Shinybow USA SB-5688 User manual

MULTIMEDIA AUDIO AND VISUAL
8x8 HDMI MATRIX SWITCHER
INSTRUCTION MANUAL
MODEL : SB-5688
8X8 HDMI MATRIX SWITCHER
HDMI Matrix Switcher Series
Thank you for purchasing the SB-5688 HDMI Matrix Switcher. You will nd this unit easy to install and highly
reliable but it is essential that you read this manual thoroughly before attempting to use 8x8 HDMI Matrix switcher.
Part No.: ENCL005688000A2

SAFETY INFORMATION
1. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
2. Read all documentation before operating your equipment. Retain all documentation for future reference.
3. Follow all instructions printed on unit chassis for proper operation.
4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
5. Make sure power outlets conform to the power requirements listed on the back of the unit.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
8. Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
9. Power down & disconnect unit from mains voltage before making connections.
10. Never hold a power switch in the “ON” position.
11. Do not use the unit near stoves, heat registers, radiators, or other heat Producing devices.
12. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
 owofairaroundtheunit,suchasabed,rug,carpet,orcompletelyenclosedrack.Iftheunitisusedinanextremelydustyorsmoky
environment, the unit should be periodically “blown free” of foreign matter.
13. Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no user serviceable parts
inside.
14. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
15. Non-use periods. The power cord of equipment should be unplugged from the outlet when left unused for a long period of time.
16. ServiceInformationEquipmentshouldbeservicedbyqualierservicepersonnelwhen:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
IMPORTANT SAFETY INSTRUCTIONS
To insure the best from this product, please read this manual carefully. Keep it in a safe place for future reference.
Toreducetheriskofelectricshock,donotremovethecoverfromtheunit.Nouserserviceablepartsinside.Referservicingtoqualiedpersonnel.
Toreducetheriskofre,donotexposetheunittorain,waterorexcessivemoisture.
Do not force switched or external connections.
Whenmovingtheunitdisconnecttheserialportconnectionsrstthenthepowercableandnallytheinterconnectingcablestootherdevices.
Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Use a clean dry cloth.
Installation of this unit should be in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS & INTRODUCTION
TABLE OF CONTENTS 3
INTRODUCTION AND PACKAGE OF CONTENTS 3
FEATURES AND SPECIFICATIONS 4
EDID FUNCTIONS 5
CEC FUNCTIONS 6
FRONT PANEL 7
FRONT PANEL - CONTROL FUNCTIONS 8
REAR PANEL 9
TYPICAL APPLICATION 10
REMOTE CONTROL 11
REMOTE CONTROL - DATA CODE LIST 11
IR EXTENDER 13
RS-232 SERIAL INTERFACE 14
RS-232 SERIAL COMMANDS 15
INTRODUCTION
The SB-5688 is high-performance 8x8 matrix routing switcher for HDMI signals. This switcher supports data rates up to 6.75 Gbps,
enabling 1080p HDMI formats and UXGA/WUXGA/DVI resolution to any HD display. High Denition Digital signals can be selected
anddistributedtoany8outputssimultaneously.TheSwitcheriscertiedasbeingfullyHDMIandHDCPcompliant,withRoHS,CE,FCC
certication.SupporthighresolutionHDMIsourcesroutedtoHDMIdisplays,monitors,projectororaudioreceivers.TheEDIDcanbe
selected between seven (7) different modes. Control is provided via Front panel push buttons, IR remote or via RS-232. An RS-232
Windows GUI interface is provided for matrix routing.
The SB-5688 is a 8x8 HDMI Matrix Switcher featuring 8 inputs and pre-emphasized 8 outputs. Full support HDMI / HDCP compliant.
8 inputs as following : 8 matrix outputs as following :
• 8xHDMI(DigitalVideo/Audio)   •8xHDMI(DigitalVideo-TMDS/DigitalAudio)
Support Seven Control Function Keys : ALL > OFF > PREV(RECALL) > PLAY/DEMO(ENTER) > SAVE(MEMORY) > EDID > LOCK
EDID support :
1. INTERNAL modes
○Auto
○1080P- 2C
○1080P- 5.1
○1080P-7.1
○1080i- 2CH
○720P- 2CH
2. EXTERNAL mode
PACKAGE CONTENTS
1. Main console unit
2. Operating Instructions
3. IR Remote Controller (SW-5688)
4. 19 inch Ear mount bracket (Part # 1U-440L)
5. IR Extender receiver (SB-100)
6. CD Contents: This manual, Windows GUI
7. RS-232 Cable
8.PowerSupply12VDC,3AUniversalType50/60Hz,100~230VACProductSpecications
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
This symbol is intended to alert the user to the presence of uninsulated of
uninsulated “dangerous voltage” within the products enclosure that enclosure
that may be of sufcient magnitude to constitute a risk of electric shock to
persons.
This symbol is intended to alert the user to the presence of important operational
and maintenance (serving) instructions in the literature accompanying the
appliance.
To prevent electric shock do not use this (polarized) plug with an extension cord,
receptacle or other outlet unless the blades can be fully inserted to prevent blade
exposure. To prevent electric shock, match wide blade of plug to wide slot, fully
insert.
3

