Shinybow USA SB-5669CK User manual

INSTRUCTION MANUAL
MODEL : SB-5669CK
16x16 HDMI & HDBaseT 4K2K MATRIX ROUTING SWITCHER
16x16 HDMI & HDBaseT 4K2K Over Single CAT5e/6/7
Matrix Routing Switch
HDMI-HDBaseT 4k2k Matrix Routing Switch Series
Thank you for purchasing the SB-5669CK HDMI-HDBaseT Matrix Switcher. You will find this unit easy to install
and highly reliable but it is essential that you read this manual thoroughly before attempting to use 16x16 HDMI-
HDBaseT Matrix switcher.
MULTIMEDIA AUDIO AND VISUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF AGENERAL NATUREAND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for sufficient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed,stored in aretrieval system,or anyof itspart translated
into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 1997. All Rights Reserved.
Version 3.2 MAY 2014
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
CONTENTS
INTRODUCTION ...............................................................1
PACKAGECONTENTS .....................................................2
FEATURES ....................................................................... 3
SPECIFICATIONS ............................................................ 4
FRONT PANEL ................................................................ 5
REAR PANEL ................................................................ 9
HDBaseT I/O TRANSMISSION & CABLE EXTENSION
LENGTHS ....................................................................... 13
REMOTECONTROL.......................................................14
EDID FUNCTIONS ......................................................... 21
TYPICAL APPLICATION ............................................... 26
IR EXTENDER ............................................................... 30
ETHERNET PROTOCOL ............................................. 32
RS-232 PROTOCOL .................................................... 33
LIMITED WARRANTY .................................................. 34
INTRODUCTION
The SB-5669CK is professional 16x16 matrix routing switch.
Supporting sixteen (16) HDMI Inputs and sixteen (16) HDMI
Outputs & sixteen (16) HDBaseT Outputs. The SB-5669CK is
basedon the HDBaseTstandard and supports full resolution HDMI
Video with embedded HDCP, RS-232 and Bi-directional IR. All
over a single CAT6/6a/7 category cable. With a signal bandwidth
of 340Mhz, there is no signal degradation. High Definition Digital
signals can be selected and distributed to any 16 Inputs to 32
Outputs simultaneously (channel outputs mirrored). The Switcher
is certified as being fully CEC and HDCP 2.0 compliant, HDMI
4K2K V1.4a 3D formats, data rates up to 6.75 Gbps. Supports
UXGA/WUXGA/DVI1920x1200resolution toany HDdisplays.The
SB-5669CK has 16x HDMI connector Input and 16x HDBaseT &
16xHDMI output, effectively making this an 16 in x32 out switcher
(same signal on both outputs). Using the HDBaseT output remote
Transmitter allows you to connect a source in a remote location.
Likewise, the HDBaseT Output and our HDBaseT Receiver allows
you to connect a display in a remote location. EDID management
can be selected between seven (7) different modes. Control is
provided via front panel push buttons, IR remote, RS-232 or TCP/
IP (not a web-browser). An RS-232 Windows GUI interface is
provided for matrix routing control (Windows only).
1

PACKAGE CONTENTS
PACKAGE CONTENTS
Check that you have the following components;
• SB-5688CK Matrix Switcher
• Master wireless IR Remote Control (SW-5669)
• 16 each; Individual wireless IR Control (HD-69CK-IR01~IR16)
• 19 inch Ear mount bracket (Part # 4U-440L)
• SB-101 IR Extender distance ~984 feet (300M) Transmitter set.
• SB-100 IR Extender distance ~984 feet (300M) Receiver set.
• SB-101C IR Extender distance 6.50 feet (2M) Transmitter Cable.
• SB-100C IR Extender distance 6.50 feet (2M) Receiver Cable.
• CD Contents : This manual, Windows GUI, ISP V1.0 Windows driver
• RS-232 Cable 6.50 feet (2M)
• ISO Screws
• Users Guide
• (1) switcher (Version No.: 5669CK-20131220-001)
• (2) Ethernet V2.0 Protocol Instructions
• (3) RS-232 V2.0 Protocol Instructions
• Worldwide Universal Power Supply 100~240 VAC, AC 50/60Hz, 10A.
-- SB-6335R HDBaseT Receiver sold separately –
2

