Siemens 6MD85 User manual

SIPROTEC 5
High-Voltage Bay
Controller
6MD85/86
V7.50 and higher
Manual
C53000-G5040-C015-9
Preface
Open Source Software
Table of Contents
Introduction 1
Basic Structure of the Function 2
System Functions 3
Applications 4
Function-Group Types 5
Control Functions 6
Protection and Automation Functions 7
Supervision Functions 8
Measured Values, Energy Values, and
Supervision of the Primary System 9
Functional Tests 10
Technical Data 11
Appendix A
Glossary
Index

i
i
NOTE
For your own safety, observe the warnings and safety instructions contained in this document, if available.
Disclaimer of Liability
This document has been subjected to rigorous technical
review before being published. It is revised at regular inter-
vals, and any modifications and amendments are included
in the subsequent issues. The content of this document has
been compiled for information purposes only. Although
Siemens AG has made best efforts to keep the document as
precise and up-to-date as possible, Siemens AG shall not
assume any liability for defects and damage which result
through use of the information contained herein.
This content does not form part of a contract or of business
relations; nor does it change these. All obligations of
Siemens AG are stated in the relevant contractual agree-
ments.
Siemens AG reserves the right to revise this document from
time to time.
Document version: C53000-G5040-C015-9.02
Edition: 11.2017
Version of the product described: V7.50 and higher
Copyright
Copyright © Siemens AG 2017. All rights reserved.
The disclosure, duplication, distribution and editing of this
document, or utilization and communication of the content
are not permitted, unless authorized in writing. All rights,
including rights created by patent grant or registration of a
utility model or a design, are reserved.
Registered Trademarks
SIPROTEC®, DIGSI®, SIGUARD®, SIMEAS®, and SICAM® are
registered trademarks of Siemens AG. Any unauthorized
use is illegal. All other designations in this document can
be trademarks whose use by third parties for their own
purposes can infringe the rights of the owner.

Preface
Purpose of the Manual
This manual describes the functions of SIPROTEC 5 high voltage bay controllers.
Target Audience
Protection system engineers, commissioning engineers, persons entrusted with the setting, testing and main-
tenance of automation, selective protection and control equipment, and operational crew in electrical installa-
tions and power plants.
Scope
This manual applies to the SIPROTEC 5 device family.
Further Documentation
[dwprefdm-221012-01.tif, 3, en_US]
•Device manuals
Each Device manual describes the functions and applications of a specific SIPROTEC 5 device. The printed
manual and the online help for the device have the same informational structure.
•Hardware manual
The Hardware manual describes the hardware building blocks and device combinations of the SIPROTEC 5
device family.
•Operating manual
The Operating manual describes the basic principles and procedures for operating and assembling the
devices of the SIPROTEC 5 range.
SIPROTEC 5, High-Voltage Bay Controller, Manual 3
C53000-G5040-C015-9, Edition 11.2017

•Communication protocol manual
The Communication protocol manual contains a description of the protocols for communication within
the SIPROTEC 5 device family and to higher-level network control centers.
•Product information
The Product information includes general information about device installation, technical data, limiting
values for input and output modules, and conditions when preparing for operation. This document is
provided with each SIPROTEC 5 device.
•Engineering Guide
The Engineering Guide describes the essential steps when engineering with DIGSI 5. In addition, the Engi-
neering Guide shows you how to load a planned configuration to a SIPROTEC 5 device and update the
functionality of the SIPROTEC 5 device.
•DIGSI 5 online help
The DIGSI 5 online help contains a help package for DIGSI 5 and CFC.
The help package for DIGSI 5 includes a description of the basic operation of software, the DIGSI princi-
ples and editors. The help package for CFC includes an introduction to CFC programming, basic examples
of working with CFC, and a reference chapter with all the CFC blocks available for the SIPROTEC 5 range.
•SIPROTEC 5/DIGSI 5 Tutorial
The tutorial on the DVD contains brief information about important product features, more detailed infor-
mation about the individual technical areas, as well as operating sequences with tasks based on practical
operation and a brief explanation.
•SIPROTEC 5 catalog
The SIPROTEC 5 catalog describes the system features and the devices of SIPROTEC 5.
•Selection guide for SIPROTEC and Reyrolle
The selection guide offers an overview of the device series of the Siemens protection devices, and a
device selection table.
Indication of Conformity
This product complies with the directive of the Council of the European Communities
on harmonization of the laws of the Member States relating to electromagnetic
compatibility (EMC Directive 2014/30/EU) and concerning electrical equipment for use
within specified voltage limits (Low Voltage Directive 2014/35/EU).
This conformity has been proved by tests performed according to the Council Directive
in accordance with the product standard EN 60255-26 (for EMC directive) and with the
product standard EN 60255-27 (for Low Voltage Directive) by Siemens AG.
The device is designed and manufactured for application in an industrial environment.
The product conforms with the international standards of IEC 60255 and the German
standard VDE 0435.
Other Standards
IEEE Std C 37.90
The technical data of the product is approved in accordance with UL.
For more information about the UL database, see certified.ul.com
Select Online Certifications Directory and enter E194016 as UL File Number.
IND. CONT. EQ.
69CA
[ul_listed_c_us, 1, --_--]
Preface
4 SIPROTEC 5, High-Voltage Bay Controller, Manual
C53000-G5040-C015-9, Edition 11.2017

Additional Support
For questions about the system, please contact your Siemens sales partner.
Support
Our Customer Support Center provides a 24-hour service.
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
Training Courses
Inquiries regarding individual training courses should be addressed to our Training Center:
Siemens AG
Siemens Power Academy TD
Humboldtstraße 59
90459 Nürnberg
Germany
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
Internet: www.siemens.com/poweracademy
Notes on Safety
This document is not a complete index of all safety measures required for operation of the equipment (module
or device). However, it comprises important information that must be followed for personal safety, as well as
to avoid material damage. Information is highlighted and illustrated as follows according to the degree of
danger:
!
DANGER
DANGER means that death or severe injury will result if the measures specified are not taken.
²Comply with all instructions, in order to avoid death or severe injuries.
!
WARNING
WARNING means that death or severe injury may result if the measures specified are not taken.
²Comply with all instructions, in order to avoid death or severe injuries.
!
CAUTION
CAUTION means that medium-severe or slight injuries can occur if the specified measures are not taken.
²Comply with all instructions, in order to avoid moderate or minor injuries.
Preface
SIPROTEC 5, High-Voltage Bay Controller, Manual 5
C53000-G5040-C015-9, Edition 11.2017