FEATURES & SPECIFICATIONS
FEATURES
1. Support 8x HDMI digital source devices matrix switched to 8x HDMI devices.
2. HDMI digital video w/embedded audio, DVI format and HDCP compliant
3. Seven (7) function key control and worldwide EDID modes for HDTV resolutions.
4. Link speeds of up to 6.75 Gbps (link clock rate of 340Mb Hz), for 3D formats.
5. Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV resolutions 480i/480p, 576i/576p, 720p,
1080i & 1080p
6.CompatiblewithallHDMIsourcedevices,PCmonitors,PlasmaHDdisplay,HDTVandaudioreceivers/ampliers.
7. Digital Video TMDS formats
8. Support IR Remote and IR Extender with distance up to ~ 1000’ (300M) Maximum.
9. Various User Interface control:
• Windows based GUI control via RS-232 port
• Front Panel push button
• IR wireless remote control
• Third party RS-232 controller (via simple ASCII)
10. Front panel buttons: ALL/OFF/PREV/PLAY/SAVE/EDID/LOCK
11. Automatic scanning input & output status
12. Desktop with optional rack mount via included 19 inch bracket.
13.EDIDcongurationviaInternalmodes.
14. Consumer Electronic Control (CEC) switch all open or OFF
The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last conguration will be invoked.
SPECIFICATIONS
1. Type of Switcher : 8x HDMI inputs To 8x HDMI Outputs Matrix Switcher
2. HDMI Support : HD 1080P-@60Hz, H36-bit Deep color, 3D (1.4a) formats
3. HDCP / CEC Support : HDCP 2.0 Compliant, CEC Compliant
4. Video Bandwidth : Double Data Rates:225Mhz, Total 6.75Gbps bandwidth
5. Digital Video Support : Full HD resolution : 480p / 480p / 720p / 1080i / 1080p
6. Digital Audio Support : Multi Audio Formats 5.1 / 7.1, MAT(MLP) Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES 6.1,
DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
7. Controls : IR Remote Controller
IR External port x 1 (OD 3.5mm Ear phone Jack)
Select & Function buttons on front panel
RS-232 series interface
8. Source Status : Automatically Scan Sources Inputs via LED
9. Function Control Key : ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID
10. Infrared Frequency : 38 KHz
11. IR External Distance : ~1000 feet / 300 meters maximum
12. HDMI I/O Connector : HDMI Type A - SMD 19pin Female Type
13. Temperature : 32 F - 100 F Operation (0 C - 38 C)
14. Dimensions (LWH) : 19” x 9.85” x 1.75” *with rack mount
15. Rack Mount : Rack Mount 1RU High 19 ”Rack Mount (with rack mount)
16. Power Supply : DC12V / 5A, Universal world wide Type 50/60Hz, 100~230 VAC
17. Power Consumption : 3880 mA Maximum
18. Safety Approvals : CE, FCC, RoHS (2002/95/EC)
19. Product Weight : 2.50 Kgs / 4.2 lb
As product improvement is continuous, specications are subject to change and without notice or liability.
4

