Shinybow USA SB-5684LCM User manual

SB-5684LCM
8x4 +1 Preview Port HDMI Matrix Routing Switcher
w/ Full EDID Management/Learning
INSTRUCTION MANUAL
IMPORTANT WARRANTY INFORMATION.
If you remove the HDMI screw posts, you must use the provided HDMI Locking
Post replacement screws to keep the internal HDMI jack secure. Removing the
HDMI screws without installing the HDMI Locking Post replacement screws will
void your warranty.

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

CONTENTS
INTRODUCTION & CONTENTS ..................................... 1
FEATURES & SPECIFICATIONS .................................. 2
FRONT PANEL ................................................................3
BACK PANEL ..................................................................6
REMOTE CONTROL .......................................................7
RS-232 SERIAL INTERFACE ..........................................9
EDIDFUNCTIONS..........................................................10
IR EXTENDER ...............................................................14
TYPICAL APPLICATION ...............................................15
INTRODUCTION
The SB-5684LCM is high-performance 8x4 matrix routing
switcher for HDMI signals. Supporting (8) HDMI Inputs and (4)
HDMI Outputs and (1) Preview Output (same as Output-01).
The SB-5684LCM is based on the HDMI standards and supports
full resolution HDMI video with embedded EDID. With a signal
bandwidth of 340Mhz, there is no signal degradation. High
denition digital signals can be selected and distributed to any
of the (8) Inputs to the (4) outputs simultaneously. The switcher
is certied as being fully CEC and HDCP 1.3 compliant, with
RoHS, CE, FCC certications and supports full HD HDMI V1.4a
3D formats and data rates up to 6.75Gbps, enabling 1080p HDMI
formats and UXGA/WUXGA/DVI 1920x1200 resolutions to any
HD display. Supporting high resolution HDMI sources routed to
HDMI displays, monitors, projector or audio receivers. The EDID
management can be selected between (7) different modes.
Control is provided via front panel push buttons, IR remote, RS-
232 or TCP/IP (not a web-browser). A RS-232 / TCP-IP Windows
GUI interface is provided for matrix routing. 3 Year Warranty.
PACKAGE CONTENTS
Check that you have the following components:
• SB-5684LCM Matrix Routing Switcher
• RS-232 V2.0 / Ethernet V2.0 Protocol Instructions
• IR Remote Control (SW-5684)
• 19 inch Ear mount bracket (Part# 1U-440L)
• SB-100 IR Extender Receiver Set
• CD Contents: Manual, Windows GUI, ISP V1.0 Windows driver
• RS-232 Cable 6.5 feet (2M)
• HDMI Locking Post Replacement Screws
• Users Guide
• Power Supply: 12VDC, 5A Universal Type 50/60Hz, 100~240VAC
• Optional:SB-100CIRExtenderReceiverCable(6.5ft(2M))
1
HDMI Matrix Switcher Series
ThankyouforpurchasingtheSB-5684LCMHDMIMatrixSwitcher.Youwillndthisuniteasytoinstallandhighlyreliable
butitisessentialthatyoureadthismanualthoroughlybeforeattemptingtousethe8x4HDMImatrixswitcher.
TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise — without express written permission and consent.
© Copyright 2017. All Rights Reserved.
Version 2.4 SEPT 2017
5684-20141126-004
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.

FEATURES
• (8) HDMI digital source devices matrix switched to (4) HDMI devices
• HDMI digital video w/ embedded audio, DVI format and CEC/HDCP 1.3 compliant
• (7) function key control and (7) worldwide EDID modes for HDTV resolutions
• Link speeds of up to 6.75Gbps (link clock rate of 340MHz), Supports HDMI 1.4a 3D formats
• Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV resolutions 480i/480p, 576i/576p, 720p, 1080i & 1080p
• Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV and audio receivers/ampliers
• Digital Video TMDS formats with resolutions up to 1080p-60 with Deep color 36-bit
• Digital Audio Support: Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex, DTS, DTS-HD, DTS-HD Master, DTS-EX, PCM, PCM2, LPCM2
• Various User Interface Control:
• Windows based GUI control via RS-232 port
• Windows based GUI control via TCP/IP port (not a web-browser)
• Front panel push buttons
• IR wireless remote control
• Third party RS-232 control (via simple ASCII)
• Ethernet TCP/IP series interface (switch control)
• Supports world wide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK
• Supports EDID Modes:
• Embedded EDID Modes: FSS / H24-3D / H24-3D-M / H36-3D / H36-3D-M / DVI-D 1280x1024-60Hz / DVI-D 1920x1200-60Hz
• External Modes: Learning mode
• Automatic scanning of input & output status via LED show on front panel
• Supports preview output port simultaneously with Output #1
• Supports the IR remote and an IR extenders for distances up to ~984 ft (300M) Max
• EDID conguration via internal modes
• Consumer Electronic Control (CEC) switch all open or OFF
The switcher will remember that last state during a power cycle. When power is removed and resorted, the last conguration will be invoked.
2
FEATURES