NOTICE
NOTICE means that property damage can result if the measures specified are not taken.
²Comply with all instructions, in order to avoid property damage.
i
i
NOTE
Important information about the product, product handling or a certain section of the documentation
which must be given particular attention.
Qualified Electrical Engineering Personnel
Only qualified electrical engineering personnel may commission and operate the equipment (module, device)
described in this document. Qualified electrical engineering personnel in the sense of this manual are people
who can demonstrate technical qualifications as electrical technicians. These persons may commission,
isolate, ground and label devices, systems and circuits according to the standards of safety engineering.
Proper Use
The equipment (device, module) may be used only for such applications as set out in the catalogs and the
technical description, and only in combination with third-party equipment recommended and approved by
Siemens.
Problem-free and safe operation of the product depends on the following:
•Proper transport
•Proper storage, setup and installation
•Proper operation and maintenance
When electrical equipment is operated, hazardous voltages are inevitably present in certain parts. If proper
action is not taken, death, severe injury or property damage can result:
•The equipment must be grounded at the grounding terminal before any connections are made.
•All circuit components connected to the power supply may be subject to dangerous voltage.
•Hazardous voltages may be present in equipment even after the supply voltage has been disconnected
(capacitors can still be charged).
•Operation of equipment with exposed current-transformer circuits is prohibited. Before disconnecting the
equipment, ensure that the current-transformer circuits are short-circuited.
•The limiting values stated in the document must not be exceeded. This must also be considered during
testing and commissioning.
Preface
6 SIPROTEC 5, High-Voltage Bay Controller, Manual
C53000-G5040-C015-9, Edition 11.2017

Open Source Software
The product contains, among other things, Open Source Software developed by third parties. The Open
Source Software used in the product and the license agreements concerning this software can be found in the
Readme_OSS. These Open Source Software files are protected by copyright. Your compliance with those
license conditions will entitle you to use the Open Source Software as foreseen in the relevant license. In the
event of conflicts between Siemens license conditions and the Open Source Software license conditions, the
Open Source Software conditions shall prevail with respect to the Open Source Software portions of the soft-
ware. The Open Source Software is licensed royalty-free. Insofar as the applicable Open Source Software
License Conditions provide for it you can order the source code of the Open Source Software from your
Siemens sales contact - against payment of the shipping and handling charges - for a period of at least 3 years
since purchase of the Product. We are liable for the Product including the Open Source Software contained in
it pursuant to the license conditions applicable to the Product. Any liability for the Open Source Software
beyond the program flow intended for the Product is explicitly excluded. Furthermore any liability for defects
resulting from modifications to the Open Source Software by you or third parties is excluded. We do not
provide any technical support for the Product if it has been modified.
When using DIGSI 5 in online mode, you are provided with the option to go to the main menu Show open
source software information and read and display the Readme_OSS file containing the original license text
and copyright information.
To do this, the following steps are necessary:
•Switch to online mode.
•Select the device.
•Select Online in the menu bar.
•Click Show open source software information.
i
i
NOTE
To read the Readme_OSS file, a PDF viewer must be installed on the computer.
In order to operate SIPROTEC 5 devices, a valid DIGSI 5 license is required.
SIPROTEC 5, High-Voltage Bay Controller, Manual 7
C53000-G5040-C015-9, Edition 11.2017

8 SIPROTEC 5, High-Voltage Bay Controller, Manual
C53000-G5040-C015-9, Edition 11.2017

Table of Contents
Preface..........................................................................................................................................................3
Open Source Software..................................................................................................................................7
1 Introduction................................................................................................................................................31
1.1 General.............................................................................................................................32
1.2 Properties of SIPROTEC 5................................................................................................... 34
2 Basic Structure of the Function.................................................................................................................. 35
2.1 Function Embedding in the Device.................................................................................... 36
2.2 Adjustment of Application Templates/Functional Scope..................................................... 38
2.3 Function Control............................................................................................................... 40
2.4 Text Structure and Reference Number for Settings and Indications.....................................44
2.5 Information Lists...............................................................................................................45
3 System Functions....................................................................................................................................... 47
3.1 Indications........................................................................................................................48
3.1.1 General....................................................................................................................... 48
3.1.2 Reading Indications on the On-Site Operation Panel..................................................... 48
3.1.3 Reading Indications from the PC with DIGSI 5...............................................................50
3.1.4 Displaying Indications..................................................................................................51
3.1.5 Logs............................................................................................................................ 53
3.1.5.1 General..................................................................................................................53
3.1.5.2 Operational Log..................................................................................................... 55
3.1.5.3 Fault Log................................................................................................................56
3.1.5.4 Ground-Fault Log................................................................................................... 57
3.1.5.5 Setting-History Log.................................................................................................59
3.1.5.6 User Log................................................................................................................ 61
3.1.5.7 Security Log........................................................................................................... 63
3.1.5.8 Device-Diagnosis Log............................................................................................. 64
3.1.5.9 Communication Log...............................................................................................65
3.1.5.10 Motor-Starting Log.................................................................................................66
3.1.6 Saving and Deleting the Logs.......................................................................................68
3.1.7 Spontaneous Indication Display in DIGSI 5....................................................................69
3.1.8 Spontaneous Fault Display on the On-Site Operation Panel...........................................70
3.1.9 Stored Indications in the SIPROTEC 5 Device.................................................................71
3.1.10 Resetting Stored Indications of the Function Group ..................................................... 72
3.1.11 Test Mode and Influence of Indications on Substation Automation Technology ............72
3.2 Measured-Value Acquisition ............................................................................................. 73
3.3 Processing Quality Attributes.............................................................................................75
3.3.1 Overview.....................................................................................................................75
3.3.2 Quality Processing/Affected by the User for Received GOOSE Values............................. 77
SIPROTEC 5, High-Voltage Bay Controller, Manual 9
C53000-G5040-C015-9, Edition 11.2017

