Siemens SINAMICS PERFECT HARMONY GH150 6SL3826 User manual

www.siemens.com/drives
Medium-Voltage Drive
SINAMICS PERFECT HARMONY GH150
Type 6SL3826
Operating Instructions
Installation Instructions
Edition 05/2020

19.06.2020 09:25
V14.00

Medium-Voltage Drive
SINAMICS PERFECT HARMONY
GH150
Type 6SL3826
Operating Instructions
Installation Instructions
Edition 05/2020
Introduction 1
Safety instructions 2
Description 3
Preparations for use 4
Assembly 5
Electrical connection 6
Commissioning 7
Operation 8
Maintenance 9
Spare parts 10
Disposal 11
Service & Support A
Technical data and drawings B
Quality documents C
Additional documents D

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Large Drives Applications
Vogelweiherstr. 1-15
90441 NÜRNBERG
GERMANY
Document order number: 6SL3826
Ⓟ 06/2020 Subject to change
Copyright © Siemens AG 2020.
All rights reserved

Table of contents
1 Introduction.................................................................................................................................................11
1.1 About these instructions.........................................................................................................11
2 Safety instructions ......................................................................................................................................13
2.1 Warning symbols on the device .............................................................................................13
2.2 Qualified personnel ................................................................................................................13
2.3 The 5 safety rules...................................................................................................................13
2.4 Safe handling .........................................................................................................................14
2.5 Electromagnetic fields in electrical power engineering installations ......................................16
2.6 Components that can be destroyed by electrostatic discharge (ESD)...................................17
2.7 Information for persons responsible for plants and systems..................................................18
2.7.1 Proper usage..........................................................................................................................18
2.7.2 Grounding concept.................................................................................................................19
2.7.3 Installation site safety.............................................................................................................20
2.7.4 Measures for operator protection in electromagnetic fields ...................................................20
2.7.5 Requirements for the circuit breaker provided by the customer.............................................21
2.8 Residual risks.........................................................................................................................21
2.9 Security information ...............................................................................................................23
3 Description..................................................................................................................................................25
3.1 Area of application .................................................................................................................25
3.2 Safety concept .......................................................................................................................25
3.2.1 Safety components and functions ..........................................................................................25
3.2.2 External safety components...................................................................................................26
3.2.3 Protection and monitoring functions of internal components .................................................26
3.2.4 Protection and monitoring functions for external components ...............................................26
3.3 Control Module.......................................................................................................................26
3.4 Basic Line Module..................................................................................................................27
3.5 Motor Module employing M2C technology.............................................................................27
3.6 Air cooling ..............................................................................................................................29
3.7 Components...........................................................................................................................30
3.7.1 Control Unit ............................................................................................................................31
3.7.2 Power Stack Adapter .............................................................................................................31
3.7.3 Terminal Modules...................................................................................................................34
3.7.4 Power cell...............................................................................................................................34
3.7.4.1 IGBT module ..........................................................................................................................35
3.7.4.2 Capacitor bank .......................................................................................................................35
3.7.5 Mechanical door interlock system ..........................................................................................35
3.7.6 Precharging............................................................................................................................36
SINAMICS PERFECT HARMONY GH150 6SL3826
Operating Instructions 05/2020 5

