Shinybow USA SB-5544LCM User manual

INSTRUCTION MANUAL
MODEL : SB-5544LCM
4x4 AUDIO-VIDEO MATRIX SWITCHER
4x4 AUDIO-VIDEO MATRIX SWITCHER
Composite Video-Stereo Audio Matrix Switcher Series
Thank you for purchasing the SB-5544LCM 4x4 Composite Video-Audio Matrix Switcher. You will find this unit
easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use
4x4 Composite Video and Audio Matrix Switcher.
MULTIMEDIA AUDIO AND VISUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF AGENERAL NATUREAND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for sufficient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed,stored in aretrieval system,or anyof itspart translated
into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 1997. All Rights Reserved.
Version 1.2 MAR 2014
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
CONTENTS
INTRODUCTION ..............................................................1
FEATURES & SPECIFICATIONS ..................................... 2
FRONT PANEL ................................................................. 3
BACK PANEL .................................................................... 6
REMOTE CONTROL ....................................................... 7
REMOTE PROTOCOLCOMMANDS ................................ 8
IR EXTENDER .................................................................. 9
RS-232 SERIALINTERFACE.......................................... 11
TYPICAL APPLICATION ................................................12
INTRODUCTION
Congratulations on your purchase of one of the most innovative
4x4 AV (Composite Video/Audio) matrix switching product on
the market Today. The SB-5544LCM is a true Matrix Routing
Switcher for AV (Composite & Stereo Audio) signals. Full support
any NTSC or PAL Composite Video & Stereo Audio system. It is
a (4) individual Composite Video and Stereo Audio inputs with (4)
individual Composite Video and Stereo Audio outputs. Because it
is a matrix router, any input may be routed to any output; or the
same input may be routed to all outputs or any combination. It
completely eliminates the need to constantly move around video
audio input and output cables. The SB-5544LCM is useful for
Matrix signals from Composite Video and stereo audio source
devices (such as: VCRs, Camcorders, Video Game Consoles,
Video CDs, DVDs, Satellite Receivers, CAT5 Set Top Boxes, etc.)
To Composite Video/Audio destination devices (such as: LCD TV,
HDTV, Plasma displays, Projectors, etc.). Selection of inputs is
made via the Front Panel push buttons or an Infrared Remote
Control unit or RS-232 control by computer.
PACKAGE CONTENTS
Check that you have the following components;
• SB-5544LCM Switcher
• IR remote controller (SW-5544LCM)
• 19-inch ear mount bracket (Part # 1U-440 L)
• IR extender SB-100 receiver (300M length)
• IR extender SB-100C receiver (2M length)
• RS-232 Cable
• CD contents: Windows GUI
• RS-232 operation manual (V2.0)
• Users Guide
• Power Supply: 12VDC, 2AUniversal Type 50/60Hz, 100~240 VAC
1

FEATURES & SPECIFICATIONS
FEATURES
• Support 4x Inputs To 4x Outputs Matrix Switcher.
• VideoAudio signals support Composite Video and Stereo Audio (AR/AL)
• High Bandwidth Video 450MHz each Composite Video ports.
• Support IR remote and IR External, front panel and RS-232 serial interface protocol Controls.
• Compatible NTSC or PAL TV Video systems.
• RS-232 control via a PC Drive compatible PC win-98/2000/XP.
• Various User Interface control :
• Attached Window based control software for Desktop or NB control via RS-232 port.
• The Front Panel button via manual control.
• IR remote control or IR external to control Switcher
• Support desktop with 19 inch 1RU Rack mount pack.
• Power supply use Universal Type Switch AC 100~240VAC, Frequency 50/60Hz
SPECIFICATIONS
• Type of Switcher: 4 inputs To 4 outputsAudio-Video Matrix Switcher
• I/O Signals:
• Video: Composite Video (0.5~1.0 Vpp, 75Ohms. RCA(Yellow)
• Audio: Stereo Audio (AR/AL). Via 2x RCAconnector (Red/White)
• Video Bandwidth: 450MHz (-3db, 200mVp-p)
• Audio specification: 20Hz ~ 20KHz
• Source Status: Automatically scan sources Inputs via LED
• Low all hostile crosstalk: -83 db@5MHz
• Gain control: 60MHz-0.1 db gain flatness
• IR Frequency: 38Khz
• IR External distance:
• SB-100 phone-jack 3.5mm 3C cable ( 1000 feet / 300 meters Max.)
• SB-100C phone-jack 3.5mm 2C cable ( 2 meters)
• RS-232 protocol control: STD RS-232 interface serial via PC DRV
• Rack Mount: Support Rack mount 1RU High 19” pack (#1U-300L)
• Safety Approvals: CE, FCC, RoHS, REACH
• Dimensions (LxWxH): 11.97 x 5.90 x 1.73 in (304 x 150 x 44mm)
• Power Supply: DC-12, 2A Universal Switch Type AC100~240V, 50/60Hz
• Power Consumption: 750mA Maximum full load
• Shipping Weight (net): 3.25kgs / 5.41 lb
As product improvements are continuous, specifications are subject to change without notice.
2

