ShineACS SL-C10 Series User manual

KRFID EM Card Cabinet Lock SL-C10 Series User Manul
www.acslocks.com
3-1
RFID EM Card Cabinet Lock SL-C104/SL-C105/SL-C107
User Manual
1. Componant of A Cabinet Lock …………………….…………………….………..…………1
2. Functions and Features ………………………………………………….……………………..1
3. EM Card Lock Operation ……………………………………………………………………….1
3.1 Initialization…………………………………………..………………………………………1
3.2 Single-card-unlocking
mode………………………………...…………………………2
3.3 Double-card-unlocking
mode.……………………………...…………………………2
1. Componants of A Cabinet Lock: 1 set of lock cover with EM card reader,
1 set of lock core and catch assembly and 1 unlocking card
2. Functions and Features:
(1)Singgle-card-unlocking and double-cards-unlocking modes are available
for chioce
(2) Power supply: 4pieces of AA 1.5v Alkaline Batteries
(3)If voltage is lower than 4.8V, the lock will alarm whenever unlocked by
TM card.
(4)Batteries life span: more than 15 months
(5)External power interface(Audio interface)
(6)Bouncing function: when the lock opened by TM card, the cabinet door
will be bounced autometically so that handle is not needed.
(7)In certain emergency cases, the lock can be opened mechanically.
(8)Gear engagement ensures safe and reliable operation.
(9)Wristband for carrying the TM card: convenient, waterproof,
heat-resistant, etch-proof.

KRFID EM Card Cabinet Lock SL-C10 Series User Manul
www.acslocks.com
3-2
(10)Unlocking method: TM card unlocking
(11)Technical data:
Operating temperature: -30℃～80℃
Antistatic behavior: >15,000V, information can be save though in
strong static
Static Power Consumption: <5μA
Dynamic Power Consumption: about 200mA
Low voltage alarm: 4.8V
Relative humidity: <95%
3. EM Card Lock Operation:
3.1 Initialization
To initialize the circruit board, please press the white button on the
circruit board for about 3 seconds( or use something acerose, like toothpick, to
jab into the small hole on the lock core). Blue light will be on during this process.
Loosen the button when you hear a sound of “beep”. At the moment that you hear
a long sound of “beep” with 5 short soundsof “beep” following, the lock is
initialized(all cards of the lock are cleared) and in the single-card-unlocking
mode.
If you press on the white botton again during the 5 short sounds of “beep”
and loosen it when you hear double sounds of “beep”, the lock would be into the
double-card-unlocking mode.
3.2 Single-card-unlocking mode:
1) Setting a Master card: After initialization, take a EM card to contact
the EM reader. Two sounds of “beep” with blue light flashing indicate the card is
read and set as Master card.
Functions of a Master card: opening the lock, adding unlocking cards
and clearing opening cards.
Opening the lock by the Master card: take the Master card to contact
the EM reader and then take away the card, the lock would be opened.
When a Master card opens the lock, one sound of “beep” with blue light
flashing for 6 times indicate that this is a Master card in the
single-card-unlocking mode.
2) Adding unlocking cards: Take the Master card to contact the EM
reader, then two sounds of “beep”, motor rotating and the lock opened(with lock
bolt back into the lock core) indicate the lock is in the state of adding unlocking
cards. You can add unlocking cards during the blue light flashing for 6 times --
take another EM card to contact the EM reader, one short sound of “beep”
indicates the card is read and set as unlocking card successfully. You can add
cards continuously, and 15 unlocking cards can be set at most.
3) Clearing all of the unlocking cards: Take the Master card to contact
constantly the EM reader. If the card is read successfully, 5 rapid sounds of “beep”

KRFID EM Card Cabinet Lock SL-C10 Series User Manul
www.acslocks.com
3-3
with blue light flashing for 5 times and following 3 long sounds of “beep” with
blue light flashing for 3 times indicate that all of the unlocking cards are cleared.
3.3 Double-card-unlocking mode
1) Initialization: Supply power, and then press the white button on the
circruit board for about 3 seconds( or use something acerose, like toothpick, to
jab into the small hole on the lock core). Blue light will be on during this process.
Loosen the button when you hear a sound of “beep”. During the period that you
hear 6 sounds of “beep” following (1 long sound and 5 short sounds), press the
white button again, then you will hear double sounds of “beep” with blue light
flashing twice. Double sounds with light flashing twice repeat 5 times indicate
the double-card-unlocking mode is initialized successfully.
2)Setting the Master card: After initialization, take a EM card to contact
the EM reader, then two sounds of “beep” with blue light flashing twice indicate
the card is read and set as Master card. When the door unlocked by Master card,
there would be a sound of “beep” from the lock with blue light flashing 6 times,
which indicate this is the Master card in the double-card-unlocking mode.
3) Adding unlocking cards: Take the master card to contact the EM
reader, then one sounds of “beep”, motor rotating, the lock opened(with lock bolt
back into the lock core) and blue light flashing for 6 times indicate the lock is in
the state of adding unlocking cards. You can add cards during the blue light
flashing – take a guest card to contact the EM reader, a short sound with blue
light on indicates this card is read and setting as guest card successfully; next
take a service card to contact the EM reader, 1 short sound with blue light on
indicates this card is read and setting as service card①. At most, 14 service cards
can be added for a lock.
Double-card-unlocking mode: take the customer card to contact the EM
reader. One short sound with blue light flashing indicates the card is read
successfully. Then take a service card to contact the EM reader. Simple music with
blue lights on indicates the card is read successfully. At this moment, the motor
will rotate and door will be opened( with lock bolt back into the lock core).
*Note: In the double-card-unlocking mode, the first card added by the
Master card is guest card, and all of the following cards are service cards. When
unlocking the door, only when the customer card and a service card together can
the lock be unlocked. Which card to be read first is not required. Use two service
cards or two guest cards can not unlock the lock.
4) Clearing all of the unlocking cards: Take the Master card to contact
constantly the EM reader. If the card is read successfully, 5 rapid sounds of “beep”
with blue light flashing for 5 times and following 3 long sounds of “beep” with
blue light flashing for 3 times indicate that all of the guest card and service cards
are cleared.