Show Tec Wipe Out 3W User manual

Wipe Out 3W V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 42567
MANUAL
ENGLISH

1
Ordercode: 42567
Wipe Out 3W
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Rigging ............................................................................................................................................................................4
Connection with the mains.........................................................................................................................................5
Return Procedure..........................................................................................................................................................5
Claims..............................................................................................................................................................................5
Description of the device.................................................................................................................................................6
Overview ........................................................................................................................................................................7
Installation...........................................................................................................................................................................8
Set Up and Operation .......................................................................................................................................................8
Control Modes...............................................................................................................................................................8
One Wipe Out (Auto, Built-in programs and Sound-controlled) ......................................................................8
Multiple Wipe Outs (Master/Slave control)...........................................................................................................8
Multiple Wipe Outs (DMX Control)..........................................................................................................................9
Fixture Linking...............................................................................................................................................................10
Data Cabling...............................................................................................................................................................10
Control Panel ...............................................................................................................................................................11
Control Mode ..............................................................................................................................................................11
DMX Addressing ..........................................................................................................................................................11
Menu Overview...........................................................................................................................................................12
Main Menu Options.................................................................................................................................................13
1. Auto Run Mode....................................................................................................................................................13
1.1 LED Menu ............................................................................................................................................................13
1.2. Bar Menu ............................................................................................................................................................14
2. Built-in Programs...................................................................................................................................................15
3. Sound-controlled Mode .....................................................................................................................................15
4. DMX-512 Mode ....................................................................................................................................................15
5. Master/Slave Mode.............................................................................................................................................15
6. Settings...................................................................................................................................................................16
DMX Channels .............................................................................................................................................................17
1 Channel..................................................................................................................................................................17
12 Channels ..............................................................................................................................................................18
16 Channels ..............................................................................................................................................................19
Maintenance....................................................................................................................................................................20
Replacing the Fuse.....................................................................................................................................................20
Troubleshooting ...............................................................................................................................................................21
No Light.........................................................................................................................................................................21
No Response to DMX..................................................................................................................................................21
Product Specification .....................................................................................................................................................23
Dimensions........................................................................................................................................................................24
Notes ..................................................................................................................................................................................25

2
Ordercode: 42567
Wipe Out 3W
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
●Showtec Wipe Out 3W
●IEC power cable (1,5m)
●4 x quick locks + 2 x mounting brackets
●User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving your lifespan expectancy is of a higher priority, place care in providing
for lower operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
●be qualified
●follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.

3
Ordercode: 42567
Wipe Out 3W
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoor, avoid contact with water or other liquids.
Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
If the lens is obviously damaged, it has to be replaced, so that its functions are not impaired due to
cracks or deep scratches.
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of the reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the Wipe Out 3W. The manufacturer
will not accept liability for damages caused by the misuse or incorrect installation of this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
During the initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective.
Repairs, servicing and electric connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.

4
Ordercode: 42567
Wipe Out 3W
Operating Determinations
●This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
●The minimum distance between light-output and the illuminated surface must be more than 1 meter.
●The maximum ambient temperature ta = 40°C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
●If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
●Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
●If the projector is lowered from the ceiling or high joists, professional trussing systems have to be used.
●Use a clamp to mount the projector, with the mounting-bracket, to the trussing system.
●The projector must never be fixed swinging freely in the room.
●The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety-cable.
●When rigging, derigging or servicing the projector, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.
The Wipe Out 3W can be placed on a flat stage floor or mounted to any kind of truss with a clamp.
Improper installation can cause serious damage to people and property !

5
Ordercode: 42567
Wipe Out 3W
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
FASE
N
BLUE
BLACK
SILVER
NULL
YELLOW/GREEN
GREEN
GREEN
EARTH
Make sure that the device is always connected properly to the earth!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

