Yale MORTISE 8800 SERIES User manual

Installation Instructions
Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
This product can expose you to
lead which is known to the state
of California to cause cancer and
birth defects or other reproductive
harm. For more information go to
www.P65warnings.ca.gov.
WARNING!
8800 Series Mortise Lock
Used with Sectional Trim and V Series Indicators
80-8800-0016-000 12/20

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
2
8800 Series
Installation Instructions
Mortise Lock
80-8800-0016-000 12/20
1Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Indicator Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Lock Set Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Rehanding Indicator (if required). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Prepare Door for Mortise Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Install Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Prepare Door for Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Install Levers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Install Indicator Mounting Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Install Indicator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Install Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Install Outside Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Perform Functional Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Indicator Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3
2
4
TOC Table of Contents
5
6
1
2
3
6
7
8
9
1 Tools Required
#2 & #3 Phillips
head screwdrivers
Flat blade
screwdriver
1/8" Allen
Wrench 3/32" Drill bit T20 Torx Screw
with Tamper Pin
Driver
4
5

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
3
Installation Instructions
8800 Series
Mortise Lock
80-8800-0016-000 12/20
2 Indicator Variants
4 Rehanding Indicator (If required)
Depending on function and option ordered,
indicators are provided in the following
variations, these instructions detail how to install
with cylinder, however other variations follow
similar instructions. (Figure 1)
Contact factory for any questions.
Figure 1 Cylinder - For
installation
on inside or
outside of door.
Thumbturn -
For installation
on inside of
door.
Coin Turn - For
installation
on outside of
door.
No input / blank -
For installation on
inside or outside
of door.
3 Lock Set Configuration
To re-hand lock, see instructions on lock body.
LH
Left Hand
Hinges Left
Open Inward
RH
Right Hand
Hinges Right
Open Inward
LHRB
Left Hand
Reverse Bevel
Hinges Left
Open Outward
RHRB
Right Hand
Reverse Bevel
Hinges Right
Open Outward
Figure 2
Verify hand and bevel of door. (Figure 2) Spindle Cam Position for Locks with Deadbolt
(*includes 8864 function)
Outside Indicator Inside Indicator
Door Hand LH/LHRB
Spindle Cam Position for Locks without Deadbolt
(*Does not include 8864 function)
Door Hand LH/LHRB
Figure 3
Note:
Stand on outside of locked door when determining door hand.
Next, verify inside and/or outside indicators are handed correctly,
using Spindle Cam Position chart. (Figure 3) If they are handed
correctly, skip to Step 5 “Prepare Door”.
If they are not handed correctly:
1. Remove retaining pad and spindle cam from assembly.
(Figure 4)
2. Position spindle cam in correct direction for door hand.
(Figure 3)
Important:
• For thumbturn indicators, make sure thumbturn is positioned
in the 12 o’clock direction as shown. (Figure 5)
3. Slide spindle cam post into correct slot of display slide.
(Figure 4)
4. Re-seat retaining pad into original position.
5. Return indicator to the vacant/unlocked position for
installation.
Thumbturn
Position
Figure 4
Figure 5
Retaining Pad
Spindle cam
Display
slide slot
Door Hand RH/RHRB
Inside Indicator Outside Indicator
Inside Indicator Outside Indicator
Door Hand RH/RHRB
Outside Indicator Inside Indicator

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
4
8800 Series
Installation Instructions
Mortise Lock
80-8800-0016-000 12/20
5 Installation
1Prepare Door for Mortise Lock
Prepare door for function holes, size, and location
according to 7088-0006 door marker template, if not
already prepped.
Figure 6
Inside of door Outside
of door
RH door
shown
Lock
Lock
Screws
2Install Lock
1. Verify strike location according to
template. Clean out door pocket and
door edge of debris.
2. Make sure handing of lock matches
handing of door. Slide lock into door.
(Figure 6)
3. Temporarily hand tighten two (2)
lock screws (#12 x 1-1/4" wood
screws, or #12-24 x1/2" machine
screws).
NOTE: Keep door open until installation is complete.
3Prepare Door for Indicator
Control
Hub
Guide
Template
Figure 7
Mark
holes
with
pencil
1. Insert template guide into control hub on
side where indicator will be used. (Figure 7)
2. Slide indicator template over template guide.
Important: Make sure the template is properly centered
and aligned to ensure smooth indicator operation.
3. Mark the four (4) hole positions indicated on tem-
plate.
4. Remove guide and template.
5. If indicators are being used on both sides of door,
repeat steps 3.1 through 3.4 for opposite side.
6. Remove lock body.
7. Drill four (4) marked holes with 3/32" diameter bit,
by 1/2" deep.
8. Reinstall lock body and hand tighten screws.
NOTE: If retrofitting over an existing product, ensure door
surface is free of chips and debris around holes so
indicator will sit flat against door surface.

