Show Tec Helix 4000 Q4 15 V1 User manual

Helix 4000 Q4 15° V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 43720
MANUAL
ENGLISH

1
Ordercode: 43720
Helix 4000 Q4 15°
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................3
Operating Determinations ..........................................................................................................................................5
Rigging ............................................................................................................................................................................5
Connection with the mains.........................................................................................................................................7
Return Procedure..........................................................................................................................................................7
Claims..............................................................................................................................................................................7
Description of the device.................................................................................................................................................8
Features ..........................................................................................................................................................................8
Optional accessories....................................................................................................................................................8
Frontside..........................................................................................................................................................................9
Backside .........................................................................................................................................................................9
Installation.........................................................................................................................................................................10
Set Up and Operation .....................................................................................................................................................10
Control Modes.............................................................................................................................................................10
One Helix 4000 Q4 (Auto Run Program + Built-in Programs)............................................................................10
One Helix 4000 Q4 (Manual Mode) .....................................................................................................................10
Multiple Helix 4000 Q4s (Master / Slave Control) ...............................................................................................10
Multiple Helix 4000 Q4s (DMX Control).................................................................................................................11
Wireless DMX Control ..............................................................................................................................................12
Fixture Linking...............................................................................................................................................................15
Data Cabling...............................................................................................................................................................15
Control Panel ...............................................................................................................................................................16
DMX Control Mode.....................................................................................................................................................16
DMX Addressing ..........................................................................................................................................................16
Menu Overview...........................................................................................................................................................17
Main Menu Options....................................................................................................................................................19
1 DMX Control ..........................................................................................................................................................19
1.1 DMX Address ......................................................................................................................................................19
1.2 DMX Channels....................................................................................................................................................19
1.3 W-DMX .................................................................................................................................................................19
2 Slave Mode............................................................................................................................................................20
3 Auto Run Program ................................................................................................................................................20
4 Manual Mode (Dimmer) .....................................................................................................................................20
5 Built-in Programs (Program) ................................................................................................................................20
6 Settings....................................................................................................................................................................22
6.1 Curves settings ...................................................................................................................................................22
6.2 LCD Backlight .....................................................................................................................................................23
6.3 LCD Backlight Dimmer......................................................................................................................................23
6.4 Factory Reset......................................................................................................................................................23
6.5 DMX Fail...............................................................................................................................................................23
7 Information.............................................................................................................................................................23
DMX Channels .............................................................................................................................................................24
4 Channels ................................................................................................................................................................24
6 Channels ................................................................................................................................................................24
8 Channels ................................................................................................................................................................24
Maintenance....................................................................................................................................................................27
Troubleshooting ...............................................................................................................................................................27
No Light.........................................................................................................................................................................27
No Response to DMX..................................................................................................................................................27
Product Specification .....................................................................................................................................................29
Dimensions........................................................................................................................................................................30

2
Ordercode: 43720
Helix 4000 Q4 15°
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
●Showtec Helix 4000 Q4 with IP54 rating DMX
IN/ DMX OUT cables (0,35m)
●Schuko to Neutrik PowerCON True1
(cable length 1,5 m)
●2 Quick-locks
●Mounting bracket
●User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving your lifespan expectancy is of a higher priority, place care in providing
for lower operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.

3
Ordercode: 43720
Helix 4000 Q4 15°
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
●be qualified
●follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
Never let the power-cord come into contact with other cables! Handle the power-cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never place any material over the lens.
Never look directly into the light source.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoor, avoid contact with water or other liquids.
Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always allow free air space of at least 50 cm around the unit for ventilation.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power-cord by the plug. Never pull out the plug by tugging the power-cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power-cord is never crimped or damaged. Check the device and the power-
cord from time to time.
If the lens is obviously damaged, it has to be replaced. So that its functions are not impaired, due to
cracks or deep scratches.

4
Ordercode: 43720
Helix 4000 Q4 15°
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of the reach of children. Never leave the unit running
unattended.
Never attempt to bypass the thermostatic switch or fuses.
For replacement use fuses of same type and rating only.
The user is responsible for correct positioning and operating of the Helix 4000 Q4. The manufacturer
will not accept liability for damages caused by the misuse or incorrect installation of this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
Repairs, servicing and electric connection must be carried out by a qualified technician.
WARRANTY: Till one year after date of purchase.

