Show Tec 50348 User manual

Multi Exchanger V2
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 50348
MANUAL
ENGLISH

1
Ordercode: 50348
Multi Exchanger
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Connection with the mains.........................................................................................................................................4
Return Procedure..........................................................................................................................................................5
Claims..............................................................................................................................................................................5
Description of the device.................................................................................................................................................6
Features ..........................................................................................................................................................................6
Frontside..........................................................................................................................................................................6
Backside .........................................................................................................................................................................7
Installation...........................................................................................................................................................................7
Set Up and Operation .......................................................................................................................................................8
Maintenance......................................................................................................................................................................9
Replacing the Fuse.......................................................................................................................................................9
Troubleshooting .................................................................................................................................................................9
Product Specification .....................................................................................................................................................10

2
Ordercode: 50348
Multi Exchanger
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
Showtec Multi Exchanger with a Schuko power cable (1,2 m)
User manual
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.

3
Ordercode: 50348
Multi Exchanger
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Do not open the device and do not modify the device.
Never leave any cables lying around.
Do not connect this device to a dimmer pack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoors, avoid contact with water or other liquids.
Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of the reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the Multi Exchanger. The
manufacturer will not accept liability for damages caused by the misuse or incorrect installation of
this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
Repairs, servicing and electric connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.

4
Ordercode: 50348
Multi Exchanger
Operating Determinations
This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
The maximum ambient temperature ta = 35°C must never be exceeded.
The relative humidity must not exceed 50 % with an ambient temperature of 35°C.
If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!

5
Ordercode: 50348
Multi Exchanger
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

6
Ordercode: 50348
Multi Exchanger
Description of the device
Features
The Showtec Multi Exchanger converts a DMX-512 signal to a 72-channel analog output.
Input voltage: 230V AC, 50Hz
Analog output: +(-)10V, +(-)12V and +(-)15V
Control: DMX mode, MIDI mode, HOLD mode
Connections: 3 x 25-pin D OUT, 3-pin/5-pin DMX IN/OUT & MIDI IN/THRU
Possibility to pre-store an emergency scene
Memory backup with EEPROM
CHASE function for channels 1-72 & speed control
NOTE ON / OFF signal for MIDI
Housing: Die-cast aluminum
Fuse: F1L/250V
Dimensions:
483 x 126 x 44 mm (LxWxH)
19 inch x 1HE
Weight: 2,6 kg
Frontside
Fig. 01
01) Power switch ON/OFF
02) Fuse F1L/250V
03) LED display
04) UP button
Press the button to increase the DMX address/adjust options.
05) MENU button
Press the button to enter the DMX or MIDI mode and to confirm the settings.
06) DOWN button
Press the button to decrease the DMX address/adjust options.
07) CHASE button
Press to enter the CHASE mode. Then it is possible to set the chase speed between 01-99 and select
the desired channel between 01-72.
08) STORE button
Press the button to store a scene or to run a pre-stored scene.
09) MIDI IN connector
Use this connector to receive MIDI data.
10) MIDI THRU connector
Use this connector to repeat or send MIDI input.
11) 3-pin DMX signal connector IN
Use this connector to receive DMX signals.
12) 3-pin DMX OUT connector OUT
Use this connector to send DMX signals.
13) 5-pin DMX signal connector IN
Use this connector to receive DMX signals.
14) 5-pin DMX OUT connector OUT
Use this connector to send DMX signals.

7
Ordercode: 50348
Multi Exchanger
Backside
Fig. 02
15) 1-24 channel 25-pin 'D' connector OUT
16) 25-48 channel 25-pin 'D' connector OUT
17) 49-72 channel 25-pin 'D' connector OUT
18) Output level DIP switches
Flip the DIP switches to set the desired output level: 10V, 12V or 15V. See fig. 03 for more information.
19) Analog output polarity
Move the switch to the left for "+" output, or to the right for "-" output. See fig. 03 for more information.
20) Schuko power cable (1,2 m)
Fig. 03
Installation
Remove all packing materials from the Multi Exchanger. Check if all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.