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
5
Installation Instructions
8800 Series
Mortise Lock
80-8800-0016-000 12/20
5 Installation, continued
4Install Levers
Figure 8
Figure 9
Figure 10
1. Insert outside mounting plate through
door and lock body, and hold. (Figure 8)
2. Align and fasten inside mounting plate
securely with two (2) #8-32 x 1-1/4"
screws.
3. Install roses on inside and outside
adapter plates.
5Install Indicator Mounting Plate
6Install Indicator Assembly
1. Screw indicator mounting plate to door with four
(4) #6 x 3/8" sheet metal screws. (Figure 9)
2. If indicators are being used on both sides of door,
repeat step 5.1 for opposite side.
1. Verify lock is in unlocked state (turn outside
lever to confirm).
2. Verify indicator is in vacant/unlocked position.
3. Assemble indicator assembly onto mounting
plate. (Figure 10)
4. Secure indicator assembly to door with two (2)
machine screws.
• Use #832 x 5/8" screw for top
• Use #832 x 3/8" screw for bottom
5. If indicators are being used on both sides of
door, repeat steps 6.1 through 6.3 for opposite
side.
NOTE: Torx security screws recommended.
Outside
of door
Inside of door
Inside of door Outside of door
Inside lever
Rose RH door
shown
Set Screw
#832 x 11/4"
Screws
Inside MountingPlate
Outside Mounting Plate
Mounting
Plate
#6 x 3/8" Screws
Indicator
Assembly
#832 x 5/8"
Screw
4. If included, press rose adapter into rose and
mounting plate assemblies.
5. Unscrew inside spindle 1/2 turn and align
ramp in the horizontal position.
6. Slide plastic bushing onto outside lever and
spindle and insert through the lockbody.
7. Slide plastic bushing onto inside lever and
attach to spindle. Then tighten inside lever
set screw.
Rose
Plastic Bushing
Rose Adapter Rose Adapter
Plastic Bushing
Outside Lever and Spindle
#832 x 3/8"
Screw

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
6
8800 Series
Installation Instructions
Mortise Lock
80-8800-0016-000 12/20
5 Installation, continued
7Install Cylinder
Figure 11
Figure 12
Figure 13
1. Thread cylinder into lock until flush with indicator
escutcheon surface. (Figure 11)
• Pull key slightly out of cylinder to help thread into
lock body.
2. Tighten cylinder clamp screw with #2 Phillips
screwdriver.
• Check operation and adjust if necessary.
Notes:
• Yale logo must be horizontal and on top. (See
Figure 12)
• If double cylinder function is used, repeat steps 7.1
and 7.2 for second cylinder.
• Interchangeable Core cylinders require a control
key to remove and install the core. This is not pro-
vided standard. It must be requested seperately.
Cylinder
Cylinder
Clamp
Screw
Key and cylinder must be rotated as shown.
8Install Outside Front
1. Tighten the two (2) lock screws completely:
(Figure 13)
2. Attach outside front with two (2) flat head screws
#8-32 x 1/4".
9Perform Functional Check
DO NOT FORCE if resistance is encountered during
functional check. Refer back to Rehanding Indicator (if
required) section to ensure correct handing. Rehand if
necessary.
1. Insert key into cylinder (if present) and rotate:
• Ensure there is no friction against lock case or any
other obstructions.
2. Check key retracts latch:
• Key should rotate freely.
3. Throw deadbolt (if present):
• Check key retracts both deadbolt and latch.
4. Test levers:
• Confirm latch and deadbolt (if installed) retract.
5. Verify indicator displays correct status when
locked and unlocked.
Correct Incorrect
Lock Screw
Outside
Front
#832
x 1/4"
Screws
Lock Screw