5
EDID FUNCTION
EDID function for HDMI Matrix Switcher
EDID Status To view the current EDID status
Step 1 . Press EDID button ThebuttonwillashblueandthedisplaywillshowthecurrentEDID Status.
Step 2 . Press EDID button to exit.
EDID Setup To change the EDID setup
Step 1 . Press EDID button Thebuttonwillashblueandthedisplaywillshow
the current EDID Status.
Step 2 . Press Input source #1 or #2 button row to select EDID mode.
Repeatedly depressing the source 1button will cycle up thru the options.
Repeatedly depressing the source 2button will cycle down thru the options.
Options are :
Auto <Default> All Outputs will be set to the highest common resolution of all connected display devices.
1080p/2CH PCM 2CH, AC-3 2CH
1080p/ 5.1 PCM 2CH, PCM 5.1CH, AC-3 5.1CH, DTS 5.1CH, One Bit Audio 5.1CH, Dolby Digital+5.1CH, DTS HD
5.1CH, Multi Audio Format 5.1CH, 36Bit 3D
1080p/7.1 PCM 2CH, PCM 7.1CH, AC-3 7.1CH, DTS 7.1CH, One Bit Audio 7.1CH, Dolby Digital+7.1CH, DTS HD
7.1CH, Multi Audio Format 7.1CH, 36Bit 3D
1080i/2CH PCM 2CH
720p/2CH PCM 2CH
EXTERNAL(EtL) Passing Source To Source Via Learning Destination EDID link to Input Source.
Step 3 . Press the ENTER button To set EDID mode.
The switcher will return to operation mode.
Auto Mode Denition Common Resolution and Audio
SwitcherwillndhighestcommonResolutionandAudiofromalldestinationEDIDtolinkSource.
Example for single source
Destination > press #1 and then Source > press #1
Destination device #1 will set to the highest common resolution and Audio of source #1
Example for multiple sources
Destination device #1, #2, #3 will be set to the highest common resolution and Audio available and source device #1 will output
this same resolution.

CONSUMER ELECTRONICS CONTROL (CEC)
CONSUMER ELECTRONIC CONTROL (CEC)
In brief, CEC allows HDMI devices to control each other when necessary and allows the user to operate multiple devices
with one remote control handset.
To Enable CEC
- Press EDID button
- Press ALL button
- Press EDIDbuttonThepre-setcongurationwillexecute.
To Disable CEC
- Press EDID button
- Press OFF button
- Press EDIDbuttonThepre-setcongurationwillexecute.
Not all device support CEC. Check with your Users Guide for additional information and specifications.
To ensure stable operation, HDMI connections should only be made with switcher powered OFF.
6

7
FRONT PANEL
FRONT PANEL
1 POWER SWITCH
The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power.
TheSwitcherwillrememberthatlaststateduringapowercycle.Whenpowerisremovedandresorted,thelastcongurationwillbeevoked.
2INPUT STATUS DISPLAY
Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input.
3 OUTPUT STATUS DISPLAY
Each Output (destination) Channel shows which input (source) is assigned.
4 DESTINATION SELECT BUTTONS
Separate outputs 1 thru 8 select buttons are provided for each destination assignment. Routing can be Source to Destination or one
source to multiple destinations.
Example : Press Destination 1,3,5 then press Source 2 will route Input 2 to Output 1,3,5 respectfully.
5 EDID MODE SELECT BUTTONS
Used to select EDID mode using buttons 1 thru 7
6 IR SENSOR
The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
7 SOURCE SELECT BUTTONS
Separate inputs 1 thru 8 select buttons are provided each source selection.
8 FUNCTION KEY - ALL
Disables (mute) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video
selected.
Option 2
- Press ALL followed by Source 1 thru 8. The display will show the Source selected.
- Press PLAY The pre-set source selection will be assigned all destinations.

