Shure ES50 User manual

222 HARTCEY AVE., EVANSTON. IL. 60204 U.S.A.
DATA
SHEET
MODEL ES50
AREA CODE 312/328-9000 . CABLE: SHUREMICRO
UNIDIRECTIONAL DYNAMIC MICROPHONE
FOR ACOUSTICALLY EQUALIZED SOUND
General: The basic role of the microphone in an equal-
ized sound system is to pick up the program source
without disturbing the uniformly distributed sound-
adjustment which has been performed on the system.
The feedback threshold, measured in half-octave
bands, gives an overall picture of the performance
potential of the microphone used in an equalized sound
system. This measurement includes the effects of fre-
quency response and polar response.
The design of the Model ES50 microphone has
been specifically optimized to operate in equalized
sound systems and to maintain a uniform feedback
threshold characteristic.
The feedback threshold curve of the Model ES50
is shown in Fig. A.
NOTE that the feedback threshold in the useful
operating range of 110 Hz. to 5000 Hz. is main-
tained at uniform level. This factor is imperative
for optimum results from an equalized system at
minimal costs. In the critical range above 5000 Hz.
the response of the ES50 has been smoothly
tailored to increase the feedback rejection in this
region.
A further requirement of a microphone for use in
an equalized system is its uniform phasing-the Model
ES50 is 100% phase checked.
The microphone features:
m
Response specially tailored for use in equalized
sound systems
True cardioid pickup pattern: symmetrical about
axis and uniform at all frequencies
Cartridge shock mounted for quiet operation
Versatility-for use in the hand or on a stand
8
An adjustable swivel adapter that enables you to
aim the microphone where you want it. Swivel
also allows for quick removal for use as a hand
microphone
The Model ES50 is low impedance and is designed
for connection to a 25 to 200 ohm line or input. This is
recommended where long cable lengths are required
or where there are conditions of severe hum disturb-
ance. To use Model ES50 with a high impedance ampli-
fier, use a Shure Model A95A Line Matching Trans-
former.
FURNISHED ACCESSORIES
Swivel Adapter ............................. A25B
OPTIONAL ACCESSORIES
Line Matching Transformer .................. A95A
Vibration-Isolation Stand .................... S39A
Desk Stand ................................. S33B
Quick Disconnect Isolation Unit ................ A47
ARCHITECT'S SPECIFICATIONS
The microphone shall be Shure Model ES50 or equiv-
alent. A moving coil (dynamic) microphone with a fre-
quency and polar response especially tailored for
equalized sound systems, this unit shall have a cardioid
polar characteristic. The feedback threshold measured
in half-octave bands, shall be uniform from 110-5000
Hz. Above 5000 Hz, its response shall be peak free
and smoothly rolled off. The cancellation at the sides
shall be approximately 6 db and the cancellation at
the rear shall be 15to 20 db.The microphone shall have
an impedance of 150 ohms for connecting into micro-
phone inputs rated at 25 to 200 ohms. The microphone
output shall be:
150 ohms impedance
- 60.0 db
(0 db = 1 milliwattwith 10 microbars)
The microphone rating Gm (sensitivity) at 1000 Hz.
shall be
- 153.0 db
EIA Standard SE-105, August 1949
The microphone shall be provided with an adjustable
swivel adapter. The microphone swivel adapter shall
mount on a stand having a 518"-27 thread. The overall
dimensions shall be 6-5/16 inches (160.3 mm) in length
and 1-15/32 inches (37.3 mm) in diameter.
Copyright 1969, Shure Brothers Inc.
27A550 (LD)
(OVER)
U.S. Patents, 3,132,713 and 3,240,833
Printed
in U.S.A.

SPECIFICATIONS
Type:
Dynamic
Polar Pattern:
Cardioid (Unidirectional). Uniform with frequency,
symmetrical about axis.
Feedback Threshold:
Uniform from 110
Hz. to 5000 Hz. Above 5000 Hz., its
response shall be peak free and smoothly rolled off.
Microphone Rating Impedance:
150 ohms for connections into microphone inputs
rated at 25 to 200 ohms.
Output Level:
1000 Hz. response
Model ES50 (150 ohms impedance)
Open Circuit Voltage.
. . .. . . -81.5 db*(.085 mv)
Power Level.
... . . . . . .... .--60.0 db*
EIA Microphone Rating
Gm (Sensitivity)
.. . . ... .-153.0 dbn**
*O db = 1 volt per microbar
**0db = 1 milliwatt with 10 microbars
'**O db = EIA Standard SE-105, August 1949
Shock Mount:
Cartridge shock mounted for quiet operation.
Case:
Die-cast and "Armo-Dur".
Case Finish:
Non-reflecting gray paint.
Connector:
Professional three-pin male audio connector design-
ed to mate with Cannon XL series, Switchcraft A3
(Q.G.) series, or equivalent connector.
Dimensions:
See Figure
B.
Guarantee: This Shure product is guaranteed in normal
use to be free from electrical and mechanical defects
for a period of one year from the date of purchase.
Please retain proof of purchase date. This guarantee
includes all parts and labor.
Shipping Instructions: Carefully repack the unit and
return it prepaid to the factory. If outside the United
States, return the unit to your dealer or Authorized
Shure Service Center for repair. The unit will be re-
turned to you prepaid.
HALF OCTAVE FEEDBACK THRESHOLD
FIGURE A
OVERALL DIMENSIONS
FIGURE B
CABLE-PCUO ASSEMBLY
CARTRIDGE (NOT SUPPLIED)
POSITIVE PRESSURE PROWOES POSITIVE VOLTAGE AT PIN e .
INTERNAL CONNECTIONS
FIGURE C
Weight:
10% ounces (297 grams)
POLAR PATTERN
FIGURE D