Siebert SX302 Series User manual

Serie SX302
Alphanumeric large size displays
with PROFINET IO RT interface
Operating instructions

BAL SX302 PFN 1.11 2/12
Table of contents
1Contact 3
2Legal note 4
3Safety precautions 5
Important information .........................................................................................................................................5
Safety .................................................................................................................................................................5
Intended use.......................................................................................................................................................5
Mounting and installation....................................................................................................................................5
Grounding...........................................................................................................................................................5
EMC measures...................................................................................................................................................6
Disposal..............................................................................................................................................................6
4Model designation 7
Model designation ..............................................................................................................................................7
Unit construction.................................................................................................................................................7
5Quick start 8
Step 1: Open project ..........................................................................................................................................8
Step 2: Switch to project view ............................................................................................................................8
Step 3: Install the GSDML file of the ad and add the display.............................................................................8
Step 4: Establish a connection to the display.....................................................................................................9
Step 5: Add sub-module to the display and define address range ....................................................................9
Step 6: Assign a PROFINET device name to the display................................................................................10
Step 7: Define text............................................................................................................................................11
Spep 8: Loading hardware configuration and program into the control...........................................................11
6Technical data 12
Fieldbus............................................................................................................................................................12
Power supply....................................................................................................................................................12
Housing colors..................................................................................................................................................12
Ambient conditions...........................................................................................................................................12

BAL SX302 PFN 1.11 3/12
1 Contact
www.siebert-group.com
GERMANY
Siebert Industrieelektronik GmbH
Siebertstrasse, D-66571 Eppelborn
P.O. Box 11 30, D-66565 Eppelborn
Phone [phone], Fax [phone]
email: [e-mail]
AUSTRIA
Siebert Österreich GmbH
Simmeringer Hauptstrasse 24, A-1110 Wien
Phone [phone], Fax [phone]
email: [e-mail]
FRANCE
Siebert France Sarl
4 rue de l’Abbé Louis Verdet, F-57200 Sarreguemines
P.O. Box 90 334, F-57203 Sarreguemines Cédex
Phone [phone], Fax [phone]
email: [e-mail]
ITALY
Siebert Italia Srl
Via Galileo Galilei 2A, I-39100 Bolzano (BZ)
Phone [phone] Fax [phone]
email [e-mail]
THE NETHERLANDS
Siebert Nederland B.V.
Jadedreef 26, NL-7828 BH Emmen
Phone [phone], Fax [phone]
email: [e-mail]
SWITZERALND
Siebert AG
Bützbergstrasse 2, CH-4912 Aarwangen
Phone [phone], Fax [phone]
email: [e-mail]

BAL SX302 PFN 1.11 4/12
2 Legal note
© Siebert Industrieelektronik GmbH
This operation manual has been prepared with the utmost care. However, we do not accept any
liability for possible errors. We always appreciate your suggestions for improvement, corrections,
comments and proposals. Please contact us: [e-mail]
Siebert®, LRD®and XC-Board®are registered trademarks of Siebert Industrieelektronik GmbH. All
other product names mentioned herein may be trademarks or registered trademarks of their respective
owners.
We reserve the right to make alterations to the technical data and delivery options without notice. - All
rights reserved, including the rights of translation. No part of this document may in any form or by any
means (print, photocopy, microfilm or any other process) be reproduced or by using electronic
systems be processed, copied or distributed without our written permission.

BAL SX302 PFN 1.11 5/12
3 Safety precautions
Important information
Read these operating instructions before starting the unit. They provide you with important information
on the use, safety and maintenance of the units. This helps you to protect yourself and prevent
damage to the unit.
Information intended to help you to avoid death, bodily harm or considerable damage to
property is highlighted by the warning triangle shown here; it is imperative that this
information be properly heeded.
The operating instructions are intended for trained professional electricians familiar with the safety
standards of electrical technology and industrial electronics.
Store these operating instructions in an appropriate place.
The manufacturer is not liable if the information in these operating instructions is not complied with.
Safety
Components inside the units are energized with electricity during operation. For this reason,
mounting and maintenance work may only be performed by professionally-trained personnel
while observing the corresponding safety regulations.
The repair and replacement of components and modules may only be carried out by the manufacturer
for safety reasons and due to the required compliance with the documented unit properties.
The units do not have a power switch. They are operative as soon as the operating voltage is applied.
Intended use
The units are intended for use in industrial environments. They may only be operated within the limit
values stipulated by the technical data.
When configuring, installing, maintaining and testing the units, the safety and accident-prevention
regulations relevant to use in each individual case must be complied with.
Trouble-free, safe operation of the units requires proper transport, storage, installation, mounting and
careful operation and maintenance of the units.
Mounting and installation
The attachment options for the units were conceived in such a way as to ensure safe, reliable
mounting.
The user must ensure that the attachment hardware, the unit carrier and the anchoring at the
unit carrier are sufficient to securely support the unit under the given surrounding conditions.
The units are to be mounted in such a way that they can be opened up while mounted. Sufficient
space for the cables must be available in the unit near the cable entries.
Sufficient space is to be kept clear around the units to ensure air circulation and to prevent the build-
up of heat resulting from use. The relevant information must be heeded in the case of units ventilated
by other means.
When the housing fasteners are opened, the front frame of the housing hinges out upward or
downward (depending on the unit version) automatically.
Grounding
All devices are equipped with a metal housing. They comply with safety class I and require a
protective earth connection. The connecting cable for the operating voltage must contain a protective
earth wire of a sufficient cross section (DIN VDE 0106 part 1, DIN VDE 0411 part 1).

