Show Tec Helix M1100 Q4 Mobile User manual

Helix M1100 Q4 Mobile
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Product code: 43750
Firmware version: 2.3
USER MANUAL
ENGLISH
V1

1
Helix M1100 Q4 Mobile
Product code: 43750
Preface
Thank you for purchasing this Showtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.
This user manual contains information concerning:
●Safety instructions
●Intended and non-intended use of the device
●Installation and operation of the device
●Maintenance procedures
●Troubleshooting
●Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of
property.
©2022 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written
consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document and other language versions, please visit our website
www.highlite.com or contact us at [e-mail].
Highlite International and its authorized service providers are not liable for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or
reliance on the information contained in this document.

2
Helix M1100 Q4 Mobile
Product code: 43750
Table of contents
1. Introduction..........................................................................................................................................................4
Before Using the Product ..................................................................................................................................4
Intended Use .......................................................................................................................................................4
Product Lifespan.................................................................................................................................................4
LEDs Lifespan .......................................................................................................................................................4
Text Conventions ................................................................................................................................................5
Symbols and Signal Words................................................................................................................................5
Symbols on the Information Label ..................................................................................................................6
2. Safety ....................................................................................................................................................................7
Warnings and Safety Instructions ....................................................................................................................7
Requirements for the User.................................................................................................................................9
3. Description of the Device.................................................................................................................................10
Front View ..........................................................................................................................................................10
Bottom View......................................................................................................................................................11
3.3. Accessories........................................................................................................................................................11
Product Specifications ....................................................................................................................................12
3.5. Dimensions.........................................................................................................................................................13
4. Installation ..........................................................................................................................................................14
Safety Instructions for Installation ..................................................................................................................14
Personal Protective Equipment .....................................................................................................................14
Installation Site Requirements ........................................................................................................................14
Installing the Beamshapers (43745/43746/43747/43748)..........................................................................14
Installing the Barndoor (43742) ......................................................................................................................16
Installing the Tophat (43741) ..........................................................................................................................17
Rigging ...............................................................................................................................................................18
Angle Adjustment.......................................................................................................................................19
Charging the Battery.......................................................................................................................................20
Connecting to Power Supply.........................................................................................................................21
Power Linking of Multiple Devices ...........................................................................................................21
5. Setup ...................................................................................................................................................................22
Warnings and Precautions .............................................................................................................................22
Stand-alone Setup ...........................................................................................................................................22
DMX Connection..............................................................................................................................................22
DMX-512 Protocol .......................................................................................................................................22
DMX Cables .................................................................................................................................................23
Master/Slave Setup ....................................................................................................................................23
DMX Linking..................................................................................................................................................24
DMX Addressing..........................................................................................................................................24
Multiple Helixes (Wireless DMX Control)..................................................................................................25
Sweden 2.4GHz Wireless Communication Module .....................................................................25
Wireless DMX Connection ................................................................................................................25
Wireless DMX Problems......................................................................................................................25
Connect the Helix to the Wireless DMX Signal Transmitter .........................................................26
Disconnect the Helix from the Wireless DMX Signal Transmitter ................................................26
Setup Example 1.................................................................................................................................26
Setup Example 2.................................................................................................................................27
6. Operation ...........................................................................................................................................................28
Safety Instructions for Operation...................................................................................................................28
Turning On/Off ..................................................................................................................................................28
Factory Reset ....................................................................................................................................................28
Control Modes ..................................................................................................................................................29
Control Panel ....................................................................................................................................................30
Start-up...............................................................................................................................................................30

