showtech FUSION QXV User manual

Outdoor-rated RGBW LED batten
and 15 x 1 pixel mappable matrix
www.showtech.com.au

2
SAFETY
General instruction
• The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make
risk an electric shock.
•
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
• This unit is not for home use, only professional applications.
- in places subject to vibrations or bumps;
- in places with a temperature of over 40 °C.
an inspection or contact the manufacturer directly.
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
• Always additionally secure the projector with the safety rope. When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
• The lamp (LED) shall be changed if it has become damaged or thermally deformed.
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
• Do not touch the product’s housing when operating because it may be very hot.
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
19
3.16 W-DMX WIRELESSSETTING
The FUSIONBAR QXV IP features an onboard W-DMX receiver. By default, W-DMX is OFF. To activate:
• Press the MENU button until the display shows Wireless Setting , then press ENTER.
• Press the UP/DOWN buttons to select Receive On , then press ENTER.
• To reset the onboard W-DMX receiver, select Receive Reset , then press ENTER.
3.17 FACTORY RESET
The FUSIONBAR QXV provides a factory reset function to restore all default values:
• Press the MENU button until the display shows Reset Factory , then press ENTER.
• Press the UP/DOWN buttons to select Yes , then press ENTER.
3.18 PHOTOMETRICS
Beam Angle: 16°
Full
42935 lux 4771 lux 1717 lux
1m 3m 5m

3
Packing content FUSIONBAR QXV
• Mounting bracket (2 pcs.)
• Power cable
• User manual
TABLE OF CONTENTS Safety
General instructions
Warnings and installation precautions
General information
1 Introduction
1. 3 Operating elements and connections
2 Installation
2. 1 Mounting
2.2 Dimensions
1.2 Maintenance
Cleaning the unit
Trouble shooting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Menu structure
3. 4 Auto show
3. 5 Static mode
3. 6 Master/Slave mode
3. 7 Linking
3. 9 DMX addressing
3. 10 Connection of the DMX line
3. 11 Construction of the DMX termination
3. 12 DMX control
3. 13 Fixture settings
3. 14 Fixture information
3. 15 White balance calibration
3. 16 W-DMX wireless setting
3.17 Factory reset
3.18 Photometrics
18
3.13 FIXTURE SETTINGS
It is possible to change the parameter values in the following ways:
Dimmer
until shows Dimmer Mode
• Press the button UP/DOWN to select
• Press ENTER button to store, then press MENU to return to main menu
BackLite
• To activate Backlight display press the button MENU so many times until shows Back Light, and press
• Press the button UP/DOWN to select On - 10S - 20S - 30S.
3.14 FIXTURE INFORMATION
Fixture Hours
• Press the button MENU so many times until shows Information.
• Using the button UP/DOWN to select Fixture Hours,
• Then the display will show the working hours.
Version
• Press the button MENU so many times until shows Information
• Select through the button UP/DOWN the Version menu voice.
3.15 WHITE BALANCE
Enter the White balance to adjust the Red,Green,Blue and White
• Press the button MENU so many times until shows White Balance
• Select the color R, G, B, W using the UP/DOWN buttons, then press ENTER.
• Using UP/DOWN button, select the desired color value 125 - 255.
• Press ENTER button to continue to the next color R, G, B, W.
• Continue until the desired mix is obtained.
• Press the MENU button to go back or wait a few seconds to exit the setup menu.
, then press MENU to return to main menu
Press MENU to return to main menu
Press MENU to return to main menu