8
FRONT PANEL
FRONT PANEL
9 FUNCTION KEY - OFF
Disables (mute) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 8 output destination. The display will show “ 0 “ for the selected channel indicating no video selected.
10 FUNCTION KEY - PREV
The system will show previously stored presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
-Conguredesiredmatrices.
- Press PREV button.
- Press 1 thru 8 on either Source or Destination row.
- Press PLAYThepre-setcongurationwillexecute.
Operation completes.
Operation will abort if no keys are pressed with 5 seconds.
11 FUNCTION KEY - PLAY
The system will execute a previously stored preset.
- Press ALL, OFF or PREV button.
- Press 1 thru 8 on either Source or Destination row.
- Press PLAYThepre-setcongurationwillexecute.
12 FUNCTION KEY - SAVE
ThesystemwillSAVEcurrentcongurationintomemory.
- Press SAVE to store memory location.
- Press 1 thru 8 on either Source or Destination row.
13 FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
14 FUNCTION KEY - EDID
- Press EDID to select new EDID mode or select destination row 1 thru 8 for LINK source EDID again.
-PressPLAYThepre-setcongurationwillexecute.
15 19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount. Bracket (part # 1U-440L) INCLUDED.
Image shows rack mount bracket attached.

9
REAR PANEL
REAR PANEL
1 DC POWER INLET
TheSwitcheristtedwithaDCpowerpluginputconnector.
Ensurethattheusedisofanapprovedtypeandisofsufcient
current carrying connector capacity with the correct voltage and
connector polarity. 12Volt DC power supply 4A Max (Center pin positive).
2IR EXTENDER CONTROL
Support one of IR Extender
Extend distance maximum 300Meters / ~1000 feet
When you plug the External IR extender into the switcher, the front
panel IR receiver remain active.
3RS-232 CONNECTION
RS-232 control port to allow for interfacing to a PC, Such as a
computer or touch panel control, to the switcher via this DB-9pin
Female connector for serial RS-232 control.
4INPUTS- 1,2,3,4,5,6,7, & 8 HDMI
Connect a signal link of HDMI direct digital video/audio to this
Female HDMI connector. This connector supports HDMI digital
video/audio and DVI digital video sources.
HDMIDigitalVideo/Audio,ConnectorwithxscrewInput1~Input8
5 OUTPUTS- 1,2,3,4,5,6,7 & 8 HDMI
Connect a signal link of HDMI direct digital video/audio to this
Female HDMI connector. This connector supports HDMI digital
video/audio and DVI digital video sources.
HDMIDigitalVideo/Audio,ConnectorwithxscrewOutput1~Output8
Power Jack:
DC Jack - Inner OD O 2.1mm (+ )
Outside OD O 5.5mm (GND)
Power input - 12VDC, 2A
IR Extender Jack:
Female Jack - inner OD O 3.5 mm
Remote port :
DB-9pin Female connector
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the
switcher can be used with DVI digital
video signals HDCP compliant. DVI does
not support audio.
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the
switcher can be used with DVI digital
video signals HDCP compliant.

TYPICAL APPLICATION
INSTALLING DIAGRAM
8x8 HDMI MATRIX SWITCHER SB-5688
CONNECTION PORTS:
CONTROL PORTS :
1. IR EXTEND - External IR receiver
2. RS-232 - PC RS-232 Series port
INPUTS PORT SIGNALS :
1. HDMI (HDCP Compliant) 5. HDMI (HDCP Compliant)
2. HDMI (HDCP Compliant) 6. HDMI (HDCP Compliant)
3. HDMI (HDCP Compliant) 7. HDMI (HDCP Compliant)
4. HDMI (HDCP Compliant) 8. HDMI (HDCP Compliant)
OUTPUT PORT SIGNALS :
1. HDMI (HDCP Compliant) 5. HDMI (HDCP Compliant)
2. HDMI (HDCP Compliant) 6. HDMI (HDCP Compliant)
3. HDMI (HDCP Compliant) 7. HDMI (HDCP Compliant)
4. HDMI (HDCP Compliant) 8. HDMI (HDCP Compliant)
DC POWER INPUT :
SUPPORT DC12V POWER INPUT
SB-5688 SUPPORT EIGHT HDMI INPUTS TO EIGHT HDMI MATRIX OUTPUTS
SUPPORT IR EXTENDER & RS-232 CONTROLS.
10