SPECIFICATIONS
• Type of Switcher: (8) HDMI Inputs to (4) HDMI Outputs Matrix Switcher
• HDMI Support: HD 1080p@60Hz, H36-bit Deep color, 3D (1.4a) formats
• HDCP / CEC Support: HDCP 1.3 Compliant, CEC Compliant
• Video Bandwidth: Double Data Rates: 340MHz, Total 6.75Gbps bandwidth
• Digital Video Support: Full HD resolution: 480i / 480p / 720p / 1080i / 1080p
• Digital Audio Support: Multi Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES
6.1, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• Controls:
• IR Remote Control (remote switcher)
• IR External port (switch control)
• Select & Function buttons on front panel
• RS-232 series interface (switch control)
• Ethernet TCP/IP series interface (switch control)
• Preview output: Supports (1) preview output port simultaneously via Output-#1
• Source Status: Automatically scans source Inputs via LED
• Function Control Key: ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID
• Infrared Frequency: 38KHz
• IR External Distance: ~1000 feet / 300M maximum
• HDMI I/O Connector: HDMI Type A - SMD 19pin female type
• Temperature: 32°F - 100°F Operation (0°C - 38°C)
• Dimensions (LxWxH): 17.5 x 10 x 1.75 in
• Rack Mount: 1RU High 19 in Rack Mount (with rack mount)
• Power Supply: DC12V / 5A, Universal world wide type 50/60Hz, 100~230VAC
• Power Consumption: 3550mA Maximum
• Safety Approvals: CE, FCC, RoHS (2002/95/EC)
• Weight: 6.6 lb (Unit only) / 9.0 lb (Net)
As product improvements are continuous, specications are subject to change without notice.
Because of limitations on source and display devices, not all EDID data is compatible and subsequently not all equipment will function
correctly with this switcher.
3
SPECIFICATIONS

4
FRONT PANEL
FRONT PANEL
1. POWER SWITCH: The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and is receiving
power. The switcher will remember the last state during a power cycle. When power is removed and resorted, the last conguration will be
evoked.
2. INPUT STATUS DISPLAY: Input sources 1 to 4 LCM illuminates blue to indicate that a video source is present on that input.
3. OUTPUT STATUS DISPLAY: Each Output (destination) channel shows which input (source) it is assigned.
4. DESTINATION SELECT BUTTONS: Separate outputs 1 thru 4 select buttons are provided for each destination assignment. Routing can be
source to destination or one source to multiple destinations.
Example: Press Destination 1, 3, 4, then press Source 2. It will route Input 2 to Output 1, 3, 4 respectfully.
5. EDID MODE SELECT BUTTONS: Used to select EDID mode using Input buttons #1 and #2.
6. IR SENSOR: The IR sensor receives IR commands from the supplied remote control or third party IR emitter.
7. SOURCE SELECT BUTTONS: Separate inputs 1 thru 8 select buttons are provided each source selection.

5
FRONT PANEL
FRONT PANEL
8. FUNCTION KEY - ALL:
Disables (mutes) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show “0“ indicating all destinations
have no video selected.
Option 2
- Press ALL followed by Source 1 THRU 8. The display will show the Source selected.
- Press ENTER. The pre-set source selection will be assigned all destinations.
9. FUNCTION KEY - OFF:
Disables (mutes) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press 1 THRU 4 output destination. The display will show “0“ for the selected channel
indicating no video selected.
10. FUNCTION KEY - RECALL:
The system will show previously stored presets, up to a total of (12).
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 4 as
the memory preset location.
- Press RECALL button.
- Press 1 THRU 8 on either Source or 1 THRU 4 Destination row.
- Press ENTER. The pre-set conguration will execute.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.
11. FUNCTION KEY - ENTER: Press ENTER to conrm entries.