Copyright ©2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited
For technical support contact Yale®at 800.438.1951 x5033 or [email protected]
7
Installation Instructions
8800 Series
Mortise Lock
80-8800-0016-000 12/20
6 Indicator Parts List
4A
4B
4C
4D
7
6
5
6
4
3
21
6
Figure 14
#Description Part # Req.
1
Sectional Escutcheon - Cylinder 81-0472-4000 x finish 1
Sectional Escutcheon - Coin Turn 81-0471-4000 x finish
Sectional Escutcheon - Thumbturn 50-8800-0364 x finish
Sectional Escutcheon - No Input/Blank 81-0473-4000 x finish
2 Indicator Window 856F049 1
3
Indicator Display Assembly - Green Unlocked / Red Locked 82-5602-4000
1
Indicator Display Assembly - Green Vacant / Red Occupied 82-5603-4000
Indicator Display Assembly - Green Unlocked Icon / Red
Locked Icon
82-5604-4000
Indicator Display Assembly - White Unlocked / Red Locked 82-5605-4000
Indicator Display Assembly - White Vacant / Red Occupied 82-5606-4000
Indicator Display Assembly - White Unlocked Icon / Red
Locked Icon
82-5607-4000
Indicator Display Assembly - Green Ouvert / Red Fermé 82-5684-4000
Indicator Display Assembly - Green Libre / Red Occupée 82-5685-4000
4A Indicator Spindle Cam - Thumbturn 50-8800-9328
1
4B Indicator Spindle Cam - Cylinder/No Input / Blank 50-8800-7335*
4C Indicator Spindle Cam - Cylinder Overtravel 50-8800-0378*
4D Indicator Spindle Cam - Thumbturn Overtravel 50-8800-0346
4E Indicator Spindle Cam - Coin Turn 50-8800-7339*
5 Indicator Retaining Pad 81-0749-9000 1
6 Sectional Indicator Screw Pack 85F497 FIN* 1
7 Sectional Indicator Mounting Plate 855F658 1
8 Sectional Indicator Template Kit (not shown) 50-8800-9343 1
*These parts are for 1-3/4" standard thickness doors. For other thicknesses, contact the factory.
NOTE: Reference 8800 Series parts manual for all lock body parts.
4E

80-8800-0016-000 12/20
THE YALE BRAND, with its unparalleled global reach and
range of products, reassures more people in more countries
than any other consumer locking solution.
THE ASSA ABLOY GROUP is the world´s leading
manufacturer and supplier of locking solutions, dedicated to
satisfying end-user needs for security, safety and convenience.
Yale Commercial is a business associated with ASSA ABLOY Access and Egress
Hardware Group, Inc., an ASSA ABLOY Group company. Copyright © 2020,
ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved.
Reproduction in whole or in part without the express written permission of
ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited. Patent
pending and/or patent www.assaabloydss.com/patents.
U.S.A.
Yale Locks & Hardware
Address: 225 Episcopal Road
Berlin, CT 060374004
Tel: 18004381951
Fax: 18003380965
yalecommercial.com
Canada:
ASSA ABLOY Door Security Solutions Canada
Address: 160 Four Valley Drive
Vaughan, Ontario L4K 4T9
Tel: 18004613007
Fax: 18004618989
assaabloydss.ca
International:
ASSA ABLOY Americas International
Tel: 19058217775
Fax: 19058211429
assaabloyai.com
Contact Us
Customer Service Phone:
1-800-438-1951
Customer Service Fax:
1-800-338-0965
Technical Product Support:
[e-mail]
Customer Service:
[e-mail]
Website:
Yalecommercial.com
Email for orders:
[e-mail]
Trusted every day
Part of ASSA ABLOY