3.3.3 Quality Processing/Affected by the User in CFC Charts.................................................. 83
3.3.4 Quality Processing/Affected by the User in Internal Device Functions............................ 87
3.4 Fault Recording.................................................................................................................91
3.4.1 Overview of Functions ................................................................................................ 91
3.4.2 Structure of the Function.............................................................................................91
3.4.3 Function Description....................................................................................................91
3.4.4 Application and Setting Notes......................................................................................94
3.4.5 Settings.......................................................................................................................96
3.4.6 Information List...........................................................................................................96
3.5 Protection Communication................................................................................................97
3.5.1 Overview.....................................................................................................................97
3.5.2 Protection Interface and Protection Topology............................................................... 97
3.5.2.1 Overview of Functions........................................................................................... 97
3.5.2.2 Structure of the Function....................................................................................... 97
3.5.2.3 Function Description.............................................................................................. 98
3.5.2.4 Initialization and Configuration of the Protection Interface in DIGSI 5 ................... 108
3.5.2.5 Device-Combination Settings................................................................................109
3.5.2.6 Selecting the Connection..................................................................................... 111
3.5.2.7 Routing Information in DIGSI 5............................................................................. 112
3.5.2.8 Diagnostic Measured Values of the Protection Interface........................................ 118
3.5.2.9 Diagnostic Data for the Protection Interface..........................................................122
3.5.2.10 Settings............................................................................................................... 126
3.5.2.11 Information List................................................................................................... 127
3.6 Date and Time Synchronization....................................................................................... 129
3.6.1 Overview of Functions...............................................................................................129
3.6.2 Structure of the Function...........................................................................................129
3.6.3 Function Description..................................................................................................129
3.6.4 Application and Setting Notes....................................................................................132
3.6.5 Settings.....................................................................................................................135
3.6.6 Information List.........................................................................................................136
3.7 User-Defined Objects...................................................................................................... 137
3.7.1 Overview...................................................................................................................137
3.7.2 Basic Data Types........................................................................................................ 138
3.7.3 Pulse- and Energy- Metered Values ............................................................................141
3.7.4 Additional Data Types................................................................................................ 141
3.7.5 External Signals......................................................................................................... 141
3.8 Other Functions.............................................................................................................. 143
3.8.1 Signal Filtering and Chatter Blocking for Input Signals................................................ 143
3.8.2 Acquisition Blocking and Manual Updating.................................................................147
3.8.3 Persistent Commands................................................................................................ 149
3.8.4 Device Logoff............................................................................................................ 150
3.8.4.1 Overview............................................................................................................. 150
3.8.4.2 Application and Setting Notes.............................................................................. 151
3.8.4.3 Information List................................................................................................... 153
3.9 General Notes for Setting the Threshold Value of Protection Functions.............................154
3.9.1 Overview ..................................................................................................................154
3.9.2 Modifying the Transformer Ratios in DIGSI 5.............................................................. 154
3.9.3 Changing the Transformation Ratios of the Transformer on the Device....................... 161
Table of Contents
10 SIPROTEC 5, High-Voltage Bay Controller, Manual
C53000-G5040-C015-9, Edition 11.2017

3.10 Device Settings............................................................................................................... 162
3.10.1 Settings-Group Switching.......................................................................................... 162
3.10.1.1 Overview of Functions .........................................................................................162
3.10.1.2 Structure of the Function..................................................................................... 162
3.10.1.3 Function Description............................................................................................ 162
3.10.1.4 Application and Setting Notes.............................................................................. 163
3.10.1.5 Settings............................................................................................................... 164
3.10.1.6 Information List................................................................................................... 164
3.10.2 General Device Settings............................................................................................. 164
3.10.2.1 Overview ............................................................................................................ 164
3.10.2.2 Application and Setting Notes.............................................................................. 166
3.10.2.3 Settings............................................................................................................... 167
3.10.2.4 Information List................................................................................................... 167
3.10.3 Device Logoff............................................................................................................ 168
3.10.3.1 Overview............................................................................................................. 168
3.10.3.2 Application and Setting Notes.............................................................................. 169
3.10.3.3 Information List................................................................................................... 170
3.11 Security Settings in the Device.........................................................................................171
3.11.1 Multi-Level Safety Concept........................................................................................ 171
4 Applications..............................................................................................................................................173
4.1 Overview........................................................................................................................ 174
4.2 Application Templates and Functional Scope for Device 6MD85.......................................175
4.3 Application Templates and Functional Scope for Device 6MD86.......................................178
5 Function-Group Types.............................................................................................................................. 181
5.1 Power-System Data......................................................................................................... 182
5.1.1 Overview...................................................................................................................182
5.1.2 Structure of the Power-System Data...........................................................................182
5.1.3 Application and Setting Notes – General Settings....................................................... 182
5.1.4 Application and Setting Notes for Measuring Point Voltage 3-Phase (V-3ph)............... 183
5.1.5 Application and Setting Notes for Measuring Point Current 3-Phase (I-3ph)................ 186
5.1.6 Settings.....................................................................................................................189
5.1.7 Information List.........................................................................................................191
5.2 Function-Group Type Voltage/current 3-Phase................................................................. 193
5.2.1 Overview...................................................................................................................193
5.2.2 Structure of the Function Group................................................................................ 193
5.2.3 Application and Setting Notes ................................................................................... 197
5.2.4 Write-Protected Settings............................................................................................ 198
5.2.5 Settings.....................................................................................................................198
5.2.6 Information List.........................................................................................................198
5.3 Function-Group Type Voltage/current 1-Phase................................................................. 200
5.3.1 Overview...................................................................................................................200
5.3.2 Structure of the Function Group................................................................................ 200
5.3.3 Application and Setting Notes....................................................................................203
5.3.4 Write-Protected Settings............................................................................................ 204
5.3.5 Settings.....................................................................................................................204
5.3.6 Information List.........................................................................................................205
5.4 Function-Group Type Voltage 3-Phase............................................................................. 206
5.4.1 Overview...................................................................................................................206
Table of Contents
SIPROTEC 5, High-Voltage Bay Controller, Manual 11
C53000-G5040-C015-9, Edition 11.2017

