Shure ULX-D User manual

Sistem Mikrofon Nirkabel Digital ULX-D
ULX-D 数字式无线话筒系统
ULX-D 디지털 무선 마이크 시스템
ULX-Dデジタルワイヤレスマイクロホンシステム
Цифровая беспроводная микрофонная система ULX-D
Sistema de Microfone Sem Fio Digital ULX-D
Sistema radiomicrofonico digitale ULX-D
Sistema de micrófonos inalámbricos digitales ULX-D
Digitales drahtloses Mikrofonsystem ULX-D
Système de microphone sans fil numérique ULX-D
ULX-D 數位式無線話筒系統
ULX-D Digital Wireless Microphone System
©2011 Shure Incorporated
Printed in USA
27A16235 (Rev. 2)
ULX-D

IMPORTANT SAFETY INSTRUCTIONS
1. READtheseinstructions.
2. KEEPtheseinstructions.
3. HEEDallwarnings.
4. FOLLOWallinstructions.
5. DONOTusethisapparatusnearwater.
6. CLEANONLYwithdrycloth.
7. DONOTblockanyventilationopenings.Installinaccordancewiththemanufacturer’s
instructions.
8. DONOTinstallnearanyheatsourcessuchasradiators,heatregisters,stoves,orother
apparatus(includingamplifiers)thatproduceheat.
9. DONOTdefeatthesafetypurposeofthepolarizedorgroundingtypeplug.Apolarized
plughastwobladeswithonewiderthantheother.Agroundingtypeplughastwoblades
andathirdgroundingprong.Thewiderbladeorthethirdprongareprovidedforyour
safety.Iftheprovidedplugdoesnotfitintoyouroutlet,consultanelectricianforreplace-
mentoftheobsoleteoutlet.
10. PROTECTthepowercordfrombeingwalkedonorpinched,particularlyatplugs,conve-
niencereceptacles,andthepointwheretheyexitfromtheapparatus.
11. ONLYUSEattachments/accessoriesspecifiedbythemanufacturer.
12. USEonlywithacart,stand,tripod,bracket,ortablespecifiedbythemanu-
facturer,orsoldwiththeapparatus.Whenacartisused,usecautionwhen
movingthecart/apparatuscombinationtoavoidinjuryfromtip-over.
13. UNPLUGthisapparatusduringlightningstormsorwhenunusedforlong
periodsoftime.
14. REFERallservicingtoqualifiedservicepersonnel.Servicingisrequiredwhentheap-
paratushasbeendamagedinanyway,suchaspowersupplycordorplugisdamaged,
liquidhasbeenspilledorobjectshavefallenintotheapparatus,theapparatushasbeen
exposedtorainormoisture,doesnotoperatenormally,orhasbeendropped.
15. DONOTexposetheapparatustodrippingandsplashing.DONOTputobjectsfilledwith
liquids,suchasvases,ontheapparatus.
16. TheMAINSplugoranappliancecouplershallremainreadilyoperable.
17. TheairbornenoiseoftheApparatusdoesnotexceed70dB(A).
18. ApparatuswithCLASSIconstructionshallbeconnectedtoaMAINSsocketoutletwitha
protectiveearthingconnection.
19. Toreducetheriskoffireorelectricshock,donotexposethisapparatustorainor
moisture.
20. Donotattempttomodifythisproduct.Doingsocouldresultinpersonalinjuryand/or
productfailure.
Thissymbolindicatesthatdangerousvoltageconstitutingariskof
electricshockispresentwithinthisunit.
Thissymbolindicatesthatthereareimportantoperatingandmainte-
nanceinstructionsintheliteratureaccompanyingthisunit.
WARNING: ThisproductcontainsachemicalknowntotheStateofCaliforniatocause
cancerandbirthdefectsorotherreproductiveharm.
iii

