Shinybow USA SB-5564LCM User manual

SB-5564LCM
6x4 COMPONENT-AUDIO MATRIX SWITCHER
INSTRUCTION MANUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

1
CONTENTS
INTRODUCTION ..............................................................1
FEATURES & SPECIFICATIONS ....................................2
FRONT PANEL ................................................................3
BACK PANEL ...................................................................6
REMOTE CONTROL .......................................................7
IR EXTENDER ................................................................9
RS-232 SERIAL INTERFACE ......................................10
TYPICAL APPLICATION ...............................................11
INTRODUCTION
Congratulations on your purchase of one of the most innovative
Component Video/Audio matrix switching products on the market
today. The SB-5564LCM is a true matrix routing switcher for
Component Video and Stereo Audio signals. It has (6) individual
Component inputs with (4) individual Component outputs.
Because it is a matrix router, any input may be routed to any
output; or the same input may be routed to all outputs or any
combination. It completely eliminates the need to constantly
move around audio and video input and output cables. The SB-
5564LCM is useful for matrix signals from AV source devices
(such as: VCRs, Camcorders, Video Game Consoles, Video
CDs, DVDs, Satellite Receivers, CAT5 Set Top Boxes, etc.) to AV
destination devices (such as: LCD TV, HDTV, Plasma displays,
Projectors, etc.). Selection of inputs is made via the front panel
push buttons or an infrared remote control or with RS-232 control
by a computer.
PACKAGE CONTENTS
Check that you have the following components;
• SB-5564LCM Matrix Switch
• IR Remote Control (SW-5564)
• 19 inch ear mount bracket (Part # 1U-440L, 1RU(1½”))
• SB-100 IR Extender Receiver Set
• CD Contents: This manual, Windows GUI
• RS-232 Cable
• Users Guide
• Power Supply 12VDC, 2A Universal Type 50/60Hz, 100~230VAC
• Optional:SB-100CIRExtenderReceiverCable(6.5ft(2M))
Component Video-Stereo Audio Matrix Switcher Series
ThankyouforpurchasingtheSB-5564LCM6x4ComponentVideo-AudioMatrixSwitcher.Youwillndthisuniteasytoinstallandhighly
reliablebut itisessentialthatyouread thismanualthoroughlybeforeattemptingto usethe6x4ComponentVideoandAudio Matrix
Switcher.
TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise — without express written permission and consent.
© Copyright 2017. All Rights Reserved.
Version 2.3 SEPT 2017
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.

2
FEATURES
• (6) Inputs to (4) Outputs Component Video (YPBPR) Matrix Switcher
• Input/Output signals via Component Video (YPBPR), Stereo Audio (AR/AL)
• Higher video bandwidth 325MB each path signals
• Supports HDTV high denition resolutions 480p, 576i/p, 720p, 1080i/1080p
• Compatible with all Component Video devices, Plasma TV displays and HDTVs
• Supports RS-232 serial interface protocol command list
• PC RS-232 control drive compatible with Win-95/98/2000/XP
• Various User Interface Controls:
• Included Windows based control software for Desktop or NB control via the RS-232 port
• Manual control via front panel buttons
• IR remote control
• Supports desktop with ear mount and 19 inch rack mountable type panel
• Power supply DC12Volt, Universal type switch 100~230VAC, 50/60Hz
SPECIFICATIONS
• Type of Switcher: (6) In to (4) Out, Component Video-Audio Matrix Switcher
• I/O Signals:
• Component video (YPBPR) 0.5~1.0Vpp, DDC 5Vpp
• Higher resolution formats 480i/p, 720p & 1080i/p
• Video Bandwidth: 325MHz (-3dB), 200mVpp
• Video Supported: Higher resolution formats 480i/p, 720p & 1080i/p
• Audio Supported: Stereo Audio (AR/AL)
• Low All Hostile Crosstalk: -83dB@5MHz
• Controls: IR remote, Select buttons on the front panel & RS-232
• PC RS-232 Control: RS-232 interface serial via DRV on a PC
• Gain Control: 60MHz 0.1dB gain atness
• Chassis Material: Metal
• Dimensions (WxDxH): 17.5 x 8 x 1.75 in
• Weight: 5.5 lb (Unit only) / 7.9 lb (Net)
• Safety Approvals: CE, FCC, RoHS (2002/95/EC)
• Power Supply: DC12V / 2A (consumption 1.6A Max) Uses universal switch type 50/60Hz, 100~230 VAC
As product improvements are continuous, specications are subject to change and without notice.
FEATURES & SPECIFICATIONS

