TECshow iON 230B User manual

ION 230B
USER MANUAL / MANUAL DE USUARIO
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE
POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR

p. 2ION 230B
ENGLISH VERSION
Overview
Ion 230B is a beam moving head powered by an Osram Sirius®
HRI 230W lamp with a 1.3º beam angle. The unit has 14 colors
+ open, bidirectional rainbow eect, and provides 8 rotating,
interchangeable & indexable gobos + open and 3 & 8-facet
rotating prism + frost filter to enable the creation of stunning
visual designs. Last but not least - thanks to its 3 phase mo-
tor - Ion 230B is capable of extremely fast movements & it’s
optionally equipped with a Wireless Solution® card.
Specifications
Source & Optics
Light Source: Osram Sirius® HRI 230W
Lamp life: 3,000 hours
Beam angle: 1.3°
Photometric data
Luminous Flux: 10150 lumen / 57380 lux @ 20m (60 .)
Eects & Functions
Color wheel: 14 interchangeable dichroic filters + open, and
bidirectional rainbow eect
Color bounce
Rotating gobo wheel: 8 interchangeable, rotating, indexable
gobos + open
Gobo diameter: Outside 13.8 mm, Inside 6 mm
Gobo animation eects & shaking
8-facet rotating prism + frost
Motorized focus
Dimmer: Full range 0-100%
Strobe eect
Control
DMX channels: 12/14/16/19
Wireless DMX (optional)
Advanced RDM function
Hibernation when lost DMX for preset time
Indicate temperature info of base, arm and lamp
Back-up communicating IC
RDM read voltage, current, power consumption of lamp
Soware upgrade via DMX
Fan speed auto-change according to temperature
Movement
Pan: 360° / 540°
Tilt: 265°
3 phase motor
16-bit resolution
Auto repositioning
Electrical
Input voltage range: 100–240V, 50-60Hz
Power supply: Electronic auto-ranging
Power consumption: 360W
Physical
DMX connectors: 2 XLR connectors (XLR-3 In and Out)
Power supply connectors: PowerCON® In/Out
2.4 inch LCD graphic display
Dimensions: 343x319x513 mm. / 13.5x12.5x20.2 in.
Weight: 15 Kg. / 33 Lbs.

1. Product Introduction:
1.1 Before unpack the fixture, pls make sure that the packing
is in good condition, following items will be found in the box:
• The fixture
• This users guide
• 3m DMX cable
• 1.5m power cable with powercon
• Omega bracket for hanging installation
• Safety chain
1.2 Specification
Source
• Light source: Osram Sirius HRI 230W discharge lamp
• Led life: 3.000 hours
• Luminous Flux: 10150lumen, 61200lux@20m
• Control: Remote on/o via DMX
• Ballast: switching mode power supply
Optical System
• Beam angle: 1.3°
X/Y
• Pan: 360° (4.0 sec) or 540°(3.58 sec), Tilt: 265° (2.8 sec)
• 16-bit resolution
• Auto repositioning
Colors
• 14+open, interchangeable, indexable and bidirectional
rainbow eect
• New color bounce eect
Gobos
• Outside ¢13.8mm, inside ¢6mm
• 8+ open custom interchangeable position for rotat ing
gobo wheel
• Real indexable and gobo shaking
• Distinctive gobo animation eect
Features
• DMX channels: 16/19/12/14
• Color wheel: 14+1 colors
• Rotating gobo wheel: 8+1 gobos
• Motorized focus
• Full range 0-100% dimmer
• Various strobe
• Rotating Eect wheel with 3 facets,8 facets prism and
frost
• RDM function to change DMX address, display flip, X/Y
Reverse, show lamp voltage, current and power con-
sumption info.
• Soware upgrade via DMX
• Hibernation when lost DMX for preset time
• Indicate temperature info of base, arm and lamp
• Fan speed auto change according to temperature
Display
• 2.4inch super nice LCD display with friendly English/ Chi-
nese/French/Spanish menu
• Auto lock
• Flip
• Back-up communicating IC
p. 3ION 230B
ENGLISH VERSION

1.3 Description of the Device
1. Project lens
2. Head
3. Arm
4. Base
5. Display
6. Foot stand
7. Operation button
8. Handle
9. Wireless indicator
10. Mic
11. Le button
12. Battery indicator
13. Up button
14. Down button
15. Enter button
16. Right button
17. 3-pin DMX in
18. 3-pin DMX out
19. Powercon in
20. Powercon out
21. Fuse
22. Power switch
p. 4ION 230B
ENGLISH VERSION

1.4 Colors and Gobos
2Tan
3 CTB
4
Yellow
5 Shallow purple
6 Brown
7 Blue green
8 Purple red
9 Grass green
10 UV
11 Megenta
12 Green
13 Orange
14 Blue
15 Red
1 Open Open
p. 5ION 230B
ENGLISH VERSION

Static gobo wheel
2. Safety and maintenance Information
2.1 Safety Info
Before operate this unit, please carefully read this users guide and keep if
needed in future. It’s necessary to respect following rules.
The disposal of the device aer lifecycle could damage the environment, need
to take it to special company for recycling or return to authorized dealer.
The products referred to in this manual conform to the Eur opean Community
Directives and are therefore marked with CE logo.
Keep this device away from children and unauthorized users, the manufac-
turer will not take responsibility for the damage due to any disregard of the
information provided in this manual and wrong operation.
Before operate the device, pls make sure the fixture is in good housing, ensure
pan and tilt can rotate in its complete range.
p. 6ION 230B
ENGLISH VERSION

