Show Tec Pixel User manual

Pixel Controller
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Product code: 44510
USER MANUAL
ENGLISH
V2

1
Pixel Controller
Product code: 44510
Preface
Thank you for purchasing this Showtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.
This user manual contains information concerning:
●Safety instructions
●Intended and non-intended use of the device
●Installation and operation of the device
●Maintenance procedures
●Troubleshooting
●Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of
property.
©2021 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written
consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document or for other language versions, please visit our website
www.highlite.com or contact us at [e-mail].
Highlite International and its authorized service providers are not liable for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or
reliance on the information contained in this document.

2
Pixel Controller
Product code: 44510
Table of contents
1. Introduction..........................................................................................................................................................4
Before Using the Product ..................................................................................................................................4
Intended Use .......................................................................................................................................................4
Product Lifespan.................................................................................................................................................4
Text Conventions ................................................................................................................................................4
Symbols and Signal Words................................................................................................................................5
Symbols on the Information Label ..................................................................................................................5
2. Safety ....................................................................................................................................................................6
Warnings and Safety Instructions ....................................................................................................................6
Requirements for the User.................................................................................................................................8
3. Description of the Device...................................................................................................................................9
Front View ............................................................................................................................................................9
Back View ............................................................................................................................................................9
3.3. Side View ...........................................................................................................................................................10
Product Specifications ....................................................................................................................................10
Compatibility.....................................................................................................................................................11
Recommended Software...............................................................................................................................11
Dimensions.........................................................................................................................................................11
4. Installation ..........................................................................................................................................................12
4.1. Safety Instructions for Installation ..................................................................................................................12
Personal Protective Equipment .....................................................................................................................12
4.3. Installation Site Requirements ........................................................................................................................12
4.4. Rigging ...............................................................................................................................................................12
4.5. Connecting to Power Supply.........................................................................................................................13
4.6. Power Linking of Multiple Devices.................................................................................................................14
5. Setup ...................................................................................................................................................................14
5.1. Warnings and Precautions .............................................................................................................................14
5.2. DMX Connection..............................................................................................................................................14
5.2.1. DMX-512 Protocol .......................................................................................................................................14
5.2.2. DMX Cables .................................................................................................................................................15
5.2.3. Master/Slave Setup ....................................................................................................................................16
5.2.4. DMX Linking..................................................................................................................................................17
5.2.5. DMX Addressing..........................................................................................................................................18
5.3. Ethernet Connection .......................................................................................................................................18
5.3.1. Art-Net and Kling-Net Protocols...............................................................................................................18
5.3.2. Network Cables ..........................................................................................................................................18
5.3.3. Art-Net/Kling-Net Setup.............................................................................................................................19
5.3.4. Art-Net Settings ...........................................................................................................................................20
5.3.5. Kling-Net Settings ........................................................................................................................................20
5.3.6. Universe Numbering...................................................................................................................................21
6. Operation ...........................................................................................................................................................22
Safety Instructions for Operation...................................................................................................................22
Control Modes ..................................................................................................................................................22
Control Panel ....................................................................................................................................................23
Start-up...............................................................................................................................................................23
Menu Overview ................................................................................................................................................24
Main Menu Options .........................................................................................................................................25
DMX Address ...............................................................................................................................................25
Network Settings .........................................................................................................................................26
Set Manual/DHCP ..............................................................................................................................26
Set IP Address......................................................................................................................................26
Set Net Mask .......................................................................................................................................26
Control Modes ............................................................................................................................................27