5
Ordercode: 43720
Helix 4000 Q4 15°
Operating Determinations
●This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
●The minimum distance between light-output and the illuminated surface must be more than 1 meter.
●The maximum ambient temperature ta = 40°C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
●If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
●Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
●If the Helix 4000 Q4 is lowered from the ceiling or high joists, professional trussing systems have to be
used.
●Use a clamp to mount the Helix 4000 Q4, with the mounting-bracket, to the trussing system.
●The Helix 4000 Q4 must never be fixed swinging freely in the room.
●The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety-cable.
●When rigging, derigging or servicing the Helix 4000 Q4, always make sure, that the area below the
installation place is blocked and staying in the area is forbidden.

6
Ordercode: 43720
Helix 4000 Q4 15°
The Helix 4000 Q4 can be placed on a flat stage floor or mounted to any kind of truss by a clamp.
Improper installation can cause serious damage to people and property!

7
Ordercode: 43720
Helix 4000 Q4 15°
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

8
Ordercode: 43720
Helix 4000 Q4 15°
Description of the device
Features
The Showtec Helix 4000 Q4 is a High-power panel light with IP54 protection grade. It has an extreme high
light output and is very suitable for illumination of larger areas indoor as well (temporarily) outdoor.
LED Quantity: 40 x RGBW 4-in-1 10W LEDs
Refreshrate: 3.0 KHz
DMX Modes: 4, 6, 8 Channels
Beam angle: 15°
Colormixing: RGBW
Colour range: 16,7 million additive colors
IP Rating: IP54
Wireless DMX (Wireless Solutions) is standard
Quick-locks for fast rigging and mounting
Housing: Specially designed housing ensures an optimum heat dissipation during operation.
Input Voltage: 100-240 VAC, 50/60Hz
Power consumption: 390W max @FO (full output)
DMX-control via standard DMX-controller
On Board: LCD display for easy Set Up
Control mode: Auto Run Program, Built-in Programs, Master / Slave, DMX512, Manual Mode, W-DMX
Dimmer: 0-100%
Strobe: 0-20Hz
Housing: Die Cast Aluminium Powder Coat Finish
Power connectors: Neutrik PowerCON True1
Data connectors: 3-pin XLR-HD male, 3-pin XLR-HD female
Cooling: Forced-air
Working temperature: -10°C ~40°C
Lumen @2m: Red: 5780 Lux@2m
Green: 13820 Lux@2m
Blue: 2271 Lux@2m
White: 18040 Lux@2m
Full On: 35680 Lux@2m
Dimensions: 532 x 220 x 315 mm (LxWxH)
Weight: 11,4 kg
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
90475 Powercable 0,5 m Neutrik Powercon True1 M/F
90476 Powercable 1,5 m Neutrik Powercon True1 M/F
90477 Powercable 3,0 m Neutrik Powercon True1 M/F
90478 Powercable 5,0 m Neutrik Powercon True1 M/F
D7247 Case for 4x Helix 4000 Q4
FL73150 1,5 m IP65 XLR/M 3p. > XLR/F 3p. Neutrik
FL733 3,0 m IP65 XLR/M 3p. > XLR/F 3p. Neutrik
FL736 6,0 m IP65 XLR/M 3p. > XLR/F 3p. Neutrik
FL7310 10 m IP65 XLR/M 3p. > XLR/F 3p. Neutrik
50726 LED operator 4 Air
50231 W-DMX Micro Transceiver

9
Ordercode: 43720
Helix 4000 Q4 15°
Frontside
Fig.01
01) Antenna for wireless DMX
02) 40 x RGBW 4-in-1 10W LEDs
03) Angle Adjustment screw
Backside
Fig. 02
04) PowerCON True 1 power in
05) PowerCON True 2 power out
06) LCD Display
07) Control panel buttons
08) DMX signal connector (IN) 3-pin XLR-HD male
09) DMX signal connector (OUT) 3-pin XLR-HD female

