Show Tec Eventlite 177IR User manual

EventLITE 177IR V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 44010
MANUAL
ENGLISH

1
Ordercode: 44010
EventLITE 177IR
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Rigging ............................................................................................................................................................................4
Connection with the mains.........................................................................................................................................5
Return Procedure..........................................................................................................................................................6
Claims..............................................................................................................................................................................6
Description of the device.................................................................................................................................................7
Optional accessories....................................................................................................................................................7
Frontside..........................................................................................................................................................................8
Backside .........................................................................................................................................................................9
Installation...........................................................................................................................................................................9
Set Up and Operation .......................................................................................................................................................9
Charging the built-in battery....................................................................................................................................10
Control Modes.............................................................................................................................................................10
One EventLITE (Built-in programs, Auto mode and Static color mode)........................................................10
One EventLITE (Sound mode)................................................................................................................................10
Multiple EventLITEs (Master/Slave control)..........................................................................................................11
Multiple EventLITEs (DMX Control) ........................................................................................................................12
Fixture Linking...............................................................................................................................................................13
Data Cabling...............................................................................................................................................................13
Control Panel ...............................................................................................................................................................14
Control Mode ..............................................................................................................................................................14
DMX Addressing ..........................................................................................................................................................14
Menu Overview...........................................................................................................................................................15
Main Menu Options....................................................................................................................................................16
1. Built-in programs ..................................................................................................................................................16
2. Auto Run Program ...............................................................................................................................................17
3. Sound control mode...........................................................................................................................................17
4. DMX Addressing/ DMX configuration..............................................................................................................17
5. Slave Mode...........................................................................................................................................................17
6. Static Color Mode ...............................................................................................................................................18
7. Eco Mode..............................................................................................................................................................18
Optional remote control ...........................................................................................................................................18
1. Built-in Auto Show ................................................................................................................................................20
2. Built-in programs ..................................................................................................................................................20
3. Sound-controlled mode.....................................................................................................................................20
4. Dimming mode ....................................................................................................................................................20
5. Color mode ..........................................................................................................................................................20
DMX Channels .............................................................................................................................................................21
2 channels .................................................................................................................................................................21
3 channels .................................................................................................................................................................21
5 channels .................................................................................................................................................................21
Maintenance....................................................................................................................................................................22
Replacing the Fuse.....................................................................................................................................................22
Troubleshooting ...............................................................................................................................................................22
No Light.........................................................................................................................................................................22
No Response to DMX..................................................................................................................................................22
Product Specifications....................................................................................................................................................24
Dimensions........................................................................................................................................................................25
Notes ..................................................................................................................................................................................26

2
Ordercode: 44010
EventLITE 177IR
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
Showtec EventLITE 177IR
IEC power cable (1,5 m)
User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual

3
Ordercode: 44010
EventLITE 177IR
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
•Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
•Never remove warning or informative labels from the unit.
•Never use anything to cover the ground contact.
•Never lift the fixture holding it by the projector-head, as the mechanics may be damaged. Always
hold the fixture by the transport handles.
•Never place any material over the lens.
•Never look directly into the light source.
•Never leave any cables lying around.
•Do not insert objects into air vents.
•Do not connect this device to a dimmerpack.
•Do not switch the device on and off in short intervals, as this will reduce the device’s life.
•Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the fixture to cool for at least 5 minutes before handling.
•Do not shake the device. Avoid brute force when installing or operating the device.
•Only use the device indoors, avoid contact with water or other liquids.
•Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
•Only operate the device after having familiarized with its functions.
•Avoid flames and do not put close to flammable liquids or gases.
•Always keep the case closed while operating.
•Always allow a free air space of at least 50 cm around the unit for ventilation.
•Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
•Make sure that the device is not exposed to extreme heat, moisture or dust.
•Make sure that the available voltage is not higher than stated on the rear panel.
•Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
•If the lens is obviously damaged, it has to be replaced.
•If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
•If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
•If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
•For adult use only. The fixture must be installed beyond the reach of children. Never leave the unit
running unattended.
•Never attempt to bypass the thermostatic switch or fuses.
•For replacement use fuses of same type and rating only.

