Shinco Sdz1-70p/p User manual

Manual of dehumidifier

Model No. SDZ1-70P/P

Attention:

To prevent any internal damage, it is very important to

keep refrigeration units (like this one) upright throughout

their journey. Please leave it standing upright and outside

the box for 24 HOURS before plugging it in.

Your dehumidifier comes with two types of water pipes.1.one is a thin pipe with an inner diameter of 5 mm and a

length of 2 meters.

(This pipe is suitable for the drainage function of the pump)

2.One is a thick tube with an inner diameter of 9mm and a

length of 1 meter.

(This pipe is suitable for gravity drainage)

Thank you very much for choosing our SHINCO

dehumidifier to take care of you and your family!

Content

Important Notice...............................................02

Important Safety Instructions..........................03

Location & How it works ..................................05

Product Overview..............................................06

Operation Instruction........................................07

Removing Collected Water................................09

Care and Cleaning & Storage.............................11

Troubleshooting................................................12

Technical Data...................................................13

Warranty...........................................................14

Thank you a lot for choosing Shinco's dehumidifier, let it be a member of

your family to protect the health of the whole family.

Please read the manual carefully before you use the dehumidifier, it will

help you operate the machine better, so as to achieve the best effect and

extend the life of the machine.

IMPORTANT NOTICE BEFORE FIRST USE:

•To prevent any internal damage, it is very important to keep refrigeration units (like

this one) upright throughout their journey. Please leave it standing upright and outside

the box for 24 HOURS before plugging it in.

•Please check if there is any damage around the machine, if the machine is damaged.

Please contact customer service immediately.

IMPORTANT NOTICE FOR FIRST TIME USE:

•When you open the machine,the machine will turn on in automatic mode, and the

default dehumidification is 50% which means when the room humidity drops to 50%,

the machine will automatically shut down.

•The dehumidifiers are lightweight and easy to move. They are designed to extract

unwanted humidity while saving money due to their power saving logic. They feature

an intelligent humidistat where the desired relative humidity can be adjusted in

increments of 5% between 30% and 80% ensuring your room is not dried too much

and power is not wasted.

•The "Compressor" circuit has an automatic 3 minutes time delayed start if the unit is

turned off and on quickly. This prevents overheating of the compressor and possible

circuit breaker tripping. Make sure the tank is fitted correctly otherwise unit will not

turn on.

•When the unit is started, the fan begins to pull moisture-laden air across the

dehumidifying coils. The coils condense or draw moisture from the air, and air flows

through the top louvers into the room as dry, warm air. Moisture removed from air is

collected in a bucket on the rear of the dehumidifier. Therefore, it is normal for the

dehumidifier to discharge hot air.IMPORTANT NOTICE

•Carefully read the instructions before operating the unit.

•This appliance is for indoor use only and intended for use in a domestic environment only.

Any other use is not recommended by the manufacturer and may cause fire, electrical shocks

or other injury to user or property.

•If you are in any doubt about the suitability of your electrical supply, have it checked and if

necessary, modified by a qualified electrician.

•This dehumidifier has been tested and is safe to use. However, as with any electrical

appliance,use it with care.

•Disconnect the power before dismantling, assembling or cleaning.

•Avoid touching any moving parts within the appliance.

•Never insert fingers, pencils or any other objects though the guard.

•This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities. It is also not intended for use by those with a lack of

experience and knowledge, unless they have been given supervision or instruction,

concerning the use of the appliance by a person responsible for their safety.

•Do not leave children unsupervised with this appliance.

•Do not clean the unit by spraying it or immersing it in water.

•Never connect the unit to an electrical outlet using an extension cord. If a power outlet is not

available, one should be installed by a qualified electrician.

•Never operate this appliance if the cord, power adapter or plug is damaged. Ensure the

power cord is not stretched or exposed to sharp objects/edges.

•A damaged power supply cord should be replaced by the manufacturer or a qualified

electrician in order to avoid a hazard.

•Any service other than regular cleaning or filter replacement should be performed by an

authorised service representative. Failure to comply could result in a voided warranty.

•Do not use the appliance for any purpose other than its intended use.

