shars 101-1008 User manual

Operating manual
Version 17.10.12
Grinding machine for Endmills and Drill bits
101-1008

Version 1.0.4 dated 2014-09-19Page 2 Original operating instructions
Table of contents
1 Safety
1.1 Representation Conventions ....................................................................................................................5
1.2 Safety instructions (warning notes)...........................................................................................................6
1.2.1 Classification of hazards...........................................................................................................................6
1.2.2 Other pictograms......................................................................................................................................7
1.3 Intended use.............................................................................................................................................7
1.4 Possible dangers caused by the grinding machine for burins ..................................................................8
1.5 Qualification of personnel.........................................................................................................................8
1.5.1 Target group.............................................................................................................................................8
1.5.2 Authorized personnel................................................................................................................................9
1.6 Operators positions...................................................................................................................................9
1.7 Safety measures during operation..........................................................................................................10
1.8 Safety devices ........................................................................................................................................10
1.9 Safety check...........................................................................................................................................10
1.9.1 ON / Off - Switch.....................................................................................................................................12
1.9.2 Spark protection......................................................................................................................................12
1.10 Personal protective equipment for special works ...................................................................................12
1.11 Safety during operation...........................................................................................................................12
1.12 Accident report........................................................................................................................................13
1.13 Electrical system.....................................................................................................................................13
2 Technical data
2.1 Electrical connection...............................................................................................................................14
2.2 Speed .....................................................................................................................................................14
2.3 Adjustable angle.....................................................................................................................................14
2.4 Travels....................................................................................................................................................14
2.5 Grinding wheels......................................................................................................................................14
2.6 Grinding devices.....................................................................................................................................14
2.7 Collet seat...............................................................................................................................................14
2.8 Dimensions.............................................................................................................................................14
2.9 Environmental conditions........................................................................................................................14
2.10 Emissions ...............................................................................................................................................15
2.11 Dimensions cup wheel............................................................................................................................16
3 Assembly
3.1 Scope of delivery....................................................................................................................................17
3.2 Storage...................................................................................................................................................18
3.3 Installation and assembly .......................................................................................................................19
3.3.1 Requirements regarding the installation site...........................................................................................19
3.3.2 Electrical connection...............................................................................................................................19
3.3.3 Assembly................................................................................................................................................19
3.4 First commissioning................................................................................................................................20
4Operation
4.1 Safety......................................................................................................................................................21
4.2 Assembly and function............................................................................................................................23
4.3 Handling the tool holder..........................................................................................................................24
4.4 Setting the shaft shoulder.......................................................................................................................25
4.5 Grinding angles.......................................................................................................................................26
4.6 Assembling the devices..........................................................................................................................27
4.6.1 Grinding device for drill bit......................................................................................................................27
4.6.2 Grinding device turning tool....................................................................................................................28
4.6.3 Grinding device end mill .........................................................................................................................29

Version 1.0.4 dated 2014-09-19 Page 3Original operating instructions
5 Maintenance
5.1 Safety ..................................................................................................................................................... 30
5.1.1 Preparation............................................................................................................................................. 30
5.1.2 Restarting ............................................................................................................................................... 30
5.2 Inspection and maintenance .................................................................................................................. 31
5.2.1 Exchange of the abrasive wheel ............................................................................................................ 31
5.3 Repair..................................................................................................................................................... 31
6 Ersatzteile - Spare parts
6.1 Ersatzteilzeichnung - Drawing spare parts ............................................................................................33
6.1.1 Ersatzteilliste - Spare part list ............................... ................................................................................. 34
6.2 Accessories ........................................................................................................................................... 36
6.2.1 Spare part list accessories .................................................................................................................... 37
6.4 Schaltplan - Wiring diagram 230V.......................................................................................................... 39
7 Annex
7.1 Copyright ................................................................................................................................................ 40
7.2 Terminology/Glossary ............................................................................................................................ 40
7.3 Change information manual ................................................................................................................... 40
7.4 Product follow-up.................................................................................................................................... 40
7.5 Liability claims for defects / warranty...................................................................................................... 41
7.6 Advice for disposal / Options of re-use................................................................................................... 41
7.6.1 Decommissioning................................................................................................................................... 42
7.6.2 Disposal of the packaging of the new machine ...................................................................................... 42
7.6.3 Disposal of the used machine................................................................................................................ 42
7.6.4 Disposal of electrical and electronic components .................................................................................. 42
7.7 Disposal via municipal collecting points ................................................................................................. 43