4
INTRODUCTION
The FUSIONBAR QXV is an outdoor-rated Quad-color (4-in-one) RGBW one-meter LED batten
that delivers vibrant linear color washes and an individually controllable 15 x 1 pixel matrix.
FEATURES
- Deep, saturated, perfectly-mixed colors for wall grazing and linear washes
- Rugged diecast body and production-grade construction
- Color and white presets available via onboard menu or DMX
- Silent operation with advanced fanless thermal management
- Onboard library of 14 dynamic preprogrammed light shows
- Custom color mixing and adjustable white balance
- Menu display backlight auto blackout
- Four selectable dimming curves
- Power linking (IP65 PowerKon In/Out)
- W-DMX onboard
- DMX control
SPECIFICATIONS
Light Source:
Beam Angle:
Field Angle:
Output (lumens):
Output (lux):
Color Output:
Pixel Matrix:
Strobe:
Dimming:
Control:
DMX Channels:
Display:
Mains:
Consumption:
Power connections:
Data connections:
Housing:
Finish:
IP rating:
Cooling:
Ambient operating temps:
Dimensions:
Weight:
10W RGBW LED (x15)
16°
28°
3587 lm
1717 lx @ 5 meters
RGBW
15 x 1
0-30 Hz
4 dimming curve modes
DMX
4 / 6 / 10 / 60 / 65
OLED menu display
100 - 240 VAC, 50/60 Hz
162W
Seetronic IP65 PowerCon In/Out Seetronic
IP65 5-pin XLR In/Out for DMX
Diecast Aluminum
Matte kcalb
IP65
Convection
-20° ~ 40°C
992 x 205 x 160 mm
8.6 KG
17
3.12 DMX CONTROL
Function Value Percent/Setting
1 Red1 000-255 0~100%
2 Green1 000-255 0~100%
3 Blue1 000-255 0~100%
4 White1 000-255 0~100%
......
57 Red 15 000-255 0~100%
58 Green 15 000-255 0~100%
59 Blue 15 000-255 0~100%
60 White15 000-255 0~100%
61 Auto programs
000-010
011-027
028-044
045-061
062-078
079-095
096-112
113-129
130-146
147-163
164-180
181-197
198-214
215-231
232-255
No Function
Auto program 1
Auto program 2
Auto program 3
Auto program 4
Auto program 5
Auto program 6
Auto program 7
Auto program 8
Auto program 9
Auto program 10
Auto program 11
Auto program 12
Auto program 13
Auto program 14
62 Auto Speed 000-255 Auto Speed Slow to Fast
63 Dimmer 000-255 0~100%
64 Strobe 000-010
011-255
No Function
Strobe Slow to Fast
65 Dimmer Speed Mode
000-051
052-101
102-152
153-203
204-255
Preset dimmer speed fr unemyalpsidmo
Dimmer speed mod
Dimmer speed mode1 (fast spee )d
Dimmer speed mode2 (middle spee )d
Dimmer speed mode3 (slow spee )d
65 CHANNEL MODE
9 Auto Speed 000-255 Auto Speed Slow to Fast
10 Dimmer Speed Mode
000-051
052-101
102-152
153-203
204-255
Preset dimmer speed fr unemyalpsidmo
Dimmer speed mod
Dimmer speed mode1 (fast spee )d
Dimmer speed mode2 (middle spee )d
Dimmer speed mode3 (slow spee )d
10 CHANNEL MODE (cont’d)

5
- 1.2 - MAINTENANCE
MAINTENANCE AND CLEANING THE UNIT
• Make sure the area below the installation place is free from unwanted persons during setup.
• All screws used for installing the device and any of its parts should be tightly fastened and should not
be corroded.
deformation.
• The main cables must be in impeccable condition and should be replaced immediately even when a
small problem is detected.
• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or
other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the
main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe
the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might
penetrate the unit and cause damage to it.
TROUBLESHOOTING
Problems Possible causes Checks and remedies
Fixture does not light up
• No mains supply
• Dimmer fader set to 0
• All color faders set to 0
• Faulty LED
• Faulty LED board
• Check the power supply voltage
• Increase the value of the dimmer channels
• Increase the value of the color channels
• Replace the LED board
• Replace the LED board
General low light intensity • Dirty lens assembly
• Misaligned lens assembly
•
• Install lens assembly properly
Fixture does not power up
• No power
• Loose or damaged power cord
• Faulty internal power supply
• Check for power on power outlet
• Check power cord
• Replace internal power supply
Fixture does not respond to DMX
• Wrong DMX addressing
• Damaged DMX cables
• Bouncing signals
• Check control panel and unit addressing
• Check DMX cables
• Install terminator as suggested
Contact an authorized service center in case of technical problems or not reported in the table can not be
resolved by the procedure given in the table.
16
3.12 DMX CONTROL
Function
Value
Percent/Setting
1
Dimmer
000-255
0~100%
2
Red
000-255
0~100%
3
Green
000-255
0~100%
4
Blue
000-255
0~100%
5
White
000-255
0~100%
6 Strobe 000-010
011-255
No Function
Strobe Slow to Fast
7 Color Macro
000~010
011~030
031~050
051~070
071~090
091~110
111~130
131~150
151~170
171~200
201~205
206~210
211-215
216-220
221-225
226-230
231-235
236-240
241-245
246-250
251-255
No Function
R 100%, G 0~100%, B 0%
R 100%~0% , G 100%, B 0%
R 0% , G 100%, B 0~100%
R 0% G 100%~0% B 100%
R 0% ~100% G 0% B 100%
R 100% G 0% B 100%~0%
R 100% G 0%~100% B 0%~100%
R 100%~0% G 100%~0% B 100%
R 100% G 100% B 100%
Color 1
Color 2
Color 3
Color 4
Color 5
Color 6
Color 7
Color 8
Color 9
Color 10
Color 11
8 Auto programs
000-010
011-027
028-044
045-061
062-078
079-095
096-112
113-129
130-146
147-163
164-180
181-197
198-214
215-231
232-255
No Function
Auto program 1
Auto program 2
Auto program 3
Auto program 4
Auto program 5
Auto program 6
Auto program 7
Auto program 8
Auto program 9
Auto program 10
Auto program 11
Auto program 12
Auto program 13
Auto program 14
10 CHANNEL MODE