4
Ordercode: 44010
EventLITE 177IR
•The user is responsible for correct positioning and operating of the EventLITE 177IR. The manufacturer
will not accept liability for damages caused by the misuse or incorrect installation of this device.
•This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
•Repairs, servicing and electric connection must be carried out by a qualified technician.
•WARRANTY: Till one year after date of purchase.
Note: WARRANTY on batteries is only 6 months after date of purchase.
When your battery remains dead after fully charging or it doesn’t function or doesn’t charge
anymore, you can order a new battery. The spare part number for the battery is SPTOP252.
Operating Determinations
•This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
•The minimum distance between light output and the illuminated surface must be bigger than 1
meter.
•The maximum ambient temperature ta= 40°C must never be exceeded.
•The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
•If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
•Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
•If the EventLITE 177IR is lowered from the ceiling or high joists, professional trussing systems have to be
used.
•Use a clamp to mount the EventLITE 177IR, with the mounting bracket, to the trussing system.
•The EventLITE 177IR must never be fixed swinging freely in the room.
•The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
•When rigging, derigging or servicing the EventLITE 177IR, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.

5
Ordercode: 44010
EventLITE 177IR
The EventLITE 177IR can be placed on a flat stage floor or mounted to any kind of truss with a clamp.
Improper installation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!

6
Ordercode: 44010
EventLITE 177IR
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of
the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement from which the obligation is resulting.

7
Ordercode: 44010
EventLITE 177IR
Description of the device
Features
The Showtec EventLITE 177IR is a compact, lightweight and powerful mobile spot. The special led-matrix
and very precise electronics ensures a smooth color mixing.
Compact size
Long battery life
Built-in battery charger and protection
Smooth color mixing
Input voltage: 100-240V AC, 50/60Hz
Power consumption: 30W
DMX linking: 30 pcs
Runtime: 6 hrs at full RGB on
Charging Cycle: 10 hrs (LED blackout when charging)
Spare battery: SPTOP252
DMX channels: 2, 3 or 5 channels
4-digit LED display for easy setup
Light source: 177x 10mm (60xR, 60xG, 57xB) LEDs
Light output: 700 lux @ 2m
Color Range: 16,7 million additive RGB colors
Control modes: Built-in programs, Auto run, DMX, Master/Slave, Sound-controlled, Static colors
Control protocol: DMX-512
Dimmer: 0-100%
Strobe: 0-20Hz
Protection rate: IP-20
Beam Angle: 30°
Housing: ABS plastic
Connections: IEC IN & 3-pin XLR IN & OUT
Cooling: Convection
Operation Temperature: -20°C ~40°C
Fuse: T1L/250V
Dimensions: 290 x 110 x 285 mm (LxWxH)
Weight: 2,06 kg
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
44002 UR-5 Universal IR Remote

8
Ordercode: 44010
EventLITE 177IR
Frontside
Fig. 01
01) Adjustment screw
02) Mounting bracket
03) 177x 10mm (60xR, 60xG, 57xB) LEDs

9
Ordercode: 44010
EventLITE 177IR
Backside
Fig. 02
04) 3-pin DMX signal connector OUT
05) 4-digit LED display + menu buttons
06) Power switch ON/OFF
07) Battery level indicator
08) 3-pin DMX signal connector IN
09) IEC power connector IN + Fuse T1L/250V
Installation
Remove all packing materials from the EventLITE 177IR. Check if all foam and plastic padding is removed.
Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.