5.4.2 Structure of the Function Group................................................................................ 206
5.4.3 Application and Setting Notes....................................................................................207
5.4.4 Settings.....................................................................................................................207
5.4.5 Information List.........................................................................................................208
5.5 Function-Group Type Circuit Breaker, 3-Pole.................................................................... 209
5.5.1 Overview...................................................................................................................209
5.5.2 Structure of the Function Group................................................................................ 210
5.5.3 Application and Setting Notes....................................................................................211
5.5.4 Settings.....................................................................................................................212
5.5.5 Information List.........................................................................................................213
5.5.6 Trip Logic.................................................................................................................. 213
5.5.6.1 Function Description............................................................................................ 213
5.5.6.2 Application and Setting Notes ............................................................................. 214
5.5.6.3 Settings............................................................................................................... 215
5.5.6.4 Information List................................................................................................... 215
5.5.7 Circuit Breaker........................................................................................................... 215
5.5.7.1 Overview............................................................................................................. 215
5.5.7.2 Tripping, Opening, and Closing the Circuit Breaker............................................... 215
5.5.7.3 Acquisition of Circuit-Breaker Auxiliary Contacts and Further Information..............216
5.5.7.4 Circuit-Breaker Tripping Alarm Suppression ..........................................................218
5.5.7.5 Tripping and Opening Information....................................................................... 219
5.5.7.6 Application and Setting Notes.............................................................................. 220
5.5.7.7 Settings............................................................................................................... 222
5.5.7.8 Information List................................................................................................... 223
5.5.8 Circuit-Breaker Position Recognition for Protection-Related Auxiliary Functions...........223
5.5.8.1 Overview............................................................................................................. 223
5.5.9 Detection Manual Closure (for AREC and Process Monitor)......................................... 224
5.5.9.1 Function Description............................................................................................ 224
5.5.9.2 Application and Setting Notes.............................................................................. 225
5.5.9.3 Settings............................................................................................................... 226
5.5.9.4 Information List................................................................................................... 226
5.6 Function-Group Type Circuit Breaker, 1-/3-Pole................................................................ 227
5.6.1 Overview ..................................................................................................................227
5.6.2 Structure of the Function Group ................................................................................227
5.6.3 Application and Setting Notes ................................................................................... 229
5.6.4 Trip Logic.................................................................................................................. 230
5.6.4.1 Function Description ........................................................................................... 230
5.6.4.2 Application and Setting Notes ............................................................................. 234
5.6.4.3 Settings............................................................................................................... 236
5.6.4.4 Information List................................................................................................... 236
5.6.5 Circuit Breaker........................................................................................................... 236
5.6.5.1 Overview ............................................................................................................ 236
5.6.5.2 Tripping, Opening, and Closing the Circuit Breaker ...............................................236
5.6.5.3 Acquisition of Circuit-Breaker Auxiliary Contacts and Further Information..............238
5.6.5.4 Definitive Tripping, Circuit-Breaker Tripping Alarm Suppression ............................239
5.6.5.5 Tripping and Opening Information....................................................................... 240
5.6.5.6 Application and Setting Notes.............................................................................. 241
5.6.5.7 Settings............................................................................................................... 245
5.6.5.8 Information List................................................................................................... 245
5.6.6 Circuit-Breaker Position Recognition for Protection-Related Auxiliary Functions...........246
5.6.6.1 Overview............................................................................................................. 246
5.6.7 Detection Manual Closure (for AREC and Process Monitor)......................................... 247
5.6.7.1 Function Description............................................................................................ 247
Table of Contents
12 SIPROTEC 5, High-Voltage Bay Controller, Manual
C53000-G5040-C015-9, Edition 11.2017

5.6.7.2 Application and Setting Notes.............................................................................. 247
5.6.7.3 Settings............................................................................................................... 248
5.6.7.4 Information List................................................................................................... 248
5.6.8 Settings.....................................................................................................................249
5.6.9 Information List.........................................................................................................250
5.7 Function-Group Type Analog Units.................................................................................. 253
5.7.1 Overview...................................................................................................................253
5.7.2 Structure of the Function Group................................................................................ 253
5.7.3 20-mA Unit Ethernet..................................................................................................255
5.7.3.1 Overview ............................................................................................................ 255
5.7.3.2 Structure of the Function..................................................................................... 255
5.7.3.3 Communication with 20-mA Unit Ethernet .......................................................... 256
5.7.3.4 Application and Setting Notes ............................................................................. 257
5.7.3.5 20-mA Channel....................................................................................................257
5.7.3.6 Application and Setting Notes.............................................................................. 260
5.7.3.7 Settings............................................................................................................... 261
5.7.3.8 Information List................................................................................................... 262
5.7.4 20-mA Unit Serial...................................................................................................... 262
5.7.4.1 Overview ............................................................................................................ 262
5.7.4.2 Application and Setting Notes.............................................................................. 262
5.7.4.3 Settings............................................................................................................... 264
5.7.4.4 Information List................................................................................................... 265
5.7.5 Communication with 20-mA Unit...............................................................................265
5.7.5.1 Integration of a Serial 20-mA Unit ........................................................................265
5.7.5.2 Integration of a 20-mA Unit Ethernet ...................................................................268
5.7.6 V/I-Measuring-Transducer Unit with Fast Inputs..........................................................270
5.7.6.1 Overview............................................................................................................. 270
5.7.6.2 Structure of the Function..................................................................................... 271
5.7.6.3 Function Description............................................................................................ 271
5.7.6.4 Application and Setting Notes.............................................................................. 272
5.7.6.5 Settings............................................................................................................... 276
5.7.6.6 Information List................................................................................................... 278
5.7.7 RTD Unit Ethernet......................................................................................................278
5.7.7.1 Overview............................................................................................................. 278
5.7.7.2 Structure of the Function..................................................................................... 278
5.7.7.3 Communication with an RTD Unit ........................................................................ 279
5.7.7.4 Application and Setting Notes.............................................................................. 280
5.7.7.5 Temperature Sensor.............................................................................................281
5.7.7.6 Application and Setting Notes ............................................................................. 281
5.7.7.7 Settings............................................................................................................... 282
5.7.7.8 Information List................................................................................................... 282
5.7.8 RTD Unit, Serial..........................................................................................................283
5.7.8.1 Overview ............................................................................................................ 283
5.7.8.2 Application and Setting Notes ............................................................................. 283
5.7.8.3 Settings............................................................................................................... 284
5.7.8.4 Information List................................................................................................... 285
5.7.9 Communication with RTD Unit................................................................................... 286
5.7.9.1 Integration of a Serial RTD Unit (Ziehl TR1200) .....................................................286
5.7.9.2 Integration of an RTD-Unit Ethernet (TR1200 IP) .................................................. 289
5.7.9.3 Temperature Simulation without Sensors ............................................................ 291
5.8 Process Monitor.............................................................................................................. 292
5.8.1 Overview of Functions...............................................................................................292
5.8.2 Structure of the Function...........................................................................................292
5.8.3 Current-Flow Criterion............................................................................................... 293
Table of Contents
SIPROTEC 5, High-Voltage Bay Controller, Manual 13
C53000-G5040-C015-9, Edition 11.2017