6
1.3 OPERATING ELEMENTS AND CONNECTIONS
Rear view
DMX Out
Power Out
Mounting
bracket
Tilt
locking
knob
OLED display and
Menu navigation
DMX In
Power In
Quick-Lock
Omega Clamp
Mounts
1. TILT LOCKING KNOB 6. SAFETY CABLE ANCHOR
2. MOUNTING BRACKET 7. GORE VALVE expansion valve
3. POWER OUT (Seetronic IP65 PowerCon) 8. DMX IN (Seetronic IP65 5-pin XLR)
4. DMX OUT (Seetronic IP65 5-pin XLR) 9. POWER IN (Seetronic IP65 PowerCon)
5. QUICK-LOCK MOUNTS for Omega clamps 10. OLED DISPLAY and MENU NAVIGATION
Safety cable
anchor
Gore valve
15
3.12 DMX CONTROL
Function Value Percent/Setting
1 Red 000-255 0~100%
2 Green 000-255 0~100%
3 Blue 000-255 0~100%
4 While 000-255 0~100%
Function Value Percent/Setting
1 Dimmer 000-255 0~100%
2 Red 000-255 0~100%
3 Green 000-255 0~100%
4 Blue 000-255 0~100%
5 While 000-255 0~100%
6 Strobe 000-010
011-255
No Function
Strobe Slow to Fast
Function Value Percent/Setting
1 Red1 000-255 0~100%
2 Green1 000-255 0~100%
3 Blue1 000-255 0~100%
4 White1 000-255 0~100%
......
57 R ed 15 000-255 0~100%
58 Green 15 000-255 0~100%
59 Blue 15 000-255 0~100%
60 White15 000-255 0~100%
4 CHANNEL MODE
6 CHANNEL MODE
60 CHANNEL MODE

7
2.2 DIMENSIONS
992
83
60
160
148.5
205
832 diameter 13
79
14
3.10 CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-
ance and low capacity.
The following diagram shows the connection mode:
ATTENTION
The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would
For those connections the use of balanced microphone cable is not recommended because it cannot
transmit control DMX data reliably.
• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input
of the following unit until all the units are connected in chain.
• When the signal cable has to run longer distance is recommended to insert a DMX termination on the
last unit.
3.11 CONSTRUCTION OF THE DMX TERMINATION
es the end of the line: under certain conditions and with certain cable lengths, this could cause them to
cancel the original signals.
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR
DMX - OUTPUT
XLR socket
DMX - INPUT
XLR plug
Pin1 : GND - Shield
Pin2 : - Negative
Pin3 : + Positive
Pin4 : N/C
Pin5 : N/C

8
- 2 - INSTALLATION
2.1 MOUNTING
FUSIONBAR QXV may be surface-mounted to an even
and be able to support a weight of 10 times of the unit’s weight.
When carrying out any installation, always comply scrupulously with all the regulations (particularly re-
• Install the projector at a suitable location by means of Quick-Lock mounting brackets (1).
• Always additionally secure the projector with the safety cable to prevent falling down (2). Attach
the safety cable
• Floor/wall mounting: a
the locking mechanism of the bracket as necessary (2).
1
2
3
13
3.8 DMX CONFIGURATION
• Press the MENU button un [DMX CHANNEL]
4CH - 6CH - 10CH - 60CH - 65CH) using the UP/DOWN buttons.
3.9 DMX ADDRESSING
• Press the MENU button un [DMX ADDRESS]
• Press UP/DOWN button to select the desired value (001-512). Press and hold to scroll quickly.
• Press ENTER button to store.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
An example with the start address 33 is shown below:
Number of
DMX channels
Start address
(example)
DMX Address
occupied
Next possible start
address for unit No. 1
Next possible start
address for unit No. 2
Next possible start
address for unit No. 3
DMX512 Controller
DMX Address: 33 DMX Address: 45DMX Address: 37 DMX Address: 41
. . . . . . . . . . . .
Example 4 DMX channels configuration
To operate the FUSIONBAR QXV
FUSIONBAR QXV and follow a similar method as shown.
4 33 33-36 37 41 45
FUSIONBAR QXV