3
Pixel Controller
Product code: 44510
Pixel Type .............................................................................................................................................27
Set Output ...........................................................................................................................................28
DMX.......................................................................................................................................................28
Art-Net ..................................................................................................................................................29
Kling-Net...............................................................................................................................................29
Slave .....................................................................................................................................................30
Auto ......................................................................................................................................................30
Manual .................................................................................................................................................31
Advanced Settings.....................................................................................................................................31
Signal Hold...........................................................................................................................................32
Pixel Reverse........................................................................................................................................32
Screen Timeout ...................................................................................................................................32
Screen Brightness................................................................................................................................32
Software Version.................................................................................................................................32
Invert Display .......................................................................................................................................32
Factory Reset ......................................................................................................................................32
DMX Channels ..................................................................................................................................................33
Pixelstrip 20/40 .............................................................................................................................................33
7 Channels...........................................................................................................................................33
120, 240, 360, 480 Channels .............................................................................................................34
480 Channels (Art-Net)......................................................................................................................35
960 Channels (Art-Net)......................................................................................................................36
1440 Channels (Art-Net)....................................................................................................................37
1920 Channels (Art-Net)....................................................................................................................38
Pixeltube 16/32............................................................................................................................................39
7 Channels...........................................................................................................................................39
96, 192, 288, 384, 480 Channels .......................................................................................................40
384 Channels (Art-Net)......................................................................................................................41
768 Channels (Art-Net)......................................................................................................................42
1152 Channels (Art-Net)....................................................................................................................43
1536 Channels (Art-Net)....................................................................................................................44
1920 Channels (Art-Net)....................................................................................................................45
PixelDot .........................................................................................................................................................46
7 Channels...........................................................................................................................................46
30, 60, 90, 120 Channels....................................................................................................................47
120 Channels (DMX and Art-Net)....................................................................................................48
240 Channels (DMX and Art-Net)....................................................................................................49
360 Channels (DMX and Art-Net)....................................................................................................50
480 Channels (DMX and Art-Net)....................................................................................................51
7. Troubleshooting .................................................................................................................................................52
8. Maintenance .....................................................................................................................................................53
Safety Instructions for Maintenance.............................................................................................................53
Preventive Maintenance................................................................................................................................53
Basic Cleaning Instructions .......................................................................................................................53
Corrective Maintenance................................................................................................................................53
8.3.1. Replacing the Fuse.....................................................................................................................................54
9. Deinstallation, Transportation and Storage ....................................................................................................55
Instructions for Deinstallation..........................................................................................................................55
Instructions for Transportation ........................................................................................................................55
Storage...............................................................................................................................................................55
10. Disposal ..............................................................................................................................................................55
11. Approval.............................................................................................................................................................55

4
Pixel Controller
Product code: 44510
1. Introduction
Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your
Highlite International dealer.
Your shipment includes:
●Showtec Pixel Controller
●Schuko to pro power cable (1,5 m)
●User manual
Fig. 01
Intended Use
This device is intended for use as a pixel controller. It is suitable only for indoor installation. It is not suitable
for households.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Product Lifespan
This device is not designed for permanent operation. Disconnect the device from the electrical power
supply when the device is not in operation. This will reduce the wear and will improve the device’s
lifespan.
Text Conventions
Throughout the user manual the following text conventions are used:
●Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons”
●References: References to chapters and parts of the device are in bold lettering, for example:
“Refer to 2. Safety”, “turn the adjustment handle (08)”
●0–255: Defines a range of values
●Notes: Note: (in bold lettering) is followed by useful information or tips

5
Pixel Controller
Product code: 44510
Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
Attention
Indicates important information for the correct operation and use of the
product.
Important
Read and observe the instructions in this document.
Electrical hazard
Provides important information about the disposal of this product.
Symbols on the Information Label
This product is provided with an information label. The information label is located at the backside of the
device.
The information label contains the following symbols:
This device is designed for indoor use.
This device shall not be treated as household waste.
This device falls under IEC protection class I.
Read and observe the instructions in the user manual.
Caution: Risk of electric shock. Disconnect input power before opening.
Warning: This appliance must be earthed.

