Siebert Series S102 User manual

Pos: 2/ Siebert/Bedie nungsanleitungen/ Serie S102/SX102/Ti telseiten/S102 Titels eite PFN RT @ 3\mod _14851629553 44_48.docx @ 26784 @ @ 1
Series S102
Numeric displays in build-in housings
with Profinet IO RT-interface
Operating instructions
Pos: 3/ Siebert/Seitenum bruch @ 0\mod_13141945 53878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 2/24
Pos: 4/ Siebert/Bedie nungsanleitungen/ Gerätebeschreib ung Grossanzeigen all eS erien/Kontakt @ 1 \mod_1339668 951540_48.docx @ 43 23@ 1@ 1
1 Contact
www.siebert-group.com
GERMANY
Siebert Industrieelektronik GmbH
Siebertstrasse, D-66571 Eppelborn
P.O. Box 11 30, D-66565 Eppelborn
Phone [phone], Fax [phone]
email: [e-mail]
AUSTRIA
Siebert Österreich GmbH
Mooslackengasse 17. A-1190 Wien
Phone [phone], Fax [phone]
email: [e-mail]
FRANCE
Siebert France Sarl
4 rue de l’Abbé Louis Verdet, F-57200 Sarreguemines
P.O. Box 90 334, F-57203 Sarreguemines Cédex
Phone [phone], Fax [phone]
email: [e-mail]
ITALY
Siebert Italia Srl
Via Galileo Galilei 2A, I-39100 Bolzano (BZ)
Phone [phone] Fax [phone]
email [e-mail]
THE NETHERLANDS
Siebert Nederland B.V.
Jadedreef 26, NL-7828 BH Emmen
Phone [phone], Fax [phone]
email: [e-mail]
SWITZERALND
Siebert AG
Bützbergstrasse 2, P.O. Box 91, CH-4912 Aarwangen
Phone [phone], Fax [phone]
email: [e-mail]
Pos: 5/ Siebert/Seitenum bruch @ 0\mod_13141945 53878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 3/24
Pos: 6/ Siebert/Bedie nungsanleitungen/ Gerätebeschreib ung Grossanzeigen all eS erien/Rechtlic herHi nweis @ 1\mod_1 339668878995_4 8.docx @ 4317 @ 1 @ 1
2 Legal note
© Siebert Industrieelektronik GmbH
This operation manual has been prepared with the utmost care. However, we do not accept any
liability for possible errors. We always appreciate your suggestions for improvement, corrections,
comments and proposals. Please contact us: [e-mail]
Siebert®, LRD®and XC-Board®are registered trademarks of Siebert Industrieelektronik GmbH. All
other product names mentioned herein may be trademarks or registered trademarks of their respective
owners.
We reserve the right to make alterations to the technical data and delivery options without notice. - All
rights reserved, including the rights of translation. No part of this document may in any form or by any
means (print, photocopy, microfilm or any other process) be reproduced or by using electronic
systems be processed, copied or distributed without our written permission.
Pos: 7/ Siebert/Seitenum bruch @ 0\mod_13141945 53878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 4/24
Pos: 8/ Siebert/Bedienungs anleitungen/Modul Inh altsverzeichnis @ 1\mod_1 352981287156_48. docx@ 51 55@ @ 1
Table of contents
1Contact 2
2Legal note 3
3Safety precautions 6
Important information .........................................................................................................................................6
Safety .................................................................................................................................................................6
Intended use.......................................................................................................................................................6
Mounting and installation....................................................................................................................................6
Grounding...........................................................................................................................................................6
EMC measures...................................................................................................................................................6
Disposal..............................................................................................................................................................7
4Model designation 8
Model designation ..............................................................................................................................................8
5Quick start for numerical operation mode (INT32 format) 8
Step 1: Open project ..........................................................................................................................................8
Step 2: Switch to project view ............................................................................................................................8
Step 3: Install the GSDML file of the ad and add the display.............................................................................9
Step 4: Establish a connection to the display.....................................................................................................9
Step 5: Add sub-modul to the display and define address range ....................................................................10
Step 6: Assign a PROFINET device name to the display................................................................................11
Step 7: Download configuration in the controller..............................................................................................11
Step 8: Transmit data to the display.................................................................................................................12
6Quick start for alphanumeric operation mode (ASCII format) 13
Step 1 to 4: See quick start for numeric operation mode (INT32 format) ........................................................13
Step5: Add sub-modul to the display and define address range .....................................................................13
Step 6 and 7: See quick start for numeric operation mode (INT32-Format)....................................................13
Step 8: Transmit values and texts to the display..............................................................................................14
7Messages on the display 15
8Further settings 16
9Setting the display settings during initialization (numeric operation mode only) 17
Decimal points Decimal Dots (property number 1) ..........................................................................................17
Offset, scale factor (multiplier), and divisor (property numbers 2, 3 and 12) ...................................................17
Threshold values Range (property numbers 4 und 5) .....................................................................................17
Flags (property number 6)................................................................................................................................17
Attributes for flashing and blinking (property numbers 7 and 9) ......................................................................18
Format (property numbers 10 and 11) .............................................................................................................18
10 Flashing modes and display attributes 19
11 Flags 20