6
FRONT PANEL
FRONT PANEL
12. FUNCTION KEY - MEMORY:
The system will show stored presets, up to a total of (12). Presets are stored in local memory
using Source keys 1 thru 8 or Destination keys 1 thru 4 as the memory preset location.
- Congure desired matrices.
- Press MEMORY button.
- Press 1 THRU 8 on either Source or 1 THRU 4 Destination row.
- Press ENTER to ready memory location.
- Or press MEMORY again to cancel the operation.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.
13. FUNCTION KEY - LOCK:
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
14. FUNCTION KEY - EDID:
- Press EDID to select new EDID mode or select source row #1 or #2 for LINK source
EDID again.
- Press the DESTINATION # to learn EDID the Destination EDID has been learned.
15. 19 INCH EAR MOUNT PAIR: Converts desktop to 19 inch rack mount. Bracket (part # 1U-440L) INCLUDED. Image shows rack mount
bracket attached.

7
BACK PANEL
BACK PANEL
1. DC POWER INLET: The switcher is tted with a DC power plug input
connector. Ensure that the outlet is of an approved type and is of sufcient
current carrying connector capacity with the correct voltage and connector
polarity. 12Volt DC power supply 5A Max (Center pin positive).
2. IR EXTENDER CONTROL: Supports one IR Extender (IR input) for a
maximum extended distance of up to ~984 feet/300M.
NOTE: DO NOT install or remote this connection with the power ON.
3. RS-232 CONNECTION: RS-232 control port allows for interfacing to a PC,
such as a computer or touch panel control, to the switcher via the DB-9pin
female connector for serial RS-232 control.
4. ETHERNET CONNECTION: ETHERNET control port allows for TCP/IP
interfacing to a PC, such as a computer or touch panel control (not a web-
browser), to the switcher via a RJ-45 female connector to control the switcher.
5. PREVIEW OUTPUT-01 HDMI: Connects a HDMI digital video/audio signal
direct to the female HDMI connector. This connector supports HDMI digital
video/audio and DVI digital video sources. HDMI signal is the same as
Output #1. If you remove the HDMI screw posts, you must use the provided
HDMI Locking Post replacement screws to keep the internal HDMI jack
secure. Removing the HDMI screws without installing the HDMI Locking
Post replacement screws will void your warranty.
6. INPUTS- 1,2,3,4,5,6,7, & 8 HDMI: Connects a HDMI digital video/audio
signal direct to the female HDMI connector. This connector supports HDMI
digital video/audio and DVI digital video sources. If you remove the HDMI
screw posts, you must use the provided HDMI Locking Post replacement
screws to keep the internal HDMI jack secure. Removing the HDMI screws
without installing the HDMI Locking Post replacement screws will void your
warranty.
HDMI Digital Video/Audio. Connector with x screws for Inputs 1~8
7. OUTPUTS- 1,2,3 & 4 HDMI: Connects a HDMI digital video/audio signal
direct to the female HDMI connector. This connector supports HDMI
digital video/audio and DVI digital video sources. If you remove the HDMI
screw posts, you must use the provided HDMI Locking Post replacement
screws to keep the internal HDMI jack secure. Removing the HDMI screws
without installing the HDMI Locking Post replacement screws will void your
warranty.
HDMI Digital Video/Audio. Connector with x screws for Outputs 1~4
POWER JACK:
DC Jack - Inner OD Ø 2.1mm (+)
Outside OD Ø 5.5mm (GND)
Power input - 12VDC, 5A
IR EXTENDER JACK: Female jack - inner OD Ø 3.5mm
REMOTE PORT: DB-9pin female connector
REMOTE PORT: Control the switcher RJ-45 female
connector.
ETHERNET PORT: NOTE: The Ethernet port and
RS-232 port cannot be used simultaneously. Any
connection to the Ethernet port will disable serial
commands send to the RS-232 port.
HDMI DIGITAL VIDEO/AUDIO CONNECTOR: HDMI
female connector
NOTE: With the proper adapters, the switcher can
be used with DVI digital video signals, as it is HDCP
compliant. DVI does not support audio.
HDMI DIGITAL VIDEO/AUDIO CONNECTOR: HDMI
female connector
Note: With the proper adapters, the switcher can
be used with DVI digital video signals, as it is HDCP
compliant.
HDMI DIGITAL VIDEO/AUDIO CONNECTOR: HDMI
female connector
NOTE: With the proper adapters, the switcher can
be used with DVI digital video signals, as it is HDCP
compliant.