Thank you very much for purchasing a product made by SHARS Machine.
dealer or directly the company SHARS.
SHARS metal working machines offer a maximum of
Version 1.0.4 dated 2014-09-19Page 4 Original operating instructions
Preface
Dear customer,
quality, technically optimum solutions and convince
by an outstanding price performance ratio. Continuous enhancements and product innovations guarantee
state-of-the-art products and safety at any time.
Before commissioning the machine please thoroughly read these operating instructions and get familiar with
the machine. Please also make sure that all persons operating the machine have read and understood the
operating instructions beforehand.
Keep these operating instructions in a safe place nearby the machine.
Information
The operating instructions include indications for safety-relevant and proper installation, operation and main-
tenance of the machine. The continuous observance of all notes included in this manual guarantee the safety
of persons and of the machine.
The manual determines the intended use of the machine and includes all necessary information for its eco-
nomic operation as well as its long service life.
In the paragraph "Maintenance" all maintenance works and functional tests are described which the operator
must perform in regular intervals.
The illustration and information included in the present manual can possibly deviate from the current state of
construction of your machine. Being the manufacturer we are continuously seeking for improvements and
renewal of the products. Therefore, changes might be performed without prior notice. The illustrations of the
machine may be different from the illustrations in these instructions with regard to a few details. However,
this does not have any influence on the operability of the machine.
Therefore, no claims may be derived from the indications and descriptions. Changes and errors are reserved!
Your suggestion with regard to these operating instructions are an important contribution to optimising our
work which we offer to our customers. For any questions or suggestions for improvement, please do not hesi-
tate to contact our service department.
If you have any further questions after reading these operating instructions and you are not able to
solve your problem with a help of these operating instructions, please contact your specialised

Version 1.0.4 dated 2014-09-19 Page 5Original operating instructions
1 Safety
1.1 Representation Conventions
gives additional advices
calls on you to act
enumerations
This part of the operating instructions
explains the meaning and use of the warning notices included in these operating instructions,
defines the intended use of the grinding machine for burins,
points out the dangers that might arise for you or others if these instructions are not observed,
informs you about how to avoid dangers.
In addition to these operation instructions, please observe
the applicable laws and regulations,
the legal regulations for accident prevention.
When installing, operating, maintaining and repairing the grinding machine for burins it is nec-
essary to observe the European standards
The still applicable country-specific regulations need to be applied for the not yet for the corre-
sponding national country law implemented German standards.
If required it is necessary to take the corresponding measures to comply with the country-spe-
cific regulations before commissioning the grinding machine for burins.
Please keep this documentation always close to the grinding machine for burins.

Version 1.0.4 dated 2014-09-19Page 6 Original operating instructions
1.2 Safety instructions (warning notes)
1.2.1 Classification of hazards
We classify the safety instructions into different levels. The table below gives an overview of the
classification of symbols (pictograms) and signal words for the specific danger and its (possible)
consequences.
Pictogram Signal word Definition/Consequences
DANGER! Imminent danger that will cause severe injury of death to the staff.
WARNING! A danger that might cause severe injury to the staff or can lead to death.
CAUTION! Danger of unsafe procedure that might cause injury to the staff or property
damages.
ATTENTION!
Situation that could cause damage to the machine and products and other
types of damage.
No risk of injury to the staff.
INFORMATION
Application tips and other important or useful information and notes.
No dangerous or harmful consequences for the staff or objects.
In case of specific dangers, we replace the pictogram by
or
general danger by a warning of injury of hands, hazardous
electrical voltage, rotating parts.

