Sicor R5840X EOM WFG Operation instructions

SICUREZZA COMPAGNIE RIUNITE
1-0000S
R5840X (EOM)
WFG
Use and maintenance
instructions

0.2
SICUREZZA COMPAGNIE RIUNITE
EOM - WFG
Copyright by
SICOR S.p.A.
Via C. Pisacane 23/A - 20016 Pero (MI) Italy
Printed in Italy
Printed 05/10 - 2^ Edition 07/2012

SICUREZZA COMPAGNIE RIUNITE
EOM - WFG
0.3
SICUREZZA COMPAGNIE RIUNITE
These are the instructions for use of the R5840X hardhat, hereinafter called EOM, and the WFG
goggles.
These instructions were very carefully drawn up in accordance with UNI 10913:2001. Nonethe-
less, the editor cannot be held responsible for any errors and/or the possible consequences.
We would welcome any suggestions regarding the product or the manual and will implement them
if they would be a real improvement.
SICOR S.p.A. reserves the right to make any modications without prior notice to the product and
its accessories as well as their technical features.
Sincerely
SICOR S.p.A.

0.4
SICUREZZA COMPAGNIE RIUNITE
EOM - WFG

SICUREZZA COMPAGNIE RIUNITE
EOM - WFG
0.5
2
3
1
5
6
4
7
INTRODUCTION
CHAPTER 1
General regulations
CHAPTER 2
Use and adjustments
CHAPTER 3
Maintenance
CHAPTER 4
Accessories
CHAPTER 5
Technical data
CHAPTER 6
Warranty
CHAPTER 7
Declaration of conformity
CHAPTER INDEX

0.6
SICUREZZA COMPAGNIE RIUNITE
EOM - WFG

SICUREZZA COMPAGNIE RIUNITE
EOM - WFG
1.1
General regulations
GENERAL REGULATIONS
CONTENTS
1.1 - INTRODUCTION........................................................................1.2
1.1.a - How to consult the manual...............................................1.2
1.1.b - Component identication..................................................1.3
1.1.c - Reference standards........................................................1.4
1.1.d - Spare parts and accessories............................................1.4
1.1.e - Storage.............................................................................1.4
Chapter 1

EOM - WFG
1.2
SICUREZZA COMPAGNIE RIUNITE
General regulations
1.1 - INTRODUCTION
- This manual must be carefully read by the persons that will be wearing the hardhat
and the goggles and those that will be carrying out the maintenance operations.
- The hardhat and the goggles guarantee the performance for which they were de-
signed only if they are properly used and maintained according to the instructions in
this manual. Otherwise the protective features cannot be guaranteed.
- The warranties on these products shall become invalid if the warnings, precautions
and instructions contained in this manual are not followed.
- Should you have any doubts about the conditions of use or the maintenance proce-
dures after reading this manual, please do not hesitate to contact:
SICOR S.p.A.
Via C. Pisacane n. 23/a
20016 PERO (MI)
Tel. [phone]
Fax. [phone]
e-mail [email protected]
internet: http://www.sicor-sureco.it
1.1.a - How to consult the manual
- This manual must be kept for the entire lifetime of the PPD used
- This manual is divided into chapters covering different topics.
An index is given at the beginning of each chapter for easier consultation. The chapter
number is shown at the bottom left or right of each page and at the top of the page the
topic dealt with in the chapter.
- The following symbols are used in this manual to point out safety messages:
RISK TO PERSONS
Partial or total inobservance of the rules pointed out with this symbol may
cause serious risks to the health of the user of the hardhat and the gog-
gles.
IMPORTANT INFORMATION
This symbol indicates important communications for proper use or mainte-
nance of the hardhat and the goggles.