FRONT PANEL
FRONT PANEL
1. POWER ON SWITCH
The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power. The
Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked.
2. INPUT STATUS DISPLAY
Input sources 1 to 4 LED illuminates blue to indicate that a video source is present on that input.
3. OUTPUT STATUS DISPLAY
Each Output (destination) Channel shows which input (source) is assigned.
4. DESTINATION SELECT BUTTONS
Separate outputs 1 thru 4 select buttons are provided for each destination assignment.
Routing can be Source to Destination or one source to multiple destinations.
Example : Press Destination 1,3,4 then press Source 2 will route Input 2 to Output 1,3,4 respectfully.
5. SOURCES SELECT DOWN BUTTONS
Separate inputs 1 thru 4 select buttons are provided each source selection.
6. IR SENSOR
The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
7. 19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount bracket (part # 1U-440L) INCLUDED. Image shows rack mount bracket attached.
3

FRONT PANEL
FRONT PANEL
8. FUNCTION KEY - ALL
Disables (mute) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show ”0” indicating all destinations have no video selected.
Option 2
- Press ALL followed by Source 1 thru 4. The display will show the Source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
9. FUNCTION KEY - OFF
Disables (mute) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 8 output destination. The display will show “ 0 “ for the selected channel indicating no video selected.
10. FUNCTION KEY - RECALL
The system will show previously stored presets, up to a total of 8. Presets are stored in local memory using Source keys 1 thru 4 or
Destination keys 1 thru 4 as the memory preset location.
- Press RECALL button.
- Press 1 thru 4 on either Source or Destination row.
- Press ENTER The pre-set configuration will execute.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
11. FUNCTION KEY - ENTER
Press ENTER to confirm entries.
4

FRONT PANEL
FRONT PANEL
12. FUNCTION KEY - MEMORY
The system will show store presets, up to a total of 8. Presets are stored in local memory using Source keys 1 thru 4 or Destination keys
1 thru 4 as the memory preset location.
- Configure desired matrices.
- Press MEMORY button.
- Press 1 thru 4 on either Source or Destination row.
- Press ENTER to ready memory location.
- Or press MEMORY again to cancel operation.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
13. FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable front panel.
5