•Do not tilt the unit while in use. The unit is design to work only in vertical position.

•This dehumidifier must always be stored and transported upright, otherwise irreparable

damage may be caused to the compressor; if in doubt we suggest waiting at least 24 hours

before starting the unit.

•Avoid restarting the dehumidifier unless 5 minutes have passed since being turned off. This

prevents damage to the compressor.

•Never use the plug as a switch to start or turn off the dehumidifier. Use the provided POWER

button located on the control panel.

•Always place the unit on a dry and stable surface.

•Do not dry laundry above the unit to prevent water entering the dehumidifier. Place the

laundry at least 1 meter away from your dehumidifier.

Important Safety Instructions

Warning

•Before moving the appliance,the water tank should be emptied.

•The handle on the appliance is designed to aid in its movement and should not be used to

support the full weight of the dehumidifier. When carrying the unit, it should be kept upright

and sufficiently supported from its base.

•The appliance must be placed in a room without sources of ignition (for example: open

flames, an operating gas appliance or an operating electric heater).

•Do not use or store the appliance in an unventilated space with an area smaller than 43 sq.ft

(4m2 )per unit.

•If the appliance is installed, used or stored in an unventilated room, the room must be such

as to prevent stagnation of possible leaks of refrigerant gas as there could be a danger of fire

or explosion once the refrigerant comes into contact with electric heaters, stoves or other

sources of ignition.

•Do not use the product and contact the retailer for advice, if damage has occurred to the unit

which may have compromised the refrigerant system.

•Any repairs or maintenance must only be carried out on the unit by a suitably qualified

engineer.Before opening and servicing the unit,the authorized engineer must be in

possession of a copy of the manufacturer’s service manual and must follow the safety

information contained within it to ensure all hazards are minimized.

•The refrigerant system should not be perforated or punctured.

•Do not place the unit next to heat sources (e.g. electrical fires, fireplaces, etc.)

•Avoid mishandling the dehumidifier. Dropping, throwing the unit can cause damage to its

internals and increases the risks of operating it.

•Do not store or use gasoline, petrol, paint, solvents or other flammable vapours or liquids in

the vicinity of this dehumidifier or any other appliance.

•This dehumidifier must not be used in spaces where there is a high concentration of gases,

solvent or other volatile organic compounds; in very dusty environments; in any domestic,

commercial or industrial environment where the air composition is flammable.

ELECTRICAL INFORMATION

•Be sure the dehumidifier is properly grounded. To minimize shock

and fire hazards, proper grounding is important. This power cord is

equipped with a three-prong grounding plug for protection against

shock hazards.

•Your dehumidifier must be used in a properly grounded wall

socket. If your wall socket is not adequately grounded or

protected by a time delay

fuse or circuit breaker, have a qualified electrician install the

proper socket.

•Avoid fire hazard or electric shock. Do not use an extension cord

or an adapter plug. Do not remove any prong from the/power

cord.

Location & How it works

•A badly positioned dehumidifier will have little

effect. In positioning the dehumidifier,please

ensure circulation of air is not restricted around

the unit. Maintain a minimum clearance of 20 cm

(8 in) on the sides and back of the dehumidifier

and 50cm (19.7 in) on the top of the dehumidifier

to allow for proper air circulation.

•The recommended ambient operating

temperature is between 5°C (41°F) and 35°C (95°

F).The unit will not work properly if the

temperature is out of this temperature range, or

the performance of the unit will fall greatly.

•TO REDUCE NOISE LEVELS:

Place a piece of carpet or a rubber mat under the unit to reduce any vibrations while the unit

is running. Our dehumidifier uses compressor technology to extract water from the

environment.

Location

How it works

How does the dehumidifier work?

It helps to think of your dehumidifier like a vacuum

cleaner: it sucks in air from your room, removes the

moisture, and then blows the air back into the room

again.

First, humid air is pulled into the Shinco dehumidifier

through the grill on the back of the unit. The warm,

moist air is pulled across freezing-cold pipes where

water from the moist air collects (kind of like water

gathering on a glass of iced tea during a hot summer

day.) As the water collects on the pipes, it drips down

into the drain bucket for later removal. While the water

is collecting in the drain bucket, the now moisture-free

air is reheated so it can be blown out the top of the

unit and back into the room.