9
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Connect the supplied main cable to a socket (100-240V~/50-60Hz). Then the unit is ready for operation
and can be operated via a DMX controller or it independently performs its show program in succession.
3.2 BASIC
Access control panel functions using the four panel buttons located adjacent to the OLED display.
MENU UP DOWN ENTER
Used to access the menu or
to return a previous menu
option
Navigates downwards through
the menu list and increases
the numeric value when in a
function
Navigates upwards through
the menu list and decreases
the numeric value when in
a function
Used to select and store the
current function value or
option within a menu
UP
ENTER
MENU
DOWN
12
3.4 AUTO SHOW
If no DMX control signal is present at the DMX INPUT, the unit independently runs through its
auto show programs:
• Press the MENU button until the display shows Auto Show, then press the button ENTER.
• Press the button UP/DOWN to switch between the show (Auto 1 - 14). The unit will operate in show mode.
• Use the UP/DOWN buttons to select the desired run speed slow-fast (1-100).
• Press the ENTER button to save the setting.
IMPORTANT: Programs Auto 1 - 14 are fully pre-programmed and will not be altered by changes. Instead,
Manual Color mode allows to combine the colors Red - Green - Blue - White.
• Press the button MENU so many times until the display shows Static, then press the button ENTER.
• Through the button UP/DOWN select Manual Color, then press the button ENTER.
• Select the color Red - Green - Blue - White through the buttons UP/DOWN.
• Set the value (000 - 255), through the buttons UP/DOWN.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
3.5 STATIC MODE
• To enable the static mode, press MENU repeatedly until Static shows on the display.
• Press the button ENTER.
• Through the button UP/DOWN select Fixed Color , then press the button ENTER.
• Select the desired preset color (R - G - B - W - GB - RB - RG - RGB - RW - GW - BW - RGW - RBW - GBW - RGBW) using the
button UP/DOWN.
• Press the button ENTER to save the setting.
• Press the MENU button to go back. Or, after a few seconds, the menu returns to the main screen.
3.6 MASTER/SLAVE MODE
This mode will allow you to link up the units together without a controller. Choose a unit to function as the
• Press the button MENU so many times until the display shows Master/Slave and press the button ENTER.
• Press UP/DOWN to set the unit as master or slave (Master/Slave).
• Select the desired program (see section 3.4).
• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the
unit. For longer cable runs, using a DMX terminator as described in this manual is recommended.
3.7 LINKING
master unit.
are connected in a chain.
5-pin

10
3.3 MENU STRUCTURE
Main Menu Submenu Submenu Default settings
DMX Address <001 ~ 512> tluafeD 001
DMX Channel
4 Ch
tluafeD 10 CH
6 Ch
10 Ch
60 Ch
65 Ch
Static
Fixed Color
R
G
B
W
GB
RB
RG
RGB
RW
GW
BW
RGW
RBW
GBW
RGBW
Manual Color Mixer
Red
<0-255>
tluafeD RGBW=255
Green
<0-255>
Blue
<0-255>
White
<0-255>
Auto Show
Auto 1
<1-100>
Default Auto 1; Speed: 100
Auto 2
<1-100>
Auto 3
<1-100>
Auto 4
<1-100>
Auto 5
<1-100>
Auto 6
<1-100>
Auto 7
<1-100>
Auto 8
<1-100>
Auto 9
<1-100>
Auto 10
<1-100>
Auto 11
<1-100>
Auto 12
<1-100>
Auto 13
<1-100>
Auto 14
<1-100>
11
3.3 MENU STRUCTURE (cont’d)
Dimmer Mode
Default
Dimmer 1
Dimmer 2
Dimmer 3
White Balance Default
Manual
Red <125-255>
Green <125-255>
Blue <125-255>
White <125-255>
Wireless Setting
Rece On uafeD lt :
Receive Reset No uafeD lt: No
Yes
Back Light
Default: On
10S
20S
30S
Information Fixture Hours <9999H >
Version <V1.0>
Reset Factory No
Yes
On
Key Lock On
Master/Slave Master
Default Slave
Slave