5.8.4 Application and Setting Notes (Current-Flow Criterion) ..............................................294
5.8.5 Settings.....................................................................................................................295
5.8.6 Circuit-Breaker Condition for the Protected Object......................................................295
5.8.7 Closure Detection...................................................................................................... 295
5.8.8 Information List.........................................................................................................296
5.8.9 Cold-Load Pickup Detection (Optional) ...................................................................... 297
5.8.10 Application and Setting Notes (Cold-Load Pickup Detection) ...................................... 298
5.8.11 Settings.....................................................................................................................299
5.8.12 Information List.........................................................................................................299
5.9 Voltage Measuring-Point Selection.................................................................................. 300
5.9.1 Overview of Functions...............................................................................................300
5.9.2 Function Description..................................................................................................300
5.9.3 Application and Setting Notes....................................................................................301
5.9.4 Information List.........................................................................................................302
6 Control Functions..................................................................................................................................... 303
6.1 Introduction....................................................................................................................304
6.1.1 Overview...................................................................................................................304
6.1.2 Concept of Controllables ...........................................................................................304
6.2 Switching Devices........................................................................................................... 307
6.2.1 General Overview...................................................................................................... 307
6.2.2 Switching Device Circuit Breaker................................................................................ 307
6.2.2.1 Structure of the Circuit-Breaker Switching Device..................................................307
6.2.2.2 Application and Setting Notes.............................................................................. 311
6.2.2.3 Connection Variants of the Circuit Breaker............................................................ 313
6.2.2.4 Settings............................................................................................................... 321
6.2.2.5 Information List................................................................................................... 323
6.2.3 Disconnector Switching Device.................................................................................. 325
6.2.3.1 Structure of the Disconnector Switching Device....................................................325
6.2.3.2 Application and Setting Notes.............................................................................. 329
6.2.3.3 Trigger Variants of the Disconnector.....................................................................331
6.2.3.4 Settings............................................................................................................... 334
6.2.3.5 Information List................................................................................................... 334
6.3 Control Functionality.......................................................................................................335
6.3.1 Command Checks and Switchgear Interlocking Protection..........................................335
6.3.2 Command Logging ................................................................................................... 353
6.3.3 Application Notes and Setting Notes for the External 1-of-n Check Function Block...... 358
6.3.4 Settings.....................................................................................................................359
6.3.5 Information List.........................................................................................................359
6.4 Synchronization Function................................................................................................360
6.4.1 Overview of Functions...............................................................................................360
6.4.2 Structure of the Function...........................................................................................360
6.4.3 Connection and Definition......................................................................................... 361
6.4.4 General Functionality................................................................................................ 365
6.4.4.1 Description.......................................................................................................... 365
6.4.4.2 Application and Setting Notes (General)............................................................... 368
6.4.4.3 Settings............................................................................................................... 371
6.4.5 Dynamic Measuring-Point Switching.......................................................................... 372
6.4.6 Sequence of Functions.............................................................................................. 375
Table of Contents
14 SIPROTEC 5, High-Voltage Bay Controller, Manual
C53000-G5040-C015-9, Edition 11.2017

6.4.7 Stage Synchrocheck...................................................................................................377
6.4.7.1 Description.......................................................................................................... 377
6.4.7.2 Application and Setting Notes.............................................................................. 378
6.4.7.3 Settings............................................................................................................... 378
6.4.7.4 Information List................................................................................................... 379
6.4.8 Stage Synchronous/Asynchronous............................................................................. 380
6.4.8.1 Description.......................................................................................................... 380
6.4.8.2 Application and Setting Notes.............................................................................. 384
6.4.8.3 Settings............................................................................................................... 386
6.4.8.4 Information List................................................................................................... 387
6.4.9 Stage Synchronous/Asynchronous with Balancing Commands....................................388
6.4.9.1 Description.......................................................................................................... 388
6.4.9.2 Application and Setting Notes.............................................................................. 395
6.4.9.3 Settings............................................................................................................... 405
6.4.9.4 Information List................................................................................................... 406
6.4.10 Expanded Checks (df/dt and Smoothing of Oscillations)............................................. 408
6.4.11 Closing at De-Energized Line/Busbar...........................................................................409
6.4.11.1 Description.......................................................................................................... 409
6.4.11.2 Application and Setting Notes.............................................................................. 410
6.4.12 Direct Close Command ..............................................................................................412
6.4.13 Interaction with Control and External Triggering ....................................................... 413
6.4.14 External Synchronization........................................................................................... 414
6.4.14.1 Description.......................................................................................................... 414
6.4.14.2 Application and Setting Notes (External Synchronization)..................................... 417
6.4.14.3 Settings............................................................................................................... 418
6.4.14.4 Information List................................................................................................... 420
6.4.15 Settings.....................................................................................................................420
6.4.16 Information List.........................................................................................................422
6.5 Switching Sequences...................................................................................................... 425
6.5.1 Overview of Functions .............................................................................................. 425
6.5.2 Function Description..................................................................................................425
6.5.3 Application and Setting Notes....................................................................................427
6.5.4 Settings.....................................................................................................................430
6.5.5 Information List.........................................................................................................431
6.6 User-Defined Function Block [Control].............................................................................432
6.6.1 Overview of Functions...............................................................................................432
6.6.2 Function Description..................................................................................................432
6.6.3 Application and Setting Notes....................................................................................432
6.6.4 Settings.....................................................................................................................433
6.6.5 Information List.........................................................................................................434
6.7 CFC-Chart Settings.......................................................................................................... 435
6.7.1 Overview of Functions...............................................................................................435
6.7.2 Function Description..................................................................................................435
6.7.3 Application and Setting Notes....................................................................................435
6.7.4 Settings.....................................................................................................................436
6.7.5 Information List.........................................................................................................436
6.8 Transformer Tap Changers.............................................................................................. 437
6.8.1 Function Description..................................................................................................437
6.8.2 Application and Setting Notes....................................................................................441
6.8.3 Settings (Properties Dialog)........................................................................................447
Table of Contents
SIPROTEC 5, High-Voltage Bay Controller, Manual 15
C53000-G5040-C015-9, Edition 11.2017