3.7.7 Actual value sensing ..............................................................................................................36
3.7.8 Power supply (for ≥42 cells)...................................................................................................36
3.7.8.1 Field of application .................................................................................................................36
3.7.8.2 Connections ...........................................................................................................................38
3.7.9 Touch screen operator panel .................................................................................................41
3.7.10 DC/DC converter....................................................................................................................41
3.7.11 Line filter.................................................................................................................................42
3.7.12 SIRIUS safety relay................................................................................................................42
3.7.13 Auxiliary power supply ...........................................................................................................43
3.7.13.1 1 AC auxiliary voltage ............................................................................................................43
3.7.13.2 3 AC auxiliary voltage supply ................................................................................................44
3.8 Options...................................................................................................................................44
3.8.1 Expanded remote control via terminal block (option A06)......................................................44
3.8.2 Fan in the Control Module (option A20) .................................................................................44
3.8.3 Auxiliary voltage supply 3 AC 380 V 50 Hz (option C36) .......................................................45
3.8.4 Auxiliary voltage supply 3 AC 380 V 60 Hz (option C37) .......................................................45
3.8.5 Auxiliary voltage supply 3 AC 415 V 50 Hz (option C39) .......................................................45
3.8.6 Auxiliary voltage supply 3 AC 440 V 60 Hz (option C40) .......................................................45
3.8.7 Auxiliary voltage supply 3 AC 460 V 60 Hz (option C41) .......................................................45
3.8.8 Auxiliary voltage for the open-loop and closed-loop control (option C55)..............................45
3.8.9 Can Bus interface (option G20)..............................................................................................45
3.8.10 PROFINET interface (option G24) .........................................................................................45
3.8.11 Modbus Plus interface (option G21).......................................................................................46
3.8.12 Modbus RTU Slave interface (option G22) ............................................................................46
3.8.13 DeviceNet interface (option G23)...........................................................................................46
3.8.14 Control Net interface (option G26) .........................................................................................46
3.8.15 Modbus Ethernet interface (option G28) ................................................................................46
3.8.16 Ethernet connection in the door (option G47) ........................................................................46
3.8.17 1x temperature sensor evaluation unit TM150 (option G51)..................................................46
3.8.18 2x temperature sensor evaluation units TM150 (option G52) ................................................46
3.8.19 Terminal Module TM31 (option G61) .....................................................................................47
3.8.20 Second Terminal Module TM31 (option G62) ........................................................................47
3.8.21 Additional Terminal Module TM15 (option G63) ....................................................................48
3.8.22 Pulse distributor for splitting speed encoder signal (option G70)...........................................48
3.8.23 Indicator lamps in the cabinet door (option K20)....................................................................48
3.8.24 Display instruments in the cabinet door for voltage, current, speed, and output plus
indicator lamps (option K21) ..................................................................................................48
3.8.25 Display instruments in the cabinet door for current, speed, output and winding
temperature plus indicator lamps (option K22) ......................................................................49
3.8.26 Sensor Module SMC30 (option K50) .....................................................................................49
3.8.27 CU320-2 DP Control Unit (option K90) ..................................................................................49
3.8.28 Automatic restart function (option L32) ..................................................................................50
3.8.29 Emergency mushroom-head pushbutton (option L45)...........................................................50
3.8.30 Cabinet lighting in the control section (option L50) ................................................................50
3.8.31 Uninterruptible power supply (option L53) .............................................................................50
3.8.32 Anti-condensation heating (option L55) .................................................................................51
3.8.33 EMERGENCY STOP Category 0 (option L66) ......................................................................51
3.8.34 Safety locking system (option M08) .......................................................................................52
3.8.35 Safety locking system (option M09) .......................................................................................52
3.8.36 Safety locking system (option M10) .......................................................................................52
3.8.37 Connection of auxiliary voltage and signal cable from above (option M34) ...........................53
3.8.38 Brass cable entry for power and signal cables (option M36) .................................................53
Table of contents
SINAMICS PERFECT HARMONY GH150 6SL3826
6Operating Instructions 05/2020