Product Overview

Operation Instruction

1. Plug the power cord into a properly grounded 115 volt AC outlet.

2. To turn the unit on, press the ON/OFF button. The unit will run

in the factory setting of AUTO mode and low fan speed. And the default

dehumidification is 50%.And the unit will display the RH,if the room humidity

drops to 50%, the machine will automatically shut down.

3. Press to switch between automatic mode(when it reaches the humidity

you set, the unit will stop working)and continuous mode （ it will always

dehumidify without stopping）.When unit is in operation,you can press

for 3 seconds to lock all the buttons on the control panel in case children will

play on it. Re-press it for3s, you can cancel the function.

4.If you switch to the auto mode,you have to set your ideal humidity by

pressing the .The humidity level can be set within a range of 30% RH

(Relative Humidity) to 80% RH (Relative Humidity) in 5%increments. If you

switch to continuous mode,regardless of the relative humidity in the room,

the compressor starts, the fan runs at high speed by default, and the wind

speed can be adjusted.

Attention:Press this button for 3s to start or shut the Pump function.(Please connect

continuous pipe with an inner diameter of 5mmbefore starting pump function.)

5.You can also press to change the fan speed to HIGH or LOW. The

indicator light will show the setting you have selected. A higher fan speed will

result in quicker moisture removal.

6.Then to run the dehumidifier for a preset amount of hours, press ."0"

blinks on the display. Set the time you wish the appliance to operate between

1 and 24 hours. And you can set time to turn on this machine by pressing this

button in standby.

8.Before storing the unit , pls dry inside of the dehumidifier by

pressing .This will prevent mold from forming during storage.

Auto Shut Off

When the bucket is full and/or the humidity setting is reached, the

dehumidifier will be shut off automatically.

Wait 3 minutes before resuming operation

To avoid any damage to the dehumidifier, the dehumidifier will not start

operation following a complete cycle until after three (3) minutes. Operation

will automatically start after three (3) minutes.

Auto Defrost

When frost builds up on the evaporator coils, the compressor will cycle off

and the fan will continue to run until the frost disappears.

Auto-Restart

If the dehumidifier shuts off unexpectedly due to power being cut, the

dehumidifier will restart with the previous function setting automatically

when the power resumes.

Note: SMART FUNCTIONS

7.If "Water full" lights up and the display shows "FL", the water tank needs

to be emptied (see "Removing Collected Water") ．After reinstalling the

emptied water tank, the dehumidifier restarts automatically after three

mins.

Removing Collected Water

There are three ways to remove collected water:

1. Use the bucket

When the bucket is full, remove the bucket and empty it.

Do not move the unit at this time otherwise water may spill on the floor.

Press sides of bucket gently to unclip the bucket from the unit.

Remove the bucket as shown in the photographs below and empty the

bucket.

Discard water from bucket. Water is not potable and cannot be used for

drinking

2.Pump drainage.

Unscrew the water cap counterclockwise, and then pull out the black

rubber water plug.

•First, to use the pump function, you need to connect a tube with an

inner diameter of 5mm. We have two tubes delivered together with

the machine. The thinner one is a 5mm tube, but the length is only 2

meters.

•Then,after you connect the tube, you need to press the Humidity

Setting button(which is under the pump indicator light) for three

seconds to start the pump function.

•And the pump indicator light will turn in red.This means that the

function of your pump is turned on.

Note:Make sure the connection is tight and there is no leaking.

Lead the water hose to the floor drain or a suitable drainage facility, the

drainage facility should be lower than the drain outlet of the dehumidifier.

Be sure to run the water hose sloping downward to let the water flow out

smoothly.

Improper installation or use of hose may result in water filling up the bucket

and causing the unit to shut off. Empty water bucket if shut-off occurs, then

check dehumidifier location and hose for proper installation.

For example, the following conditions will cause water to flow into the water tank.

Connect the garden water pipe, and the water pipe is too long and the water

pipe bends and generates pressure, making the water unable to drain out.