6.8.4 Settings.....................................................................................................................448
6.8.5 Information List.........................................................................................................448
6.9 Voltage Controller...........................................................................................................450
6.9.1 Overview of Functions...............................................................................................450
6.9.2 Structure of the Function...........................................................................................450
6.9.3 Function Description..................................................................................................451
6.9.3.1 General................................................................................................................451
6.9.3.2 Logic of the Function........................................................................................... 458
6.9.3.3 Control Response................................................................................................. 459
6.9.3.4 Function Supervision............................................................................................462
6.9.3.5 Line Compensation.............................................................................................. 462
6.9.3.6 Limiting Values.................................................................................................... 464
6.9.3.7 Blockings............................................................................................................. 464
6.9.3.8 Parallel Control.....................................................................................................465
6.9.3.9 Creating a GOOSE Later Binding for Parallel Control ............................................. 476
6.9.3.10 Functional Measured Values.................................................................................484
6.9.4 Application and Setting Notes....................................................................................488
6.9.4.1 General................................................................................................................488
6.9.4.2 Controlling...........................................................................................................490
6.9.4.3 Voltage Controller................................................................................................490
6.9.4.4 Line Compensation.............................................................................................. 495
6.9.4.5 Limiting Values.................................................................................................... 498
6.9.4.6 Blockings............................................................................................................. 499
6.9.4.7 Parallel control..................................................................................................... 500
6.9.5 Settings.....................................................................................................................501
6.9.6 Information List.........................................................................................................509
7 Protection and Automation Functions..................................................................................................... 515
7.1 Circuit-Breaker Failure Protection.....................................................................................516
7.1.1 Overview of Function................................................................................................ 516
7.1.2 Structure of the Function...........................................................................................516
7.1.3 Function Description..................................................................................................517
7.1.4 Application and Setting Notes....................................................................................528
7.1.5 Settings.....................................................................................................................537
7.1.6 Information List.........................................................................................................539
7.2 Automatic Reclosing Function......................................................................................... 542
7.2.1 Overview of Functions...............................................................................................542
7.2.2 Structure of the Function...........................................................................................542
7.2.3 Cooperation of the Automatic Reclosing Function and Protection Functions .............. 544
7.2.4 Cyclic Automatic Reclosing Function.......................................................................... 546
7.2.4.1 Operating Modes for Cyclic Automatic Reclosing Function.................................... 546
7.2.4.2 Structure of the Cyclic Automatic Reclosing Function............................................549
7.2.4.3 Input Logic for Operating Modes with Tripping .................................................... 550
7.2.4.4 Input Logic for Operating Modes with Pickup........................................................551
7.2.4.5 Start.................................................................................................................... 552
7.2.4.6 Cycle Control with Operating Mode 1: With Tripping/With Action Time..................553
7.2.4.7 Cycle Control with Operating Mode 2: With Pickup/With Action Time.................... 555
7.2.4.8 Cycle Control with Operating Mode 3: With Tripping/Without Action Time.............557
7.2.4.9 Cycle Control with Operating Mode 4: With Pickup/Without Action Time............... 558
7.2.4.10 Stage Release.......................................................................................................559
7.2.4.11 Dead Time for Operating Modes With Tripping .....................................................560
7.2.4.12 Dead Time for Operating Modes with Pickup ........................................................562
7.2.4.13 Evolving-Fault Detection During Dead Time.......................................................... 564
Table of Contents
16 SIPROTEC 5, High-Voltage Bay Controller, Manual
C53000-G5040-C015-9, Edition 11.2017