6
Pixel Controller
Product code: 44510
2. Safety
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.
●Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach. Packaging material is a potential source of danger for children.
DANGER
Electric shock caused by dangerous voltage inside
There are areas within the device where dangerous touch voltage may be present.
●Do not open the device or remove any covers.
●Do not operate the device if the covers or the housing are open. Before operation, check if the
housing is firmly closed and all screws are tightly fastened.
●Disconnect the device from electrical power supply before service and maintenance, and when the
device is not in use.
DANGER
Electric shock caused by short-circuit
This device falls under IEC protection class I.
●Make sure that the device is electrically connected to ground (earth). Connect the device only to a
socket-outlet with ground (earth) connection.
●Do not cover the ground (earth) connection.
●Do not bypass the thermostatic switch or fuses.
●For replacement use fuses of the same type and rating only.
●Do not let the power cable come into contact with other cables. Handle the power cable and all
connections with the mains with caution.
●Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable.
●Make sure that the power cable is not crimped or damaged. Examine the power cable periodically
for any defects.
●Do not immerse the device in water or other liquids. Do not install the device in a location where
flooding may occur.
●Do not use the device during thunderstorms. Disconnect the device from the electrical power supply
immediately.

7
Pixel Controller
Product code: 44510
WARNING
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at
strobe lights.
Attention
Power supply
●Before connecting the device to the power supply, make sure that the current, voltage and
frequency match the input voltage, current and frequency specified on the information label on the
device.
●Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the
required power consumption of the device.
Attention
General safety
●Do not block the ventilation openings. Without proper heat dissipation and air circulation, the
internal components may overheat. This can result in product damage.
●Do not shake the device. Avoid brute force when installing or operating the device.
●If the device is dropped or struck, disconnect the device from the electrical power supply
immediately.
●If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it
on immediately. Let the device reach room temperature before switching it on, otherwise it may be
damaged by the formed condensation.
●If the device fails to work properly, discontinue the use immediately.
Attention
This device shall be used only for the purposes it is designed for.
This device is designed to be used as a pixel controller. Any incorrect use may lead to hazardous
situations and result in injuries and material damage.
This device does not contain user-serviceable parts. Unauthorized modifications to the device will render
the warranty void. Such modifications may result in injuries and material damage.

8
Pixel Controller
Product code: 44510
Attention
Before each use, examine the device visually for any defects.
Make sure that:
●All screws used for installing the device or parts of the device are tightly fastened and are not
corroded.
●The safety devices are not damaged.
●There are no deformations on housings, fixations and installation points.
●There is no damage to the RJ45 connectors.
●The CAT cables used for connection of the device are not damaged and do not show any material
fatigue.
●The power cables are not damaged and do not show any material fatigue.
Attention
Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater
than 12 mm, such as fingers, and no protection against harmful ingress of water.
Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried by ordinary persons.
Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite
International dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled
person, for specific tasks and work activities associated with the installation, service and maintenance of
this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards
associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons
include not only users of the product but also any other persons that may have access to the device or
who may be in the vicinity of the device.

9
Pixel Controller
Product code: 44510
3. Description of the Device
The Pixel Controller is suitable only for indoor installation (e.g. in hotels or theaters, in order to create a
good ambience in a lobby) and it can be used only with the Pixelstrips 20 and 40, Pixeltubes 16 and 32 or
PixelDots. Each controller can handle those devices divided over 4 outputs.
All Pixelstrips/Pixeltubes/PixelDots can be easily daisy-chained and connected to the Pixel Controller with
a CAT cable. The Pixel Controller can be controlled with DMX, Art-Net and Kling-Net. It can also be used
as a stand-alone controller with built-in programs. When using multiple devices, the built-in programs can
be synchronized due to master/slave function.
Front View
Fig. 02
Pro power connector (Blue) IN
Pro power connector (Gray) OUT
Fuse T6,3A/250 V
Power switch ON/OFF
OLED display + control buttons
Back View
Fig. 03
3-pin DMX connector OUT
5-pin DMX connector OUT
RJ45 connector Art-Net IN/OUT
RJ45 connector Art-Net IN/OUT
5-pin DMX connector IN
3-pin DMX connector IN
Dedicated RJ45 Pixelstrip/Pixeltube/Pixeldot connectors OUT 1–4

