Shure 577B User manual

Model 577B User Guide
©2005, Shure Incorporated
27C1128 (Rev. 4)
Printed in U.S.A.
NOISE-CANCELING HANDHELD DYNAMIC MICROPHONE
GENERAL
The Shure Model 577B SONOBAR®Microphone is a handheld
dynamic microphone designed for communications and paging
applications that require highly intelligible, low noise output. It can
be used in all types of mobile communications, from amateur radio
to helicopter news and traffic reports. It is also suitable for public
address and paging systems in noisy areas such as factories,
airport terminals, and restaurants.
The 577B represents a significant improvement over most
microphones with anti-noise features. Shaped frequency
response, directionality, and distant sound discrimination
contribute to total noise reduction. The microphone operates on
the pressure-gradient principle and has two sound entry ports
spaced a small distance apart.
The modular design of the 577B greatly facilitates field servicing.
The cartridge, switch, and cable can be replaced in a matter of
minutes, if necessary.
The 577B is built to withstand mechanical shocks, vibration, high
temperatures, and humidity. The exclusive ARMO-DUR® case is
impervious to oil, grease, fumes, salt spray, sun, and corrosion.
The “Million-Cycle” press-to-talk switch ensures years of reliable
service.
A mounting bracket is supplied to provide convenient hang-up
when the microphone is not in use.
Features
•
Frequency response tailored for close-talk operation
• Extremely effective noise cancellation
• Dynamic microphone cartridge
• Modular design
• “Million-cycle” leaf-type press-to-talk switch
• TRIPLE-FLEX
®
cable provides three to four times the flex life of
most coiled cords
• Rugged ARMO-DUR
®
case
• Built-in hang-up button and supplied mounting bracket
OPERATION
For optimum performance and maximum rejection of background
noise, place your upper lip against the lip guard, approximately 25
mm (1 in.) from the grille. Hold down the push-to-talk button while
talking normally.
INTERNAL CONNECTIONS
The 577B is a balanced-line, low-impedance dynamic microphone.
It is designed for direct connection to low-impedance microphone
inputs and/or installations where long cable lengths are needed. It
includes a four-conductor (two conductors shielded) coiled-cord
cable and a double-pole, single-throw, leaf-type switch. The
NATURAL and GREEN leads are the “hot” audio conductors; the
shield is connected to microphone circuit ground. The RED and
BLACK leads control the switch circuit. The microphone circuit is
open when the switch is open, but can be easily modified for
normally shorted operation. Refer to Figure 1.
INTERNAL CONNECTIONS
FIGURE 1
TABLE 1. CABLE-TO-CONNECTOR WIRING
INPUT TYPE WIRE
COLOR
FUNCTION XLR
CONNECT
OR
1/4 INCH
PHONE
PLUG
NATURAL AUDIO + PIN 2 TIP
BALANCED GREEN AUDIO – PIN 3 RING
SHIELD CHASSIS
GROUND
PIN 1 SLEEVE
NATURAL AUDIO -- TIP
UNBALANCED GREEN AUDIO
GROUND
-- SLEEVE
SHIELD CHASSIS
GROUND
-- SLEEVE

2
CIRCUIT MODIFICATION
To modify the microphone circuit for normally shorted operation,
proceed as follows:
1. Remove the three No. 6 Phillips screws from the back of the
microphone case.
2. Separate the front and back sections of the case, and remove
the press-to-talk switch button.
3. Unsolder or clip the GREEN cable lead from the press-to-talk
switch solder lug.
4. Solder the GREEN cable lead to the GREEN cartridge lead on
the press-to-talk switch solder lug.
5. Replace the press-to-talk switch button in the front section of
the case, then join the case halves together and install the No.
6 Phillips screws removed in Step 1 above.
SPECIFICATIONS
Type
Dynamic, noise-canceling
Frequency Response
100 to 5,000 Hz (see Figure 2)
TYPICAL FREQUENCY RESPONSE
FIGURE 2
Impedance (at 1000 Hz)
Rated at 150 Ω(175 Ωactual) for connection to microphone
inputs rated at 19 to 300 Ω.
Output Level (at 1,000 Hz, 5/16 in.)
Open Circuit Voltage-66.0 dBV/Pa (0.5 mV)
0 dB = 1 volt per 1 Pascal/94 dB SPL
Hum Sensitivity
Equivalent to 32 dB SPL in 1 millioersted field
Operating Temperature Range
-40°to 74°C (-40°to 165°F)
Switch Type
Double-pole, single-throw, leaf-type, push-to-talk
Cable
Non-detachable. 1.8 m (6 ft), neoprene-jacketed coil cord,
four-conductor (two conductors shielded).
Case
Two-tone gray, high-impact ARMO-DUR®
Dimensions
See Figure 3
OVERALL DIMENSIONS
FIGURE 3
Net Weight
330 grams (11.6 oz)
CERTIFICATION
Eligible to bear CE Marking. Conforms to European EMC Directive
89/336/EEC. Meets applicable tests and performance criteria in
European Standard EN55103 (1996) parts 1 and 2, for residential
(E1) and light industrial (E2) environments.
SUPPLIED ACCESSORY
Mounting Bracket (3 per kit) .......................................... RK6MB
REPLACEMENT PARTS
Cartridge ........................................................................... R98B
Cable .................................................................................. C117
Switch............................................................................ RK338S
SERVICE INFORMATION
For additional service or parts information, please contact Shure's
Service department at 1-800-516-2525. Outside the United States,
please contact your authorized Shure Service Center.
20 200001000 1000050 100 98765432 98765432
+10
0
–10
Hz
Bd
MICROPHONE
MOUNTING BRACKET
46 mm
36.5 mm
4.7 mm
34.5 mm
10.3 mm
9.5 mm
9.1 mm
(23/64 IN.)
(3/8 IN.)
(1-13/16 IN.)
(1-7/16 IN.)
(3/16 IN.)
(1-23/64 IN.)
(13/32 IN.)
MOUNTING HOLES,
CLEARANCE FOR
No. 8 SCREWS
67 mm
(2-5/8 IN.)
94 mm
(3-11/16 IN.)
45 mm
(1-25/32 IN.)
8 mm
(5/16 IN.)
14 mm
(9/16 IN.)
41 mm
(1-19/32 IN.)
19 mm
(3/4 IN.)
18 mm
(23/32 IN.) 4.8 mm
(3/16 IN.)
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: [phone] U.S. Fax: [phone] Intl Fax: [phone]
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: [phone] Fax: [phone]
Asia, Pacific:
Shure Asia Limited, Phone: [phone] Fax: [phone]