REMOTE CONTROL
Before making any connections to the switcher. Observe the following:
> Ensure the mains voltage supply matches the label on the
supplied plug-pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a
common point.
> Avoid powering equipment within a system from multiple power
sources that may be separated by large distances
> Connect all audio video sources and destination equipment
> Power up all source and destination audio-visual sources
> For each destination output select the appropriate input source
by using the front panel input 1~8 select buttons. The supplied
IR remote control. Or through the RS-232 serial communications
port.
> Upon power up the switcher will return to its last used setting
before powered down.
REMOTE CONTROL
IR REMOTE : SW-5688
IR REMOTE CONTROL KEY :
1 2 SWITCH 1 POWER ON or OFF
Controller with a separate power ON and OFF
3DESTINATION : 1 thru 8 OUTPUT SELECTION
Press the destination button to select the output display channel.
4FUNCTION KEY
ALL - function selection button
ENTER - function selection button
EDID - function selection button
LOCK - function selection button
5SOURCE : 1 thru 8 INPUT SOURCE SELECTION
Press input 1~8 sources with selection button
IR REMOTE CUSTOM AND DATA CODES (NEC Standard)
HOW TO SETUP IR CODES :
CUSTOM CODE : 09F6 ALL : 09F6 B04F
POWER ON : 09F6 A15E ENTER : 09F6 B34C
POWER OFF : 09F6 A25D EDID : 09F6 B748
LOCK : 09F6 B54A
PRESS DESTINATION - # then PRESS SOURCE - #
DESTINATION #1 : 09F6 10EF SOURCE #1 : 09F6 01FE
DESTINATION #2 : 09F6 20DF SOURCE #2 : 09F6 02FD
DESTINATION #3 : 09F6 30CF SOURCE #3 : 09F6 03FC
DESTINATION #4 : 09F6 40BF SOURCE #4 : 09F6 04FB
DESTINATION #5 : 09F6 50AF SOURCE #5 : 09F6 05FA
DESTINATION #6 : 09F6 609F SOURCE #6 : 09F6 06F9
DESTINATION #7 : 09F6 708F SOURCE #7 : 09F6 07F8
DESTINATION #8 : 09F6 807F SOURCE #8 : 09F6 08F7
11

IR EXTENDER
REAR PANEL IR EXTENDER PORT
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
IR EXTENDER PACKAGE :
HOW TO SETUP THE IR EXTENDER COMPONENTS
12

RS-232 SERIAL INTERFACE
RS-232 SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM. VERSION-1.0 COMPATIBLE
RS-232 SERIAL INTERFACE
Pin RS-232 Denition
1 -------- Not used
2 TX Transmitter
3 RX Receiver
4 -------- Not used
5 GND Ground
6 -------- Not used
7 -------- Not used
8 -------- Not used
9 -------- Not used
RS-232
The SHINYBOWUSA switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party
control system.
The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1. When the
unit recognizes a complete command it will perform the requested action - there is no delimiter character required.
The unit does not send out a message when a value is changed from the front panel or by IR control. If the unit needs to be controlled
via the front panel in addition to the RS-232 control, you should regularly poll the unit status to ensure the control system accurately
 reectsthecurrentsettings.
PROTOCOL COMMANDS
Several of the most common commands are listed below.
For a complete list of commands, please reference external document “Extended RS-232 Protocol and Commands”.
To Switch Inputs to Outputs
SBI0XO0Y - Where X is Input Number (1-8) and Y is Output Number (1-8)
Unit will respond with
SBUD0XOY - Where X is Input Number (1-8) and Y is Output Number (1-8)
Example : Send Input 8 to Output 7
SBI08O07 - Send
SBUD08O7 - Rcvd
13
15
69