10
Pixel Controller
Product code: 44510
3.3. Side View
Fig. 04
13) Safety eye
Product Specifications
Model:
Pixel Controller
Electrical:
Input voltage:
100–240 V AC, 50/60 Hz
Power consumption:
230 W
Fuse:
T6,3A/250 V
Physical:
Dimensions:
342 x 210 x 68 mm (L x W x H)
Weight:
2,03 kg
Operation and control:
Control:
Auto, Manual, Master/Slave, DMX-512, Art-Net, Kling-Net
DMX channels:
See 6.7. DMX Channels on pages 33–51 for more information
Control protocols:
DMX-512, Art-Net, Kling-Net
Control panel:
OLED display and buttons
Connections:
Power connections:
Pro power connectors IN/OUT
Input connections:
3-pin/5-pin DMX connectors IN, 2 x Art-Net RJ45 connectors IN/OUT
Output connections:
3-pin/5-pin DMX connectors OUT, 4 x dedicated RJ45 connectors OUT
Maximum cable length:
10 m (CAT-5/CAT-6) from the Pixel Controller to the
Pixelstrip/Pixeltube/PixelDot
Maximum output length:
Pixelstrip 20/40: 4 m per output; 16 m per controller
Pixeltube 16/32: 5 m per output; 20 m per controller
PixelDot: 40 x PixelDot per output; 160 x PixelDot per controller
Construction:
Housing:
Metal
Color:
Black
IP rating:
IP20
Cooling:
Convection
Thermal:
Maximum ambient temperature ta:
40 °C
Maximum housing temperature tc:
70 °C

11
Pixel Controller
Product code: 44510
Compatibility
Attention
The Pixel Controller is designed to be operated ONLY with the Pixelstrip 20/40, Pixeltube
16/32 or PixelDot.
The Pixel Controller is delivered without the Pixelstrip/Pixeltube/PixelDot. You need to purchase these
devices separately.
Product code: 44501 (Pixelstrip 20, 50 cm)
Product code: 44502 (Pixelstrip 40, 100 cm)
Product code: 44520 (Pixeltube 32)
Product code: 44521 (Pixeltube 16)
Product code: 44530 (PixelDot)
Recommended Software
Product code: 50180 (Arkaos LED Master)
Product code: 102101 (Arkaos Media Master Express 5.0)
Product code: 102201 (Arkaos Media Master Pro 5.0)
Dimensions
Fig. 05

12
Pixel Controller
Product code: 44510
4. Installation
4.1. Safety Instructions for Installation
Attention
Make sure there is enough space for ventilation around the device.
●Do not block the ventilation openings. Without proper heat dissipation and air circulation, the
internal components may overheat. This can result in product damage.
●Do not install near equipment that produces heat, for example amplifiers.
Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and
site-specific regulations.
4.3. Installation Site Requirements
●The device must be installed only indoors.
●The device can be placed on a flat surface or mounted to any kind of truss, with clamps and/or
M5/M10 screws for fixed installations.
●The maximum ambient temperature ta= 40 °C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.
4.4. Rigging
The device can be positioned on a flat surface or mounted to a truss or other rigging structure. Make sure
that all loads are within the pre-determined limits of the supporting structure.
CAUTION
Restrict the access under the work area during rigging and/or derigging.
To mount the device, follow the steps below:
Use clamps to attach the device to the supporting structure, as shown in Fig. 06 on page 13. Make
sure that the device cannot move freely.
02) Secure the device with a secondary suspension, for example a safety cable. Make sure that the
secondary suspension can hold 10 times the weight of the device. If possible, the secondary
suspension should be attached to a supporting structure independent of the primary suspension. Put
the safety cable through the safety eye (13), as shown in Fig. 06 on page 13. You can use the safety
cable supplied with the device.
03) It is also possible to mount the device with 4 x M5 screws. Drill holes in the wall, place the controller on
the wall and tighten the screws.