6
Ordercode: 42567
Wipe Out 3W
Description of the device
Features
The Showtec Wipe Out 3W is a compact and powerful fixture for both indoor and outdoor use.
●Input Voltage: 100-240 VAC, 60/50Hz
●Power consumption: 50W
●LED Quantity: 8 x 3W Cool White High Power LED, Cool White 4200K
●Light output @2 meter: 5300lux
●DMX channels: 1, 12 or 16 Channels
●IP20 Rating
●Specially designed housing ensures an optimum heat dissipation during operation
●Connections: 3-pin DMX IN & OUT connector & IEC to Schuko power cable
●DMX-control via standard DMX-controller
●On Board: LCD display for easy setup
●Control modes: Auto, Built-in programs, Sound-controlled, DMX-512, Master/Slave
●Divided in 2 sections and equipped with very fast motors to create amazing moving beam effects
●Beam Angle: 2,5°
●Dimmer: 0-100%
●Strobe: 0-20Hz
●Housing: black-painted metal and ABS plastic
●Cooling: Convection (no fans)
●Fuse: T2AL/250V
●Dimensions: 1065 x 85 x 145 mm (LxWxH)
●Weight: 8,6 kg
The Wipe Out is available in 3 different models which distinguish in LED power and color.
42567 Wipe Out 8 x 3W High Power LED, Cool White 4200K
42568 Wipe Out 8 x 9W High Power LED Cool White 4200K
42569 Wipe Out 8x 8 Watt RGBW High Power LEDs

7
Ordercode: 42567
Wipe Out 3W
Overview
Fig. 01
01) 8 x 3W Cool White High Power LED
02) 3-pin DMX signal connector IN
03) IEC power connector 100-240V IN + Fuse T2AL/250V
04) Ground/earth connection
05) Power switch ON/OFF
06) LCD display + menu buttons
07) IEC power connector 100-240V OUT
08) 3-pin DMX signal connector OUT
NOTE: Knowledge of DMX is required to fully utilize this unit.

8
Ordercode: 42567
Wipe Out 3W
Installation
Remove all packing materials from the Wipe Out 3W. Check that all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Control Modes
There are 5 modes:
Auto
Built-in programs
Sound-controlled
DMX-512 (1CH, 12CH, 16CH)
Master/Slave
One Wipe Out (Auto, Built-in programs and Sound-controlled)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Wipe Out is not connected with a DMX cable, it functions as a stand-alone device.
05) Please see pages 13-15 for more information about the Auto, Built-in programs and Sound-controlled
modes.
Multiple Wipe Outs (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Wipe Out.
The pins:
01) Earth
02) Signal (-)
03) Signal (+)
05) Link the units as shown in Fig. 02, Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units. You can
use the same functions on the master device as described on pages 13-15 (Auto, Built-in or Sound-
controlled). This means that you can set your desired operation mode on the master device and all
slave devices will react the same as the master device.
Multiple Wipe Outs (Master/Slave control)
Fig. 02

9
Ordercode: 42567
Wipe Out 3W
Multiple Wipe Outs (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Wipe Outs and other devices.
05) Link the units as shown in Fig. 03. Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
06) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
Multiple Wipe Outs DMX Set Up
Fig. 03
Note : Link all cables before connecting electric power

10
Ordercode: 42567
Wipe Out 3W
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of Wipe Outs on a DMX data link: 30 fixtures
Maximum recommended number of Wipe Outs on a power link: 8 fixtures @110V
Maximum recommended number of Wipe Outs on a power link: 16 fixtures @240V
Data Cabling
To link fixtures together you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
•DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin.
Ordercode FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
•DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
•DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).

11
Ordercode: 42567
Wipe Out 3W
The Wipe Out can be operated with a controller in control mode or without the controller in stand-alone
mode.
Control Panel
A)
B)
C)
D)
E)
LCD Display
MODE button
SETUP Button
UP Button
DOWN Button
Fig. 04
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller.
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the
first channel from which the Wipe Out will respond to the controller.
Please note when you use the controller, the unit has 16 channels.
When using multiple Wipe Outs, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Wipe Out should be 1(001); the DMX address of the second Wipe
Out should be 1+16=17 (017); the DMX address of the third Wipe Out should be 17+16=33 (033), etc.
Please, be sure that you do not have any overlapping channels in order to control each Wipe Out
correctly.
If two or more Wipe Outs are addressed similarly, they will work similarly.
Controlling:
After having addressed all Wipe Out fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the Wipe Out will automatically detect whether DMX 512 data is received or
not. If there is no data received at the DMX-input, the problem may be:
•The XLR cable from the controller is not connected to the input of the Wipe Out.
•The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 30 seconds
When no button is pressed for 30 seconds, the display will turn off.
To light up the display, you have to press the MODE, SETUP, UP or DOWN button.
Once you have pressed the button, the display will light up.