10
Ordercode: 44010
EventLITE 177IR
Charging the built-in battery
01) In order to charge the battery, you need the included IEC power cable.
02) Turn off the power.
03) Connect the IEC power cable to the EventLITE 177IR.
04) Then plug the other end of the IEC power cable into a proper electric power supply socket.
05) While the battery is charging, the Red LED from the battery level indicator will light up and the Green
LEDs from the battery level indicator will light up in sequence.
06) When the battery is fully charged, all the Green LEDs from the battery level indicator will light up.
Important!
•Do not charge for more than 24 hours.
•Recharge within 3 days of use.
•Turn off the power with the power switch, when charging the battery!
Control Modes
There are 6 modes:
•Built-in programs
•Auto mode
•Static color mode
•Sound mode
•Master/Slave
•DMX-512 (2CH, 3CH, 5CH)
One EventLITE (Built-in programs, Auto mode and Static color mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the EventLITE is not connected with a DMX cable, it functions as a stand-alone device.
Please see pages 16-18 for more information about the Built-in programs, Auto mode and Static
color mode.
One EventLITE (Sound mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Turn on the music. If the device is set to Sound mode, then the EventLITE will react to the beat of the
music. Please see page 17 for more information about the Sound mode.

11
Ordercode: 44010
EventLITE 177IR
Multiple EventLITEs (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the EventLITEs and other devices.
The pins:
01) Earth
02) Signal -
03) Signal +
04) Link the units as shown in Fig. 03. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.
You can use the same functions on the master device as described on pages 16-18 (Built-in
programs, Auto mode, Static color mode or Sound mode). This means that you can set your desired
operation mode on the master device and all slave devices will react the same as the master
device.
Multiple EventLITEs (Master/Slave control)
Fig. 03

12
Ordercode: 44010
EventLITE 177IR
Multiple EventLITEs (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the EventLITEs and other devices.
04) Link the units as shown in Fig. 04. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.
05) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
Multiple EventLITEs DMX Set Up
Fig. 04
Note : Link all cables before connecting electric power

13
Ordercode: 44010
EventLITE 177IR
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
•DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
•DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
•DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
•DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30.
The EventLITE 177IR can be operated with a controller in control mode or without the controller in
stand-alone mode.

14
Ordercode: 44010
EventLITE 177IR
Control Panel
A) LED display
B) MODE button
C) SETUP button
D) UP button
E) DOWN button
Fig. 05
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address, next time.)
DMX Addressing
The control panel on the backside of the device allows you to assign DMX fixture addresses, which is the
first channel with which the EventLITE will respond to the controller.Please note, when you use the
controller, the unit has 5channels.
When using multiple EventLITEs, make sure you set the DMX addresses right. Therefore, the DMX address
of the first EventLITE should be 1(d001); the DMX address of the second EventLITE should be 1+5=6 (d006);
the DMX address of the third EventLITE should be 6+5=11 (d011), etc. Please, be sure that you do not
have any overlapping channels in order to control each EventLITE correctly. If two or more EventLITEs are
addressed similarly, they will work similarly.
Controlling:
After having addressed all EventLITEs, you may now start operating these via your lighting controller.
Note: After switching on, the EventLITE will automatically detect whether DMX 512 data is received or
not. If there is no data received at the DMX-input, the “LED“ on the control panel will not flash.
The problem may be:
•The XLR cable from the controller is not connected with the input of the EventLITE.
•The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 25 seconds
When no button is pressed for 25 seconds, the display will turn off.
To light up the display, you have to press the MODE, SETUP, UP or DOWN button.
Once you have pressed the button, the display will light up.
Lock mode after 60 seconds
Display board will blackout and show if there is no operation within 60s. Press the MODE and
DOWN button simultaneously for 3s at least to unlock the display board.

15
Ordercode: 44010
EventLITE 177IR
Menu Overview

16
Ordercode: 44010
EventLITE 177IR
Main Menu Options
Built-in programs
Auto run
Sound-controlled Mode
DMX address / DMX configuration
Master-Slave
Static Color Mode
Eco Mode
1. Built-in programs
With this menu you can set the built-in programs.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open this menu.
03) You can use the UP/DOWN buttons to scroll through the 9 built-in programs.
04) When you select menu , you can choose 8 preset colors and blackout. Press SETUP to enter
and choose one with the UP/DOWN buttons.
05) Press the SETUP button again to open the next menu. You can set the strobe frequency with the
UP/DOWN buttons between .
06) Press the SETUP button again and use the UP/DOWN buttons until the display shows .
07) Use the UP/DOWN buttons to scroll between .
08) In menu , you can switch between the strobe frequency and the Program
Running Speed by pressing the SETUP button.
09) Use the UP/DOWN buttons to change the values.
Speed from 00-99 and FL.
Strobe frequency from 00- 99 and FL.