3.8.39 Stainless steel cable entry for the power cable (option M37).................................................53
3.8.40 IP42 degree of protection (option M42)..................................................................................53
3.8.41 IP54 degree of protection (option M54)..................................................................................53
3.8.42 Arcing fault strength (option M57) ..........................................................................................53
3.8.43 Redundant fan (option M61) ..................................................................................................54
3.8.44 Suitability for marine use (option M66)...................................................................................54
3.8.45 Controlled outgoing circuit for anti-condensation heating 1-phase 120 VAC (option N37)......54
3.8.46 CSA mark (option U03) ..........................................................................................................55
3.8.47 CE conformance (option U02)................................................................................................55
3.8.48 Cell bypass (Option U11) .......................................................................................................55
3.8.49 Customer-specific version (option X30) .................................................................................55
3.9 Interfaces ...............................................................................................................................55
3.9.1 DRIVE-CLiQ interface ............................................................................................................55
4 Preparations for use ...................................................................................................................................57
4.1 Requirements for installation location ....................................................................................57
4.2 Inspections when the equipment is received .........................................................................57
4.2.1 Checking shock and tilt indicators..........................................................................................57
4.2.2 Checking the load handling attachments ...............................................................................58
4.3 Transport................................................................................................................................59
4.3.1 Transport markings ................................................................................................................59
4.3.2 Transport requirements..........................................................................................................59
4.3.3 Observe center of gravity .......................................................................................................60
4.3.4 Transport with a fork-lift truck.................................................................................................60
4.3.5 Transport with a crane ...........................................................................................................61
4.3.6 Transporting transportation units packed in boxes ................................................................61
4.4 Unpacking the cabinets..........................................................................................................63
4.4.1 Removing the packaging........................................................................................................63
4.4.2 Removing load securing devices ...........................................................................................63
4.4.3 Lifting the cabinet off the transport pallet ...............................................................................64
4.4.4 Opening doors in preparation for use.....................................................................................64
4.4.5 Checking the shock and tilt indicators inside the cabinet.......................................................64
4.5 Storage...................................................................................................................................65
4.5.1 Storing a device .....................................................................................................................65
4.5.2 Storing fans ............................................................................................................................66
5 Assembly ....................................................................................................................................................67
5.1 Safety instructions for assembly ............................................................................................67
5.2 Tools required ........................................................................................................................68
5.3 Screwing the transport units together ....................................................................................68
5.4 Connect to the foundation ......................................................................................................69
5.5 Connecting cabinets...............................................................................................................70
6 Electrical connection...................................................................................................................................71
6.1 Safety instructions for electrical connections .........................................................................71
6.2 Electromagnetic compatibility.................................................................................................73
6.3 Potential concept....................................................................................................................76
Table of contents
SINAMICS PERFECT HARMONY GH150 6SL3826
Operating Instructions 05/2020 7

6.4 Cable cross-sections..............................................................................................................76
6.5 Connecting ground.................................................................................................................77
6.6 Laying the signal lines............................................................................................................77
6.7 Connecting the auxiliary voltage ............................................................................................78
6.8 Connecting power cables.......................................................................................................79
6.8.1 Preparations...........................................................................................................................79
6.8.2 Procedure...............................................................................................................................80
6.8.3 Shield connection...................................................................................................................80
6.9 Interconnecting optional connections.....................................................................................81
6.10 Fastening the cable ducts with cable ties...............................................................................82
7 Commissioning ...........................................................................................................................................83
7.1 Commissioning.......................................................................................................................83
7.2 Safety instructions for commissioning....................................................................................83
7.3 STARTER software................................................................................................................84
8 Operation....................................................................................................................................................85
8.1 Safety instructions for operation.............................................................................................85
8.2 Operating the converter .........................................................................................................86
8.3 Functions................................................................................................................................86
8.3.1 Monitoring functions and protective functions ........................................................................86
8.3.1.1 Insulation monitoring ..............................................................................................................86
8.3.1.2 Tripping of the circuit-breaker in case of undervoltage ..........................................................87
8.3.1.3 Automatic restart ....................................................................................................................87
8.4 Fault and system messages ..................................................................................................89
8.4.1 Indicating and rectifying faults................................................................................................89
8.4.2 Diagnostics via LEDs .............................................................................................................89
8.4.2.1 LEDs of the Power Stack Adapters........................................................................................89
8.4.2.2 LEDs of the SIRIUS safety relay ............................................................................................90
9 Maintenance ...............................................................................................................................................91
9.1 Safety instructions for maintenance .......................................................................................91
9.2 Grounding the system ............................................................................................................93
9.3 Opening the device ................................................................................................................93
9.3.1 Door interlock options ............................................................................................................93
9.3.2 Open the doors ......................................................................................................................94
9.4 Preventive maintenance.........................................................................................................96
9.4.1 Inspection...............................................................................................................................96
9.4.2 Checklist for preventive maintenance work............................................................................97
9.4.3 Visual inspections ..................................................................................................................98
9.4.3.1 Equipment for visual inspections............................................................................................98
9.4.3.2 Checking the isolating clearances..........................................................................................98
9.4.3.3 Checking the plug connections. .............................................................................................98
9.4.3.4 Checking the cable and screw terminals................................................................................99
Table of contents
SINAMICS PERFECT HARMONY GH150 6SL3826
8Operating Instructions 05/2020