technical or procedural changes which had not been performed by the company SHARS
out the approval of the company SHARS Ma
Version 1.0.4 dated 2014-09-19 Page 7Original operating instructions
1.2.2 Other pictograms
1.3 Intended use
Use
The grinding machine for burins is designed and manufactured to be used in a non-explosive
environment. The grinding machine for burins must only be used to manufacture single edge
milling cutters, stamps and to regrind tools, cutting tools such as end milling cutters, drills, TIG
welding electrodes, etc.
The machine
is no longer
used as pre-
scribed!
If the grinding machine for burins is used in any way other than described above, modified with-
schinen Germany GmbH or used in any other
way then the grinding machine for burins is being used improperly.
We do not take any liability for damages caused by improper use.
We expressly point out that the guarantee or CE conformity will expire due to any constructive
Maschinen Germany GmbH.
It is also part of intended use that you
observe the operating values and setting of the data grinding machine for burins,
observe the operating instructions,
observe the inspection and maintenance instructions.
 "Technical data“ on page 14
Warning of flammable sub-
stances! Disconnect the mains plug!
Activation forbidden! Use protective glasses!
Use protective boots! Contact address
Protect the environment!

Version 1.0.4 dated 2014-09-19Page 8 Original operating instructions
1.4 Possible dangers caused by the grinding machine for burins
The grinding machine for burins is state-of-the-art.
Nevertheless, there is a residual risk as the grinding machine for burins operates with
at high speeds,
rotating parts,
with an abrasive wheel (flying sparks)
with electrical voltages and currents.
We have used construction resources and safety techniques to minimize the health risk for the
staff resulting from these hazards.
If the grinding machine for burins is used and maintained by the staff who are not duly qualified,
there may be a risk resulting from incorrect or unsuitable maintenance of the grinding machine
for burins.
INFORMATION
All staff involved in assembly, commissioning, operation and maintenance, must
be duly qualified,
strictly follow these operating instructions.
In the event of intended use
there may be a risk to the persons,
there may be a risk to the grinding machine for burins and other material values,
the correct function of the grinding machine for burins may be affected.
Always disconnect the mains plug from the socket before performing any cleaning or mainte-
nance works.
1.5 Qualification of personnel
1.5.1 Target group
This manual is addressed to
the operating companies,
the operators,
the staff for maintenance works.
Therefore, the warning notes refer to both, operation and maintenance staff of the grinding
machine for burins.
Determine clearly and explicitly who will be responsible for the different activities on the
machine (operation, maintenance and repair).
Unclear responsibilities constitute a safety risk!
The qualifications of the staff for the different tasks are mentioned below:
Operator
The operator is instructed by the operating company about the assigned tasks and possible
risks in case of improper behaviour. Any tasks which need to be performed beyond the opera-
tion in the standard mode must only be performed by the operator if it is indicated in these
instructions and if the operating company expressively commissioned the operator.
Electrical specialist
Due to his professional training, knowledge and experience as well as his knowledge of respec-
tive standards and regulations the electrical specialist is able to perform works on the electrical
system and to recognise and avoid any possible dangers himself.