BAL S102 PFN RT 1.00 5/24
12 Setting the display mode in normal operation 21
Setting the basic brightness (luminousity of the LEDs)....................................................................................21
Setting of the display modes............................................................................................................................22
13 Technical data 23
Display..............................................................................................................................................................23
Field bus...........................................................................................................................................................23
Power supply....................................................................................................................................................23
Dimensions and weights ..................................................................................................................................23
Housings...........................................................................................................................................................23
Ambient conditions...........................................................................................................................................23
=== Ende der Liste für Te xtmarke Inhalt1 ===
Pos: 10 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 6/24
Pos: 11 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Sicherheitshinw eise/S102 Sicherh eitshinweise Gross anzeigen PFN RT @ 4\m od_14852724355 25_48.docx @ 27156 @ 1 2222222 @ 1
3 Safety precautions
Important information
Read these operating instructions before starting the unit. They provide you with important information
on the use, safety and maintenance of the units. This helps you to protect yourself and prevent
damage to the unit.
Information intended to help you to avoid death, bodily harm or considerable damage to
property is highlighted by the warning triangle shown here; it is imperative that this
information be properly heeded.
The operating instructions are intended for trained professional electricians familiar with the safety
standards of electrical technology and industrial electronics.
Store these operating instructions in an appropriate place.
The manufacturer is not liable if the information in these operating instructions is not complied with.
Safety
Installation work may only be carried out by qualified personnel in compliance with the relevant safety
egulations. Inside the housing there are no parts that must be accessible to the user during installation
or operation of the device. The housing must never be opened.
The repair and replacement of components and modules may only be carried out by the manufacturer
for safety reasons and due to the required compliance with the documented unit properties. .
Intended use
The units are intended for use in industrial environments. They may only be operated within the limit
values stipulated by the technical data.
When configuring, installing, maintaining and testing the units, the safety and accident-prevention
regulations relevant to use in each individual case must be complied with.
Trouble-free, safe operation of the units requires proper transport, storage, installation, mounting and
careful operation and maintenance of the units.
Mounting and installation
The attachment options for the units were conceived in such a way as to ensure safe, reliable
mounting.
The user must ensure that the attachment hardware, the unit carrier and the anchoring at the
unit carrier are sufficient to securely support the unit under the given surrounding conditions.
Sufficient space is to be kept clear around the units to ensure air circulation and to prevent the build-
up of heat resulting from use.
Grounding
All devices are equipped with a plastic housing and are operated with 24 V DV. They have a flat plug,
which is connected to the shield of the PROFINET sockets and the metal back wall. A connection with
the protective conductor is recommended.
EMC measures
The devices comply with the current EU Directive (EMC Directive) and provide the required
interference immunity. Observe the following when connecting the operating voltage and data cables:
Use shielded data cables.
The data and operating voltage cables must be laid separately. They may not be laid together with
heavy-current cables or other interference-producing cables.