9.5 Maintenance...........................................................................................................................99
9.5.1 Replacing a fan ......................................................................................................................99
9.5.1.1 Lubricating fan bearings.........................................................................................................99
9.5.1.2 Replacing fans, from the front ................................................................................................99
9.6 Cleaning ...............................................................................................................................102
9.6.1 Cleaning aluminum parts .....................................................................................................102
9.7 Repair...................................................................................................................................102
9.7.1 Components that can be replaced .......................................................................................104
9.7.2 Torques ................................................................................................................................104
9.7.3 Replacing the AVT combination module ..............................................................................106
9.7.4 Replacing the current transformer........................................................................................107
9.7.5 Replacing the precharging transformer................................................................................108
9.7.6 Replacing the precharging rectifier ......................................................................................109
9.7.7 Replacing a power cell .........................................................................................................110
9.7.8 Replacing a diode stack .......................................................................................................113
9.7.8.1 Removing .............................................................................................................................114
9.7.9 Replacing temperature sensors ...........................................................................................115
9.7.10 Replacing the HMI operator panel .......................................................................................116
9.7.11 Replacing the CompactFlash card .......................................................................................118
10 Spare parts ...............................................................................................................................................119
11 Disposal....................................................................................................................................................121
11.1 Information according to Article 33 of the REACH regulation ..............................................121
11.2 Disposing of packaging material ..........................................................................................121
11.3 Removing device components and old devices ...................................................................122
11.4 Bypass disposal ...................................................................................................................122
A Service & Support.....................................................................................................................................123
B Technical data and drawings....................................................................................................................125
B.1 Standards and regulations ...................................................................................................125
B.2 Environmental conditions .....................................................................................................126
C Quality documents....................................................................................................................................129
D Additional documents ...............................................................................................................................131
Index.........................................................................................................................................................133
Tables
Table 3-1 Interface description....................................................................................................................39
Table 3-2 Optical indicator...........................................................................................................................39
Table 3-3 DRIVE-CLiQ interface .................................................................................................................55
Table 6-1 Cable cross-sections...................................................................................................................76
Table 8-1 LEDs of the Power Stack Adapters ............................................................................................89
Table 8-2 LEDs of the SIRIUS safety relay ................................................................................................90
Table of contents
SINAMICS PERFECT HARMONY GH150 6SL3826
Operating Instructions 05/2020 9