Version 1.0.4 dated 2014-09-19 Page 9Original operating instructions
The electrical specialist is specially trained for the working environment in which he is working
and knows the relevant standards and regulations.
Specialist staff
Due to its professional training, knowledge and experience as well as his knowledge of rele-
vant regulations the specialist staff is able to perform the assigned tasks and to recognise and
avoid any possible dangers himself.
Instructed persons
Instructed persons were instructed by the operating company about the assigned tasks and any
possible risks in case of improper behaviour.
1.5.2 Authorized personnel
WARNING!
Incorrect use and maintenance of the grinding machine for burins constitutes a danger
for the staff, objects and the environment.
Only authorized staff may operate the grinding machine for burins and tools!
Persons authorized to operate and maintain should be trained technical personnel and
instructed by the ones who are working for the operating company and for the manufacturer.
The operating company must
Obligations of
the
of the operat-
ing company,
train the personnel,
instruct the personnel in regular intervals (at least once a year) on
- all safety standards that apply to the machine,
- the operation,
- accredited technical guidelines,
check personnel‘s state of knowledge,
document the trainings/instructions,
require personnel to confirm participation in training/instructions by means of a signature,
check whether the personnel is working safety- and risk-conscious and observe the operat-
ing instructions.
The operator must
Obligations of
the
operator
have followed a training on the operation of the grinding machine for burins,
know the function and performance,
before taking the machine in operation
- have read and understood the operating instructions,
- be familiar with all safety devices and instructions.
Additional
requirements
regarding the
qualification
For work on the following parts there are additional requirements:
Electrical parts or operating agents: shall only be performed by an electrician or under the
guidance and supervision of an electrician.
Before starting work on electrical parts or operating agents, following measures are to be
performed in the following order.
Disconnect all poles.
Secure against switching on.
Check if the machine is zero potential.
1.6 Operators positions
The operator’s position is in front of the grinding machine for burins.

Version 1.0.4 dated 2014-09-19Page 10 Original operating instructions
INFORMATION
The mains plug of the grinding machine for burins must be freely accessible.
1.7 Safety measures during operation
CAUTION!
Risk by inhaling health hazardous dusts and fogs.
Depending on the materials which need to be treated and the agents which are used,
dusts and fogs may be generated which endanger your health.
Make sure that the generated health hazardous dusts and fogs are safely sucked-off at
the place of origin and that they are dissipated or filtered. To do so, use a suitable
extraction unit.
CAUTION!
Risk of fire and explosion by using inflammable materials or cooling-lubricating agents.
Before processing inflammable materials (e.g. aluminium, magnesium) or using
inflammable auxiliary materials (e.g. spirit) it is necessary to take additional preventive
measures in order to safely avoid health risks.
1.8 Safety devices
Use the grinding machine for burins only with properly functioning safety devices.
Stop the grinding machine for burins immediately if there is a failure on the safety device or if it
is not functioning for any reason. It is your responsibility!
If a safety device has been activated the grinding machine for burins must only be used if you
have removed the cause of the failure,
have verified that there is no danger resulting for the staff or objects.
WARNING!
If you bypass, remove or deactivate a safety device in any other way, you are
endangering yourself and other staff working with the grinding machine for burins and
tools.
The possible consequences are:
extremely serious injuries by bursting of the abrasive wheel,
injury of eyes due to flying sparks,
injury of hands,
a fatal electrocution.
WARNING!
The separating protective covers which are made available and delivered together with
the machine are designed to reduce the risk of workpieces or fragments of tools or
workpieces flying off at high speed - however, this cannot be completely avoided.
Always work carefully and observe the limit values of your grinding process.
1.9 Safety check
Check the grinding machine for burins before each start-up or at least once per shift. Inform the
person responsible immediately of any damage, defect or change in operating function.
Check all safety devices
at the beginning of each shift (at continuous operation),
once a week (with the machine in operation),
after every maintenance and repair work.

Version 1.0.4 dated 2014-09-19 Page 11Original operating instructions
Check that prohibition, warning and information signs and the labels on the grinding machine
for burins
are legible (clean them, if necessary),
are complete (replace if necessary).
INFORMATION
Use the following table for organizing the checks.
General check
Equipment Check OK
Protective covers Mounted, firmly bolted and not damaged
Signs,
Markings Installed and legible
Date: Checked by (signature):
Functional test
Equipment Check OK
Emergency stop
push button After pressing the EMERGENCY STOP impact switch or the
pressure switch OFF the grinding machine for burins stop.
ON-OFF
switch The grinding machine for burins must only be restarted after
having disconnected and reconnected the mains plug if the
ONswitch was pressed again.
Date: Checked by (signature):