3
Helix M1100 Q4 Mobile
Product code: 43750
Menu Overview ................................................................................................................................................31
Main Menu Options .........................................................................................................................................33
DMX Settings ................................................................................................................................................33
DMX Address .......................................................................................................................................33
Channels ..............................................................................................................................................34
DMX Signal...........................................................................................................................................34
W-DMX Unlock ....................................................................................................................................34
Manual Mode .............................................................................................................................................35
Auto Mode...................................................................................................................................................35
Built-in Programs Mode..............................................................................................................................36
Program 01 / Static Colors................................................................................................................36
Program 02-16.....................................................................................................................................36
Slave Mode..................................................................................................................................................37
Settings..........................................................................................................................................................37
AC Power Loss.....................................................................................................................................37
Curves Select ......................................................................................................................................38
Dimmer Speed ....................................................................................................................................38
DMX Fail................................................................................................................................................39
Working Time .......................................................................................................................................39
DMX Sync.............................................................................................................................................40
Lock.......................................................................................................................................................40
Calibration...........................................................................................................................................41
Delayed Output .................................................................................................................................41
Factory Reset ......................................................................................................................................42
Information...................................................................................................................................................42
DMX Channels ..................................................................................................................................................43
4 channels....................................................................................................................................................43
6 channels....................................................................................................................................................43
10 channels..................................................................................................................................................43
RDM Information .........................................................................................................................................45
RDM Details..............................................................................................................................................45
Supported RDM PIDs (Parameter IDs) ................................................................................................45
Highlite RDM Details ...............................................................................................................................45
7. Troubleshooting .................................................................................................................................................46
8. Maintenance .....................................................................................................................................................47
Safety Instructions for Maintenance.............................................................................................................47
Preventive Maintenance................................................................................................................................47
Basic Cleaning Instructions .......................................................................................................................47
Draining Condensation Water .................................................................................................................48
Corrective Maintenance................................................................................................................................48
9. Deinstallation, Transportation and Storage ....................................................................................................49
Instructions for Deinstallation..........................................................................................................................49
Instructions for Transportation ........................................................................................................................49
Storage...............................................................................................................................................................49
10. Disposal ..............................................................................................................................................................50
11. Approval.............................................................................................................................................................50

4
Helix M1100 Q4 Mobile
Product code: 43750
1. Introduction
Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your
Highlite International dealer.
Your shipment includes:
●Showtec Helix M1100 Q4 Mobile
●Schuko to True1 pro power cable (1,5 m)
●1 x safety cable
●1 x quick-lock bracket
●User manual
Fig. 01
Intended Use
This device is intended for professional use as an outdoor wash. It is not suitable for households and for
general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Product Lifespan
This device is not designed for permanent operation. Disconnect the device from the electrical power
supply when the device is not in operation. This will reduce the wear and will improve the device’s
lifespan.
LEDs Lifespan
The light output of the LEDs gradually decreases over time (lumen depreciation). High operating
temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate
ventilation and operating the LEDs at the lowest possible brightness.

5
Helix M1100 Q4 Mobile
Product code: 43750
Text Conventions
Throughout the user manual the following text conventions are used:
●Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons”
●References: References to chapters and parts of the device are in bold lettering, for example:
“Refer to 2. Safety”, “turn the adjustment handle (05)”
●0–255: Defines a range of values
●Notes: Note: (in bold lettering) is followed by useful information or tips
Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
Attention
Indicates important information for the correct operation and use of the
product.
Important
Read and observe the instructions in this document.
Electrical hazard
Provides important information about the disposal of this product.

6
Helix M1100 Q4 Mobile
Product code: 43750
Symbols on the Information Label
This product is provided with an information label. The information label is located on the mounting
bracket of the device.
The information label contains the following symbols:
This device shall not be treated as household waste.
Read and follow the instructions in the user manual before installing, operating or
servicing the device.
This device is rated IP65.
This device falls under IEC protection class I.
Replace any cracked protective shield.
Caution: Risk of electric shock. Do not open.
Caution: To reduce the risk of electrical shock, do not remove cover. No user-
serviceable parts inside. Refer servicing to qualified personnel.
This device contains a battery.