Outdoor-rated RGBW LED batten
and 15 x 1 pixel mappable matrix
www.showtech.com.au

2
SAFETY
General instruction
• The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make
risk an electric shock.
•
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
• This unit is not for home use, only professional applications.
- in places subject to vibrations or bumps;
- in places with a temperature of over 40 °C.
an inspection or contact the manufacturer directly.
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
• Always additionally secure the projector with the safety rope. When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
• The lamp (LED) shall be changed if it has become damaged or thermally deformed.
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
• Do not touch the product’s housing when operating because it may be very hot.
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
19
3.16 W-DMX WIRELESSSETTING
The FUSIONBAR QXV IP features an onboard W-DMX receiver. By default, W-DMX is OFF. To activate:
• Press the MENU button until the display shows Wireless Setting , then press ENTER.
• Press the UP/DOWN buttons to select Receive On , then press ENTER.
• To reset the onboard W-DMX receiver, select Receive Reset , then press ENTER.
3.17 FACTORY RESET
The FUSIONBAR QXV provides a factory reset function to restore all default values:
• Press the MENU button until the display shows Reset Factory , then press ENTER.
• Press the UP/DOWN buttons to select Yes , then press ENTER.
3.18 PHOTOMETRICS
Beam Angle: 16°
Full
42935 lux 4771 lux 1717 lux
1m 3m 5m

3
Packing content FUSIONBAR QXV
• Mounting bracket (2 pcs.)
• Power cable
• User manual
TABLE OF CONTENTS Safety
General instructions
Warnings and installation precautions
General information
1 Introduction
1. 3 Operating elements and connections
2 Installation
2. 1 Mounting
2.2 Dimensions
1.2 Maintenance
Cleaning the unit
Trouble shooting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Menu structure
3. 4 Auto show
3. 5 Static mode
3. 6 Master/Slave mode
3. 7 Linking
3. 9 DMX addressing
3. 10 Connection of the DMX line
3. 11 Construction of the DMX termination
3. 12 DMX control
3. 13 Fixture settings
3. 14 Fixture information
3. 15 White balance calibration
3. 16 W-DMX wireless setting
3.17 Factory reset
3.18 Photometrics
18
3.13 FIXTURE SETTINGS
It is possible to change the parameter values in the following ways:
Dimmer
until shows Dimmer Mode
• Press the button UP/DOWN to select
• Press ENTER button to store, then press MENU to return to main menu
BackLite
• To activate Backlight display press the button MENU so many times until shows Back Light, and press
• Press the button UP/DOWN to select On - 10S - 20S - 30S.
3.14 FIXTURE INFORMATION
Fixture Hours
• Press the button MENU so many times until shows Information.
• Using the button UP/DOWN to select Fixture Hours,
• Then the display will show the working hours.
Version
• Press the button MENU so many times until shows Information
• Select through the button UP/DOWN the Version menu voice.
3.15 WHITE BALANCE
Enter the White balance to adjust the Red,Green,Blue and White
• Press the button MENU so many times until shows White Balance
• Select the color R, G, B, W using the UP/DOWN buttons, then press ENTER.
• Using UP/DOWN button, select the desired color value 125 - 255.
• Press ENTER button to continue to the next color R, G, B, W.
• Continue until the desired mix is obtained.
• Press the MENU button to go back or wait a few seconds to exit the setup menu.
, then press MENU to return to main menu
Press MENU to return to main menu
Press MENU to return to main menu