7.2.4.14 Closing Indication and Close Command ............................................................... 566
7.2.4.15 Reclaim Time....................................................................................................... 568
7.2.4.16 Circuit-Breaker Readiness and Circuit-Breaker Condition .......................................569
7.2.4.17 Blockings............................................................................................................. 571
7.2.4.18 Dead-Line Checking (DLC) and Reduced Dead Time (RDT)..................................... 574
7.2.4.19 Settings............................................................................................................... 576
7.2.4.20 Information List................................................................................................... 578
7.2.5 Automatic Reclosing Function with Adaptive Dead Time (ADT)................................... 580
7.2.5.1 Description.......................................................................................................... 580
7.2.5.2 Settings .............................................................................................................. 581
7.2.5.3 Information List................................................................................................... 581
7.2.6 Cooperation with External Automatic Reclosing Function........................................... 583
7.2.6.1 Description ......................................................................................................... 583
7.2.6.2 Information List................................................................................................... 584
7.2.7 Application and Setting Notes for General Settings ....................................................585
7.2.8 Application and Setting Notes for 1 Cycle of the Cyclic Automatic Reclosing Function 591
7.2.9 Information List.........................................................................................................594
7.3 External Trip Initiation 3-Pole.......................................................................................... 595
7.3.1 Overview of Functions...............................................................................................595
7.3.2 Structure of the Function...........................................................................................595
7.3.3 Stage Description ......................................................................................................596
7.3.4 Application and Setting Notes....................................................................................596
7.3.5 Settings.....................................................................................................................596
7.3.6 Information List.........................................................................................................597
7.4 Overcurrent Protection, Phases........................................................................................598
7.4.1 Overview of Functions .............................................................................................. 598
7.4.2 Structure of the Function .......................................................................................... 598
7.4.3 Filter for RMS Value Gain........................................................................................... 599
7.4.3.1 Description.......................................................................................................... 599
7.4.3.2 Application and Setting Notes.............................................................................. 600
7.4.3.3 Settings............................................................................................................... 601
7.4.3.4 Information List................................................................................................... 602
7.4.4 Stage with Definite-Time Characteristic Curve............................................................ 602
7.4.4.1 Description ......................................................................................................... 602
7.4.4.2 Application and Setting Notes ............................................................................. 606
7.4.4.3 Settings............................................................................................................... 609
7.4.4.4 Information List................................................................................................... 611
7.4.5 Stage with Inverse-Time Characteristic Curve............................................................. 613
7.4.5.1 Description ......................................................................................................... 613
7.4.5.2 Application and Setting Notes ............................................................................. 617
7.4.5.3 Settings............................................................................................................... 620
7.4.5.4 Information List................................................................................................... 622
7.4.6 Stage with User-Defined Characteristic Curve............................................................. 622
7.4.6.1 Description ......................................................................................................... 622
7.4.6.2 Application and Setting Notes ............................................................................. 624
7.4.6.3 Settings............................................................................................................... 625
7.4.6.4 Information List................................................................................................... 628
7.4.7 Blocking of the Tripping by Device-Internal Inrush-Current Detection..........................628
7.4.7.1 Description ......................................................................................................... 628
7.4.7.2 Application and Setting Notes ............................................................................. 629
7.4.8 Influence of Other Functions via Dynamic Settings.....................................................629
7.4.8.1 Description ......................................................................................................... 629
7.4.8.2 Application and Setting Notes (Advanced Stage) ..................................................633
Table of Contents
SIPROTEC 5, High-Voltage Bay Controller, Manual 17
C53000-G5040-C015-9, Edition 11.2017

7.5 Overcurrent Protection, Ground...................................................................................... 634
7.5.1 Overview of Functions...............................................................................................634
7.5.2 Structure of the Function...........................................................................................634
7.5.3 General Functionality................................................................................................ 635
7.5.3.1 Description.......................................................................................................... 635
7.5.3.2 Application and Setting Notes ............................................................................. 636
7.5.3.3 Settings............................................................................................................... 637
7.5.4 Stage with Definite-Time Characteristic Curve............................................................ 638
7.5.4.1 Description ......................................................................................................... 638
7.5.4.2 Application and Setting Notes ............................................................................. 640
7.5.4.3 Settings............................................................................................................... 642
7.5.4.4 Information List................................................................................................... 647
7.5.5 Stage with Inverse-Time Characteristic Curve............................................................. 648
7.5.5.1 Description ......................................................................................................... 648
7.5.5.2 Application and Setting Notes ............................................................................. 651
7.5.5.3 Settings............................................................................................................... 652
7.5.5.4 Information List................................................................................................... 655
7.5.6 Stage with User-Defined Characteristic Curve............................................................. 655
7.5.6.1 Description ......................................................................................................... 655
7.5.6.2 Application and Setting Notes ............................................................................. 657
7.5.6.3 Settings............................................................................................................... 658
7.5.6.4 Information List................................................................................................... 660
7.5.7 Blocking of the Tripping by Device-Internal Inrush-Current Detection..........................661
7.5.7.1 Description.......................................................................................................... 661
7.5.7.2 Application and Setting Notes ............................................................................. 661
7.5.8 Influence of Other Functions via Dynamic Settings.....................................................662
7.5.8.1 Description ......................................................................................................... 662
7.5.8.2 Application and Setting Notes (Advanced Stage) ..................................................666
7.6 Directional Overcurrent Protection, Phases...................................................................... 667
7.6.1 Overview of Functions .............................................................................................. 667
7.6.2 Structure of the Function .......................................................................................... 667
7.6.3 Stage Control............................................................................................................ 667
7.6.3.1 Description ......................................................................................................... 667
7.6.3.2 Application and Setting Notes ............................................................................. 668
7.6.4 Stage with Definite-Time Characteristic Curve............................................................ 669
7.6.4.1 Description ......................................................................................................... 669
7.6.4.2 Application and Setting Notes ............................................................................. 672
7.6.4.3 Settings............................................................................................................... 674
7.6.4.4 Information List................................................................................................... 679
7.6.5 Stage with Inverse-Time Characteristic Curve............................................................. 680
7.6.5.1 Description ......................................................................................................... 680
7.6.5.2 Application and Setting Notes ............................................................................. 683
7.6.5.3 Settings............................................................................................................... 685
7.6.5.4 Information List................................................................................................... 688
7.6.6 Stage with User-Defined Characteristic Curve............................................................. 689
7.6.6.1 Description ......................................................................................................... 689
7.6.6.2 Application and Setting Notes ............................................................................. 690
7.6.6.3 Settings............................................................................................................... 691
7.6.6.4 Information List................................................................................................... 693
7.6.7 Direction Determination............................................................................................ 694
7.6.7.1 Description ......................................................................................................... 694
7.6.7.2 Application and Setting Notes ............................................................................. 696
7.6.8 Influence of Other Functions via Dynamic Settings .................................................... 697
7.6.9 Application Notes for Parallel Lines ............................................................................697
Table of Contents
18 SIPROTEC 5, High-Voltage Bay Controller, Manual
C53000-G5040-C015-9, Edition 11.2017