SICUREZZA COMPAGNIE RIUNITE
EOM - WFG
1.3
1-0064S
1
2a
2
3
4
5c
5b
5a
8a 8b
5f 5d
6e
6a
7
6c
6d
6b
1a
1b
5e
6f
6f
General regulations
1.1.b - Component identication
1 = Cap exterior
1.a = Ventilation system
1.b = Adapters
2 = Protective goggles (optional)
2.a = Cord
3 = PU cap interior
4 = Anti-shock straps
5 = Harness:
5.a = Front fasteners
5.b = Band
5.c = Suspension mesh
5.d = Size adjustment system
5.e = Rear fastener
5.f = Rear adjusters
6 = Retention system
6.a = Chin-strap
6.b = Anti-creep system
6.c = Anti-creep adjuster
6.d = Rectangular ring
6.e = Quick-release buckle
6.f = Anti-stretch strap
7 = Nape guard (optional)
8 = Comfort piece
8.a = Front comfort piece
8.b = Rear comfort piece

EOM - WFG
1.4
SICUREZZA COMPAGNIE RIUNITE
General regulations
1.1.c - Reference standards
Hardhat:
EN 397: 2001
EN 443: 1997 Points 5.6 - 5.7 - 5.8.1 - 5.8.3
EN 12492: 2003
1.1.d - Spare parts and accessories
IMPORTANT
Only original spare parts and accessories authorised and certied by the manufacturer
must be used and tted
Using non-original spare parts and unauthorised accessories will invalidate
the warranty conditions and relieve SICOR S.p.A. of all responsibility.
WARNING
- Never apply decals and/or identication labels less than 25 mm from the edges of the
cap; do not use paints, petrol or solvents to clean the hardhat.
Inobservance of these rules may reduce the levels of protection and/or the dielectric
properties.
- Do not modify or remove any of the constituent components of the hardhat.
1.1.e - Storage
IMPORTANT
• The hardhat must be stored in a clean, dry, dark place away from sources of heat and
at a temperature between +10°C (50°F) and +40°C (104°F).
• The hardhat and its accessories must be stored in the bag provided.
• Never leave the hardhat in a vehicle if not in its bag to prevent needless exposure to
the sun (UV rays).

SICUREZZA COMPAGNIE RIUNITE
2.1
EOM - WFG
Use and adjustments
USE AND ADJUSTMENTS
CONTENTS
2.1 - INTRODUCTION........................................................................2.2
2.2 - HEIGHT ADJUSTMENT ............................................................2.2
2.3 - CIRCUMFERENCE ADJUSTMENT ..........................................2.3
2.4 - RETENTION SYSTEM ADJUSTMENT .....................................2.4
2.4.a - First use............................................................................2.4
2.4.b - Regular use......................................................................2.4
2.5 - HARDHAT USE .........................................................................2.5
2.5.a - Ventilation system use......................................................2.5
Chapter 2

2.2
SICUREZZA COMPAGNIE RIUNITE
EOM - WFG
1-0004S
Use and adjustments
2.1 - INTRODUCTION
2.2 - HEIGHT ADJUSTMENT
- Any improper use not in compliance with the reference standards shall make the user
solely responsible for any personal harm and invalidate the warranty conditions.
- In order to provide adequate protection, this hardhat must be adjusted to the head size
of the user.
- The hardhat has been designed to absorb the energy of an impact by destroying or
partially damaging the cap and the harness; even if this damage may not immediately
be visible, any hardhat that has been subjected to strong impact must be replaced.
- For your own safety it is advisable to familiarise yourself with the adjustment systems
before using the hardhat. Make several adjustments and fasten and unfasten the
retention system several times so that these actions become instinctive.
Adjust the hardhat in height by changing
the depth of the suspension mesh as fol-
lows:
Release the rear tabs of the mesh fastened
with Velcro and slide them in the slots on
the harness.