iv

중요 안전 지침
1. 이지침을정독해주십시오.
2. 이지침을잘보관해주십시오.
3. 모든경고를유의하십시오.
4. 모든지침을준수하십시오.
5. 이기기를물가까이에두고사용하지마십시오.
6. 마른수건으로만닦으십시오.
7. 통풍구를막지마십시오.제조업체의지침에따라설치하십시오.
8. 난방기,방열조절기,스토브,기타열을발산하는기기(앰프포함)근처에설
치하지마십시오.
9. 안전을위해유극또는접지타입의플러그를반드시사용하십시오.유극유형
의플러그에는폭이다른핀이있습니다.접지형플러그에는두개의핀과하
나의접지단자가있습니다.넓은핀이나접지단자는사용자의안전을위한
것입니다.제공된플러그가콘센트에맞지않으면전기기사에게문의하여구
형콘센트를교체하십시오.
10.전원코드는밟히지않도록주의하고특히전원플러그사이,접속소켓및기
기에서나오는부분에전원코드가끼이않도록보호하십시오.
11.제조업체가지정한부속품/부품만사용하십시오.
12.제조업체에서지정하거나기기와함께판매되는카트,스탠드,받
침대,브라켓또는테이블에서만사용하십시오.카트를사용하는
경우,이동시카트와기기가넘어져부상을입지않도록주의하
십시오.
13.낙뢰시또는장기간동안사용하지않을때는기기의전원을빼놓으십시오.
14.모든서비스는자격을갖춘서비스전문가에게의뢰하십시오.전원코드나플
러그가손상된경우,기기안으로액체를들어가거나물건을떨어뜨린경우,
기기가비나물에젖은경우,기기가정상적으로작동하지않는경우또는기
기를떨어뜨린경우와같이기기가손상되었을때는서비스를받아야합니다.
15.기기에물을떨어뜨리거나뿌리지마십시오.물병과같이물이담긴물체를기
기위에올려놓지마십시오.
16.MAINS플러그나기기용커플러는작동가능한상태로남아있어야합니다.
17.AC어댑터의공기매개잡음은70dB을초과하지않아야합니다.
18.CLASSI구조의기기는MAINS소켓콘센트에보호접지연결방식으로연결
되어야합니다.
19.화재나감전위험을줄이려면이기기를빗물또는습기에노출시키지마십
시오.
20.이제품을고치려고시도하지마십시오.그렇게하면사람이다치거나제품이
고장을일으킬수있습니다.
이기호는기기에전기쇼크위험을유발하는위험한전압이
흐른다는것을의미합니다.
이기호는이기기와함께제공된문서에중요한작동및유지
보수지침의내용이들어있다는것을의미합니다.
v

vi

vii

Petunjuk Memulai Cepat
快速入門說明
快速入门说明
12V OUT
150mA
12V OUT
150mA
15V0.6A
line
mic
ULXD4
www.shure.com
power mic / line inst / auxantenna . B antenna .A
150mA
ULXD4
DigitalWirelessReceiver
sync push
control
ENTER
EXIT
SCAN
RF
AB
OL
OL
gain poweraudio
12V OUT
150 mA 12V OUT
150 mA
15V 0.6A line
mic
ULXD4
www.shure.com
power mic / line inst / aux antenna . B antenna . A
control RF audio gain power
push
SCAN
sync
EXIT
ENTER
power
on
n
o
2DXLU
on
ULXD1
ULXD1
push
EXIT
SCAN
push
EXIT
SCAN
ULXD4
Digital Wireless Receiver
sync push
control
ENTER
EXIT
SCAN
RF
A B
OL
OL
gain poweraudio
ULXD4
Digital Wireless Receiver
sync push
control
ENTER
EXIT
SCAN
RF
A B
OL
OL
gain poweraudio
push
EXIT
SCAN
control RF audio gain power
push
SCAN
sync
EXIT
ENTER
on
ULXD2
control RF audio gain power
push
SCAN
sync
EXIT
ENTER
sync
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
a
a
a
b
b
b
c
4
ULXD4
Digital Wireless Receiver
sync
3
1 2
AA SB900
b
ac
on
ULXD2
on
ULXD2
12V OUT
150mA
12V OUT
150mA
15V0.6A
line
mic
ULXD4
ww
w
.shure.com
power
mic / line
inst / aux
antenna . B
antenna .
A
150mA
12V OUT
150 mA
line
mic
ULXD4
ww
w
.shure.com
mic / line inst / aux
antenna . B
15V 0.6A
power
12V OUT
150mA
12V OUT
150mA
line
mic
ULXD4
ww
w
.shure.com
15V0.6A
power
mic / line
inst / aux
antenna . B
antenna .
A
45°
<
1
5
c
m
(
8
i
n
.
)
!
!
!
!
!
!
!
! !
!
!
!
!
!
!
!
!
!
!
!
!
SCAN COMPLETE
G:01 CH:21
485.775 MHz
Rssi: -118 dBm
빠른 시작 설명서
クイックスタート操作ガイド
Краткое руководство
Instruções para Início Rápido
Istruzioni di avviamento rapido
Instrucciones de arranque rápido
Kurzanleitung
Instructions de mise en oeuvre rapide
Quickstart Instructions
viii