FEATURES
FEATURES
Based on HDBaseT; bi-directional IR and RS-232 interface. Full resolution HD Video, all HDBaseT signals over single category cable
(CAT6/6a/7).
• Enables switching of (16)x HDMI digital source devices to (16)x HDMI devices and (16)x HDBaseT
• Transmitter output to (32)x destinations
• Application HDBaseT Specification with Bi-Directional IR, RS-232, Multi Audio Format and HD
• Video Signals over single CATx (6/6a/7) category cable
• HDMI digital Video w/embedded HDCP, DVI format and CEC/HDCP 2.0 compliant
• Worldwide control EDID modes for HDMI full 4K2K HD Video resolutions
• Link speeds of up to 6.75 Gbps (link clock rate of 340MbHz), Support HDMI 4K2K, 1.4a 3D formats
• Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV HDMI resolutions 480i/480p, 576i/576p, 720p,
1080i/p & 4K2K
• Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV and audio receivers or audio amplifiers
• Digital Video TMDS formats Resolution up to 4K2K with Deep color 36-bit
• Digital Audio Support digital multi-channel Audio :
• Dolby TrueHD,
• Dolby Digital,
• Dolby Digital Plug/ex,
• DTS,
• DTS-HD,
• DTS-HD Master,
• DTS-EX
• PCM,
• PCM2,
• LPCM2
• HDBaseT Support IR Remote and RS-232 signals over single one CATx (6/6a/7) category cable.
• Various User Interface controls:
• Windows based GUI control via RS-232 port
• Front Panel push button
• IR wireless remote controller
• Ethernet Switch control
• Third party RS-232 controller (via simple ASCII)
• Support world wide (7)x control function keys:
• Full function front panel controls : ALL / OFF / EDID / LOCK / RECALL / MEMORY / ENTER
• Support EDID modes :
• a. Embedded EDID modes : FSS (fast speed start ) / H24-3D/ H24-3D-M/ H36-3D/ H36-3D-M/ 4K2K-3D / DVI-D 1920x1200-60Hz
• b. External modes : Learning mode (learning destination EDID link to source device).
• Automatic scanning input & output status via LCM show on front panel.
• Support IR Remote and IR Extender with distance up to ~ 984 feet (300 meters) Maximum.
• Support Universal power adaptor AC100V~AC240V, 50/60Hz.
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be invoked.
3

SPECIFICATIONS
SPECIFICATIONS
• Type of HDMI Switcher: 16x HDMI inputs To 16x HDMI & 16x HDBaseT Outputs Matrix Switcher.
• HDMI Support: HDMI 4K2K, 1080p-@60Hz, H36-bit Deep color, 3D of HDMI V1.4 formats
• HDBaseT Support: HDMI digital signals, bi-directional IR and RS-232 over single CATx(6/6a/7) cable
• HDCP / CEC Support: HDCP 2.0 Compliant, CEC Compliant
• Video Bandwidth: Double Data Rates: 340 MHz, total 6.7 Gbps bandwidth
• Digital Video Support: HD:480i/ 480p/ 720p/ 1080i/p and 4K2K up to 36bit deep color
• Inputs: HDMI: 16x HDMI (HDMI or DVI digital source).
• Outputs:
• HDMI: 16x HDMI (To Destination)
• HDBaseT: 16x HDBaseT Transmitter via single category cable use RJ-45 connectors
• HDMI digital multi-channel audio support : Multi Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD,
Dolby Digital Plus, DTS, DTS-ES 6CH, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• HDBaseT Out:
• IR Control:
• 16x IR in (Send IR signals To 16x Rooms via HDBaseT Transmitter)
• 1x ALL IR in (Send IR Signals To 16x Rooms - Via HDBaseT Transmitter)
• 16x IR out (Link to Receive IR signals from 16x Rooms via HDBaseT Extender)
• 1x ALL IR out (Link to Receive IR signals from 16x Rooms via HDBaseT Extender)
• RS-232 I/O Control:
• 16x RS-232 I/O (Control 16x Rooms RS-232 via Switcher HDBaseT Extender Tx)
• Switcher Controls:
• 1x Select & Function buttons on front panel (Data status via LCM panel show out)
• 1x IR Remote Controller (switch control), p/n: SW-HD69CK
• 16x IR Room Remote Controller (switch control), p/n: SW-HD69CK01~16
• 1x IR External port (switch control via 3.5mm OD Jack)
• 1x RS-232 series interface (switch control)
• 1x Ethernet series interface (switch control)
• Source Status: Input status LEDs indicates presence of a live signal
• (39) Function Control Key: ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID / Destination 1 thru 16 / Source 1 thru 16
• (7) EDID Management:
• Select Embedded EDID modes :
• Mode1: Fast Speed Start®
• Mode2: H24-3D
• Mode3: H24-3D-M
• Mode4: H36-3D
• Mode5: H36-3D-M
• Mode6: 4K2K-3D, PCM-2CH
• Mode7: DVI-D 1920x1200
• Select LEARNING mode : Learning Destination EDID To Link Source
• Infrared Frequency: 38 Khz
• IR Extend Distance: SB-100(~984 ft / 300 M maximum), SB-100C (~6.5 ft/ 2 M)
• HDBaseT Extender Distance: ~328 feet / 100 meters maximum.
• HDMI I/O Connector: HDMI Type A - SMD 19-pin female type
• Temperature: Operate in a place between 32°F - 100°F (0°C - 38°C)
• Dimensions (LxWxH): 17.32 x 11.81 x 5.19 in (442mm x 300mm x 176mm)
• Rack Mount: 4RU High 19 in Rack Mount #4U-440L (with rack mount ears)
• Power Supply: AC 100~240 VAC 50/60Hz (Power Consumption:10A Maximum)
• Safety Approvals: CE, FCC, REACH
• Product Weight: 4.575 Kgs / 10.45 lb
As product improvements are continuous, specifications are subject to change without notice.
4