Version 1.0.4 dated 2014-09-19Page 12 Original operating instructions
1.9.1 ON / Off - Switch
The switch is provided with an
emergency stop function.
Open the cap of the switch in
order to switch on the grinding
machine for burins.
Img.1-1: ON / Off - Switch
CAUTION!
After actuating the EMERGENCY-STOP button or the ON / OFF switch, the grinding
machine for burins coasts for about 30 seconds.
1.9.2 Spark protection
The protective cover of the abrasive wheel reduces the number of flying sparks getting into your
eyes during machining.
Use protective glasses!
1.10 Personal protective equipment for special works
Protect your face and eyes: wear a safety helmet with facial protection when performing works
where your face and eyes are exposed to hazards.
Wear safety shoes when carrying the grinding machine for burins.
1.11 Safety during operation
We specially point out the specific dangers when working with and on the grinding machine for
burins and tools.
WARNING!
Before switching on the grinding machine for burins, make sure that there are
no dangers generated for persons,
no objects are damaged.
WARNING!
Fire and explosion due to sparks.
Do not operate the grinding machine for burins and tools nearby combustible or
explosive material.
Avoid any risky working practices:
Make sure that nobody is endangered by your work.
Wear safety goggles.
The instructions mentioned in these operating instructions have to be strictly observed dur-
ing assembly, operation, maintenance and repair.
Do not work on the grinding machine for burins, if your concentration is reduced, for exam-
ple, because you are taking medication.
Observe the accident prevention regulations issued by your Employers Liability Insurance
Association or other competent supervisory authority, responsible for your company.
Cap
ON / Off - Switch

SHARS Maschinen Germany GmbH
Version 1.0.4 dated 2014-09-19 Page 13Original operating instructions
Inform the supervisor about all endangerments or errors.
1.12 Accident report
Inform your superiors and immediately in the event of
accidents, possible sources of danger and any actions which almost led to an accident (near
misses).
There are many possible causes for "near misses".
The sooner they are notified, the faster the causes can be eliminated.
INFORMATION
We highlight specific dangers when performing works on the grinding machine for burins and
tools in the description of that work.
1.13 Electrical system
 "Schaltplan - Wiring diagram 400V“ on page 38
 "Schaltplan - Wiring diagram 230V“ on page 39
Have the machine and/or the electrical equipment checked regularly, at least every six months.
Immediately eliminate all defects such as loose connections, defective wires, etc.
A second person must be present during work on live components to disconnect the power in
the event of an emergency.
Immediately disconnect the grinding machine for burins and tools if there are any anomalies in
the power supply!

Version 1.0.4 dated 2014-09-19snoitcurtsnignitarepolanigirO41egaP
2 Technical data
The following information are the dimensions and indications of weight and the manufacturer‘s
approved machine data.
2.1 Electrical connection
Motor power machine type 110V 110 V / 60Hz / 1/3HP
2.2 Speed
nim0005csiddnomaid,csidgnidnirgdeepS -1
s/m53deepsgnidnirg.xaM
Speed motor 3340 min-1
2.3 Adjustable angle
°04-0raer/lacitreV
°081-0gnidnirgrepat/latnoziroH
°25-0evitageN
°51elgnanoitatorsnoitisopgnitteS
180°
2.4 Travels
mm041redlohlootlevarT
mm81redlohlootegnartnemtsujdaeniF
mm6sixahtgnelegnartnemtsujdaeniF
mm10.0deefnielacsnoisiviD
2.5 Grinding wheels
Corundum cup wheel
Corundum cup wheel
4x2x1-1
4x5/8x1-1/4''
/4''
Diamond cup wheel 4x2x1-1/4''
2.6 Grinding devices
Single edge milling cutter Up to Ø 15/32'' (Standard scope of delivery)
Turning tool Up to 13/16 x 13/16''
Drill bit Up to Ø 1''
End mill cutter Up to Ø 1''
2.7 Collet seat
385E (5C) , DIN 6341 385E (5C) , DIN 6341
G = 26.45 x 1/24"
d = 31.75
D = 37.5
L = 89
20°
2.8 Dimensions
043]mm[thgieH
054]mm[htpeD
053]mm[htdiW
05]gk[thgiewteN
2.9 Environmental conditions
C°53-5erutarepmeT
%08-52ytidimuH