13
Pixel Controller
Product code: 44510
Fig. 06
4.5. Connecting to Power Supply
DANGER
Electric shock caused by short-circuit
The device accepts AC mains power at 100–240 V and 50/60 Hz. Do not supply power at any other
voltage or frequency to the device.
This device falls under IEC protection class I. Make sure that the device is always electrically connected
to the ground (earth).
Before connecting the device to the socket-outlet:
●Make sure that the power supply matches the input voltage specified on the information label on
the device.
●Make sure that the socket-outlet has ground (earth) connection.
Connect the device to the socket-outlet with the power plug.

14
Pixel Controller
Product code: 44510
4.6. Power Linking of Multiple Devices
This device supports power linking. Power can be relayed to another device via the power OUT
connector. Note that the input and the output connectors have different designs: one type cannot be
connected to the other.
Power linking of multiple devices must be carried out only by instructed or skilled persons.
WARNING
Incorrect power linking may lead to overload of the electrical circuit and result in serious
injuries and damage of property.
To prevent overload of the electrical circuit, when power linking multiple devices:
●Use cables with sufficient current-carrying capacity. The power cable supplied with the device is not
suitable for power linking of multiple device.
●Make sure that the total current draw of the device and all connected devices does not exceed the
rated capacity of the power cables and the circuit breaker.
●Do not link more devices on one power link than the maximum recommended number.
Maximum recommended number of devices:
●at 100–120 V: 5 devices
●at 200–240 V: 10 devices
5. Setup
5.1. Warnings and Precautions
Attention
Connect all data cables before supplying power.
Disconnect power supply before connecting or disconnecting data cables.
5.2. DMX Connection
5.2.1. DMX-512 Protocol
You need a DMX serial data link to run light shows of one or more devices using a DMX-512 controller or
to run synchronized shows of two or more devices set in a master/slave operating mode.
The Pixel Controller has 3-pin and 5-pin DMX signal IN and OUT connectors.
The pin assignment is as follows:
●3-pin: pin 1 (ground), pin 2 (-), pin 3 (+)
●5-pin: pin 1 (ground), pin 2 (-), pin 3 (+), pin 4 (N/C), pin 5 (N/C)
Devices on a serial data link must be daisy-chained in a single line. The number of devices that you can
control on one data link is limited by the combined number of the DMX channels of the connected
devices and the 512 channels available in one DMX universe.
To comply with the TIA-485 standard, no more than 32 devices should be connected on one data link.
In order to connect more than 32 devices on one data link, you must use a DMX optically isolated
splitter/booster, otherwise this may result in deterioration of the DMX signal.
Note:
●Maximum recommended DMX data link distance: 300 m
●Maximum recommended number of devices on a DMX data link: 32 devices

15
Pixel Controller
Product code: 44510
5.2.2. DMX Cables
Shielded twisted-pair cables with 3-pin/5-pin XLR connectors must be used for reliable DMX connection.
You can purchase DMX cables directly from your Highlite International dealer or make your own cables.
If you use XLR audio cables for DMX data transmission, this may lead to signal degradation and unreliable
operation of the DMX network.
When you make your own DMX cables, make sure that you connect the pins and wires correctly as
shown in Fig. 07.
Fig. 07

16
Pixel Controller
Product code: 44510
5.2.3. Master/Slave Setup
The Pixel Controller supports master/slave control mode. You can connect the Pixelstrip 20/40 (max. 4 m
per output), Pixeltube 16/32 (max. 5 m per output) or PixelDots (max. 40 devices per output) to the Pixel
Controller. In the example below, the Pixelstrip 40 is connected to the Pixel Controller.
To connect multiple devices in master/slave setup, follow the steps below:
Connect the first device’s DMX OUT connector to the second device’s DMX IN connector with a 3-
pin/5-pin DMX cable.
Repeat step 1 to connect all devices as shown in Fig. 08.
Connect a DMX terminator (120 Ω resistor) to the DMX OUT connector of the last device in the setup.
Set the first device on the data link as a master device. See 6.6.3.6. Slave on page 30 for more
information.
Set the remaining devices as slave devices. See 6.6.3.6. Slave on page 30 for more information.
Fig. 08