3
FRONT PANEL
FRONT PANEL
1. POWER ON SWITCH: The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is
receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last conguration
will be evoked.
2. INPUT STATUS DISPLAY: Input sources 1 to 6 LEDs illuminate blue to indicate that a video source is present on that input.
3. OUTPUT STATUS LCM DISPLAY: Each output (destination) channel shows which input (source) is assigned.
4. DESTINATION SELECT BUTTONS: Separate outputs 1 thru 4 select buttons are provided for each destination assignment. Routing can be
Source to Destination or one source to multiple destinations.
Example: Press Destination 1, 3, 4 then press Source 2 will route Input 2 to Output 1, 3, 4 respectfully.
5. SOURCE SELECT BUTTONS: Separate inputs 1 thru 6 select buttons are provided each source selection.
6. IR SENSOR: The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
OPERATING THE UNIT
Once you have connected the SB-5564 as described above, you must be certain that the inputs are being fed to the appropriate signals
and are not suffering from signal loss due to cabling problems or problems with the source device.
If the input signals to the SB-5564 are appropriate, switch the power switch to <ON> and you should see and hear the signals on the
devices you have connected to the various output connectors of the SB-5564.
POWER AND CONNECTIONS
This unit is not disconnected from the AC power source as long as it is connected to the wall outlet. The off state for this unit is called
standby mode. In standby mode the unit is designed to consume a reduced quantity of power compared to normal operating modes.
When not using the unit for a long period of time. Insure that the AC power cord is disconnected from the wall outlet.
The AC wall outlet should be installed near to the unit and be easily accessible.
Do not plug in or attempt to operate an obviously damaged unit.
CONNECTING THE HARDWARE
Please study the panel drawings and become familiar with the signal input-output power requirements plus any controls present.
Before using the switcher, please take the time to make certain that the device you wish to connect to its inputs is functioning properly in
all respects. Verify that the video and audio signals are present and are being displayed properly on a suitable device.
If all is well, connect the appropriate cables between the output of the device you wish to distribute to output(s) of the switcher to the
carious devices you wish to feed a signal to. Lastly, connect the AC to DC adaptor, connect the DC connector to the switcher rst and then
plug the adaptor into a functional AC outlet.

4
FRONT PANEL
FRONT PANEL
8. FUNCTION KEY - ALL:
Disables (mutes) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show “0“ indicating all destinations
have no video selected.
Option 2
- Press ALL followed by Source 1 THRU 6. The display will show the Source selected.
- Press ENTER. The pre-set source selection will be assigned all destinations.
9. FUNCTION KEY - OFF:
Disables (mutes) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press 1 THRU 4 output destination. The display will show “0“ for the selected channel
indicating no video selected.
10. FUNCTION KEY - RECALL:
The system will show previously stored presets, up to a total of 10. Presets are stored in
local memory using Source keys 1 thru 6 or Destination keys 1 thru 4 as the memory preset
location.
- Press RECALL button.
- Press 1 THRU 6 on either Source or 1 THRU 4 Destination row.
- Press ENTER. The pre-set conguration will execute.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.
11. FUNCTION KEY - ENTER: Press ENTER to conrm entries.

5
FRONT PANEL
FRONT PANEL
12. FUNCTION KEY - MEMORY:
The system will show stored presets, up to a total of 10. Presets are stored in local memory
using Source keys 1 thru 6 or Destination keys 1 thru 4 as the memory preset location.
- Congure desired matrices.
- Press MEMORY button.
- Press 1 THRU 6 on Source or 1 THRU 4 on Destination row.
- Press ENTER to ready memory location.
- Or press MEMORY again to cancel operation.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.
13. FUNCTION KEY - LOCK:
- Press and hold LOCK button for two seconds to lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
14. 19 INCH EAR MOUNT PAIR: Converts desktop to 19 inch rack mount. Bracket (part # 1U-440L) INCLUDED. Image shows rack mount
bracket attached.