8
Ordercode: 50348
Multi Exchanger
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 110V specification product on 230V power, or vice versa.
01) Flip the power switch (01) to ON position.
02) Press and hold down the MENU button (05) for 5 seconds to enter the mode settings.
03) Repeatedly press the MENU button (05) to toggle between the following operation modes:
Mode selection
Press the UP/DOWN buttons (04/06) to select DMX or MIDI. The corresponding
LED will blink.
Press the MENU button (05) to confirm.
DMX mode
When the DMX LED blinks, the display will show the blinking DMX starting
address (A001–A512).
Press the UP/DOWN buttons (04/06) to select the desired address.
Press the MENU button (05) to confirm.
MIDI mode
When the MIDI LED blinks, the display will show the blinking channel number
(CH01–CH16).
Press the UP/DOWN buttons (04/06) to select the desired channel.
Press the MENU button (05) to confirm.
HOLD mode
When the display shows ON or OFF, the HOLD LED will be on.
Press the UP/DOWN buttons (04/06) to select ON/OFF.
If set to ON, the device will use the last active scene, in case of a DMX failure.
If set to OFF, the last active scene will not be used.
Speed settings
When the display shows SP01-SP99, press the UP/DOWN buttons (04/06) to
select the desired chase speed.
The adjustment range is between 01-99, from slow to fast.
Channel settings
When the display shows C-01–C-72, press the UP/DOWN buttons (04/06) to
select the desired channel.
Press the MENU button (05) to confirm and leave the mode settings.
If you select C-48, the channels 1-48 will be executed in a sequence.
04) When the DMX LED is lit, the display shows the DMX starting address AXXX and the 72 channel DMX
signals, beginning from the AXXX, will be converted to 72 channel analog outputs. If a DMX signal is
present, the DMX LED will blink.
05) When the MIDI LED is lit, the display shows the MIDI channel number (CH01–CH16). The MIDI signals
from NOTE NO. 22-93 are converted to 72 channel analog outputs. When a MIDI signal is present, the
MIDI LED will blink.
06) When the device receives a DMX signal, after the setting of scenes has been finished, press and hold
down the STORE button (08) for 5 seconds until the display shows GOOD. The scene will have been
saved. Release the STORE button (08) to return to DMX input.
07) Press the STORE button (08) to run a pre-stored scene. The display will shows STOR. In the mode
settings, this function is not available.
08) Press the CHASE button (07) to enter the CHASE mode. The display will show CHAS.
09) Choose one of the 3 analog output options: +(-) 10V, +(-) 12V or +(-) 15V.
Make sure that the DIP switch # 1 is always set to ON.
Set the DIP switch #2 to ON for 15V, DIP switch #3 for 12V or DIP switch #4 for 10V.
Remember that any two of the DIP switches #2, 3 and 4 may not be set to ON at the same time.

9
Ordercode: 50348
Multi Exchanger
Maintenance
The Showtec Multi Exchanger requires almost no maintenance. However, you should keep the unit clean.
Disconnect the mains power supply and then wipe the cover with a damp cloth. Do not use alcohol or
solvents. Do not immerse in liquid.
Keep connections clean. Disconnect electric power, and then wipe the connections with a damp cloth.
Make sure connections are thoroughly dry before linking equipment or supplying electric power.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and must
not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out. If the
fuse burns out, the product will not function whatsoever. If this happens, follow the directions below.
01) Unplug the unit from electric power source.
02) Insert a screwdriver into the fuse holder. Turn the fuse holder counterclockwise. The fuse holder will
come out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse holder. Be sure
to use a fuse of the same type and specification. See the product specification label for details.
Troubleshooting
This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps
below in sequence until a solution is found. Once the unit operates properly, do not carry out following
steps.
01) If the device does not operate properly, unplug the device.
02) Check power from the wall, all cables, the DIP switch settings (return to default), etc.
03) If all of the above appears to be O.K., plug the unit in again.
04) If nothing happens after 30 seconds, unplug the device.
05) Return the device to your Showtec dealer.

10
Ordercode: 50348
Multi Exchanger
Product Specification
Model:
Showtec Multi Exchanger
Input voltage:
230V AC, 50Hz
Fuse:
F1L/250V
Dimensions:
483 x 126 x 44 mm (LxWxH)
19 inch x 1HE
Weight:
2,6 kg
Operating and Programming:
Signal pin OUT:
Pin 1 (earth), pin 2 (-), pin 3 (+)
Signal input:
3-pin/5-pin XLR IN, MIDI IN
Signal output:
3-pin/5-pin XLR OUT, MIDI THRU
Electro-mechanical effects:
Analog output:
+(-)10V, +(-)12V and +(-)15V
Onboard:
LED display for easy setup
Control:
DMX mode, MIDI mode, HOLD mode
Housing:
Die-cast aluminum
Connections:
3 x 25-pin D OUT, 3-pin/5-pin DMX IN/OUT & MIDI IN/THRU
Max. ambient temperature ta:
35°C
Max. housing temperature tB:
80°C
Minimum distance:
Minimum distance from flammable surfaces:
0,5 m
Design and product specifications are subject to change without prior notice.
Website: www.Showtec.info
Email: [email protected]

©2017 Showtec