8
REMOTE CONTROL
Before making any connections observe the following:
• Ensure the main voltage supply matches the label on the supplied plug-pack (+/-10%).
• Ensure that the power switch is OFF.
• Ensure that all system grounds (earth) are connected to a common point.
• Avoid powering equipment within a system from multiple power sources that may be separated by large distances.
• Connect all audio video sources and destination equipment.
• Power up all source and destination audio-visual sources.
• For each destination output select the appropriate input source by using the front panel input select buttons. The supplied IR remote
control. Or through the RS-232 serial communications port.
• Upon powering up the switcher, it will return to its last used setting before being powered down.
REMOTE CONTROL
1. & 2. SWITCH POWER ON or OFF:
Power ON and OFF
3. DESTINATION: 1 THRU 4 OUTPUT SELECTION:
Destination buttons to select the output display channel
4. SOURCE: 1 THRU 8 INPUT SOURCE SELECTION:
Input 1~8 source selection buttons
5. FUNCTION KEY: Function selection buttons
ALL OFF EDID RECALL
MEMORY ENTER LOCK

9
REMOTE PROTOCOL COMMANDS
IR REMOTE CUSTOM AND DATA CODES (NEC Standard)
HOW TO SETUP IR CODES : CUSTOM CODE : 1FE0
DATA CODE :
POWER ON: 1FE0 A15E ALL: 1FE0 B04F RECALL: 1FE0 B24D
POWER OFF: 1FE0 A25D OFF: 1FE0 B14E MEMORY: 1FE0 B44B
EDID: 1FE0 B748 LOCK: 1FE0 B54A ENTER: 1FE0 B34C
PRESS TV DESTINATION - # then PRESS AV SOURCE - #
DESTINATION #1 : 1FE0 10EF
DESTINATION #2 : 1FE0 20DF
DESTINATION #3 : 1FE0 30EF
DESTINATION #4 : 1FE0 40BF
SOURCE #1 : 1FE0 01FE
SOURCE #2 : 1FE0 02FD
SOURCE #3 : 1FE0 03FC
SOURCE #4 : 1FE0 04FB
SOURCE #5 : 1FE0 05FA
SOURCE #6 : 1FE0 06F9
SOURCE #7 : 1FE0 07F8
SOURCE #8 : 1FE0 08F7
For Example:
Select Destination # 1 to show Source #1~8
The IR Data Code list:
Destination # 1, Source #1 1FE0 10EF 1FE0 01FE
Destination # 1, Source #2 1FE0 10EF 1FE0 02FD
Destination # 1, Source #3 1FE0 10EF 1FE0 03FC
Destination # 1, Source #4 1FE0 10EF 1FE0 04FB
Destination # 1, Source #5 1FE0 10EF 1FE0 05FA
Destination # 1, Source #6 1FE0 10EF 1FE0 06F9
Destination # 1, Source #7 1FE0 10EF 1FE0 07F8
Destination # 1, Source #8 1FE0 10EF 1FE0 08F7

10
ETHERNET SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM VERSION COMPATIBLE V2.0
For a complete list of commands, please reference external document extended Ethernet Protocol Instruction Manual.
ETHERNET SERIAL INTERFACE
PIN ETHERNET REFERENCE
1 TXOP TX +
2 TXON TX -
3 RXIP RX +
4 NC
5 NC
6 RXIN RX -
7 NC
8 GND
RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0
For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual.
RS-232 CONFIGURATION
RS-232 cable is a straight thru cable and not null-modem
Denition Pin Pin Denition
1 1 DCD
TX 2 2 RX
RX 3 3 TX
4 4 DTR
GND 5 5 GND
6 6 DSR
7 7 RTS
8 8 CTS
9 9 RI
RS-232
RS-232 SERIAL INTERFACE PROTOCOL COMMANDS ( ETHERNET / RS-232 CONTROL DRIVER V2.0 )
The Shinybow switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control
system.
The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1.
When the unit recognizes a complete command it will perform the requested action - there is no delimiter character required.
ETHERNET & RS-232 SERIAL INTERFACE
PC
Shinybow
Device
ETHERNET TCP/IP PROTOCOL COMMANDS
( ETHERNET / RS-232 CONTROL DRIVER V2.0 )
**TheEthernetportandRS-232portCANNOTbeused
simultaneously.AnyconnectiontotheEthernetControlport
willDISABLEserialcommandssenttotheRS-232port.**
Note :
Control the switcher
SPD : Speed
LINK : Ethernet link
RJ-45 Female 8P-8 Connector
RS-232 PIN DIAGRAM