7
Helix M1100 Q4 Mobile
Product code: 43750
2. Safety
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.
●Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach. Packaging material is a potential source of danger for children.
DANGER
Risk of explosion caused by incorrect handling
This device contains a built-in rechargeable lithium-ion battery. The battery is not replaceable. The
battery may explode or cause burns if it is crushed, disassembled or exposed to fire or high temperatures.
●Do not open the device and do not attempt to remove the built-in battery.
●Do not disassemble the battery.
●Do not crush or puncture the battery.
●Do not short-circuit the battery.
●Do not expose the battery to water or other liquids.
●Keep the battery away from fire and heat.
DANGER
Electric shock caused by dangerous voltage inside
There are areas within the device where dangerous touch voltage may be present.
●Do not open the device or remove any covers.
●Do not operate the device if the covers or the housing are open. Before operation, check if the
housing is firmly closed and all screws are tightly fastened.
●Disconnect the device from electrical power supply before service and maintenance, and when the
device is not in use.

8
Helix M1100 Q4 Mobile
Product code: 43750
DANGER
Electric shock caused by short-circuit
This device falls under IEC protection class I.
●Make sure that the device is electrically connected to ground (earth). Connect the device only to a
socket-outlet with ground (earth) connection.
●Do not cover the ground (earth) connection.
●Do not bypass the thermostatic switch or fuses.
●Do not let the power cable come into contact with other cables. Handle the power cable and all
connections with the mains with caution.
●Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable.
●Make sure that the power cable is not crimped or damaged. Examine the power cable periodically
for any defects.
●Do not immerse the device in water or other liquids. Do not install the device in a location where
flooding may occur.
●Do not use the device during thunderstorms. Disconnect the device from the electrical power supply
immediately.
●Keep the connectors sealed with the rubber caps when the connectors are not in use.
●Do not connect the cables from above the connectors, if the device is installed outdoors. Make a
‘drip loop’ in the cable so that rain water cannot enter the device.
WARNING
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at
strobe lights.
Attention
Power supply
●Before connecting the device to the power supply, make sure that the current, voltage and
frequency match the input voltage, current and frequency specified on the information label on the
device.
●Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the
required power consumption of the device.
Attention
General safety
●Do not connect the device to a dimmer pack.
●Do not switch the device on and off in short intervals. This decreases the device’s life.
●Do not shake the device. Avoid brute force when installing or operating the device.
●Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is
impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for
more information, as servicing can be performed only by instructed or skilled persons.
●If the device is dropped or struck, disconnect the device from the electrical power supply
immediately.

9
Helix M1100 Q4 Mobile
Product code: 43750
●If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it
on immediately. Let the device reach room temperature before switching it on, otherwise it may be
damaged by the formed condensation.
●If the device fails to work properly, discontinue the use immediately.
Attention
For professional use only
This device shall be used only for the purposes it is designed for.
This device is designed to be used as a professional outdoor wash. Any incorrect use may lead to
hazardous situations and result in injuries and material damage.
●This device is not suitable for households and for general lighting.
●This device is not designed for permanent operation.
●This device does not contain user-serviceable parts. Unauthorized modifications to the device will
render the warranty void. Such modifications may result in injuries and material damage.
Attention
Before each use, examine the device visually for any defects.
Make sure that:
●All screws used for installing the device or parts of the device are tightly fastened and are not
corroded.
●The safety devices are not damaged.
●There are no deformations on housings, fixations and installation points.
●The lens is not cracked or damaged.
●The power cables are not damaged and do not show any material fatigue.
Attention
Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP65 rated. IP (Ingress Protection) 65 class means that the device is dust-tight and protected
against harmful effect of water jets.
Keep the connectors sealed with the rubber caps when the connectors are not in use.
Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried by ordinary persons.
Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite
International dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled
person, for specific tasks and work activities associated with the installation, service and maintenance of
this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards
associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons
include not only users of the product but also any other persons that may have access to the device or
who may be in the vicinity of the device.