Pls make sure minimal 0.5m distance need to kept between the fixture to any
flammable material.
The device can only run with 100-240v voltage, 50/60Hz power, don’t connect
to any other wrong power. Disconnect the device from main power before
open the shield or maintenance.
The device is designed only for indoor usage, pls keep it away from moisture.
Do not expose the device under the sun or directly to any other lighting source.
Never look directly into the projecting lens when the fixture is power on, the
light may trigger epileptic seizures in photosensitive persons or persons with
epilepsy. Especially at beam eect, extreme caution and observance of these
safety instructions is mandatory.
Don’t put or install the device on a surface that subject to vibration
or bumps.
Ta=45℃ The device is supposed to work in the temperate range -15° C and +45° C, do
not use the device when the temperate exceed this range.
The lens, shield need to be replaced when obviously broken, never use the
device when the shield is not completed closed.
Safety I class device, need to be earth connected.
When the fixture is hanged overhead, the safety rope must be fixed to the
bottom of the device to the appropriate fixing point.
Always carry the device by the handles, do not take the head or arm directly
for transportation.

--0.5m
2.2 Maintenance
2.2.1 Operation only allowed to qualified person, damages
due to unprofessional operation or remove of any parts in-
side will not be considered in warranty service. There are no
serviceable parts inside the device or package, service only
leaves to authorized dealers.
2.2.3 Never allow the optical components contact with oil,
fat or any other liquid.
2.2.4 A regular clearance of the device is needed for long-
term usage, this is very helpful to maintain the lifetime and
brightness need to use a so and lint-free cloth to clean the
optical system, fan and air flowing tunnel.
p. 7ION 230B
ENGLISH VERSION

2.2.5. Trouble Shooting
2.2.6 Replacement of the fuse
Need to replace with same type and rating, which originally
installed in the device.
Step One: Unplug power cable from main power.
Step Two: Unscrew the fuse holder out of the housing with a
screwdriver.
Step Three: Remove the broken fuse and replace with an ex-
act same type of new fuse.
Step Four: Insert the fuse holder back to the housing and
screw tight and reconnect power.
Problems Possible reasons Checking or solutions
Device not power up Powercon or power cable damaged Change a good power cable to try
Faulty power supply Replace new power supply
Pan/Tilt error or vibrate
Faulty Pan/Tilt PCB Replace PT001 PCB
Faulty opto sensor Replace opto sensor OP001
Cable loosen Check the cable connect to OP001
LED o
Temperature protection Check the temperature from menu
Fan not working Check the fan speed info from menu
Faulty LED Replace new LED
Dimmer and strobe set at 0 Set dimmer and strobe channel at 255
Faulty power supply Replace new power supply
Device not response to DMX
Faulty communication IC Replace the IC with back-up one in the display PCB
Faulty display PCB Replace new display PCB
Wrong DMX addressing Check the address and setting
Faulty DMX cable Change to a good DMX cable
3. Installation
3.1 The device could be either put on a solid and even Sur-
face, or mounted upside down or sideways like le picture.
3.2 The mounting place must be suicient stable and be able
to support a weight of 10 times of the unit’s weight. When the
fixture is hanged, always additionally secure the device with
the safety chain, fasten the safety rope at a suitable position
so that the maximum fall of the projector will be 20 cm
p. 8ION 230B
ENGLISH VERSION

How to do mounting installation.
Step three: Install the whole device onto appropri-
ate truss and fasten the clamps, tight the safety rope
with the truss or other fixing point at a suitable posi-
tion that drop down distance not exceed 20 cm.
Step two: Install the clamp and bracket on the bot-
tom of panel, fasten the quick-locks;
Step one: Installation the clamp onto the bracket;
4.1 Meaning of the icon in menu
CONNECT LIGHT INFOMATION SET PROGRAM
p. 9ION 230B
ENGLISH VERSION

4.2 Menu tree
Default setting shadowed. Mark with 1. can be basic reload-
ed, 2. be program reloaded, 3. can be private reloaded.
Connect
DMX Address①XXX DMX address seng
Light
Turn On/O ON/OFF Turn On the lamp
Automac ON/OFF Lamp On/o when power on
DMX Control ON/OFF DMX control or not
Max Temperature①80~139℃,125℃/176~282℉, 257℉
Lamp o if temperature
connuously over for 5
minutes
Lamp Adjust①PAN…… Adjust value of channel
Informaon
Time Info.
Current XXXX(Hours) Fixture boot me
Fixture Life XXXX(Hours) Fixture total run me
Lamp Life XXXX(Hours) Lamp total run me
Lamp Info.
Voltage
HID Lamp InformaonCurrent
Power
Temperature Near Lamp Temp (depends on xture) Temperature Sensors
Fans Speed Near Lamp Fan (depends on xture) Fan speed Sensors
Channel Value PAN…… Display value of channel
Error Message Pan,Tilt…… Error channels
Fixture Model xxxxxxxxxxxx Display model brand and
model
Soware Ver 1U01 V1.0.00…………. Version of each IC
p. 10ION 230B
ENGLISH VERSION