11
SYSTEM RESET
SYSTEM RESET RETURN SWITCH TO FACTORY DEFAULTS
Press RECALL > OFF > ENTER RESET to Factory Default
1. Press RECALL button: The LCM will show the current stored presets status.
2. Press OFF button: The LCM will show “SYSTEM RESET”
3. Press ENTER button: To conrm entries.
The switch will reset all customizable values back to factory defaults.
You must POWER CYCLE the switch for the new values to take effect.
NOTE: Factory Reset Defaults to:
1. Source Destination will be set to 1-1, 2-2, 3-3, etc.
2. Switch matrices stored in memory will be cleared.
3. Lock function will return to Un-Locked.
4. AUX function will disable and return to UN-AUX (On Select Models).
5. ARC function will disable and return to SPDIF as the Output (On Select Models).
6. EDID will return to FSS®(1080p-2ch Mode).
7. Ethernet port will return to DHCP=ENABLED.
RESET EDID
EDID RESET PROCEDURE
From the Front Panel:
Press EDID > RECALL > OFF > ENTER
RESET EDID
Press EDID.
Press RECALL.
Press OFF. The display should show Reset EDID.
Press ENTER.
LEARNING MODE 2 SETTING EDID TO LEARNING MODE 2
Press EDID > OFF > DESTINATIONS > ENTER
The EDID for HDMI has been passed from the
Destination port to the Source port.
1. Press EDID button: The LCM will show the current EDID status.
2. Press OFF button: Does the OFF button stay illuminated?*
*If Yes: Press ALL the Destination buttons individually so they illuminate blue.
The switcher will LEARN the destination HDMI EDID and pass to the selected
source. The switcher will Enable or Disable HDMI EDID for the selected source.
3. Press ENTER to conrm changes. The LCM will return to the default screen
showing selected matrix routing status. This puts you in Learning Mode 2.
*If No: You might need a f/w update.
EDID FUNCTION - SYSTEM RESET/FACTORY RESET

12
EDID FUNCTION
EDID FUNCTION SETUP
EDID SETUP To Change The EDID Setup
Step 1. Press the EDID button The display will show the currently selected EDID mode.
Step 2. Press SOURCE #1 OR #2 button row The button will ash blue and the display will show the current Embedded EDID Status.
Step 3. Press the ENTER button To set EDID mode. The switcher will return to operation mode.
Operation will abort if no keys are pressed within 5 seconds.
EMBEDDED EDID MODES Total 7 EDID Modes
Embedded EDID Setup
Press EDID > SOURCE > ENTER
SOURCE #1 or SOURCE #2
To select Embedded EDID mode or LEARNING mode.
Press EDID button: The LCM will show the current EDID status.
Repeatedly pressing the SOURCE 1 button will cycle up thru the options.
Repeatedly pressing the SOURCE 2 button will cycle down thru the options.
Embedded EDID:
Mode 1 : FSS®
Mode 2 : H24-3D
Mode 3 : H24M-3D
Mode 4 : H36-3D
EDID FUNCTION FOR HDMI MATRIX SWITCHER
RESET EDID Return To Factory Default
How to RESET EDID mode
Press EDID > RECALL > ENTER
To RESET to FACTORY DEFAULT (1080p-2CH).
Press EDID button: The LCM will show the current EDID status.
Press RECALL button: The LCM will show the RESET EDID.
Press ENTER to conrm entries.
The EDID will return to FSS®mode and resolution 1080p-2CH.
EDID STATUS To View The Current EDID Status
Step 1. Press EDID button The button will ash blue and the display will show the current Embedded EDID Status.
Step 2. Press EDID button To exit.
HOW TO SETUP FSS®FUNCTION Fast Speed Start®
Step 1. Press the DESTINATION #1~4 button row
Then Press the SOURCE #1~8 button row
To setup and Install all devices.
Step 2. Press EDID button Select a optimum status of Embedded EDID mode.
Step 3. Press ENTER button To conrm entries.
Step 4. Press EDID button To select the EDID FSS®mode.
Step 5. Press ENTER button To conrm entries.
Mode 5 : H36-3D-M
Mode 6 : DVI 1280x1024-60Hz
Mode 7 : DVI-D 1920x1200-60Hz

