out into the
shower stream.
HOW TO INSTALL THE HEATED FOG-
FREE SHOWER MIRROR
1. Remove showerhead from shower
wall pipe. Turn showerhead connector
counter clockwise.
Note: Pliers may be required to loosen
the showerhead. If pliers are needed,
place a soft cloth between the pliers
and the showerhead connector to
prevent damaging the showerhead
connector surface.
2. Seal shower pipe threads. Apply several
turns of plumbing tape (not included) to
seal shower pipe threads.
Note: If this connection seems loose or
leaks after installing the shower mirror,
apply more tape to the connection.
3. Align plumbing connection. Carefully
align mirror plumbing connector with
the thread shower pipe.
4. Connect mirror. Rotate entire mirror
around shower wall pipe. The mirror
will rotate easily only if the plumbing
connector and shower wall pipe are
properly aligned.
Note: If the mirror tightens down and
comes to a final position that is not
desired, the addition of more plumbing
tape to the shower pipe threads will
influence the final, tightened down
position of the mirror.
5. Connect showerhead. Replace the
showerhead by screwing the showerhead
connector onto the threaded shower
mirror fitting.

- 3 -
Note: If pliers are needed to tighten the
showerhead, place a soft cloth between
the pliers and the showerhead connector
to prevent marring. Plumbing tape
should be applied to the threads of this
connection to keep from leaking.
6. Spin mirror to select side. Select the 1X
or 3X magnified mirror side by spinning
the mirror frame.
Note: The mirror frame will NOT spin
endlessly. The mirror frame will spin
360-degress and then stop. Reverse the
spin of the mirror to select opposite side.
7. Assemble razor hanger. Insert razor
hanger into one of the frame slot hole
on either side of the mirror—as shown.
Slide razor hanger in frame slot so that it
comes to rest at the bottom of the mirror.
CLEANING INSTRUCTIONS
• Keep water droplets from spotting the
surface by wiping the mirror and frame
dry with a soft towel after each use.
• Clean with only nonabrasive, liquid glass
cleaner and a soft cloth.
• Never use abrasive cleaners as they
will scratch the mirror glass and frame
surface.
• With any cleaner, it is always a good idea
to test a small area before cleaning entire
surface.
• Do not use paper towels to clean with—
they can be abrasive and leave scratches
in the chrome surface. Use only a soft,
clean towel or cloth.
WARNING
Do not use paper towels to clean with—they
can be abrasive and leave scratches in the
chrome surface. Use only a soft, clean towel
or cloth.
WARRANTY / CUSTOMER SERVICE
Sharper Image branded items purchased
from SharperImage.com include a
1-year limited replacement warranty.
If you have any questions not covered
in this guide, please call our Customer
Service department at 1 [phone].
Customer Service agents are available
Monday through Friday, 9:00 a.m. to 6:00
p.m. ET.
The SHARPER IMAGE® name and logo are registered trademarks.
©Sharper Image. All Rights Reserved.