BAL S102 PFN RT 1.00 7/24
Disposal
Units or unit parts which are no longer needed are to be disposed of in accordance with the
regulations in effect in your country.
Pos: 12 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 8/24
Pos: 13 /Siebert/Bedienu ngsanleitungen/Seri eS1 02/SX102/Geräteb eschreibung / Geltungsbereich/ Geltungsbereich/Ü BSG eltungsbereich @ 4\ mod_1485273939553_4 8.docx@ 2 7170 @ 1@ 1
Geltungsbereich
4 Model designation
Pos: 14 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Gerätebeschrei bung/ Geltungsbereich/G eltungsbereich/S 102 Geltungsbereich PFN RT @ 4\ mod_148516403277 5_48.docx @ 26800 @ 2@ 1
Geltungsbereich
Model designation
This manual applies to units with the following model designation: (x = the 'x's in the model
designation indicate the size and design of the units).
S102-xx/14/0x-00x/0B-N0
Pos: 15 /Si ebert/Bedie nungsanleitu ngen/Seri eS 102/SX1 02/Quick- Start für numerischeB etriebsart (INT 32-F ormat)/ÜBS Quick-St artf ür num erische B etriebsart (INT 32-For mat) @ 4 \mod_1485 16527372 6_48.docx @ 26814 @ 1 @ 1
5 Quick start for numerical operation mode (INT32 format)
Pos: 16 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für num erische Betriebsart (INT 32-Format)/S1 02 Quick-Start für nu merische Betriebsart (INT3 2-Format) PFN RT @ 4\ mod_148516498 8306_48.docx @ 268 07@ @ 1
Quick-Start
The display is put into operation with the following steps. The display then shows the values sent via
PROFINET.
The screenshots were created with the following hardware and software. For other engineering
frameworks, the descriptions shown in this user's guide may differ from the screen display on your
device.
Display
S102-04/14/0R-000/0B-N0
Engineering-Framework
Siemens TIA Portal V13, Service Pack1 , Update 9
SPS
Siemens S7-1214C
Operating system
Microsoft Windows 7 Professional, 64 Bit, english
The quick start describes the parameterization of the display. Operation of the TIA Portal is required.
The devices are delivered with the PROFINET name 'siebert-display'.
Pos: 17 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für num erische Betriebsart (INT 32-Format)/S1 02 Schritt 1: Projet öffnen PFN RT @ 4\mod_148516612 0660_48.docx @ 2682 1@ 2 @ 1
Schritt
Step 1: Open project
Open your project in the Engineering-Framework.
Pos: 18 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für num erische Betriebsart (INT 32-Format)/S1 02 Schritt 2: Zur Projekta nsicht wechseln PFN RT @ 4\ mod_14851662 63609_48.docx @ 2 6828@ 2@ 1
Step 2: Switch to project view
During this time the display displays 'E4' or 'P7'. This means that the display is waiting for connection.
Other messages may also be displayed at short notice.
Switch to project view..
Pos: 19 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-St artf ür numerische Betrie bsart (INT32-For mat)/S102 Schritt 3: GSDML-D atei der Anzeige ins tallieren und Anzeige hi nzufügen PFN RT @ 4\ mod_148516678 4571_48.docx @ 26 841 @ 2@ 1

BAL S102 PFN RT 1.00 9/24
Step 3: Install the GSDML file of the ad and add the display
Install the GSDML file of the display. You find the file on the supplied data carrier or at www.siebert-
group.com. After installation, the display is listed in the hardware catalog. Add the module 'siebert-
display' to 'Devices & Networks/Network view'.
Pos: 20 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für num erische Betriebsart (INT 32-Format)/S1 02 Schritt 4: Verbindung zur A nzeige herstellen PFN R T@ 4\mod_148516763 8878_48.docx @ 2685 4 @2 @ 1
Step 4: Establish a connection to the display
Assign the display to the desired control in the network view. Then the PROFINET connection is
shown.
Pos: 21 /Si ebert/Bedie nungsanleitu ngen/Seri eS 102/SX1 02/Quick- Start für numerischeB etriebsart (INT 32-Format)/S102 Schritt 5: S ub-Modul der Anz eige hinzufügen und Adress bereich definiere nPF NRT @4\ mod_14851684 79408_48.docx @ 268 61@ 2@ 1

BAL S102 PFN RT 1.00 10/24
Step 5: Add sub-modul to the display and define address range
Add the module 'Numerical Value' from the hardware catalog to the device overwiew.
This specifies that the display expects the values to be shown in INT32 format. The module occupies
4 bytes (in this example the addresses 64 to 67).
You can change the name given by the TIA Portal.
Pos: 22 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für num erische Betriebsart (INT 32-Format)/S1 02 Schritt 6: Der Anzeig eein enPR OFINET-G erätenamen zuweisen PFN R T @ 4\mod_14 85169208994_48.d ocx @ 26868 @ 2 @ 1