10
Ordercode: 43720
Helix 4000 Q4 15°
Installation
Remove all packing materials from the Helix 4000 Q4. Check that all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Control Modes
There are 6 modes:
Auto Run Program
Built-in Programs
Manual Mode
Master / Slave
DMX512 (4CH, 6CH or 8CH)
Wireless DMX control
One Helix 4000 Q4 (Auto Run Program + Built-in Programs)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Helix 4000 Q4 is not connected by a DMX-cable, it functions as a stand-alone device.
05) Please see page 20 and 21 for more information.
One Helix 4000 Q4 (Manual Mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Helix 4000 Q4 is not connected by a DMX-cable, it functions as a stand-alone device.
05) Please see page 20 for more information about the manual mode functions.
Multiple Helix 4000 Q4s (Master / Slave Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Helix 4000 Q4s.
The pins:
01) Earth
02) Signal (-)
03) Signal (+)
05) Link the units as shown in (Fig.03) on page 11. Connect a DMX signal cable from the first unit's DMX
"out" socket to the second unit's "in" socket. Repeat this process to link the second and third units. You
can use the same functions on the master device as described on page 20 and 21. This means on
the master device you can set your desired operation Mode and all slave devices will react the
same as the master device.

11
Ordercode: 43720
Helix 4000 Q4 15°
Multiple Helix 4000 Q4s (Master / Slave Set Up)
Fig. 03
Multiple Helix 4000 Q4s (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Helix 4000 Q4 and other devices.
05) Link the units as shown in (Fig.04), Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second and third units.
06) Supply electric power: Plug electric mains power cords into each unit's PowerCON socket, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.

12
Ordercode: 43720
Helix 4000 Q4 15°
Multiple Helix 4000 Q4s (DMX Set Up)
Fig. 04
Note: Link all cables before connecting electric power!
Wireless DMX Control
You can use the Helix 4000 Q4 in a wireless DMX setup. Make sure the device is in its Wireless DMX mode,
which can be set in the main menu, see page 19 for more information.
Sweden 2.4GHz Wireless communication module
Communication distance:
depending on the transmitting power or transmitter module
Test conditions:
W-DMX TRx Transmitter module, 2dBi Antenna, transmitting power
20dBm (100mW)
Range indoor:
60m (approx. through three concrete walls)
Range outdoor:
250m
Wireless DMX connection
The wireless receiving module “Pico G4 Receiver, 2.4GHz”, provided by Swedish WIRELESS SOLUTION, only
has a 2.4 GHz wireless signal receiving function. In order to match the wireless signal, please use the
Wireless DMX Micro Transmitter/ Black Box F-1 G4 MK2 by WIRELESS SOLUTION (50231).
To control the status of the wireless communication, please look at the green LED indicator light on the
left side of the display.
Wi-fi Problems:
01) No emitter/sender matching.
The LED Indicator dims for a long period of time.
02) Matching signal with one emitter, but loss of signal communication.
The LED Indicator light will light up for 100ms and then dim for 100ms; The LED will flicker quickly.
03) Communication with an emitter, but no DMX data.
The LED Indicator will light up for 900ms and then dim for 100ms; The LED will flicker slowly.
When the wireless DMX communication is normal, the LED indicator will always be on.
The Helix 4000 Q4 cannot receive a wireless DMX signal and a DMX cable
signal at the same time
When the device is in auto-run mode or built-in program mode, please ensure that the matching 2.4GHz
wireless signal transmitter is OFF.

13
Ordercode: 43720
Helix 4000 Q4 15°
The Helix 4000 Q4 is only a WDMX receiver and never a WDMX sender
Fig. 05
Example (Fig. 05):
In AutoRun Mode and Program Mode, the Helix 4000 Q4 cannot send a signal to another Helix 4000 Q4
wirelessly !!
In one of these modes, the slave Helix 4000 Q4 fixtures must always be connected via a DMX signal
cable.
When the Helix 4000 Q4 operates in DMX or SLAVE mode, the Helix 4000 Q4 can receive a Wireless DMX
signal (CH1-512) and at the same time it can also send out a DMX signal through a DMX cable.

14
Ordercode: 43720
Helix 4000 Q4 15°
The Helix 4000 Q4 is only a WDMX receiver and never a WDMX sender
Fig. 06
Example (Fig. 06):
The Showtec Operator Air (50726) sends out a wireless signal with 512 channels and the Helix 4000 Q4
WDMX picks up this signal. It uses the first 4 channels for its own setup and sends the rest of the channels
through a DMX cable to the other Compact Pars 7 (42580).

