Shuttle X50V2 PL User manual

.
53R-X50V23-2501
To placing on the desktop and carry your X50V2, do the following:
EVESA mounting to the wall
EPlacing on the desktop
180
04
05
06
Brightness controls
07
01 Webcam
02 Microphone
03 LCD Display (Touch enabled for X50V2 Plus only)
3.2.1.
EFront/Rear/Side View
Run the screen calibration program and correct 4 point locations
on screen with the panel.
Click Start / All Programs / eGalax Touch / Congure Utility
Select Tools tab and click 4 Points Calibration.
E How to use Touch Panel (For X50V2 Plus only)
When the 4 points calibration completed, press OK to continue.
E 4 Point Calibration (For X50V2 Plus only)
X50V2 Plus brings digital life for an easy touch experience.Experience
the ease of managing your digital life with a few touches or the use of
the stylus pen.Your touch functions like a mouse device and all you
need to interact with the X50V2 Plus.
Touch and hold the center of the target.
Repeat on four corners and the screen will adjust automatically.
ECleaning the touch screen
Follow these rules for cleaning the outside and handling your
screen on the computer :
Turn off the system and disconnect all cables.
Use a damp, or cleaning cloth, soft, lint-free cloth with gentle
water only and gently wipe the screen surface.
Do not spray liquid directly on the screen.
Touch = left-click on the mouse
Touch and hold = right-click on the mouse
Touch Hold OK
Click the application of short cut on desktop or Click start
buttom / All Programs /Control AP folder /Control AP
(Please refer the gure after starting)
EHow to use Control AP
Follow the steps (1~3) below to connect the AC adapter to the DCIN jack.
Press the Power Switch to turn on the system.
E Powering on the system
13 Stand / Handle
14 USB Ports
15 Power input
16
10 VGA Port
11 Printer Port
12 COM Ports
17
Stylus pen
Power Switch
DCIN
23
Audio Line-Out Port
24
MIC-In Port
25
LAN Port
20 4 in 1 Memory card reader
21 USB Ports
22
M
Place X50V2 on a at surface such as a table (Picture 1), and pull the stand
open until it angle of 30°. (Picture 2) When carry or move your X50V2, hold the
Top of the computer by its handle. (Picture 3)
Note: X50V2 can be mounted on a wall using a VESA compatible
100mm x 100mm wall/arm bracket.
X50V2 Plus / X50V2 PL. Quick Guide【English】
If you are mounting your X50V2 to the wall, remove the ”
Shuttle” Cover on the back of X50V2 rst.
Unscrew 4 screws of the stand mount and remove the stand.
Standard VESA to let user mount it on the wall easily.
Please refer to the user guide of the wall/arm mount kit you
bought to install it.
Stereo speaker
WiFi LED Kensington® Lock Port
Note: The product’s color and specication will depend upon the actually shipping product.
30
Hard disk drive LED
04
01
03
02
07
10
11
12
1513
17
16
20
21
22
23
24
25
05 06 14
Note: Descriptions of Control AP function:
1.Screen brightness control 2.Light Bar brightness control
3.Wireless ON/OFF 4.Web Camera ON/OFF
5.LCD/CRT switch 6.EXIT
01 02 03 04 05 06
E
Safety Information
Read the following precautions before setting up a Shuttle X50V2.
CAUTION
Do not walk on the power cord or allow anything to rest on it. The warranty does
not apply to the products that have been disassembled by users.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.