Table 9-1 General checklist for preventive maintenance work....................................................................97
Table 9-2 Control Module: Checklist for preventive maintenance work ......................................................97
Table 9-3 Tightening torque for screws.....................................................................................................105
Table 9-4 Tightening torques for screw terminals for copper cables without cable lug 1).........................105
Table B-1 Standards and regulations ........................................................................................................125
Table B-2 Climatic environmental conditions.............................................................................................126
Table B-3 Mechanical ambient conditions .................................................................................................126
Table B-4 Other ambient conditions ..........................................................................................................127
Figures
Figure 2-1 ESD information ..........................................................................................................................18
Figure 3-1 Block diagram: Basic Line Module with diodes ...........................................................................27
Figure 3-2 Block diagram: Motor Module employing M2C technology .........................................................28
Figure 3-3 Interface overview of Power Stack Adapter 4 .............................................................................32
Figure 3-4 Interface overview of Power Stack Adapter 5 .............................................................................33
Figure 3-5 Power cell....................................................................................................................................34
Figure 3-6 Operator panel ...........................................................................................................................41
Figure 3-7 Line filter......................................................................................................................................42
Figure 3-8 SIRIUS 3SK.................................................................................................................................43
Figure 4-1 Example of attaching and displaying the shock and tilt indicators ..............................................58
Figure 4-2 Example illustration of centers of gravity.....................................................................................60
Figure 4-3 Transporting a transportation unit (still in packaging) with a crane .............................................62
Figure 6-1 Shield connection using a clip.....................................................................................................75
Figure 6-2 Bridging shield gaps....................................................................................................................75
Figure 6-3 Potential concept.........................................................................................................................76
Figure 6-4 Shield connection........................................................................................................................81
Figure 6-5 Schematic diagram: Fastening the cable ties..............................................................................82
Figure 9-1 Control cabinet door with EMERGENCY OFF button (L45)........................................................94
Figure 9-2 DC link voltage in parameter r70(0) of the DFEMV in STARTER ...............................................95
Figure 9-3 Details of the power cell with LED that indicates a voltage above 120 V DC .............................96
Figure 9-4 Removing the fan ......................................................................................................................100
Figure 9-5 Installing the fan ........................................................................................................................101
Figure 9-6 Example of an AVT combination module ..................................................................................106
Figure 9-7 Replacing the current transformer.............................................................................................107
Figure 9-8 Example diagram: Replacing the pre-charging rectifier ............................................................109
Figure 9-9 Removing a power cell..............................................................................................................112
Figure 9-10 Removing diode stack modules ................................................................................................114
Figure 9-11 Diode stack module ..................................................................................................................115
Table of contents
SINAMICS PERFECT HARMONY GH150 6SL3826
10 Operating Instructions 05/2020

Introduction 1
1.1 About these instructions
These Operating Instructions describe the device and provide you with information about
handling it - from the initial shipment up to disposal. Keep these instructions for later use.
Read these Operating Instructions and comply with the information provided in them. In this
way you can ensure safe, problem-free operation and a long service life.
Safety information and handling-related warnings are provided in these Operating Instructions.
For your own safety, the safety of other persons and to avoid material damage, carefully follow
these instructions when carrying out any work.
If you have suggestions for improving the document, please contact our Service Center
(Page 123).
Text format features
You can find the following text format features in these instructions:
1. Handling instructions are always formatted as a numbered list. Always perform the steps in
the order given.
● Lists are formatted as bulleted lists.
– Lists on the second level are hyphenated.
Note
The note provides you with additional information about the product itself, handling the product
- and the relevant documentation.
SINAMICS PERFECT HARMONY GH150 6SL3826
Operating Instructions 05/2020 11

Introduction
1.1 About these instructions
SINAMICS PERFECT HARMONY GH150 6SL3826
12 Operating Instructions 05/2020

Safety instructions 2
In the individual chapters of this document, you will find safety instructions that must be obeyed
absolutely, for your own safety, to protect other people and to avoid damage to property.
Carefully comply with the following safety instructions when performing all of the activities.
2.1 Warning symbols on the device
Please observe the warning symbols attached to the device. The warning symbols have the
following meaning:
Warning symbol Meaning
Warning: Voltage
Warning: Hot surface
General warning symbol: Observe the explanations about the hazard on the
device labels.
For transportation, observe the "transportation markings (Page 59)" on the device packaging.
2.2 Qualified personnel
The product/system described in this documentation may only be operated by personnel
qualified for the specific task in accordance with the relevant documentation for the specific
task, in particular its warning notices and safety instructions. Because of their training and
experience, qualified personnel can recognize any risks involved with handling these products/
systems and avoid any possible dangers.
2.3 The 5 safety rules
To ensure your own personal safety as well as to avoid material damage, always comply with
the safety-relevant instructions when carrying out any work. Also carefully comply with the 5
safety rules according to EN 50110‑1 "Working in a no-voltage state" in the specified sequence.
SINAMICS PERFECT HARMONY GH150 6SL3826
Operating Instructions 05/2020 13