4
INTRODUCTION
The FUSIONBAR QXV is an outdoor-rated Quad-color (4-in-one) RGBW one-meter LED batten
that delivers vibrant linear color washes and an individually controllable 15 x 1 pixel matrix.
FEATURES
- Deep, saturated, perfectly-mixed colors for wall grazing and linear washes
- Rugged diecast body and production-grade construction
- Color and white presets available via onboard menu or DMX
- Silent operation with advanced fanless thermal management
- Onboard library of 14 dynamic preprogrammed light shows
- Custom color mixing and adjustable white balance
- Menu display backlight auto blackout
- Four selectable dimming curves
- Power linking (IP65 PowerKon In/Out)
- W-DMX onboard
- DMX control
SPECIFICATIONS
Light Source:
Beam Angle:
Field Angle:
Output (lumens):
Output (lux):
Color Output:
Pixel Matrix:
Strobe:
Dimming:
Control:
DMX Channels:
Display:
Mains:
Consumption:
Power connections:
Data connections:
Housing:
Finish:
IP rating:
Cooling:
Ambient operating temps:
Dimensions:
Weight:
10W RGBW LED (x15)
16°
28°
3587 lm
1717 lx @ 5 meters
RGBW
15 x 1
0-30 Hz
4 dimming curve modes
DMX
4 / 6 / 10 / 60 / 65
OLED menu display
100 - 240 VAC, 50/60 Hz
162W
Seetronic IP65 PowerCon In/Out Seetronic
IP65 5-pin XLR In/Out for DMX
Diecast Aluminum
Matte kcalb
IP65
Convection
-20° ~ 40°C
992 x 205 x 160 mm
8.6 KG
17
3.12 DMX CONTROL
Function Value Percent/Setting
1 Red1 000-255 0~100%
2 Green1 000-255 0~100%
3 Blue1 000-255 0~100%
4 White1 000-255 0~100%
......
57 Red 15 000-255 0~100%
58 Green 15 000-255 0~100%
59 Blue 15 000-255 0~100%
60 White15 000-255 0~100%
61 Auto programs
000-010
011-027
028-044
045-061
062-078
079-095
096-112
113-129
130-146
147-163
164-180
181-197
198-214
215-231
232-255
No Function
Auto program 1
Auto program 2
Auto program 3
Auto program 4
Auto program 5
Auto program 6
Auto program 7
Auto program 8
Auto program 9
Auto program 10
Auto program 11
Auto program 12
Auto program 13
Auto program 14
62 Auto Speed 000-255 Auto Speed Slow to Fast
63 Dimmer 000-255 0~100%
64 Strobe 000-010
011-255
No Function
Strobe Slow to Fast
65 Dimmer Speed Mode
000-051
052-101
102-152
153-203
204-255
Preset dimmer speed fr unemyalpsidmo
Dimmer speed mod
Dimmer speed mode1 (fast spee )d
Dimmer speed mode2 (middle spee )d
Dimmer speed mode3 (slow spee )d
65 CHANNEL MODE
9 Auto Speed 000-255 Auto Speed Slow to Fast
10 Dimmer Speed Mode
000-051
052-101
102-152
153-203
204-255
Preset dimmer speed fr unemyalpsidmo
Dimmer speed mod
Dimmer speed mode1 (fast spee )d
Dimmer speed mode2 (middle spee )d
Dimmer speed mode3 (slow spee )d
10 CHANNEL MODE (cont’d)

5
- 1.2 - MAINTENANCE
MAINTENANCE AND CLEANING THE UNIT
• Make sure the area below the installation place is free from unwanted persons during setup.
• All screws used for installing the device and any of its parts should be tightly fastened and should not
be corroded.
deformation.
• The main cables must be in impeccable condition and should be replaced immediately even when a
small problem is detected.
• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or
other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the
main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe
the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might
penetrate the unit and cause damage to it.
TROUBLESHOOTING
Problems Possible causes Checks and remedies
Fixture does not light up
• No mains supply
• Dimmer fader set to 0
• All color faders set to 0
• Faulty LED
• Faulty LED board
• Check the power supply voltage
• Increase the value of the dimmer channels
• Increase the value of the color channels
• Replace the LED board
• Replace the LED board
General low light intensity • Dirty lens assembly
• Misaligned lens assembly
•
• Install lens assembly properly
Fixture does not power up
• No power
• Loose or damaged power cord
• Faulty internal power supply
• Check for power on power outlet
• Check power cord
• Replace internal power supply
Fixture does not respond to DMX
• Wrong DMX addressing
• Damaged DMX cables
• Bouncing signals
• Check control panel and unit addressing
• Check DMX cables
• Install terminator as suggested
Contact an authorized service center in case of technical problems or not reported in the table can not be
resolved by the procedure given in the table.
16
3.12 DMX CONTROL
Function
Value
Percent/Setting
1
Dimmer
000-255
0~100%
2
Red
000-255
0~100%
3
Green
000-255
0~100%
4
Blue
000-255
0~100%
5
White
000-255
0~100%
6 Strobe 000-010
011-255
No Function
Strobe Slow to Fast
7 Color Macro
000~010
011~030
031~050
051~070
071~090
091~110
111~130
131~150
151~170
171~200
201~205
206~210
211-215
216-220
221-225
226-230
231-235
236-240
241-245
246-250
251-255
No Function
R 100%, G 0~100%, B 0%
R 100%~0% , G 100%, B 0%
R 0% , G 100%, B 0~100%
R 0% G 100%~0% B 100%
R 0% ~100% G 0% B 100%
R 100% G 0% B 100%~0%
R 100% G 0%~100% B 0%~100%
R 100%~0% G 100%~0% B 100%
R 100% G 100% B 100%
Color 1
Color 2
Color 3
Color 4
Color 5
Color 6
Color 7
Color 8
Color 9
Color 10
Color 11
8 Auto programs
000-010
011-027
028-044
045-061
062-078
079-095
096-112
113-129
130-146
147-163
164-180
181-197
198-214
215-231
232-255
No Function
Auto program 1
Auto program 2
Auto program 3
Auto program 4
Auto program 5
Auto program 6
Auto program 7
Auto program 8
Auto program 9
Auto program 10
Auto program 11
Auto program 12
Auto program 13
Auto program 14
10 CHANNEL MODE

