Shear Magic Tuffy 3000 Professional User manual

CLIPPER SERVICE
Your clippers should be serviced on a regular basis for an
authorized service centre please contact:
Botany Bay Imports 02 9700 0800.
OPTIONAL BLADES AVAILABLE FOR YOUR
SHEAR MAGIC TUFFY 3000 PROFESSIONAL
■This clipper takes Oster®A5 Type Blade sets which includes
Shear Magic®Ceramic Blades, Shear Magic®Steel Blades.
■These Clippers also take other major competitor blades.
THE SHEAR MAGIC ONE YEAR WARRANTY
All Shear Magic clippers come with a full one year warranty from
date of purchase against any manufacturing fault.
As you would expect, the warranty does not cover the following:
■Normal wearing parts (lever, latch, hinge, nameplate, bearings,
blade etc)
■Repairs or disassembly attempted by anyone other than an
authorised service centre
■Repairs made due to normal wear and tear, abuse, improper
maintenance, or dropping.
■Any alterations made to the tool.
■Damage due to blade coolants or other chemicals.
■Damage resulting from shipping or transit.
For warranty work, send proof of purchase or receipt along with
equipment to the place of purchase. Before sending, please check our
trouble shooting guide or online at www.shearmagic.net.au to ensure it is
not a common or easy to solve problem.
The product that is sent in for warranty that is over 6 months old and up
to 12 months old, warranty parts will be replaced but where the products
has done a lot of work a service charge will be applied.
Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law.
5 6
PO BOX 260 BOTANY NSW 1455 Ph: [phone]
Email: [email protected]
Website: www.shearmagic.net.au Fax: [phone]
ABN 31 128 341 980
INSTRUCTION MANUAL
Tuffy 3000 Professional
THE SHEAR MAGIC ONE YEAR WARRANTY (cont)
You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not
amount to a major failure.
Inward postage is to be paid by the customer. Return postage will
be paid on all warranty repairs. As part of all repairs, blades will also
be sharpened for a nominal charge, as this is the most common
cause of poor performance.
Product: Shear Magic
Model: Tuffy 3000 Professional
Customer Name:
Address:
Phone:
Email:
Date of Purchase:
Reseller:
SERVICE INFORMATION
If maintenance service or service under warranty is required forward the product to:
Place of purchase or Botany Bay Imports Exports Pty Ltd - PO Box 260 BOTANY NSW 1455.
Phone: [phone], Fax: [phone]. Email: [email protected]
When returning the product for service or warranty please ensure the following:
■ Postage is prepaid
■ Use sturdy packaging to protect the product against damage in transit - such
damage is not covered by the warranty
■ Include your name, address and proof of purchase
■ Provide a detailed description of the fault
■ When sending a clipper do send the blades - but not attached to the clipper to
avoid damage in transit.
Register your product online: www.shearmagic.net.au
✁
Warranty registration on the internet or via return of the warranty registration card is
required within 30 days (thirty days) of the purchase date for coverage of the equipment.
Register online and receive an additional 6 month motor warranty to 18 months.
Visit www.shearmagic.net.au

234
SPECIFICATIONS:
Shear Magic Model Tuffy 3000 Professional
Watt 45W
Power Supply INPUT: AC 100~240V
OUTPUT: Switching Power DC 12V/2A
Rotational speed of Motor High Speed: 3000 rpm;
Low Speed: 2600 rpm
Accessories Instruction Manual, Switching
power, Lubricant, Cleaning Brush
IMPORTANT SAFEGUARDS:
When using the electrical appliance, basic precaution should
always be followed.
DANGER - to reduce the risk of electric shock:
1. Do not reach for an appliance that has fallen into water. Unplug
immediately.
2. Do not use while bathing the animal.
3. Always unplug this appliance from the electrical outlet
immediately after using.
4. Unplug the appliance when not in use and allow it to cool
down before storing it in a safe place. To disconnect the
appliance, unplug it from the wall socket.
5. Do not disassemble clipper.
WARNING - to reduce the risk of burns, fire, electric
shock or injury to persons:
1. An appliance should never be left unattended when plugged in.
2. Keep the cord away from heated surfaces.
3. Keep the air openings free of hair, fur or the like.
4. Never drop or insert any object into any openings.
5. To disconnect, move all controls to “OFF” then remove plug
from outlet.
6. Do not wrap cord around unit when storing.
7. Only use original factory parts.
The appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervised or instruction concerning use of the appliance by a
responsible person for their safety.
Young children should be supervised to ensure that they do not
play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in
order to avoid a hazard.
OPERATION:
TO REMOVE THE BLADE ASSEMBLY
Hold the unit in your hands and on the back
of the clipper, just below the blade, there is
a black metal latch. Push the latch up
towards the blade while you are holding the
latch in, gently pull the top of the blade
away from the clipper.
TO REPLACE THE BLADE ASSEMBLY
With the unit plugged into a specified AC
electrical outlet, turn the control switch to the
ON position. Holding the blade assembly by the
sides to keep fingers away from the cutting
position on the tongue. Push forward to lock
into place. Latching is automatic.
REMOVING DIRT AND HAIR
Occasionally, dirt and hair will lodge
between the blade and comb forcing
them apart and stopping the cutting
action. Remove the blade assembly, as
described above.
Push the blade sideways from its position
under the metal clip. See illustrations. Remove
the dirt and hair. Then slide, the blade back
into position.
NOTE: There is no need to remove the screws on the tension
spring when removing dirt and hair.
SHARPENING BLADES
After extended use, the blades will begin to lose factory cutting
edge and will need resharpening. To avoid the loss of clipping time,
you may wish to keep a spare set of blades on hand. Contact
Botany Bay Imports for blade re-sharpening 02 9700 0800.
OILING THE BLADE ASSEMBLY
Apply oil directly on the cutter blade just 1-2 drops. Use clipper
blade oil only.
CLEANING AND STORING
Turn the switch to OFF position. Unplug from
the electrical outlet. Remove the blade
assembly as described in OPERATIONS TO
REMOVE THE BLADE ASSEMBLY. Make sure
all blades are oiled once storing blades away.
If not oiled this causes blades to cease.
CLEAN BLADES WITH OIL TO
PREVENT CORROSION