Receiver
Front Panel
① Sync Button
Press the sync button while the receiver and transmitter IR windows are
aligned to transfer settings from the receiver to the transmitter
② Infrared (IR) Sync Window
Sends IR signal to the transmitter for sync
③ Network Icon
Illuminates when the receiver is connected with other Shure devices on
the network. IP Address must be valid to enable networked control
④ Encryption Icon
Illuminates when AES-256 encryption is activated: Utilities > Encryption
⑤ LCD Panel
Displays settings and parameters
⑥ Scan Button
Press to find the best channel or group
⑦ Menu Navigation Buttons
Use to select and navigate through parameter menus
⑧ Control Wheel
Push to select menu items for editing, turn to edit a parameter value
⑨ RF Diversity LEDs
Indicate antenna status:
• Blue = normal RF signal between the receiver and transmitter
• Red = interference detected
• Off = No RF connection between the receiver and transmitter
Note: the receiver will not output audio unless one blue LED is illuminated
⑩ RF Signal Strength LEDs
Indicate the RF signal strength from the transmitter:
• Amber = Normal (-90 to -70 dBm)
• Red = Overload (greater than -25 dBm)
⑪ Audio LEDs
Indicate average and peak audio levels:
LED Audio Signal Level Description
Red (6) -0.1 dBFS Overload/ limiter
Yellow (5) -6 dBFS Normal peaks
Yellow/ Green (4) -12 dBFS
Green (3) -20 dBFS Signal Present
Green (2) -30 dBFS
Green (1) -40 dBFS
⑫ Gain Buttons
Adjust channel gain
⑬ Power Switch
Powers the unit on or off
ULXD4
Digital Wireless Receiver
sync push
control
ENTER
EXIT
SCAN
RF
A B
OL
OL
gain poweraudio
3 4 5
89
10 11 6
7
12 13
1 2
Adjusting Gain
Press the ▲▼ gain buttons on the front of the receiver
to incrementally adjust gain from -18 to +42 dB.
ULXD4
Digital Wireless Receiver
sync push
control
ENTER
EXIT
SCAN
RF
A B
OL
OL
gain poweraudio
RF
AB
L
OL
gain poweraudio
General Description
Shure ULX-D Digital Wireless offers uncompromising audio quality and RF performance, with intelligent, encryption-enabled hardware and advanced re-
chargeability options for professional sound reinforcement.
A breakthrough in wireless audio quality, Shure digital processing enables ULX-D to deliver the purest reproduction of source material ever available in a
wireless system. Extended 20 Hz – 20 KHz frequency range and totally flat response captures every detail with clarity, presence, and incredibly accurate low-
end and transient response. At greater than 120 dB, ULX-D delivers wide dynamic range for excellent signal-to-noise performance. For added convenience,
proprietary Shure Gain Ranging optimizes the system’s dynamic range for any input source, eliminating the need for transmitter gain adjustments.
In RF performance, ULX-D sets the bar for wireless channel efficiency and signal stability. Minimized intermodulation allows more transmitters to operate si-
multaneously over one TV channel than any other system. Rock-solid RF signal with no audio artifacts extends over the entire 100 meter line-of-sight range,
even using standard dipole antennas. For applications where secure transmission is required, ULX-D offers Advanced Encryption Standard (AES) 256-bit
encrypted signal for unbreachable privacy.
Advanced Lithium-ion rechargeability provides extended transmitter battery life over alkaline batteries, battery life metering in hours and minutes accurate to
within 15 minutes, and detailed tracking of battery health status.
Generations ahead of any other available system in its class, ULX-D brings a new level of performance to professional sound reinforcement.
System Gain Control
The gain control on the receiver sets the audio signal level for the entire system.
This allows adjustments to be made during a live performance. It is not neces-
sary to change the gain on the transmitter (mic offset) to optimize the gain struc-
ture. Any required changes to gain should be made from the receiver.
Full Manual Online
This is the quick-reference version of the user guide. For information on the following topics, visit www.shure.com to download the comprehensive manual:
• Multiple systems setup
• RF and hardware presets
• LCD warnings
• Networking details
• Firmware updates
• AMX and Crestron connections
• Troubleshooting
• Product specifications and wiring diagrams
• Compatible frequencies chart
1