6
1.3 OPERATING ELEMENTS AND CONNECTIONS
Rear view
DMX Out
Power Out
Mounting
bracket
Tilt
locking
knob
OLED display and
Menu navigation
DMX In
Power In
Quick-Lock
Omega Clamp
Mounts
1. TILT LOCKING KNOB 6. SAFETY CABLE ANCHOR
2. MOUNTING BRACKET 7. GORE VALVE expansion valve
3. POWER OUT (Seetronic IP65 PowerCon) 8. DMX IN (Seetronic IP65 5-pin XLR)
4. DMX OUT (Seetronic IP65 5-pin XLR) 9. POWER IN (Seetronic IP65 PowerCon)
5. QUICK-LOCK MOUNTS for Omega clamps 10. OLED DISPLAY and MENU NAVIGATION
Safety cable
anchor
Gore valve
15
3.12 DMX CONTROL
Function Value Percent/Setting
1 Red 000-255 0~100%
2 Green 000-255 0~100%
3 Blue 000-255 0~100%
4 While 000-255 0~100%
Function Value Percent/Setting
1 Dimmer 000-255 0~100%
2 Red 000-255 0~100%
3 Green 000-255 0~100%
4 Blue 000-255 0~100%
5 While 000-255 0~100%
6 Strobe 000-010
011-255
No Function
Strobe Slow to Fast
Function Value Percent/Setting
1 Red1 000-255 0~100%
2 Green1 000-255 0~100%
3 Blue1 000-255 0~100%
4 White1 000-255 0~100%
......
57 R ed 15 000-255 0~100%
58 Green 15 000-255 0~100%
59 Blue 15 000-255 0~100%
60 White15 000-255 0~100%
4 CHANNEL MODE
6 CHANNEL MODE
60 CHANNEL MODE

7
2.2 DIMENSIONS
992
83
60
160
148.5
205
832 diameter 13
79
14
3.10 CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-
ance and low capacity.
The following diagram shows the connection mode:
ATTENTION
The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would
For those connections the use of balanced microphone cable is not recommended because it cannot
transmit control DMX data reliably.
• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input
of the following unit until all the units are connected in chain.
• When the signal cable has to run longer distance is recommended to insert a DMX termination on the
last unit.
3.11 CONSTRUCTION OF THE DMX TERMINATION
es the end of the line: under certain conditions and with certain cable lengths, this could cause them to
cancel the original signals.
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR
DMX - OUTPUT
XLR socket
DMX - INPUT
XLR plug
Pin1 : GND - Shield
Pin2 : - Negative
Pin3 : + Positive
Pin4 : N/C
Pin5 : N/C

8
- 2 - INSTALLATION
2.1 MOUNTING
FUSIONBAR QXV may be surface-mounted to an even
and be able to support a weight of 10 times of the unit’s weight.
When carrying out any installation, always comply scrupulously with all the regulations (particularly re-
• Install the projector at a suitable location by means of Quick-Lock mounting brackets (1).
• Always additionally secure the projector with the safety cable to prevent falling down (2). Attach
the safety cable
• Floor/wall mounting: a
the locking mechanism of the bracket as necessary (2).
1
2
3
13
3.8 DMX CONFIGURATION
• Press the MENU button un [DMX CHANNEL]
4CH - 6CH - 10CH - 60CH - 65CH) using the UP/DOWN buttons.
3.9 DMX ADDRESSING
• Press the MENU button un [DMX ADDRESS]
• Press UP/DOWN button to select the desired value (001-512). Press and hold to scroll quickly.
• Press ENTER button to store.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
An example with the start address 33 is shown below:
Number of
DMX channels
Start address
(example)
DMX Address
occupied
Next possible start
address for unit No. 1
Next possible start
address for unit No. 2
Next possible start
address for unit No. 3
DMX512 Controller
DMX Address: 33 DMX Address: 45DMX Address: 37 DMX Address: 41
. . . . . . . . . . . .
Example 4 DMX channels configuration
To operate the FUSIONBAR QXV
FUSIONBAR QXV and follow a similar method as shown.
4 33 33-36 37 41 45
FUSIONBAR QXV