5 safety rules
1. Disconnect the system.
Also disconnect the auxiliary circuits, for example, anti-condensation heating.
2. Secure against reconnection.
3. Verify absence of operating voltage.
4. Ground and short-circuit.
5. Provide protection against adjacent live parts.
To energize the system, apply the measures in reverse order.
2.4 Safe handling
Electric shock from external supplies
Even if the circuit breaker is open, parts of the drive can be under voltage (live) as a result of
the auxiliary voltage at the premagnetization, precharging or demagnetization transformers.
This danger is not limited to the drive, but can also occur with components that are electrically
connected to the drive (e.g. circuit breakers or isolators). Touching live parts can result in death,
serious injury and material damage
● Isolate all components that can feed voltage to the drive before commencing work.
Electric shock due to high voltages in operation
When operating this equipment very high voltages develop. Even after switching off the mains
voltage, or while the connected machine is still turning, high voltages can remain for a
prolonged length of time. Touching live parts can result in death or serious injury.
● Carefully comply with the 5 safety rules (Page 13).
● Operate the device properly.
● Service and maintain the device regularly and correctly.
Electric shock caused by induced voltage
Rotating machinery can induce dangerous high voltages and synchronous motors that are not
de-excited immediately can also pose a hazard. If the connection to the motor is not isolated or
grounded, these voltages can also remain. Touching live parts can result in death or serious
injury.
● Before opening the doors, wait until the connected machine has come to a standstill.
Safety instructions
2.4 Safe handling
SINAMICS PERFECT HARMONY GH150 6SL3826
14 Operating Instructions 05/2020

Danger to life as a result of high voltages at the capacitors and in the DC link
High voltages are still present at the capacitors of the power cell and at the DC link even after
the system has been shut down. Touching live parts can result in death or serious injury.
● A label on the drive specifies the discharge times of the DC link capacitors. Only open the
drive once these discharge times have elapsed.
● Observe the five safety rules when performing any work.
Electric shock caused by dangerous auxiliary voltages
Danger voltages are still present even after shutdown. Touching live parts can result in death
or serious injury.
● Carefully comply with the 5 safety rules.
Danger caused by arcing
Hazards caused by arcing can occur as result of the following factors, for example:
Input currents above the permissible limits, incorrectly dimensioned circuit breakers or
transformers, incorrectly connected or unconnected cables, dirt, objects that have been
forgotten, e.g. tools used for installation.
Arcing can result in death, serious injury or material damage.
● As system operator, carefully ensure that the system has been professionally designed and
dimensioned.
● Correctly connect the power cables. The maximum permissible input currents are listed in
the "Technical specifications".
● Remove contamination and dirt.
● After installation and mounting, carefully check that no objects have been left in the device.
Burns caused by fire escaping from the pressure relief flaps
Fire can escape through the pressure relief flaps if arcing occurs. Persons who are on the roof
section of the drive can suffer severe burns. Objects that are on the roof section of the drive can
catch fire or be flung into the room. Death, serious injury or material damage can result.
● Never climb on the drive. Never place any objects on the roof section of the drive.
Danger due to live stationary parts, moving or rotating parts
Contact with the parts mentioned can result in death, serious physical injury or damage to
property.
● Observe the instructions regarding installation and operation.
● Always take protective measures before touching any components.
● Do not remove any covers.
Safety instructions
2.4 Safe handling
SINAMICS PERFECT HARMONY GH150 6SL3826
Operating Instructions 05/2020 15