10
Helix M1100 Q4 Mobile
Product code: 43750
3. Description of the Device
The Showtec Helix M1100 Q4 Mobile is a battery powered 8 x 10 W RGBW LED Wash with IP65 rating,
suitable for mobile and outdoor applications. It is the follow-up of the Helix M1000 Q4 Mobile and
equipped with a 10-15% brighter LED. Its 10° beam angle can be widened to a 20°, 40°, 15°x60°, or 90°
beam angle by using optionally available dedicated beam shapers. Equipped with a rechargeable
lithium-ion battery, the Helix M1100 Q4 Mobile will operate up to 15 hours without charging. The tilt angle
can be manually adjusted over 180° and the unit can be controlled via W-DMX (wireless), DMX,
Master/Slave, Manual, and Auto mode with many built-in programs.
It has an emergency backup function, which switches the output to 4000 K white at maximum brightness
in case the mains power drops. Its delayed output function allows you to program the unit and have it
start later, saving precious battery runtime. This can be very helpful when setting up mid-day and having
it turn on automatically at night. The Helix M1100 Q4 comes with a 1.5-metre powerCON TRUE1 cable,
Quick-Lock bracket, and Safety Cable.
Front View
Fig. 02
01) 8 x Prolight Opto RGBW 4-in-1 10 W LEDs
02) 2x Adjustment screws
03) 100–240 V True1 pro power connector IN
04) 100–240 V True1 pro power connector OUT
05) 5-pin DMX connector OUT
06) 5-pin DMX connector IN
07) OLED display + control buttons

11
Helix M1100 Q4 Mobile
Product code: 43750
Bottom View
Fig. 03
08) Protective valve
09) 2x Quick Locks
10) Power switch ON/OFF (for battery operation)
Press this switch for the light output to be visible. The current from the built-in battery is responsible for
the light output. The True1 pro power cable should be used only when charging the battery.
3.3. Accessories
The device is delivered without a barndoor, beamshaper or tophat. There are several accessories for this
device:
●Product code: 43742 –Barndoor for Helix M1000 Q4 Mobile
●Product code: 43745 –Beamshaper for Helix M1000 Q4 Mobile (20°)
●Product code: 43746 –Beamshaper for Helix M1000 Q4 Mobile (40°)
●Product code: 43747 –Beamshaper for Helix M1000 Q4 Mobile (15°x60°)
●Product code: 43748 –Beamshaper for Helix M1000 Q4 Mobile 90°
●Product code: 43741 –Tophat for Helix M1000 Q4 Mobile
●Product code: 52001 –W-DMX™ BlackBox F-1 Tranceiver G6
●Product code: D7229 –Case for 4x Helix M1000

12
Helix M1100 Q4 Mobile
Product code: 43750
Product Specifications
Model:
Helix M1100 Q4 Mobile
Electrical:
Input voltage:
100–240 V AC, 50/60 Hz
Power consumption:
75 W
Physical:
Dimensions:
367 x 126 x 307 mm mm (L x W x H) (including bracket)
Weight:
7,9 kg
Optics:
Light source:
8 x RGBW 4-in-1 10 W LEDs
Light output
8800 lm
Refresh rate:
12000 Hz
Beam angle:
10° horizontal + 10° vertical (optional 20°, 40°, 15°x60° beamshapers)
Dimmer:
0–100 %
Strobe:
0–20 Hz
Dim curves:
4
Tilt angle:
0–180°
Battery:
Lithium-ion
Battery voltage:
18,5 V
Battery storage:
13 Ah
Battery life time:
8 h @ Full, 15 h by software
Charging cycle:
6 h
Rigging:
Quick-locks for fast rigging and mounting
Wireless DMX:
Wireless Solutions
IP rating:
IP65
DMX control:
via standard DMX controller
Onboard:
OLED Graphical display with 4 touch buttons
Operation and control:
Control:
Auto, Built-in programs, Manual, Master/Slave, DMX512, W-DMX, RDM
DMX channels:
4, 6 or 10 channels
Control panel:
LCD display and buttons
Connections:
Power connections:
IP65-rated Seetronic power connectors IN/OUT
Data connections:
IP65-rated 5-pin DMX connectors IN/OUT
Signal pinouts:
Pin 1 (earth), pin 2 (-), pin 3 (+), pin 4 (N/C), pin 5 (N/C)
Construction:
Housing:
Die-cast aluminum
Color:
Black
IP rating:
IP65
Cooling:
Convection
Thermal:
Maximum ambient temperature ta:
45 °C
Minimum ambient temperature:
-10 °C
Minimum distance:
Minimum distance from flammable surfaces:
0,8 m
Minimum distance to lighted object:
0,8 m