FRONT PANEL
FRONT PANEL
1. POWER ON SWITCH
The power switch turns the unit on and off. The LCM will illuminate blue to indicate the switcher is ON and receiving power. The switcher
will remember the last setting during a power cycle. When power is removed and resorted, the last configuration will be evoked.
2. STATUS DISPLAY
Front panel status display shows current matrix routing configuration. This same display also shows particular configuration settings
depending on your current function. In run mode (as shown above), the display shows each Output (destination) Channel shows which
input (source) is assigned.
3. IR SENSOR
The IR sensor receives IR commands from the supplied remote controller or a third party IR emitter.
4. INPUT STATUS DISPLAY
Input source 1 to 16 LED illuminate white to indicate a video source is present on that input.
5. SOURCE SELECT BUTTONS
Input 1 thru 16 buttons are provided for each source selection.
6. EDID MODE SELECT BUTTONS
Use button #1 and #2 to select the desired EDID mode.
7. DESTINATION SELECT BUTTONS
Separate outputs 1 thru 16 select buttons are provided for each destination assignment.
Routing can be Source to Destination or one source to multiple destinations.
Example: Press Destination 1, 8, 12 then press Source 2 will route Input 2 to Output 1, 8, 12 respectfully.
8. 19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount. Bracket (part # 4U-440L) INCLUDED. Image shows rack mount bracket attached.
5

FRONT PANEL
FRONT PANEL
8. FUNCTION KEY - ALL Disables (mute) video on all destinations OR assign the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show ”0” to indicate none of the
destinations are assigned a video source.
Option 2
- Press ALL followed by Source 1 thru 16. The display will show the source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
9. FUNCTION KEY - OFF Disables (mute) video on the selected destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 16 output destination. The display will show “ 0 “ for the selected channel,
indicating no video selected.
10. FUNCTION KEY - RECALL The system can save up to 16 sets of learning routes, which are stored in local memory using
Source buttons 1 thru 16 and Destination buttons 1 thru 16 as the memory preset location.
- Press RECALL button.
- Press 1 thru 16 on either Source or Destination row.
- Press ENTER The pre-set configuration will execute.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
11. FUNCTION KEY - ENTER
Press ENTER to confirm entries.
6

FRONT PANEL
FRONT PANEL
12. FUNCTION KEY - MEMORY The system will show store presets, up to a total of 32. Presets are stored in local memory using
Source keys 1 thru 16 or Destination keys 1 thru 16 as the memory preset location.
- Configure desired matrices .
- Press MEMORY button.
- Press 1 thru 16 on either Source or Destination row.
- Press ENTER to ready memory location.
- Or press MEMORY again to cancel operation.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
13. FUNCTION KEY - LOCK - Press and hold LOCK button for two seconds lock out the front panel (as shown on the left).
- Press and hold LOCK button for two seconds to enable the front panel (as shown on the right).
14. FUNCTION KEY - EDID - Press EDID to begin setting up your EDID mode. Use source row buttons #1 and #2 to cycle
thru the options. (Go to page 7 ~ 13 for EDID setup instruction.)
7

FRONT PANEL
FRONT PANEL
16. FUNCTION KEY - EDID (1) Used to display change current EDID mode.
- Press EDID to select new EDID mode or select
- Press SOURCE row #1 or #2 Select EDID modes.
- Press ENTER to ready memory location.
- Or press EDID again to cancel operation.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
FUNCTION KEY - EDID (2) Select external LEARNING mode
- Press EDID to select new EDID mode or select
- Press Destination again, press the same Destination #1 thru #16 to learn HDBaseT out
port EDID, The EDID for HDBaseT (CATx) has been learned.
- Press ENTER to ready memory location.
- Or press EDID again to cancel operation.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
8
Select & change current EDID mode
Select & change current EDID mode