13
EDID FUNCTION
EDID FUNCTION: (8) EMBEDDED EDID MODES
EDID FUNCTION: (8) EMBEDDED EDID MODES
Mode 1. FSS®(Fast Speed Start®)Video Support: All resolutions up to and including 1080p.
Automatic capture of the most suitable EDID from Destination to Source.
Mode 2. H24-3D (1080p-24bits) Video Support: All resolutions up to and including 1080p.
Audio Support: PCM 2CH
Mode 3. H24-3D-M (1080p-24bits) Video Support: All resolutions up to and including 1080p.
Audio Support: MAT (MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3
5.1CH, DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
Mode 4. H36 (1080p-36bits) Video Support: All resolutions up to and including 1080p.
Audio Support: PCM 2CH
Mode 5. H36-M (1080p-36bits) Audio Support: MA(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3
5.1CH, DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
Mode 6. 1280x1024-60Hz (DVI-D) DVI Support: DVI-D 1280x1024 60Hz
Mode 7. 1920x1200-60Hz (DVI-D) DVI Support: DVI-D 1920x1200 60Hz

14
EDID FUNCTION
EDID FUNCTION FOR HDMI MATRIX SWITCHER
LEARNING EDID Learning EDID from Destination to Source
Learning EDID setup
Press EDID > DESTINATION > SOURCE > ENTER
Press: EDID > DESTINATION #1 >
The switcher will LEARN destination #1 EDID and pass the selected source.
NOTE: The already learned EDID cannot be modied. You can only rebuild a new Learning EDID.
For Example; When the Source has “Learned” the EDID data from a destination, it will save that EDID information into EPROM and
the EDID data cannot change. Please select new learning destination to sources or change to one of the embedded EDID modes when
you want to remove the learning EDID memory from EPRPM.
LEARNING EDID SINGLE TO SINGLE Learning Destination #2 EDID To Source #3
Step 1. Press EDID button The button will ash blue and the display will show the current Embedded EDID Status.
Step 2. Press the DESTINATION #2 button row Copy the Destination #2 Display EDID.
Step 3. Press the SOURCE #3 button row Learning the Destination #2 EDID To Source # 3.
Step 4. Press ENTER button To conrm entries.
LEARNING EDID SINGLE TO MULTIPLE Learning Destination EDID Link To The Majority Sources
Step 1. Press EDID button The button will ash blue and the display will show the current Embedded EDID Status.
Step 2. Press the DESTINATION #1~4 button row Copy any #1~4 Destinations EDID.
Step 3. Press the SOURCE #1~8 button row Learning the Destination EDID link to source #1~8.
Step 4. Press ENTER button To conrm entries.
LEARNING EDID SINGLE TO ALL Learning Destination EDID Link To All Sources
Step 1. Press EDID button The button will ash blue and the display will show the current Embedded EDID Status.
Step 2. Press destination button 1 THRU 4 Learning anyone 1~4 Destination EDID to all sources.
Step 3. Press ALL button Learning selected destination EDID to all sources.
Step 4. Press ENTER button To conrm entries.
LEARNING EDID DEFINITION Learning EDID From Destination To Source
1. Switcher will LEARN destination EDID and pass the selected source.
2. To set up learning between a single destination and single source: Press EDID button > Press DESTINATION 1 THRU 4 > Press SOURCE 1
THRU 8 > Press ENTER to conrm. Switcher will learn destination EDID to source device.
3. To set up learning between a single destination and Multiple sources: Press EDID button > Press DESTINATION 1 THRU 4 > Press the
majority SOURCES 1 THRU 8 > Press ENTER. Switcher will learn single destination EDID to many source devices.
4. How to Learning single destinations with all sources. Press EDID button > Press ALL button > Press ENTER to conrm.
AUTO MODE DEFINITION Common Resolution And Audio
Switcher will nd highest common Resolution and Audio from all destination EDID to link Source.
Example for single source: Destination > Press #1 and then Source > Press #1 Destination device #1 will set to the highest common
resolution and Audio of source #1
Example for multiple sources: Destination device #1, #2, #3 will be set to the highest common resolution and Audio available and source
device #1 will output this same resolution.

Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).
Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
SB-100 IR Receiver Set
IR Receiver cable 6ft (2M)
SB-100C IR Receiver Cable
1. SB-100 IR 300M Receiver
Switcher IR EXT. In Cable (3C) IR Receiver (SB-100)
2. SB-100C IR 2M Receiver Switcher IR EXT. In Cable (2C) IR Receiver (SB-100C)
Pin configuration for IR 984 feet (300M) Extender Receiver such as SB-100 compatible
VCC (Ring)
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring :VCC
Sleeve: GND
Ring
Tip (center)
Sleeve
SB-100 IR Receiver Set
Pin configuration for IR Receiver 6 feet (2M) cable such as SB-100C compatible
IR Receiver cable 6ft (2M)
SB-100C IR Receiver Cable
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring: NC
Sleeve: GND
Ring
Tip (center)
Sleeve
The SB-100 IR Receiver is required when using the port “ALL in” Jack.
The SB-100C IR Receiver will not function on the port “ALL in” Jack.
SB-100C Maximum Distance ~ 6 feet (2M)
IN P UT
DC 1 2V
R o H S /95/E C
IR EXT .
RS -232
RS-232 IR E X T. in
ANI-100
IR Rx
POWER
INPUT-1
1234
1 2 34
1234
1 2 3 4
HDMI MAT RIX S W IT CHER
ONOFF
INP UT- 2
INP UT-3
INP UT-4
SWIR
Distance: Max.(2M)
IR PN#: SB-XXXX
Control Switch SB-XXXX
IN P UT
DC 1 2V
R o H S /9 5 /E C
IR EXT .
RS -232
RS-232 IR E X T. in
ANI-100
IR Rx
POWER
INPU T - 1
1 2 3 4
1234
1 2 3 4
1234
HDMI MATRIX SW IT CH E R
ON OFF
INPUT- 2
INPUT -3
INPUT-4
SW IR
Distance: Max.300M
IR PN#: SB-XXXX
Control Switch SB-XXXX
SB-100 Maximum Distance ~ 984 feet (300M)
SB-100 Receiver and SB-101 Transmitter The DISTANCE maximum ~ 984 feet (300M)
SB-100 Receiver and SB-101C Transmitter The DISTANCE maximum ~ 984 feet (300M)
IR EXTENDER
The frequency range of the IR emitter and receivers is 38khz.
15
IR EXTENDER

INSTALLING DIAGRAM
Sample Connection:
Using RS-232 serial interface or Ethernet TCP/IP to control switch (SB-5684LCM) and preview output port simultaneously via Output-#1
to an extra HDMI HDTV, Display or Monitor.
Supports a HDBaseT™Extender via the SB-6335T Transmitter and SB-6335R Receiver with a CAT6/6a/7 cable.
16
TYPICAL APPLICATION
NOTE:
1. IR Control Projector Over HDBaseT™ Extender:
SB-6335T HDBaseT™Transmitter
SB-6335R HDBaseT™Receiver
2. RS-232 Control
3. External IR Remote
4. IR Extender Transmitter: SB-101 IR Transmitter
5. IR Extender Receiver: SB-100 IR Receiver

INSTALLING DIAGRAM
Sample Connection:
Using an Audio Extractor (SB-5609) to an Audio Amplier and ARC Control Box (SB-5610) to link the TV return audio to an audio device. Control
a Satellite Receiver source via a HDBaseT™Transmitter (SB-6335T) and Receiver (SB-6335R).
NOTE:
1. IR Control Satellite Receiver Over HDBaseT™CAT6/6a/7
Extender from a room:
SB-6335T HDBaseT™CAT6/6a/7 Transmitter
SB-6335R HDBaseT™CAT6/6a/7 Receiver
2. Audio Extractor To Recode Audio:
SB-5609 HDMI Audio Extractor
3. Control HDMI ARC: SB-5610 ARC Control Box
4. IR Extender Transmitter: SB-101 IR Extender Transmitter
5. IR Extender Receiver: SB-100 IR Extender Receiver
Supports a HDBaseT™Extender via the SB-6335T Transmitter and SB-6335R Receiver with a CAT6/6a/7 cable.
17
TYPICAL APPLICATION

THIS PAGE IS INTENTIONALLY LEFT BLANK.