15
Ordercode: 43720
Helix 4000 Q4 15°
Connect the Helix 4000 Q4 to the Wireless DMX signal transmitter
The Helix 40000 Q4 cannot actively match a random wireless signal transmitter.
In order to create a Wireless match, please check the manual of your wireless signal transmitter.
We advise you to use the Wireless DMX Micro Transmitter/ Black Box F-1 G4 MK2 by WIRELESS SOLUTION
(Fig. 07).
Ordercode 50231
Fig. 07
Disconnect from the Wireless DMX signal transmitter
The Helix 4000 Q4 can be disconnected from the wireless DMX signal transmitter.
You can turn off the W-DMX in the main menu, see page 19 for more information.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master / slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of Helix 4000 Q4s on a DMX data link: 30 fixtures
Maximum recommended number of Helix 4000 Q4s on a Power link: 3 fixtures @110V
Maximum recommended number of Helix 4000 Q4s on a Power link: 8 fixtures @240V
Data Cabling
To link fixtures together you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
•DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin.
Ordercode FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
•DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
•DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
•DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30.
Note: connect the Helix 4000 Q4s with the dedicated special XLR cables for outdoor use.
FL73150 1,5 m IP65 XLR/M 3p. > XLR/F 3p. Neutrik
FL733 3,0 m IP65 XLR/M 3p. > XLR/F 3p. Neutrik
FL736 6,0 m IP65 XLR/M 3p. > XLR/F 3p. Neutrik
FL7310 10 m IP65 XLR/M 3p. > XLR/F 3p. Neutrik

16
Ordercode: 43720
Helix 4000 Q4 15°
Control Panel
A. LCD Display
B. Mode button
C. Down Button
D. Up Button
E. Setup Button
Fig. 06
DMX Control Mode
The fixtures are individually addressed on a data-link and connected to the controller. The fixtures
respond to the DMX signal from the controller. (When you select the DMX address and save it, the
controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the back side of the device allows you to assign the DMX fixture address, which is
the first channel from which the Helix 4000 Q4 will respond to the controller.
Please note when you use the controller, the unit has 8channels.
When using multiple Helix 4000 Q4s make sure you set the DMX addresses right.
Therefore, the DMX address of the first Helix 4000 Q4 should be 1(001); the DMX address of the second
Helix 4000 Q4 should be 1+8=9 (009); the DMX address of the third Helix 4000 Q4 should be 9+8=17 (017),
etc. Please, be sure that you don’t have any overlapping channels in order to control each Helix 4000 Q4
correctly. If two or more Helix 4000 Q4s are addressed similarly, they will work similarly.
Controlling:
After having addressed all Helix 4000 Q4 fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the Helix 4000 Q4 will automatically detect whether DMX 512 data is received or
not. The problem may be:
The XLR cable from the controller is not connected with the input of the Helix 4000 Q4.
The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It’s necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.

17
Ordercode: 43720
Helix 4000 Q4 15°
Menu Overview

18
Ordercode: 43720
Helix 4000 Q4 15°

19
Ordercode: 43720
Helix 4000 Q4 15°
Main Menu Options
DMX Control
Master / Slave Mode
Auto Run Program
Manual Mode
Built-in Programs
Settings
Information
1 DMX Control
With this menu you can set the DMX address, choose a DMX Mode and activate the wireless DMX.
01) Use the Up / Down buttons on the device, until the display shows .
02) Press the Setup button to go to the DMX control menu, the display will show .
1.1 DMX Address
01) Press the Setup button to open the menu .
02) You can choose 512 different DMX addresses. Use the Up / Down buttons to select the required
address from .
03) Press the Mode or Setup button to go back to the previous step.
1.2 DMX Channels
01) Use the Up / Down buttons to choose the DMX Mode, the display will show .
02) Press the Setup button to enter the menu and choose between 3 DMX Modes. Use the Up / Down
buttons to select 4, 6 or 8 channels ( ).
03) Press the Mode or Setup button to go back to the previous step.
1.3 W-DMX
01) Use the Up / Down buttons until the display will show .
02) Press the Setup button to enter the W-DMX mode and choose one of 2 options with the Up / Down
buttons, the display will show .
03) Press the Mode button twice to go back to the main menu.