SICUREZZA COMPAGNIE RIUNITE
2.3
EOM - WFG
1-0003S
1-0002S
2
Use and adjustments
2.3 - CIRCUMFERENCE ADJUSTMENT
IMPORTANT
The hardhat is supplied with the size adjust-
ment band fully extended.
For proper adjustment follow the sequence
described below.
- Put on the hardhat and then adjust the
size using the wheel (1).
- For optimal adjustment it is advisable to
push down on the hardhat with one hand
and then make the adjustment with the
other hand.
- The size adjustment system also acts
on the anti-creep system.
- Pull the two straps (2) that join the chin-
strap to the adjustment system only
during the rst adjustment.

2.4
SICUREZZA COMPAGNIE RIUNITE
EOM - WFG
1-0062S
3
1
1-0006S
3
1-0007S
1-0008S
Use and adjustments
2.4 - RETENTION SYSTEM ADJUSTMENT
2.4.a - First use
Chin-strap:
- Adjust in height as described in Chapter
2.2.
- Put on the hardhat.
- Adjust the size
(as described in Chapter 2.3)
- Fasten the buckle.
- Slide the adjustment strap (1) in the
adjustment crosspiece of the system
(2).
- Again pull the strap (1) so that the sys-
tem adjusts correctly.
- Should you be unable to achieve the
correct adjustment, act on the adjusters
(point 3) positioned on either side of the
chin-strap and lengthen or shorten the
strap as shown in the image.
2.4.b - Regular use
Chin-strap:
- Fasten the chin-strap with the buckle.
Size and anti-creep adjustment:
- Adjust as described in Chapter 2.3.

SICUREZZA COMPAGNIE RIUNITE
2.5
EOM - WFG
1-0009S
1
2
Use and adjustments
2.5 - HARDHAT USE
2.5.a - Ventilation system use
The hardhat ventilation system can be ad-
justed to prevent rainwater and re-extin-
guishing water from penetrating.
Operate the sliding lever on the top of the
hardhat with one hand.
Position 1 = Closed
Position 2 = Open
WARNING
Despite the steel spark protection mesh, we advise you to completely close the ventilation
system during res, near res or when there is a strong wind.

SICUREZZA COMPAGNIE RIUNITE
3.1
EOM - WFG
Maintenance
MAINTENANCE
CONTENTS
3.1 - HARDHAT DISASSEMBLY . .....................................................3.2
3.2 - HARDHAT ASSEMBLY . ...........................................................3.7
3.3 - HARDHAT CLEANING AND CARE. ....................................... 3.11
3.4 - INSPECTION PROCEDURE. .................................................. 3.11
3.5 - GOGGLES CLEANING. ..........................................................3.12
3.6 - HARDHAT LIFE. ......................................................................3.12
3.7 - GOGGLES LIFE. .....................................................................3.12
3.8 - DISPOSAL...............................................................................3.12
Chapter 3

3.2
SICUREZZA COMPAGNIE RIUNITE
EOM - WFG
1-0010S
3
1-0011S
4
1-0012S
Maintenance
3.1 - HARDHAT DISASSEMBLY
WARNING
It is recommended to read through each single paragraph before proceeding with the
disassembly operations.
To proceed with disassembly, place the hardhat upside down on an uncluttered surface in
order not to lose any components.
During the disassembly procedures, position all the parts removed in an orderly way.
- Pull the strap (1) out of the adjusters (2)
and out of the anti-creep system.
- Release the rear part (3) of the protective mesh (4).

SICUREZZA COMPAGNIE RIUNITE
3.3
EOM - WFG
1-0015S
1-0014S
5
1-0013S
55
6
6
Maintenance
- Release the two tabs (5) of the harness
(6).
- Release the rear of the harness (6) by
pulling upwards so that the clips are
released from the cap.

3.4
SICUREZZA COMPAGNIE RIUNITE
EOM - WFG
1-0019S
9
1-0018S
8
1-0016S
7
1-0017S
6
Maintenance
- Release the front part (7) of the harness (6) and pull it upwards so that the clips are
released from the cap, then remove the harness (6) from the hardhat.
- Remove the polyurethane cap interior (8).
- Release the retention system by pushing the fasteners (9) downward and remove the
harness with the retention system.