13
Helix M1100 Q4 Mobile
Product code: 43750
3.5. Dimensions
Fig. 04
Fig. 05

14
Helix M1100 Q4 Mobile
Product code: 43750
4. Installation
Safety Instructions for Installation
WARNING
Incorrect installation can cause serious injuries and damage of property.
If trussing systems are used, installation must be carried out only by instructed or skilled persons.
Follow all applicable European, national and local safety regulations concerning rigging and trussing.
Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and
site-specific regulations.
Installation Site Requirements
●The device can be used outdoors.
●The device can be mounted to a truss or other rigging structure in any orientation.
●The minimum distance between the light output and the illuminated surface must be bigger
than 0,5 m.
●The maximum ambient temperature ta= 40 °C must never be exceeded.
Installing the Beamshapers (43745/43746/43747/43748)
01) In order to install the Beamshaper, place it on the lens of the Helix. The Beamshaper is equipped with
multiple magnets which keep it firmly in position.
02) For extra safety, use a safety cable to connect the Beamshaper to the Helix.
43745 –Beamshaper for Helix M1000 Q4 Mobile (20°)
43746 –Beamshaper for Helix M1000 Q4 Mobile (40°)
43747 –Beamshaper for Helix M1000 Q4 Mobile (15°x60°)
43748 –Beamshaper for Helix M1000 Q4 Mobile 90°

15
Helix M1100 Q4 Mobile
Product code: 43750
Fig. 06
Fig. 07

16
Helix M1100 Q4 Mobile
Product code: 43750
Installing the Barndoor (43742)
01) Pull on the spring-loaded locking screws, on both sides of the barndoor (43742), to unlock the
mechanism.
Fig. 08
02) Place the barndoor on the Helix, to secure the barndoor’s screws in the Helix’s mounting holes.
Fig. 09
03) Release both locking screws to lock the barndoor in position.
04) For extra safety, use a safety cable to connect the barndoor to the Helix.
Fig. 10

17
Helix M1100 Q4 Mobile
Product code: 43750
Installing the Tophat (43741)
01) Pull on the spring-loaded locking screws, on both sides of the tophat (43741), to unlock the
mechanism.
Fig. 11
02) Place the tophat on the Helix, to secure the tophat’s screws in the Helix’s mounting holes.
Fig. 12
03) Release both locking screws to lock the tophat in position.
04) For extra safety, use a safety cable to connect the tophat to the Helix.
Fig. 13

18
Helix M1100 Q4 Mobile
Product code: 43750
Rigging
The device can be positioned on a flat surface or mounted to a truss or other rigging structure in any
orientation. Make sure that all loads are within the pre-determined limits of the supporting structure.
If the device is mounted overhead, it should always be secured with a safety cable or another
secondary suspension.
CAUTION
Restrict the access under the work area during rigging and/or derigging.
To mount the device, follow the steps below:
01) Use a clamp to attach the device to the supporting structure, as shown in Fig. 14. Make sure that the
device cannot move freely. The use of a quick lock bracket is optional.
02) Secure the device with a secondary suspension, for example a safety cable. Make sure that the
secondary suspension can hold 10 times the weight of the device. If possible, the secondary
suspension should be attached to a supporting structure independent of the primary suspension. Put
the safety cable through the safety eye, as shown in Fig. 14. You can use the safety cable supplied
with the device.
Fig. 14

19
Helix M1100 Q4 Mobile
Product code: 43750
Angle Adjustment
You can adjust the angle of the device with the 2 adjustment screws (02).
Turn the adjustment screws (02) counterclockwise to release them.
02) Tilt the device at the desired angle (see Fig. 15).
03) Turn the adjustment screws (02) clockwise to tighten them. Make sure that the device cannot move
freely after the adjustment screws (02) are tightened.
Fig. 15