12
Ordercode: 42567
Wipe Out 3W
Menu Overview

13
Ordercode: 42567
Wipe Out 3W
Main Menu Options
Auto Run Mode
Built-in programs
Sound-controlled Mode
DMX-512 Mode
Master/Slave Mode
Settings
1. Auto Run Mode
With this menu you can set Auto Run mode of the Wipe Out.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the UP/DOWN buttons to choose one of the 2 options:
LED Menu
BAR Menu
04) Press the SETUP button to enter the desired menu.
1.1 LED Menu
01) Press the UP/DOWN buttons to choose one of the following 2 options:
Auto Program
Manual Program
02) When the display shows , press the SETUP button to open the menu.
03) Press the UP/DOWN buttons to choose one of the following 2 options:
LED Speed
LED flash frequency

14
Ordercode: 42567
Wipe Out 3W
04) Press the SETUP button to enter the desired menu.
05) When the display shows , press the SETUP button to enter the LED speed settings.
06) Press the UP/DOWN buttons to increase/decrease the LED speed. The adjustment range is between
, from slow to fast.
07) When the display shows , press the SETUP button to enter the flash frequency settings.
08) Press the UP/DOWN buttons to increase/decrease the flash frequency. The adjustment range is
between , from low to high frequency.
09) Press the MODE button until you return to step 3 and press the UP/DOWN buttons until the display
shows .
10) Press the SETUP button to open the manual settings.
11) Press the UP/DOWN buttons to choose one of the 2 options:
LED brightness
LED flash frequency
12) When the display shows , press the SETUP button to enter the LED brightness settings.
13) Press the UP/DOWN buttons to increase/decrease the brightness. The adjustment range is between
, from dark to brightest.
14) When the display shows , press the SETUP button to enter the flash frequency settings.
15) Press the UP/DOWN buttons to increase/decrease the flash frequency. The adjustment range is
between , from low to high frequency.
1.2. Bar Menu
01) Press the MODE button until you return to page 13, 1. Auto Run Mode, step 03).
02) Press the UP/DOWN buttons until the display shows .
03) Press the SETUP button to enter the BAR Menu.
04) Press the UP/DOWN buttons to choose one of the 2 following options:
Automatic BAR movement
Manual BAR movement
05) When the display shows , press the SETUP button to enter the automatic BAR movement
speed settings.
06) Press the UP/DOWN buttons to increase/decrease the movement speed. The adjustment range is
between , from slow to fast.
07) When the display shows , press the SETUP button to enter the manual motor movement
settings.
08) Press the UP/DOWN buttons to choose one of the 2 following options:
Left motor settings
Right motor settings
09) When the display shows , press the SETUP button to enter the left motor settings.
10) Press the UP/DOWN buttons to adjust the position of the left motor. The adjustment range is between
.
11) When the display shows , press the SETUP button to enter the right motor settings.

15
Ordercode: 42567
Wipe Out 3W
12) Press the UP/DOWN buttons to adjust the position of the right motor. The adjustment range is
between .
2. Built-in Programs
With this menu you can you can set the built-in programs.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the UP/DOWN button to toggle between the 10 built-in programs: .
3. Sound-controlled Mode
With this menu you can you can set the sound sensitivity.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the UP/DOWN buttons to set the sound sensitivity. The adjustment range is between
, from low to high sensitivity.
04) Turn the music on and the Wipe Out 3W will react to the beat of the music.
4. DMX-512 Mode
With this menu you can set the DMX address.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the UP/DOWN buttons to choose one of the following 2 options:
DMX address settings
Channel mode settings
04) When the display shows , press the SETUP button to enter the DMX address settings.
05) Press the UP/DOWN buttons to set the desired DMX address between .
06) When the display shows , press the SETUP button to enter the channel mode settings.
07) Press the UP/DOWN buttons to toggle between the following 3 channel modes:
1-channel mode
12-channel mode
16-channel mode
5. Master/Slave Mode
With this menu you can set the device as a master or a slave device.
01) Press the MODE button until the display shows .
02) If the device has not been set to slave, it is automatically classified as a master device. All slave
devices will follow the movement of the master device.
03) If the device has been set to slave, it will react the same as the master device.