BAL S102 PFN RT 1.00 11/24
Step 6: Assign a PROFINET device name to the display
Now the IP address and the device name are assigned to the display.
After the data has been successfully transferred to the display, the configuration is displayed as
follows in the engineering tool. The display still shows 'P7'.
Pos: 23 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für num erische Betriebsart (INT 32-Format)/S1 02 Schritt 7: Konfiguratio ni n die Steuerung lade nPFN RT @4\ mod_14851743 74379_48.docx @ 269 22@ 2@ 1
Step 7: Download configuration in the controller
After the control can connect via PROFINET with the display. As soon as the connection is
established the display shown the '0'. The display is now programmed to receive numerical values in
INT32 format.
Pos: 24 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für num erische Betriebsart (INT 32-Format)/S1 02 Schritt 8: Werte zur Anzeige se nden PFN RT @ 4\m od_148517171 6771_48.docx @ 2687 5@ 2 @ 1

BAL S102 PFN RT 1.00 12/24
Step 8: Transmit data to the display
To transmit a value to the display you can, for example, create a function chart with the instruction
'MOVE'. In the following screenshot the number '1234' is transmitted.
Pos: 25 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 13/24
Pos: 26 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für alp hanumerische Betri ebsart( ASCII-Form at)/ÜBS Quick-Start f üral phanumerische B etriebsart (ASCII-For mat) @ 4\mod_1485 172288413_48. docx@ 26882 @ 1@ 1
6 Quick start for alphanumeric operation mode (ASCII format)
Pos: 27 /Si ebert/Bedie nungsanleitu ngen/Seri eS 102/SX1 02/Quick- Start für alphanumerische Betri ebsart (ASC II-Format)/ S102 Quic k-Start f ür alphan umerische B etriebsart ( ASCII-For mat) PFN RT @ 4 \mod_1 48517241121 6_48.docx @ 26889 @ @ 1
If the display receives data in ASCII format it can display also characters and special characters which
can be displayed by seven segments besides the digits.
Received characters which can not be displayed with seven segments are displayed as .
Pos: 28 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für alp hanumerische Betri ebsart( ASCII-Form at)/S102 Schritte 1 bis 4: sieh eQ uick-Start für numeri sche Betriebsart (INT 32-Format) PFN RT @ 4\mod_1485173309645 _48.docx @ 26895 @ 2 @ 1
Step 1 to 4: See quick start for numeric operation mode (INT32 format)
Step 1: Open project
Step 2: Switch to project view
Step 3: Install the GSDML file of the ad and add the display
Step 4: Establish a connection to the display
Pos: 29 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für alp hanumerische Betri ebsart( ASCII-Form at)/S102 Schritt 5: Sub-Mo dul der Anzeige hinzufüg en und Adressberei ch definieren PFN RT @ 4 \mod_148517356 6639_48.docx @ 2690 2@ 2 @ 1
Step5: Add sub-modul to the display and define address range
Add the module 'Text and attribute' from the hardware catalog to the device overwiew. The two sub-
modules 'Text (ASCII)' and 'Attribute' are added automatically.
This specifies that the display occupies two blocks in the output data area: 20 bytes for the text and 2
bytes for the attributes.
Pos: 30 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für alp hanumerische Betri ebsart( ASCII-Form at)/S102 Schritte 6 und 7: si ehe Quick-Start für numerisc he Betriebsart (INT 32-Format) PFN RT @ 4\mod_1485173933179 _48.docx @ 26909 @ 2 @ 1
Step 6 and 7: See quick start for numeric operation mode (INT32-Format)
Step 6: Assign a PROFINET device name to the display
Step 7: Download the configuration to the controller
Pos: 31 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Quick-Start für alp hanumerische Betri ebsart( ASCII-Form at)/S102 Schritt 8: Werte od erTe xte zur Anzeige se ndenPFN RT@ 4\mod_148517475107 5_48.docx @ 26929 @ 2 @ 1
Schritt 8:

BAL S102 PFN RT 1.00 14/24
Step 8: Transmit values and texts to the display
Since the display has two address areas in this operating mode, two function blocks (in the example
'Network 1' and 'Network 2') must also be defined.
In 'Network 1' a function plan is defined with the 'MOVE' statement. In the example, the output area
begins with AD64. The following screenshot uses the string 'abcd'.
In 'Network 2', a further function plan is defined with the 'MOVE' statement. With this, the attributes are
controlled. Attributes define the display type. In this example, the value '16 # 0033 'is used to define
fast flashing.
The string sent to the display can be up to 20 bytes long. The displayed bytes are dependent on the
scope of the display. The non-representable sequence bytes are ignored.
The attributes are binary coded. Its structure is described in the chapter 'Attributes'.
Pos: 32 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 15/24
Pos: 33 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Meldungen der Anz eige/ÜBS Meldungen d erA nzeige @ 4\mod _1485175421892 _48.docx @ 26936 @ 1 @ 1
Meldungen
7 Messages on the display
Pos: 34 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Meldungen der Anz eige/S102 Meldung end er Anzeige PFN RT @ 4 \mod_148517557 2236_48.docx @ 2694 3 @ @1
The data traffic via PROFINET is indicated with status LEDs on both RJ45 sockets.
The meaning is the same for both ports.
LED green
LED yellow
Meaning
off
off
no power supply
no network connection
on
ons
network connection exists
on
flashing
initialization phase
application relation is set up
on
on
application relation is established
During the initialization phase, the display indicates certain operating conditions:
E4
Invalid subnet mask
P1…P4
PROFINET is initialized
E5
Invalid station name
P5
Device is configured
E7
Errror during connection
P7
Display waits for data
E6
Internal error
Once the PROFINET connection has been established, the following messages can be displayed:
4-digit display
6-digit display


Until the first time user data is received, the display shows a
frame on its display alternating with the above status
messages.


The "PROFINET flashing" diagnostic function, which can be
called from the engineering tool, is signaled by three
horizontal lines at each position.


Underflow: The value sent to the display can not be
displayed on the display. For example, the value '-1500' can
not be displayed on a four-digit device.