Version 1.0.4 dated 2014-09-19 Page 15Original operating instructions
2.10 Emissions
The generation of noise (emission) emitted by the grinding machine for burins is 72 dB(A).
If the grinding machine for burins is installed in an area where various machines are in opera-
tion, the noise exposure (immission) on the operator of the grinding machine for burins at the
working place may exceed 80 dB(A).
INFORMATION
This numerical value was measured on a new machine under proper operating conditions.
Depending on the age respectively on the wear of the machine it is possible that the noise
behaviour of the machine changes.
Furthermore, the factor of the noise emission is also depending on manufacturing influencing
factors, e.g. speed, material and clamping conditions.
INFORMATION
The mentioned numerical value is the emission level and not necessarily a safe working level.
Though there is a dependency between the degree of the noise emission and the degree of the
noise disturbance it is not possible to use it reliably to determine if further precaution measures
are required or not.
The following factors influence the actual degree of the noise exposure of the operator:
Characteristics of the working area, e.g. size or damping behaviour,
Other noise sources, e.g. the number of machines,
Other processes taking place in the proximity and the period of time during which the
operator is exposed to the noise.
Furthermore, it is possible that the admissible exposure level might be different from country to
country due to national regulations.
This information about the noise emission shall allow the operator of the machine to more eas-
ily evaluate the endangering and risks.
CAUTION!
Depending on the overall noise exposure and the basic limit values the machine
operators has to wear an appropriate hearing protection.
We generally recommend to use a noise protection and a hearing protection.

Version 1.0.4 dated 2014-09-19snoitcurtsnignitarepolanigirO61egaP
2.11 Dimensions cup wheel
3''
1/2''
2''
1-1/2''
4''
1-1/4''
Optional Accessories: 5C Collets 202-5205~5261 1/8~1" $6.45
Size Size Size Size Order
No.
Order
No.
Order
No.
Order
No.
11/32 202-5219
5/8 202-5222
29/32 202-5255
23/64 202-5220
41/64 202-5223
59/64 202-5256
3/8 202-5236
21/32 202-5224
15/16 202-5257
25/64 202-5237
43/64 202-5225
61/64 202-5258
1/8" 202-5205
13/32 202-5238
11/16 202-5226
31/32 202-5259
9/64 202-5206
27/64 202-5239
45/64 202-5227
63/64 202-5260
5/32 202-5207
7/16 202-5240
23/32 202-5228
1 202-5261
11/64 202-5208
29/64 202-5241
47/64 202-5229
3/16 202-5209
15/32 202-5242
3/4 202-5230
13/64 202-5210
31/64 202-5243
49/64 202-5231
7/32 202-5211
1/2 202-5244
25/32" 202-5232
15/64 202-5212
33/64 202-5245
51/64 202-5233
1/4 202-5213
17/32 202-5246
13/16 202-5234
17/64 202-5214
35/64 202-5247
53/64 202-5235
9/32 202-5215
9/16" 202-5248
27/32 202-5251
19/64 202-5216
37/64 202-5249
55/64 202-5252
5/16 202-5217
19/32 202-5250
7/8 202-5253
21/64 202-5218
39/64 202-5221
57/64 202-5254