17
Ordercode: 44010
EventLITE 177IR
2. Auto Run Program
With this menu you can set the Auto run mode of the EventLITE 177IR.
01) Press the MODE button on the device until the display shows .
02) The EventLITE will immediately start the Auto Run program.
03) Press the SETUP button to enter the menu.
04) With you can set the speed of the Auto program.
05) With you can set the strobe frequency.
06) With you can set the number of repetitions of each step of the Auto run
program.
07) You can scroll through these options with the SETUP button.
08) With the UP/DOWN buttons you can adjust the options.
3. Sound control mode
With this menu you can set the sensitivity of the sound mode.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open this menu.
03) Press the UP/DOWN buttons to change the sensitivity of the sound control mode between
, from low to high sound sensitivity.
04) Sound-controlled mode is now active and the device will react to the beat of the background
music.
4. DMX Addressing/ DMX configuration
With this menu you can set the DMX address and choose a DMX configuration.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open this menu. You can choose 512 different DMX addresses.
03) Use the UP/DOWN buttons to select the required address from .
Once you have set the desired DMX address, you can also choose the desired DMX Mode.
04) Press the SETUP button again to choose one of the 3 different DMX Modes. Use the UP/DOWN buttons
to select 2, 3 or 5 channels in DMX mode.
5. Slave Mode
With this menu you can set the device as a Slave.
01) Press the MODE button until the display shows .
02) If the device has not been set to slave, it is automatically classified as a master device. All slave
devices will follow the master movement. If the device has been set to slave, it will react the same as
its master device.

18
Ordercode: 44010
EventLITE 177IR
6. Static Color Mode
With this menu you can manually set a desired color.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open this menu.
03) You can use the SETUP button to scroll through 3 color options and also set the strobe frequency.
04) Use the UP/DOWN buttons to change the values.
Gradual adjustment Red (0-255)
Gradual adjustment Green (0-255)
Gradual adjustment Blue (0-255)
Strobe Frequency (0-99 and FL)
05) You can combine Red, Green and Blue to create an infinite range of colors (0-255).
7. Eco Mode
With this menu you can set the EventLITE 177IR to its economy mode.
01) Press the MODE button until the display shows .
02) Use the UP/DOWN buttons to choose between normal mode and economy mode.
03) When you choose “E - OFF” the EventLITE 177IR will have 100% of the luminance, this is the normal
mode.
04) When you choose “E - ON” the EventLITE 177IR will have 70% of the luminance, this is the economy
mode.
Optional remote control

19
Ordercode: 44010
EventLITE 177IR
Button
Function
Description
On / Off
Switch the device ON or OFF
Auto Mode
Activate Built-in Auto Show mode
Program Mode
Activate Built-in Programs Show mode
Sound-controlled Mode
Activate Sound-controlled mode
Speed Mode
Activate Speed Mode
Strobe Mode
Activate Strobe Mode
Dimming Mode
Activate Dimming Mode
Plus
Increase value button
Minus
Decrease value button
Red
Activate the Red color
Green
Activate the Green color
Blue
Activate the Blue color
Amber
Activate the Amber color
White
Activate the White color
Cyan
Activate the Cyan color
Purple
Activate the Purple color
Purplish red
Activate the Purplish red color
Orange
Activate the Orange color
White
Activate the White color
Bright pink
Activate the Bright pink color
Light green
Activate the Light green color
Water blue
Activate the Water blue color
Yellow
Activate the Yellow color
Warm white
Activate the Warm white color