Overflow: The value sent to the display can not be displayed
on the display. For example, the value '-26550' can not be
displayed on a four-digit device.
Pos: 35 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 16/24
Pos: 36 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Weitere Einstellunge n/ÜBS Weitere Einst ellungen @ 4\mod _1485177153460 _48.docx @ 26955 @ 1 @ 1
8 Further settings
Pos: 37 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Weitere Einstellunge n/S102 Weitere Eins tellungen PFN RT @ 4 \mod_1485177 224794_48.docx @ 26 962 @ @1
With the previous steps, the display shows the sent values with their default settings (factory settings).
In the numeric mode (INT32 format) these settings can be changed by changing the initialization
values. These are transferred once to the display during connection setup via PROFINET.
The following setting options are available by changing the initialization values, see chapter setting the
display settings during initialization (numeric operation mode only):
Number and position of the decimal points
Offset, scale factor (multiplier), and divisor for the conversion formula of the numerical value
Upper and lower thresholds for automatically changing the display mode
Luminosity of the LEDs
Blinking in different modes when thresholds are exceeded or fallen below
Lowering or raising the LED brightness when exceeding or falling below the thresholds
Position of the displayed value
Number of leading zeros
In addition, the S102 series offers the possibility - in both operation modes (INT32 and ASCII format) -
to change all previously mentioned settings as well as the setting of the basic brightness (LED
brightness) in 16 steps during normal operation (see chapter setting of the display mode in normal
operation mode).
Pos: 38 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 17/24
Pos: 39 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Einstellung der Darst ellungsart bei der Initialisi erung (nur numerisch e Betriebsart)/ÜB SEi nstellung der Darst ellungsart bei der Initialisier ung( nur numerisch e Betriebsart) @ 4\ mod_14851793074 03_48.docx @ 269 68 @1 @ 1
9 Setting the display settings during initialization (numeric operation mode only)
Pos: 40 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Einstellung der Darst ellungsart bei der Initialisi erung (nur numerisc he Betriebsart)/Einl eitungssatz PFN RT @4\m od_1485179498648 _48.docx @ 26975 @ @ 1
Initialization parameters are loaded once to the display. They can not be changed during operation.
Pos: 41 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Einstellung der Darst ellungsart bei der Initialisi erung (nur numerisc he Betriebsart)/Dezi malpunkte/S1 02Dezi malpunkte Deci mal Dots (property nu mber 1)P FN RT @ 4\mod_ 1485179820250_4 8.docx @ 26988 @ 2 @ 1
Decimal Dots
Decimal points
Decimal Dots (property number 1)
The number and position of the decimal points can be defined with the help of a bit mask. For
example, multiple decimal points can be used to display a date or codes.
A set bit corresponds with a set decimal point.
The least significant bit corresponds to the decimal point of the least significant digit. If, for example,
the number '1234' is to be displayed with a decimal point between the 100th and the 10th digit, the bit
mask must be set to the value '0x04' and '12 .34 'appears on the display.
Pos: 42 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Einstellung der Darst ellungsart bei der Initialisi erung (nur numerisc he Betriebsart)/Offse t, Skalenfaktor (Multi plikator) und Divisor/ S102 Offset, Skalenfac tor (Multiplikator) un dDi visor (property nu mbers 2, 3 und 12) PFN RT @ 4\ mod_148518050 5571_48.docx @ 2 6995@ 2@ 1
Offset, scale factor (multiplier), and divisor (property numbers 2, 3 and 12)
The formula that can be stored in the display allows you to display values in other units, such as
degrees Fahrenheit in degrees Celsius, kilograms in tons, miles in kilometers, or adding an offset.
This initialization parameter consists of the values offset, scale factor (multiplier) and divisor.
Meaning
Property number
Data typep
Default value
Offset
2
SINT32
0
Scale Factor
3
SINT16
1
Divisor
12
UINT16 (unsigned)
1
The calculation is based on the following linear function:
Displayed value = offset + scale factor (multiplier) / divisor * sent value
As a scale factor, integers are possible. Other factors can be formed by a combination of 'ScaleFactor'
and 'Divisor'. For example, a multiplication with '13, 42 'can be generated by the scale factor' 1342
'and divisor' 100 '.
Pos: 43 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Einstellung der Darst ellungsart bei der Initialisi erung (nur numerisc he Betriebsart)/Sc hwellenwerte/S1 02S chwellenwerte Ra nge( property numb ers4 un d 5)PFN RT @ 4\mod_14851 82934040_48.doc x @ 27026 @ 2 @ 1
Threshold values
Range (property numbers 4 und 5)
This initialization value defines the upper and lower thresholds at which the display automatically
changes its display attribute.
Meaning
Property number
Data type
Default values
Upper bound
4
SINT32
-2147483648
Lower bound
5
SINT32
-2147483648
No threshold values are defined in the delivery state. The default value -2147483648 (hex:
0x80000000) commands this.
If a value is received outside the defined thresholds, the display automatically changes from 'standard'
to 'out of range'. As soon as a value is received within the defined limits, the display returns to
standard.
Example: For a temperature value display, the display should change its display mode, both when the
temperature falls below 0 degrees Celcius and when it exceeds 100 degrees Celcius. For this, the
values Upper bound = 100 and Lower bound = 0 must be entered.
Pos: 44 /Siebert/Bedienu ngsanleitungen/Seri eS1 02/SX102/Einstellung der Darst ellungsart bei der Initialisieru ng(n urnu merische Betriebsart)/Fl ags( property number 6)/S102 Flags (prop erty number 6) PFN RT@ 4 \mod_1485183 888722_48.docx @ 27039 @ 2 @ 1
Flags (propüerty
Flags (property number 6)
In this initialization value (type INT16), display properties are set.
See chapter Flags.
Pos: 45 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Einstellung der Darst ellungsart bei der Initialisi erung (nur numerisc he Betriebsart)/At tribute für Blinken und Bli nkmodus/S102 Attribut e für Blinken und Blinkm odus (property numb ers 7u nd 9) PFN RT @ 4\m od_148518407 5448_48.docx @ 2704 6@ 2 @ 1