Version 1.0.4 dated 2014-09-19 Page 17Original operating instructions
3 Assembly
3.1 Scope of delivery
When the machine is delivered, check immediately that the machine has not been damaged
during transport and that all components are included. To do so take all parts out of the packag-
ing and compare the parts with the figure below to be able to assign the individualparts.
INFORMATION
The machine 101-1008 (110V) is supplied with machine illumination.
Img.3-1: Accessories
Figure
No
Quan-
tity
Description
1 5 Collets type 385E D=28 , L = 89 ; 20°
DIN 6341 Size 1/8,1/4,3/8,1/2,5/8”
2 3 Corundum cup wheel Ø4 x 2 x Ø1-1/4” Ø4x5/8xØ1-1/4”
Diamond cup wheel Ø4 x 2 x Ø1-1/4” (mounted on the machine when delivered)
3 1 Spare round belt
4 1 Socket to mount the cup wheels
5 1 Device to regrind turning tools
6 1 Device to regrind end mills
7 1 Device to regrind twist drills
8 1 Clamping ring for the device twist drill
9 1 Clamping piece for the device twist drill
12
3
4
5
6
7
10
8
9
11
12

Consult SHARS Maschinen Germany GmbH if the machine and accessories are stored for
Version 1.0.4 dated 2014-09-19Page 18 Original operating instructions
3.2 Storage
ATTENTION!
In case of wrong and improper storage electrical and mechanical machine components
might get damaged and destroyed.
Store packed and unpacked parts only under the intended environmental conditions.
Follow the instructions and information on the transport case.
more than three months or are stored under different environmental conditions than those given
here. "Information“ on page 5
10 1 Crank to clamp the tool collet chuck
11 2 Hook wrench size 38 - 42 to reclamp the collet chuck seat
12 1 Handwheel shaft shoulder
Fragile goods
(Goods require careful handling)
Protect against moisture and humid environment
 "Environmental conditions“ on page 14
Prescribed position of the packing case
(Marking of the top surface - arrows pointing to the
top)
Maximum stacking height
Example:not stackable - do not stack a second
packing case
on top of the first one.

Version 1.0.4 dated 2014-09-19 Page 19Original operating instructions
3.3 Installation and assembly
3.3.1 Requirements regarding the installation site
INFORMATION
In order to attain good functionality and a high processing accuracy as well as a long durability
of the machine the installation site should fulfil certain criteria.
Please observe the following points:
The device must only be installed and operated in a dry and well-ventilated place.
Avoid places nearby machines generating chips or dust.
The installation site must be free from vibrations also at a distance of presses, planing ma-
chines, etc.
Any parts sticking out such as stops, handles, etc. have to be secured by measures taken by
the customer if necessary in order to avoid endangerment of persons.
Provide sufficient space for the staff preparing and operating the machine and transporting
the material.
Also consider that the machine is accessible for setting and maintenance works.
Provide for sufficient illumination (Minimum value at the working place: 300 lux).
If the illuminance is too little make sure to provide additional illumination.
INFORMATION
The mains plug of the grinding machine for burins must be freely accessible.
3.3.2 Electrical connection

"Qualification of personnel“ on page 8
Machine type 400V: Connect a CEE-400V-16A plug. We recommend you to use a CEE-
400V-16A plug with pole switch since the rotating field might change when you connect the
machine to another outlet.
Make sure to switch to the correct rotation direction. The rotation direction arrow is found on
the protective cover of the cup wheel.
3.3.3 Assembly
Turn the handwheel for the shaft shoulder into the seat thread.
Img.3-2: Handwheel shaft shoulder
12
Hand wheel

Version 1.0.4 dated 2014-09-19Page 20 Original operating instructions
Plug the clamping piece and the clamping ring on the device.
Img.3-3: Device drill bit
3.4 First commissioning
ATTENTION!
Before commissioning the machine check all screws, fixtures and the clamping lever
and tighten up the screws if necessary!
CAUTION!
The cup wheel might get damaged during transportation.
Let the grinding machine for burins and tools run in for about 15 minutes before you
start grinding.
 "Personal protective equipment for special works“ on page 12.
12
Clamping ring
Clamping
piece