Risk of burns due to hot component surfaces
Certain components (e.g. the heat sink and reactor) can become very hot during operation.
These components can remain hot for a long time after operation. Severe skin injuries (burns)
can result when coming into contact with these components.
● After the device has been shut down, do not touch any hot components.
Risk of burns due to hot anti-condensation heating surface
When the temperature control limit value is reached the anti-condensation heating is switched
on. Once activated, the anti-condensation heating can generate a great deal of heat. Contact
can result in serious injury, such as skin burns.
● Ensure that the anti-condensation heating cannot be touched.
● Ensure that the anti-condensation heating is switched off before carrying out any repair or
maintenance work.
Risk of injury at places that are difficult to access
If you do not use appropriate protective equipment when working in places that are difficult to
access you are at risk of injury. For example, sharp edges and splinters can cause injuries to
the head and skin. If you carry out work in the upper section using unsuitable ladders or similar,
you can fall and injure yourself.
● Use appropriate protective equipment, especially a hard hat and gloves.
● Use suitable steps or ladders when working in the upper area.
Shutdown as a result of an incorrect residual current monitoring device
If you use a residual current monitoring device (RCD), it is possible that the residual current
monitoring device will trip in error (nuisance trip). The converter may be switched off as a result
of the protection device tripping in error.
● To minimize the risk of faulty trips, use a type-B RCD.
2.5 Electromagnetic fields in electrical power engineering installations
Electromagnetic fields are generated during operation of electrical power engineering
installations. Electromagnetic fields can interfere with electronic devices, These devices can
malfunction if electromagnetic fields are present.
Interference with pacemakers
The functioning of cardiac pacemakers could be impaired by electromagnetic fields. Death or
serious physical injury can result.
● It is therefore not permissible for people with pacemakers to stand close to the device.
Safety instructions
2.5 Electromagnetic fields in electrical power engineering installations
SINAMICS PERFECT HARMONY GH150 6SL3826
16 Operating Instructions 05/2020

Data loss
Electromagnetic fields can cause data loss to magnetic or electronic data storage media.
● Therefore, do not carry magnetic or electronic data storage media with you.
Persons responsible for plants and systems can find additional information on electromagnetic
fields under "Information for persons responsible for plants and systems (Page 18)."
2.6 Components that can be destroyed by electrostatic discharge (ESD)
ESD guidelines
Material damage caused by electrostatic discharge.
Electronic components can be destroyed in the event of improper handling, transport, storage,
and shipping.
Pack the electronic components in appropriate ESD packaging; e.g. ESD foam, ESD
packaging bags and ESD transport containers.
To protect your equipment against damage, follow the instructions given below.
● Avoid physical contact with electronic components. If it is essential that you perform work on
these components, you must wear one of the following pieces of protective gear:
– Grounded ESD wrist strap
– ESD shoes or ESD shoe grounding strips if there is also an ESD floor.
● Do not place electronic components close to data terminals, monitors or televisions.
Maintain a minimum clearance to the screen (> 10 cm).
● Electronic components should not be brought into contact with electrically insulating
materials such as plastic foil, plastic parts, insulating table supports or clothing made of
synthetic fibers.
● Bring components into contact only with ESD-compliant materials, e.g. ESD tables, ESD
surfaces, ESD packaging.
● Only carry out measurements on the components if one of the following conditions is met:
– The measuring device is grounded with a protective conductor, for example.
– The measuring head of a floating measuring device has been discharged directly before
the measurement.
The necessary ESD protective measures for the entire working range for electrostatically
sensitive devices are illustrated once again in the following drawings.
Precise instructions for ESD protective measures are specified in the standard
DIN EN 61340‑5‑1.
Safety instructions
2.6 Components that can be destroyed by electrostatic discharge (ESD)
SINAMICS PERFECT HARMONY GH150 6SL3826
Operating Instructions 05/2020 17