9
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Connect the supplied main cable to a socket (100-240V~/50-60Hz). Then the unit is ready for operation
and can be operated via a DMX controller or it independently performs its show program in succession.
3.2 BASIC
Access control panel functions using the four panel buttons located adjacent to the OLED display.
MENU UP DOWN ENTER
Used to access the menu or
to return a previous menu
option
Navigates downwards through
the menu list and increases
the numeric value when in a
function
Navigates upwards through
the menu list and decreases
the numeric value when in
a function
Used to select and store the
current function value or
option within a menu
UP
ENTER
MENU
DOWN
12
3.4 AUTO SHOW
If no DMX control signal is present at the DMX INPUT, the unit independently runs through its
auto show programs:
• Press the MENU button until the display shows Auto Show, then press the button ENTER.
• Press the button UP/DOWN to switch between the show (Auto 1 - 14). The unit will operate in show mode.
• Use the UP/DOWN buttons to select the desired run speed slow-fast (1-100).
• Press the ENTER button to save the setting.
IMPORTANT: Programs Auto 1 - 14 are fully pre-programmed and will not be altered by changes. Instead,
Manual Color mode allows to combine the colors Red - Green - Blue - White.
• Press the button MENU so many times until the display shows Static, then press the button ENTER.
• Through the button UP/DOWN select Manual Color, then press the button ENTER.
• Select the color Red - Green - Blue - White through the buttons UP/DOWN.
• Set the value (000 - 255), through the buttons UP/DOWN.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
3.5 STATIC MODE
• To enable the static mode, press MENU repeatedly until Static shows on the display.
• Press the button ENTER.
• Through the button UP/DOWN select Fixed Color , then press the button ENTER.
• Select the desired preset color (R - G - B - W - GB - RB - RG - RGB - RW - GW - BW - RGW - RBW - GBW - RGBW) using the
button UP/DOWN.
• Press the button ENTER to save the setting.
• Press the MENU button to go back. Or, after a few seconds, the menu returns to the main screen.
3.6 MASTER/SLAVE MODE
This mode will allow you to link up the units together without a controller. Choose a unit to function as the
• Press the button MENU so many times until the display shows Master/Slave and press the button ENTER.
• Press UP/DOWN to set the unit as master or slave (Master/Slave).
• Select the desired program (see section 3.4).
• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the
unit. For longer cable runs, using a DMX terminator as described in this manual is recommended.
3.7 LINKING
master unit.
are connected in a chain.
5-pin

10
3.3 MENU STRUCTURE
Main Menu Submenu Submenu Default settings
DMX Address <001 ~ 512> tluafeD 001
DMX Channel
4 Ch
tluafeD 10 CH
6 Ch
10 Ch
60 Ch
65 Ch
Static
Fixed Color
R
G
B
W
GB
RB
RG
RGB
RW
GW
BW
RGW
RBW
GBW
RGBW
Manual Color Mixer
Red
<0-255>
tluafeD RGBW=255
Green
<0-255>
Blue
<0-255>
White
<0-255>
Auto Show
Auto 1
<1-100>
Default Auto 1; Speed: 100
Auto 2
<1-100>
Auto 3
<1-100>
Auto 4
<1-100>
Auto 5
<1-100>
Auto 6
<1-100>
Auto 7
<1-100>
Auto 8
<1-100>
Auto 9
<1-100>
Auto 10
<1-100>
Auto 11
<1-100>
Auto 12
<1-100>
Auto 13
<1-100>
Auto 14
<1-100>
11
3.3 MENU STRUCTURE (cont’d)
Dimmer Mode
Default
Dimmer 1
Dimmer 2
Dimmer 3
White Balance Default
Manual
Red <125-255>
Green <125-255>
Blue <125-255>
White <125-255>
Wireless Setting
Rece On uafeD lt :
Receive Reset No uafeD lt: No
Yes
Back Light
Default: On
10S
20S
30S
Information Fixture Hours <9999H >
Version <V1.0>
Reset Factory No
Yes
On
Key Lock On
Master/Slave Master
Default Slave
Slave