The end of the pipe is immersed in water, and the water pressure prevents the

water from draining smoothly.

If bucket fills after a long period of continuous use, remove and check the water

pipe for blockage by dirt.

3.Continuous Drainage:

Water can be automatically be emptied into a floor drain by attaching the

dehumidifier to a water hose.

•Cut off the power;

•Unscrew the water cap counterclockwise and pull out the rubber water

plug；•Connect the water pipe (Inner diameter * wall thickness * length= 9mm *

2mm * 60cm) to the drainage outlet.

Care and Cleaning & Storage

Warning:

Turn the dehumidifier off and remove the plug from the wall outlet before cleaning.

1. Clean the bucket

Clean the bucket with water every two weeks.

2. Clean the air filter

Clean the filter with potable water at least once every 30 days.

(Notes: It must be air-dried naturally after cleaning. Never use any type of dryer.)

3. Storing the dehumidifier

When not using the dehumidifier for long time periods

- Press the drying inside button .

- Clean the main dehumidifier, bucket and air filter.

- Wrap the cord and bundle it with the band.

- Cover the dehumidifier with a plastic bag.

- Store the dehumidifier upright in a dry, well-ventilated place.

Troubleshooting

(Before contact our customer service, review this list. It may save your time and expense. This list

includes the most common occurrences that are not the result of defective workmanship or materials in

this dehumidifier.)

(Please contact our Customer Service by writing an email to: [email protected].

if dehumidifier operates abnormally or does not operate, and the solutions above are

not useful.)

Issue Cause Solution

Hot or cold

air being

produced

Normal Operation

When the unit is in dehumidifying mode it absorbs humid air from

room and freezes it to reduce the humidity.

During the cold cycle there should be cold air coming out of the unit,

During the defrost cycle hot dry air should be coming out of the outlet

grill.

Unit does

not operate

Is the plug properly inserted in

the socket? Insert the plug into the socket and turn the switch on.

Does the tank full indicator is

red?

Tank full, float displaced or tank not properly inserted. Empty tank,

check float and make sure tank is properly inserted in unit.

Dehumidifier

does not

extract

water

Is the unit set to a humidity level

lower than the one in the room?

Set the humidity level on the humidistat bellow current humidity

reading.

Is the temperature too low for

water extraction to be efficient? Increase temperature in the room or reposition the unit.

Is any intake grill or discharge

blocked? Is the unit too close to

walls.

Remove obstructions and restart the unit.

Ensure a distance of at least 7.9 in(20cm) between the unit & walls

Airflow

seems weak Is filter dirty or clogged? Please service the filters regularly as per user manual.

Unit is noisy

during

operation

Is the unit on an uneven

surface? Please place on flat horizontal surface.

Is filter clogged? Please service the filters regularly as user manual.

E2 Error

Code Temperature sensor error Use the unit within the prescribed temperature range. Unplug the

unit, rest and plug it back in. If error repeats, call for service centre.

P1 Error

Code Appliance in defrost mode This is normal operation to prevent a build up of ice on the coils.

Leave the unit, and it will return to normal operation.

FL Error

Code Water tank full notification Tank is full or is not in the right position-- Empty the tank and replace

in the right position.

E1 Error

Code The coil sensor detects anomaly Please contact our customer service.

CL Error

Code

The unit is in the internal drying

state,which is normal .

When you press the inside drying button,this code will display

on the screen .

LC Error

Code

The child lock function starts. When you press the Mode button for 3s,this code will display

on the screen.

ModelSDZ１-70p/pColorwhiteSpecificationPower supply110~120V/60HzPower input (w)520Rated current(A)8Moisture Removal (80°F,RH 60%)70Water tank capacity(Water full)(Liter)7RefrigerantR410ANoise level (dbA)42TypeMechanical/ElectronicElectronicFeaturesTimer24HDisplayLEDwater-full alarmYEScloth-dry functionYESContinuous drianage functionYESFrost preventionYESSpecificationNet Weight (Kg)19.5Body size(ＩＮ)24.2 × 14.9 x 10.5Package size(ＩＮ)25.67 × 16.93 x 12.13 TECHNICAL DATA