BAL S102 PFN RT 1.00 18/24
Attributes for flashing and blinking (property numbers 7 and 9)
With these initialization values, the flashing modes for the standard display and the 'out of range'
display can be defined.
See chapter .Flashing modes.
Pos: 46 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Einstellung der Darst ellungsart bei der Initialisi erung (nur numerisc he Betriebsart)/For mat/S102 Format (pro perty numbers 10 un d11) PFN RT @4\ mod_148518 4357493_48.docx @ 2 7053@ 2@ 1
F
Format (property numbers 10 and 11)
These two initialization parameters define the alignment of the displayed values and the number of
leading zeros.
Meaning
Property number
Data type
Default values
Minimum number of digits
10
UINT8
1
Minimum width
11
UINT8
30
The minimum number of digits displayed is defined as 'Minimum number of digits'. If the value to be
displayed has less digits than 'Minimum number of digits', the display is filled with zeros on the left
side.
Example: For a six-digit display the 'Minimum number of digits' is set to 6. If the number '1234' is sent
to the display, the display shows '001234'.
'Minimum Width' defines the minimum number of digits used for display. If the number representation
contains less characters (including the sign), the space is filled with blanks on the left side.
Example: To display a number on the left-hand side, set the parameter 'Minimum Width' to '1'.
Pos: 47 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 19/24
Pos: 48 /Siebert/Bedienu ngsanleitungen/Seri eS1 02/SX102/Blinkmodi und A nzeigenattribute/ÜBS Blin kmodi undA nzeigenattribut e @ 4\mod_ 1485185305632_48. docx @ 27074 @ 1@ 1
B
10 Flashing modes and display attributes
Pos: 49 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Blinkmodi und Anz eigenattribute/S1 02Bli mnkmodi und Anzeige nattribute PFN RT @ 4\ mod_148518540 0259_48.docx @ 2 7081@ @ 1
The display can show the values to be displayed in a plurality of brightnesses and blinking patterns,
which are referred to as "display attribute".
For the initialization parameters, two blocks are defined: a block for 'standard attributes' (property
number 7), the other for 'out of range attributes' (property number 9). In each block the values 0%,
25%, 50% and 100% can be entered.
So, for example, the following typical display effects can be defined:
Effect
1/4
2/4
3/4
4/4
Attribute value
25% of the basic brightness
25%
25%
25%
25%
16#0055
50% of the basic brightness
50%
50%
50%
50%
16#00AA
100% of the basic brightness
100%
100%
100%
100%
16#00FF
Pulsation
0%
0%
0%
0%
16#0000
Brief flashing
0%
0%
0%
100%
16#0003
Fast flashing
0%
100%
0%
100%
16#0033
Slow flashing
0%
0%
100%
100%
16#000F
Short darkening
0%
100%
100%
100%
16#003F
Low beaming
0%
25%
50%
100%
16#001B
High beaming
100%
50%
25%
0%
16#00E4
If the value '0%' is entered in all four fields, the display switches to a pulsating display. This prevents
an inadvertent dark switching
The dark switching is possible by the global 'property 0'. Here the decimal point of the least significant
decade flashes.
Pos: 50 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S102 PFN RT 1.00 20/24
Pos: 51 /Siebert/Bedienu ngsanleitungen/Seri eS1 02/SX102/Flags/ÜB SFl ags@ 4 \mod_14851867832 23_48.docx @ 27087 @ 1 @ 1
Flags
11 Flags
Pos: 52 /Siebert/Bedi enungsanleitunge n/Serie S102/SX10 2/Flags/S102 Flags PFNRT @ 4\ mod_1485186833 733_48.docx @ 270 94@ @ 1
INT16 flags are to set specific display properties. In the delivery state, the flags are set to 16 # 00F6,
corresponding to 246 decimal.
Bit numbers
Default valuest
Meaning
0
0
Leading zeros (0 = off, 1 = on)
Leading zeros are automatically displayed.
1 + 2 = 00
Only with activated Smart-Dot-Function:
The decimal places are cut off.
1 + 2 = 10
Only with activated Smart-Dot-Function:
The decimal places are rounded.
1 + 2 = 01
Only with activated Smart-Dot-Function:
The decimal places are rounded off.
1 + 2 = 11
11
Only with activated Smart-Dot-Function:
The decimal places are rounded off commercially.
3
0
Smart-Dot-Function (0 = off, 1 = on)
When the Smart-Dot-Function is activated, the display automatically
moves the decimal point so that the decimal value is displayed
completely when the value exceeds the maximum display capacity..
4
1
Invalid initial vale (0 = off, 1 = on)
An invalid initial value is signalized by 3 horizontal lines at each
position.
5
1
Overflow (0 = off, 1 = on)
The value sent tot he display can not be displayed on the display.
6
1
Underflow (0 = off, 1 = on)
The value sent to the display can not be displayed on the display.
7
1
Circumferential frame (0 = off, 1 = on)
Until user data is received for the first time the display alternately
displays a frame or various status messages on its display.
8
0
Output of the number in decimal resp. hexadecimal form.
(0 = decimal, 1 = hexadecimal)
9…15
0
Without function. The bits are to be set to '0'.
Pos: 53 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1