16
Ordercode: 42567
Wipe Out 3W
6. Settings
With this menu you can manually adjust the device’s settings.
01) Press the MODE button until the display shows .
02) Press the SETUP button to open the menu.
03) Press the UP/DOWN buttons to toggle between the following 6 options:
Set the amount of time after which the display turns off
Set the value of the motor correction
Restore to factory default settings
Not functional at the moment
Device’s voltage
Product specification
04) When the display shows , press the SETUP button to open the menu.
05) Press the UP/DOWN buttons to set the time after which the display turns off. There are 5 options to
choose from: 5s, 10s, 20s, 30s and On (the display remains continuously in ON position).
06) When the display shows , press the SETUP button to open the menu.
07) Press the UP/DOWN buttons to choose one of the 2 motors:
Left motor
Right motor
08) Press the SETUP button to enter one of the 2 menus.
09) Press the UP/DOWN buttons to change the value of the motor correction. The adjustment range for
the left motor is between and for the right motor
.

17
Ordercode: 42567
Wipe Out 3W
10) Once you have set the desired value and confirmed it, your device will remain tilted. When you want
to return to the basic horizontal setting, please reset your Wipe Out and return to its factory default
settings.
11) When the display shows , press the SETUP button to enter the menu.
12) When the display shows , press the SETUP button to restore the default settings. Otherwise,
press the MODE button to return to the previous menu, without resetting the device.
13) When the display shows . Press the SETUP button to see the device’s voltage.
14) When the display shows , press the SETUP button to enter the product specification menu.
15) Press the UP/DOWN buttons to toggle between the following pieces of information:
Current model number
Last successful update
Driver version
Software version
DMX Channels
1 Channel
Channel 1 –Functions
0-19
LED closed, Wipe Out returns to the default horizontal position
20-29
Program 1
30-39
Program 2
40-49
Program 3
50-59
Program 4
60-69
Program 5
70-79
Program 6
80-89
Program 7
90-99
Program 8
100-109
Program 9
110-119
Program 10
120-139
LED closed, Wipe Out returns to the default horizontal position
140-255
Sound-controlled Mode, from low to high sound sensitivity

18
Ordercode: 42567
Wipe Out 3W
12 Channels
Channel 1 –Left Bar Tilt movement
0-180
Gradual tilt movement, from 0-180°
181-255
Not functional
Channel 2 –Left Bar Tilt movement speed
0-255
Gradual speed adjustment, from slow to fast
Channel 3 –Right Bar Tilt movement
0-180
Gradual tilt movement, from 0-180°
181-255
Not functional
Channel 4 –Right Bar Tilt movement speed
0-255
Gradual speed adjustment, from slow to fast
Channel 5 –Dimmer intensity LED1
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 6 –Dimmer intensity LED2
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 7 –Dimmer intensity LED3
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 8 –Dimmer intensity LED4
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 9 –Dimmer intensity LED5
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 10 –Dimmer intensity LED6
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 11 –Dimmer intensity LED7
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 12 –Dimmer intensity LED8
0-255
Gradual adjustment from dark to brightest, 0-100%

19
Ordercode: 42567
Wipe Out 3W
16 Channels
Channel 1 –Left Bar Tilt movement
0-180
Gradual tilt movement, from 0-180°
181-255
Not functional
Channel 2 –Left Bar Tilt movement speed
0-255
Gradual speed adjustment, from slow to fast
Channel 3 –Right Bar Tilt movement
0-180
Gradual tilt movement, from 0-180°
181-255
Not functional
Channel 4 –Right Bar Tilt movement speed
0-255
Gradual speed adjustment, from slow to fast
Channel 5 –Dimmer intensity LED1 CH13 must be open
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 6 –Dimmer intensity LED2 CH13 must be open
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 7 –Dimmer intensity LED3 CH13 must be open
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 8 –Dimmer intensity LED4 CH13 must be open
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 9 –Dimmer intensity LED5 CH13 must be open
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 10 –Dimmer intensity LED6 CH13 must be open
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 11 –Dimmer intensity LED7 CH13 must be open
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 12 –Dimmer intensity LED8 CH13 must be open
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 13 –Master dimmer
0-255
Gradual adjustment from dark to brightest, 0-100%
Channel 14 –Functions
0-9
Not functional
10-19
Auto Run Mode
20-29
Program 1
30-39
Program 2
40-49
Program 3
50-59
Program 4
60-69
Program 5
70-79
Program 6
80-89
Program 7