6
BACK PANEL
BACK PANEL
1. DC POWER INLET: The switcher is tted with a DC power plug-park
input connector. Please ensure that the plug-park used is of an
approved type and is of sufcient current carrying capacity with
the correct voltage and connector polarity. 12Volt DC power supply
2A Max.
2. RS-232 CONNECTION: RS-232 control port allows for interfacing to
a PC, such as a computer or touch panel control, to the switcher via
this DB-9pin female connector for serial RS-232 control.
3. INPUTS-1~6 COMPONENT-DIGITAL-AUDIO: Connects a Component
Video (YPBPR)/Digital Audio (PCM)/Stereo Audio signal source
device to the switcher.
Input 1~6 port source signals:
- Component Video (YPBPR), (3) RCA Connectors
- Stereo Audio (AR/AL), (2) RCA Connectors
4. OUTPUTS-1~4 COMPONENT-DIGITAL-AUDIO: Connects a Component
Video (YPBPR), Digital Video & Audio signal direct to the female
RCA connector. This connector supports component video & stereo
audio to HDTV display devices.
Output 1~4 display port signals:
- Component Video (YPBPR), (3) RCA Connectors
- Stereo Audio (AR/AL), (2) RCA Connectors
POWER JACK:
DC Jack - Inner OD Ø 2.1mm (+)
Outside OD Ø 5.5mm (GND)
Power input -12VDC, 2A
REMOTE PORT : DB-9pin female connector
Component Video (YPbPr) via (3) RCAs
Stereo Audio (AR/AL) via (2) RCA connectors
Note: With (5) RCA female connectors.
Component Video (YPbPr) via (3) RCAs
Stereo Audio (AR/AL) via (2) RCA connectors
Note: With (5) RCA female connectors.

7
REMOTE CONTROL
Before making any connections to the SB-5564LCM Observe the following:
• Ensure the main voltage supply matches the label on the supplied plug-pack (+/-10%).
• Ensure that the power switch is OFF.
• Ensure that all system grounds (earth) are connected to a common point.
• Avoid powering equipment within a system from multiple power sources that may be separated by large distances.
• Connect all audio video sources and destination equipment.
• Power up all source and destination audio-visual sources.
• For each destination output select the appropriate input source by using the front panel input select buttons. The supplied IR remote
control. Or through the RS-232 serial communications port.
• Upon powering up the switcher, it will return to its last used setting before being powered down.
REMOTE CONTROL
IR REMOTE : SW-5564
IR PCB : RA-02
IR CUSTOM CODE: 24DB
1./2. SWITCH POWER ON or OFF: Power ON and OFF
3. DESTINATION : 1 thru 4 OUTPUT SELECTION:
Destination button to select the output display channel
4. SOURCE : 1 thru 6 INPUT SOURCE SELECTION:
Input 1~8 source selection buttons
5. FUNCTION KEYS: Function selection buttons
ALL OFF RECALL
DEMO or ENTER MEMORY LOCK

8
REMOTE PROTOCOL COMMANDS
IR REMOTE CUSTOM AND DATA CODES (NEC Standard)
HOW TO SETUP IR CODES :
CUSTOM CODE : 24DB
POWER ON: 24DB A15E LOCK: 24DB B54A
POWER OFF: 24DB A25D RECALL: 24DB B24D
ALL: 24DB B04F MEMORY: 24DB B44B
OFF: 24DB B14E ENTER: 24DB B34C
PRESS DESTINATION - # then PRESS SOURCE - #
DESTINATION #1 : 24DB 10EF SOURCE #1 : 24DB 01FE
DESTINATION #2 : 24DB 20DF SOURCE #2 : 24DB 02FD
DESTINATION #3 : 24DB 30CF SOURCE #3 : 24DB 03FC
DESTINATION #4 : 24DB 40BF SOURCE #4 : 24DB 04FB
SOURCE #5 : 24DB 05FA
SOURCE #6 : 24DB 06F9
For Example:
Select Destination # 1 to show Source #1~6,
The IR Data Code list when press Destination # then press Source #
Press Destination # 1 & Source #1 24DB 10EF 24DB 01FE
Press Destination # 1 & Source #2 24DB 10EF 24DB 02FD
Press Destination # 1 & Source #3 24DB 10EF 24DB 03FC
Press Destination # 1 & Source #4 24DB 10EF 24DB 04FB
Press Destination # 1 & Source #5 24DB 10EF 24DB 05FA
Press Destination # 1 & Source #6 24DB 10EF 24DB 06F9