17
Pixel Controller
Product code: 44510
5.2.4. DMX Linking
You can connect the Pixelstrip 20/40 (max. 4 m per output), Pixeltube 16/32 (max. 5 m per output) or
PixelDots (max. 40 devices per output) to the Pixel Controller. In the example below, the Pixelstrip 40 is
connected to the Pixel Controller.
To connect multiple devices on one DMX data link, follow the steps below:
Use a 3-pin/5-pin DMX cable to connect the DMX OUT connector of the lighting controller to the
DMX IN connector of the first device.
Connect the first device’s DMX OUT connector to the second device’s DMX IN connector with a
3-pin/5-pin DMX cable.
Repeat step 2 to connect all devices in a daisy-chain as shown in Fig. 09.
Connect a DMX terminator (120 Ω resistor) to the DMX OUT connector of the last device on the data
link.
Fig. 09

18
Pixel Controller
Product code: 44510
5.2.5. DMX Addressing
In a setup with multiple devices, make sure that you set the DMX starting address of each device
correctly. The Pixel Controller has many different personalities, depending on what device is connected
to it: Pixelstrip, Pixeltube or PixelDot. For example, if you want to connect multiple Pixel Controllers on one
data link and use them in 7-channel mode, follow the steps below:
Set the starting address of the 1st device on the data link to 1 (001).
Set the starting address of the 2nd device on the data link to 8 (008), as 1 + 7 = 8.
Set the starting address of the 3rd device on the data link to 15 (015) as 8 + 7 = 15.
Continue assigning the starting addresses of the remaining devices by adding each time 7 to the
previous number.
Make sure that you do not have any overlapping channels in order to control each Pixel Controller
correctly. If two or more devices are addressed similarly, they will work similarly.
5.3. Ethernet Connection
Attention
Connect all data cables before supplying power.
Disconnect power supply before connecting or disconnecting data cables.
5.3.1. Art-Net and Kling-Net Protocols
Art-Net is a protocol that uses TCP/IP to transfer large amount of DMX-512 data over an Ethernet network.
Art-Net 4 can support up to 32768 universes. Art-Net™ Designed by and Copyright Artistic Licence
Holdings Ltd.
Kling-Net is a protocol that allows the creation of a network of LED devices, which are automatically
configured. Kling-Net is independent of DMX-512 or Art-Net protocols. It uses a standard Ethernet
network.
5.3.2. Network Cables
Standard twisted-pair Ethernet cables (CAT-5/CAT-5E/CAT-6) can be used to connect the device to a
computer or to a lighting controller that supports Art-Net or Kling-Net.
If you make your own network cables, make sure that you connect the pins and wires correctly as shown
in Fig. 10. Use RJ45 (8P8C) connectors and patch the cables according to the T568B color standard.
Fig. 10

19
Pixel Controller
Product code: 44510
5.3.3. Art-Net/Kling-Net Setup
The Pixel Controller has 2 RJ45 connectors. Either connector can be used as an input and as throughput.
You can connect the Pixelstrip 20/40 (max. 4 m per output), Pixeltube 16/32 (max. 5 m per output) or
PixelDots (max. 40 devices per output) to the Pixel Controller. In the example below, the Pixelstrip 40 is
connected to the Pixel Controller.
To connect multiple devices in an Art-Net/Kling-Net setup, follow the steps below:
Use a CAT-5/CAT-5E/CAT-6 cable to connect the RJ45 connector of the computer/lighting controller
to one of the RJ45 connectors of the first device.
Connect the other RJ45 connector of the first device to the RJ45 connector of the second device
with a CAT-5/CAT-5E/CAT-6 cable.
Repeat step 2 to connect all devices as shown in Fig. 11.
Fig. 11