BAL SX302 PFN 1.11 6/12
EMC measures
The devices comply with the current EU Directive (EMC Directive) and provide the required
interference immunity. Observe the following when connecting the operating voltage and data cables:
Use shielded data cables.
The data and operating voltage cables must be laid separately. They may not be laid together with
heavy-current cables or other interference-producing cables.
The cable thickness must be properly assessed (DIN VDE 0100 Part 540).
The cable lengths inside the units are to be kept as short as possible to prevent interference. This
applies especially to unshielded operating voltage cables. Shielded cables are also to be kept short
due to any interference which might be emitted by the shielding.
Neither excessively long cables nor cable loops may be placed inside the units.
The connection of the cable shielding to the functional ground (PE) must be as short and low-
impedance as possible. It should be made directly to the mounting plate over a large area with a
conductive clip:
①mounting plate
②conductive clamp
③data lines
④cable shielding
The cable shielding is to be connected at both cable ends. If equipotential bonding currents are
expected due to the cable arrangement, electrical isolation is to be performed on one side. In this
case, capacitive connection (approx. 0.1μF/600 V AC) of the shielding on the isolated side must occur.
Disposal
Units or unit parts which are no longer needed are to be disposed of in accordance with the
regulations in effect in your country.

BAL SX302 PFN 1.11 7/12
4 Model designation
Model designation
This manual applies to units with the following model designation (x = the 'x's in the model designation
indicate the size and design of the units):
SX302-xx/xx/xx-xxx/xx-N0
Unit construction
The following figure shows model type SX302-06/10/xx-xxx/xx-xx as example for the other model
types. The front frame of the housing is locked with quick-action releases. When opening the unit the
front frame hinges downward.
The following figure shows the unit when open.
Central
Processing
Unit
Power supply
unit
Display modules
Units with double-sided display show the same information on the front and on the rear side.

BAL SX302 PFN 1.11 8/12
5 Quick start
Quick-Start
The display is put into operation with the following steps. The display then shows the values sent via
PROFINET.
The screenshots were created with the following hardware and software. For other engineering
frameworks, the descriptions shown in this user's guide may differ from the screen display on your
device.
Display
SX302-08/10/0R-101/0A-N0
Engineering-Framework
Siemens TIA Portal V17, Update 4
SPS
Siemens S7-1214C DC/DC/Rly, V4.5, 6ES7 214-1HG40-0XB0
Operating system
Microsoft Windows 10 Professional, 64 Bit
The quick start describes the parameterization of the display. Operation of the TIA Portal is required.
The devices are delivered without PROFINET name.
Schritt
Step 1: Open project
Open your project in the Engineering-Framework.
Step 2: Switch to project view
Switch to project view.
Step 3: Install the GSDML file of the ad and add the display
Install the GSDML file of the display. You find the file on the supplied data carrier or at www.siebert-
group.com. After installation, the display is listed in the hardware catalog.
Add the module 'SX302' from the catalog to the 'Devices & networks/Network view'.

BAL SX302 PFN 1.11 9/12
Step 4: Establish a connection to the display
Assign the display to the desired control in the network view. Then the PROFINET connection is
shown.
Step 5: Add sub-module to the display and define address range
Add the module 'Simplified page module' from the hardware catalog to the device overview.
This specifies that the display expects the values to be shown in ASCII String format. The module
occupies 32 bytes (in this example the addresses 64 to 95).
You can change the name given by the TIA Portal.
In the Module parameters section you can set the initialization parameters for brightness and text
alignment.

BAL SX302 PFN 1.11 10/12
Step 6: Assign a PROFINET device name to the display
Now assign the IP address and device name to the display. To do this, call up the context menu of the
Siebert display in the Device view and click on 'Assign device name'.
After the data is transferred successfully to the display, the configuration is displayed as follows in the
engineering tool.

BAL SX302 PFN 1.11 11/12
Step 7: Define text
To send a value to the display, you can for example create a function chart with 'MOVE' instructions.
In the following screenshot the text 'Siebert' is sent. This requires two 'MOVE' function blocks.
Spep 8: Loading hardware configuration and program into the control.
After switching on the display the start text 'SX302' is shown.
As soon as the configuration and the program function block are loaded into the control, the control
connects to the display via PROFINET and the display shows the text 'Siebert'.
The data traffic via PROFINET is indicated with status LEDs on both RJ45 sockets.
The meaning is the same for both ports.
LED green
LED yellow
Meaning
off
off
no power supply
no network connection
on
ons
network connection exists
on
flashing
initialization phase
application relation is set up
on
on
application relation is established
If the connection can not be established or faults occur during operation the display shown the error
message ''. Possible causes are IP problems due to incorrect network parameters, multiple
device names, command of undefined properties or other fieldbus errors.

BAL SX302 PFN 1.11 12/12
Technische
6 Technical data
Fieldbus
Interface PROFINET IO RT, conformance class CC-B
MAC address The MAC address for the PROFINET coupling is on the top side of the
device.
Integrated switch PROFINET IO IRT, conformance class CC-C
Power supply
The screw terminals for the power supply are located on the power supply unit in the lower part of the
housing. They have the following designations:
Devices for power supply 115 V AC or 230 V AC L, N, and PE
Devices for power supply 24 V DC +, - and PE
Housing colors
Housing front frame RAL 5002 ultramarine blue
Housing lower part RAL 7035 light gray
Ambient conditions
Operating temperature 0…55 °C, with heating -20…55 °C
Storage temperature -30…85 °C
Relative humidity max. 95% (non-condensing)