RS-232 SERIAL COMMANDS
MORE STUFF
Note: Turning the unit System Power Off via RS-232 will extinguish the LED channel display leaving only the Power Switch
LED on. The Video and Audio outputs will also mute. While the unit is turned off by RS-232 it will continue to accept and
act upon switching commands. For example, if the unit is in the off mode (via RS-232) and you send a command
to switch an input to an output, that route will complete and the video and audio will now appear on that channel only.
The front panel LED channel display for that particular output will also show the input selected (for that single output
channel only). The remaining LED’s will remain off and video and audio outputs muted. The unit will still return status
and change messages in response to commands sent while in Power Off state. A hard reset command (SBALLRST)
will return the unit to normal operation and also unlock the front panel.
Power Off mode.
SBSYSMOF - Put system into Standby (Soft Power Off)
SBSYSMON - Bring unit out of Standby (Soft Power On)
Unit will respond with
SBALOFAK - Unit is in Standby
SBALONAK - Unit is no longer in Standby
Example : Put Unit in Standby (Soft Power)
SBSYSMOF - Send
SBALOFAK - Rcvd
FRONT PANEL LOCK
Note: Hard resetting the unit will unlock the Front Panel controls.
SBSYSMLK - When front panel is locked, changes can only be made by RS-232
SBSYSMUK - Front Panel Unlock
Unit will respond with
SBSYSLOK - Front Panel has been Locked
SBSYSULK - Front Panel has been Unlocked
Example : Lock Front Panel Buttons
SBSYSMLK - Send
SBSYSLOK - Rcvd
UNIT RESET
SBALLRST - Reset every output to Input 1
Unit will respond with
SBRSTACK - Unit has reset each Output to Input 1
Example : Reset all outputs to Input 1
SBALLRST - Send
SBRSTACK - Rcvd
14

15
LIMITED WARRANTY
LIMITED WARRANTY
SHINYBOWUSA WARRANTY
SHINYBOWUSA Technology warrants this product against defects in materials and workman ship for a period of 3 year from
the date of purchase.
Should this product, in SHINYBOWUSA Technology’s opinion, Prove defective within this warranty period, SHINYBOWUSA
Technology, at its option, will repair this product without charge, to whatever extent it shall deem necessary to restore said
product to proper operation condition. This does not extend the warranty period.
This warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse,
andabnormaloperatingconditionornon-SHINYBOWUSATechnologyauthorizedmodicationtotheproduct.
If repairs are necessary under the warranty policy, the original purchaser must return the product to local distributor, freight
prepaid.
After repairs are complete, the product will be returned.
REGULATORY COMPLIANCE
The product complies with the relevant standards for CE, FCC and RoHS approval.
The power Adaptor/Supply has been tested for compliance with UL.CSA and CE standards.
TROUBLESHOOTING
Ifyouexperiencea<nosignal>withthisswitcherordistributoroutputs,rstmakecertainthatthesignalbeingfedtoitsinputs
is acceptable.
Disconnect the cables from the this switcher or distributor inputs and connect them directly to an appropriate monitoring device,
if you do not see or hear a signal the problem may well be he signal source itself. Also check that the AC outlet you have used
to power the switcher or distributor is actually providing power as a wall switch often controls an AC outlet.
The second most common problem with this switcher or distributor revolves around the cables, Inspect the cables for loose
connectors or cable damage such as crushed cable or cables with cuts or nicks. Replace any cable exhibiting these problem.
You also must use the highest quality cables if you want to achieve the best results. Poor quality cables provide will poor quality
signals.

www.shinybowusa.com
1399WildreLane|Frisco,TX75034
1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 [email protected]
MULTIMEDIA AUDIO AND VISUAL