Transmitters
① Power LED
• Green = unit is powered on
• Red = low battery or battery error (see Troubleshooting)
• Amber = power switch is disabled
② On/Off Switch
Powers the unit on or off
③ TA4M Input Jack
Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument
cable
④ LCD Display:
View menu screens and settings. Press any control button to activate the
backlight
⑤ Infrared (IR) Port
Align with the receiver IR port during an IR Sync for automated transmitter
programming
⑥ Menu Navigation Buttons
Use to navigate through parameter menus and change values.
exit Acts as a 'back' button to return to previous menus or pa-
rameters without confirming a value change
enter Enters menu screens and confirms parameter changes
▼▲ Use to scroll through menu screens and to change param-
eter values
⑦ Battery Compartment
Requires Shure SB900 rechargeable battery or 2 AA batteries.
⑧ AA Battery Adapter
Handheld: rotate and store in the battery compartment to use a Shure
rechargeable battery pack
Bodypack: remove to accommodate a Shure rechargeable battery pack
⑨ Detachable Bodypack Antenna
For RF signal transmission
⑩ Integrated Antenna
For RF signal transmission
⑪ Microphone Cartridge
See Optional Accessories for a list of compatible cartridges
on
ULXD2
⑧
⑩
⑪
②
④
⑤
⑥
⑦
Back Panel
① RF Antenna Diversity Input Jack (2)
For antenna A and antenna B.
② Power Supply Jack
Connect the supplied 15 V DC external power supply
③ Network Speed LED (Amber)
• Off = 10 Mbps
• On = 100 Mbps
④ Ethernet Port
Connect to an Ethernet network to enable remote control and monitoring
⑤ Network Status LED (Green)
• Off = no network link
• On = network link active
• Flashing = network link active, flash rate corresponds to traffic volume
⑥ Mic/Line Switch
Applies a 30 dB pad in mic position (XLR output only)
⑦ Balanced XLR Audio Output
Connect to a mic or line level input
⑧ Balanced 1/4" (6.35 mm) TRS Audio Output
Connect to a mic or line level input
12V OUT
150 mA
12V OUT
150 mA
line
mic
ULXD4
www.shure.com
15V 0.6A
power mic / line inst / auxantenna . B antenna . A
23 4 5
1 1
86 7
Receiver Output Level
The following table describes the typical total system gain from the audio
input to the receiver outputs:
Output Jack System Gain (gain control = 0dB)
1/4" TRS +18 dB
XLR (line setting) +24 dB
XLR (mic setting) -6 dB*
*This setting matches a typical wired SM58 audio signal level.
ULXD1
①② ③
④
⑤
⑥
⑦
⑧
⑨
2

Home Screen
34
5
16
23 4
1
2
5
6
7
8
Receiver
① Receiver Information
Use UTILITIES > HOME INFO to change the home screen display
② Gain Setting
-18 to +42 dB, or Mute
③ Mic. Offset Indicator
Indicates offset gain is added to the transmitter
④ Transmitter Settings
The following information cycles when a transmitter is tuned to the
receiver's frequency:
• Transmitter Type
• Input Pad (Bodypack only)
• RF Power Level
• Transmitter Lock Status
⑤ Battery Runtime Indicator
Shure SB900 battery: runtime is displayed in minutes remaining
AA Batteries: runtime is displayed with a 5-bar indicator
⑥ TV Channel
Displays the TV channel that contains the tuned frequency
Encryption
ULXD features Advanced Encryption Standard (AES-256) encryption,
conforming to the US Government National Institute of Standards and
Technology (NIST) publication FIPS-197.
1. Enable encryption on the receiver: UTILITIES > ENCRYPTION.
The encryption symbol illuminates green and the LCD displays
SYNC NOW FOR ENCYPTION.
2. Sync the transmitter to the receiver. The encryption symbol displays on
the transmitter.
Note: Any change to the encryption status on the receiver requires a sync
to transfer the setting to the transmitter. The Encryption Mismatch warning
will display on the receiver LCD panel if they are not on the same setting.
Transmitter Setting Icons
Display Icon Transmitter Setting
-12 dB Bodypack input is attenuated 12 dB
Offset gain is added to the transmitter
Lo 1 mW RF power level
Nm 10 mW RF power level
Hi 20 mW RF power level
MMenu is locked
PPower is locked
-No TX- No RF connection between a receiver and transmitter
Transmitter
① Transmitter Information
Scroll ▲▼ at the home screen to change the display
② Power Lock Indicator
Indicates power switch is disabled
③ Battery Runtime Indicator
Shure SB900 battery: runtime is displayed in minutes remaining
AA Batteries: runtime is displayed with a 5-bar indicator
④ Menu Lock Indicator
Indicates menu navigation buttons are disabled
⑤ Mic. Offset
Displays microphone offset gain value
⑥ RF Power
Displays RF power setting
⑦ Bodypack Input Pad
The input signal is attenuated 12 dB
⑧ Encryption Icon
Indicates encryption is enabled on the receiver and has been transferred
to the transmitter from a sync
Band Frequency Range
( MHz)
Power ( mW)
G50 470 to 534 1/10/20
G51 470 to 534 1/10/20
G52 479 to 534 1/10
H51 534 to 598 1/10/20
H52 534 to 565 1/10
J50 572 to 636 1/10/20
K51 606 to 670 1/10
L50 632 to 696 1/10/20
L51 632 to 696 1/10/20
Band Frequency Range
( MHz)
Power ( mW)
P51 710 to 782 1/10/20
R51 800 to 810 1/10/20
JB (Tx
only)
806 to 810 1/10
AB (Rx
and Tx)
770 to 810 "A" band (770.250-805.750): 1/10/20
"B" band (806.125-809.750): 1/10
Q51 794 to 806 1/10/20
X50 925 to 932 1/10
Frequency Range and Transmitter Output Power
3