7.6.10 Application Notes for Directional Comparison Protection ........................................... 698
7.7 Directional Overcurrent Protection, Ground..................................................................... 700
7.7.1 Overview of Functions...............................................................................................700
7.7.2 Structure of the Function...........................................................................................700
7.7.3 General Functionality................................................................................................ 702
7.7.3.1 Measured-Value Selection.................................................................................... 702
7.7.3.2 Direction Determination.......................................................................................703
7.7.3.3 Application and Setting Notes.............................................................................. 705
7.7.3.4 Settings............................................................................................................... 707
7.7.3.5 Information List................................................................................................... 708
7.7.4 Stage Control............................................................................................................ 708
7.7.4.1 Description.......................................................................................................... 708
7.7.4.2 Application and Setting Notes.............................................................................. 708
7.7.5 Stage with Definite-Time Characteristic Curve............................................................ 710
7.7.5.1 Description.......................................................................................................... 710
7.7.5.2 Application and Setting Notes.............................................................................. 713
7.7.5.3 Settings............................................................................................................... 715
7.7.5.4 Information List................................................................................................... 718
7.7.6 Stage with Inverse-Time Characteristic Curve............................................................. 719
7.7.6.1 Description.......................................................................................................... 719
7.7.6.2 Application and Setting Notes.............................................................................. 723
7.7.6.3 Settings............................................................................................................... 726
7.7.6.4 Information List................................................................................................... 728
7.7.7 Stage with Inverse-Time Overcurrent Protection with Logarithmic-Inverse Char-
acteristic Curve..........................................................................................................730
7.7.7.1 Description.......................................................................................................... 730
7.7.7.2 Application and Setting Notes.............................................................................. 732
7.7.7.3 Settings............................................................................................................... 733
7.7.7.4 Information List................................................................................................... 735
7.7.8 Stage with Knee-Point Characteristic Curve................................................................ 736
7.7.8.1 Description.......................................................................................................... 736
7.7.8.2 Application and Setting Notes.............................................................................. 737
7.7.8.3 Settings............................................................................................................... 738
7.7.8.4 Information List................................................................................................... 739
7.7.9 Stage with User-Defined Characteristic Curve............................................................. 740
7.7.9.1 Description.......................................................................................................... 740
7.7.9.2 Application and Setting Notes.............................................................................. 741
7.7.9.3 Settings............................................................................................................... 742
7.7.9.4 Information List................................................................................................... 745
7.7.10 Influence of Other Functions via Dynamic Settings.....................................................745
7.8 Overcurrent Protection, 1-Phase...................................................................................... 746
7.8.1 Function Overview ....................................................................................................746
7.8.2 Structure of the Function .......................................................................................... 746
7.8.3 Stage with Definite-Time Characteristic Curve............................................................ 748
7.8.3.1 Description ......................................................................................................... 748
7.8.3.2 Application and Setting Notes ............................................................................. 749
7.8.3.3 Settings............................................................................................................... 750
7.8.3.4 Information List................................................................................................... 750
7.8.4 Stage with Inverse-Time Characteristic Curve............................................................. 752
7.8.4.1 Description ......................................................................................................... 752
7.8.4.2 Application and Setting Notes ............................................................................. 753
7.8.4.3 Settings............................................................................................................... 754
7.8.4.4 Information List................................................................................................... 755
Table of Contents
SIPROTEC 5, High-Voltage Bay Controller, Manual 19
C53000-G5040-C015-9, Edition 11.2017

7.8.5 Stage with User-Defined Characteristic Curve............................................................. 755
7.8.5.1 Description ......................................................................................................... 755
7.8.5.2 Application and Setting Notes ............................................................................. 756
7.8.5.3 Settings............................................................................................................... 757
7.8.5.4 Information List................................................................................................... 758
7.9 Group Indications of Overcurrent Protection Functions.................................................... 759
7.9.1 Description ............................................................................................................... 759
7.10 Inrush-Current Detection.................................................................................................760
7.10.1 Overview of Functions...............................................................................................760
7.10.2 Structure of the Function .......................................................................................... 760
7.10.3 Function Description..................................................................................................760
7.10.4 Application and Setting Notes....................................................................................764
7.10.5 Settings.....................................................................................................................765
7.10.6 Information List.........................................................................................................766
7.11 Instantaneous High-Current Tripping...............................................................................767
7.11.1 Overview of Functions .............................................................................................. 767
7.11.2 Structure of the Function .......................................................................................... 767
7.11.3 Standard Release Procedure.......................................................................................768
7.11.4 Application and Setting Notes ................................................................................... 769
7.11.5 Release Procedure via Protection Interface................................................................. 770
7.11.6 Application and Setting Notes ................................................................................... 772
7.11.7 Settings.....................................................................................................................772
7.11.8 Information List.........................................................................................................772
7.12 Voltage-Dependent Overcurrent Protection..................................................................... 774
7.12.1 Overview of Functions...............................................................................................774
7.12.2 Structure of the Function...........................................................................................774
7.12.3 Stage Description Overcurrent Protection, Voltage-Dependent................................... 775
7.12.3.1 Description.......................................................................................................... 775
7.12.3.2 Application and Setting Notes.............................................................................. 777
7.12.3.3 Settings............................................................................................................... 779
7.12.3.4 Information List................................................................................................... 779
7.12.4 Stage Description Voltage-Independent Overcurrent Protection..................................780
7.12.4.1 Description.......................................................................................................... 780
7.12.4.2 Application and Setting Notes.............................................................................. 781
7.12.4.3 Settings............................................................................................................... 782
7.12.4.4 Information List................................................................................................... 782
7.13 Overvoltage Protection with 3-Phase Voltage...................................................................783
7.13.1 Overview of Functions .............................................................................................. 783
7.13.2 Structure of the Function...........................................................................................783
7.13.3 Description ............................................................................................................... 784
7.13.4 Application and Setting Notes ................................................................................... 785
7.13.5 Settings.....................................................................................................................787
7.13.6 Information List.........................................................................................................787
7.13.7 Description ............................................................................................................... 789
7.13.8 Application and Setting Notes ................................................................................... 791
7.13.9 Settings.....................................................................................................................793
7.13.10 Information List.........................................................................................................793
Table of Contents
20 SIPROTEC 5, High-Voltage Bay Controller, Manual
C53000-G5040-C015-9, Edition 11.2017