BACK PANEL
BACK PANEL
CONNECTING THE HARDWARE
Please study the panel drawings below and become familiar with the signal input-output, Power requirements plus any controls present.
Before using the switcher, please take the time to make certain that the device you wish to connect to its inputs is functioning properly in
all respects. Verify that the video and audio signals are present and are being displayed properly on a suitable device.
If all is well connect the appropriate cables between the output of the device you wish to distribute to output(s) of the switcher to the
carious devices you wish to feed a signal to. Lastly, connect theAC to DC adaptor, connect the DC connector to the switcher first and then
plug the adaptor into a functional AC outlet.
6
1. DC POWER INLET:
The Switcher is fitted with a DC power plug-park input connector.
Please ensure that the plug-park used is of an approved type and
is of sufficient current carrying capacity with the correct voltage
and connector polarity. 12Volt DC power supply 2A Max.
2. IR EXTENDER CONTROL
Support one of IR Extender (IR input)
Extend distance maximum 300 M / 1000 ft
Note: DO NOT install or remote any connections while the
power is ON.
3. RS-232 CONNECTION:
RS-232 control port to allow for interfacing to a PC, such as a
computer or touch panel control, to the switcher via this DB-9pin
Female connector for serial RS-232 control.
4. INPUTS-1~4 COMPOSITE/AUDIO(AR/AL):
Connect a signal source of Composite Video and Stereo Audio
(AR/AL) devise to 4x4 matrix switcher.
Input 1~4 port source signals: Composite Video/Stereo Audio,
3x RCA Connectors
5. OUTPUTS: 1~4 COMPOSITE/AUDIO(AR/AL):
Connect a signal of Composite Video and Stereo Audio (AR/
AL) direct to Female RCA connector. This connector supports
Composite Video and StereoAudio display device.
Output 1~4 display port signals: Composite Video and Stereo
Audio, 3x RCA Connectors
Power Jack:
DC Jack - Inner OD Ø 2.1 mm (+)
Outside OD Ø 5.5mm (GND)
Power input -12VDC, 2A
IR Extender Jack: Female Jack - inner OD Ø 3.5 mm
Remote Port: DB-9pin Female connector
Composite VideoAudio Via 3x RCAs
Note: With 3x RCA female connectors.
Composite VideoAudio Via 3x RCAs
Note: With 3x RCA female connectors.

7
REMOTE CONTROL
Before making any connections to the SB-5544LCM. Observe the following:
Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%).
Ensure that the power switch is OFF.
Ensure that all system grounds (earth) are connected to a common point.
Avoid powering equipment within a system from multiple power sources that may be separated by large distances.
Connect all audio video sources and destination equipment.
Power up all source and destination audio-visual sources.
For each destination output select the appropriate input source by using the front panel input 1-4 select buttons. The supplied IR remote control.
Or through the RS-232 serial communications port.
Upon power up the switcher will return to its last used setting before Powered down.
REMOTE CONTROL
IR REMOTE : SW-5544LCM
IR PCB : RA-02
IR CODE : 20DF
1./2. SWITCH POWER ON or OFF:
Controller with a power ON and OFF
3. OUTPUTS: 1 - 4 OUTPUT SELECTION:
Press the destination button to select the output display channel.
4. SOURCE : 1 thru 4 INPUT SOURCE SELECTION
Press input 1~4 sources with selection button
5. FUNCTION KEY
ALL - function selection button
OFF - function selection button
RECALL - function selection button
ENTER - function selection button
MEMORY - function selection button
LOCK - function selection button

8
REMOTE PROTOCOL COMMANDS
IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD)
HOW TO SETUP IR CODES : CUSTOM CODE : 20DF
POWER ON : 20DF A15E LOCK : 20DF B54A
POWER OFF : 20DF A25D RECALL : 20DF B24D
ALL : 20DF B04F ENTER : 20DF B34C
OFF : 20DF B14E MEMORY : 20DF B44B
PRESS TV DESTINATION - # then PRESS SOURCE - #
DESTINATION #1 : 20DF 01EF SOURCE #1 : 20DF 01FE
DESTINATION #2 : 20DF 02DF SOURCE #2 : 20DF 02FD
DESTINATION #3 : 20DF 03CF SOURCE #3 : 20DF 03FC
DESTINATION #4 : 20DF 04BF SOURCE #4 : 20DF 04FB
For example;
Select Destination # 1 to show Source #1~4,
The IR Data Code list when press Destination # then press Source #
Press Destination # 1 & Source #1 20DF 01EF 20DF 01FE
Press Destination # 1 & Source #2 20DF 01EF 20DF 02FD
Press Destination # 1 & Source #3 20DF 01EF 20DF 03FC
Press Destination # 1 & Source #4 20DF 01EF 20DF 04FB