6HDWLQJSRVLWLRQ6WDQGLQJSRVLWLRQ6WDQGLQJVHDWLQJSRVLWLRQEEDFDIIIIIDFFHGGHG
a = Conductive floor covering 1) b = ESD furniture
c = ESD shoes or ESD shoe grounding strips 2) d = ESD clothing
e = ESD wrist strap f = Cabinet ground connection
1) Only effective in conjunction with ESD shoes or ESD shoe grounding strips
2) Only effective in conjunction with conductive floor covering
Figure 2-1 ESD information
2.7 Information for persons responsible for plants and systems
2.7.1 Proper usage
These devices are intended to be permanently installed in closed and dry rooms with a clean
atmosphere. You can find the ambient and operating temperatures to be adhered to in the
technical data. If the described environmental conditions are not observed, warranty claims
and other claims may be rejected.
Danger to life as a result of an explosion
If you operate the device in a hazardous zone, explosions can occur which can cause death,
serious injuries or material damage.
● Never operate the device in an explosive atmosphere (hazardous zone).
Danger to life when not complying with proper use of the devices
Improper use of the devices described can result in death, severe injury or material damage.
● Please observe all instructions for proper use.
The nominated person in control of an electrical installation must ensure that the following
points are observed:
● Follow the local and industry-specific safety and setup regulations. Observe the
requirements in the guidelines specified in the "Standards and regulations" section of the
"Technical data and drawings." Ensure that the specific safety and construction regulations
and the regulations for using personal protective equipment are observed during all work.
● The operating instructions and the complete product documentation are always available
when carrying out any work.
● The technical data as well as the specifications relating to the permissible installation,
connection, ambient and operating conditions are taken into account at all times.
Safety instructions
2.7 Information for persons responsible for plants and systems
SINAMICS PERFECT HARMONY GH150 6SL3826
18 Operating Instructions 05/2020

● Only qualified personnel or personnel supervised by responsible, skilled specialists are
allowed to carry out basic planning and all work on the device.
● During shipping, specific transport conditions are adhered to.
● Assembly is performed according to assembly instructions. Separate cabinet units are
connected properly (cables and busbars).
● All instructions for EMC-compatible installation, cabling, shielding, grounding, and for
adequate auxiliary power supply are to be observed.
● Commissioning is only to be performed by qualified personnel trained for that purpose in
accordance with the commissioning instructions.
● System configuration is carried out by an experienced system integrator. Additional system
components - such as circuit-breaker, transformer, cables and motor - are coordinated and
harmonized with one another for drive operation.
● The device is only operated in conjunction with the engineered components.
● Different operating modes, overloads, load cycles, and differing environmental conditions
are permitted only after special arrangement with the manufacturer.
Make use of the support and services offered by the relevant service center for planning,
installation, commissioning, and servicing work. You can find the relevant contact person under
"Service & Support (Page 123)".
2.7.2 Grounding concept
Draw-up a grounding concept and integrate the device into this concept. The grounding
concept must take into consideration national provisions and system specifics. Ensure that the
following criteria are fulfilled:
● At the installation site, the various subunits must be screwed together to establish a good
electrical connection between them.
● If shield busbars are provided, these must be connected together.
● The protective grounding conductor must be connected to the system the grounding point.
Select the highest cross-section of the protective grounding conductor from one of the
following variants:
– According to local wiring regulations
– Calculated according to IEC 60364-5-54, 543.1
– Half a phase conductor cross-section
Safety instructions
2.7 Information for persons responsible for plants and systems
SINAMICS PERFECT HARMONY GH150 6SL3826
Operating Instructions 05/2020 19

2.7.3 Installation site safety
Danger due to an unsecured installation location
This device is used in industrial power installations. Improper use, incorrect operation,
insufficient maintenance, and access by unauthorized persons can lead to accidents. The
results can be death, serious bodily injury or damage to property.
● Install the device in electrical rooms where only qualified personnel have access. If this is
not possible, then ensure that a barrier prevents uncontrolled access. Use safety fences and
appropriate signs, for example, to prevent unauthorized entry to the zone that has been
fenced off.
● Place notices that indicate that only trained personnel are allowed to operate and carry out
maintenance and repair work.
● To comply with safety regulations, equip plants and systems with additional monitoring and
protective devices. Follow technical equipment legislation and accident prevention
regulations.
Note
The drive does not have a grounding breaker at the input/output. The system operator must,
therefore, ensure that there is sufficient grounding.
2.7.4 Measures for operator protection in electromagnetic fields
The plant operator is responsible for taking the following appropriate measures (labels and
hazard warnings) to adequately protect operating personnel against any possible risk.
● Observe the relevant nationally applicable health and safety regulations or the applicable
national regulations in the country of installation. In Germany, "electromagnetic fields" are
subject to regulations BGV B11 and BGR B11 stipulated by the German statutory industrial
accident insurance institution.
● Display adequate hazard warning notices on the installation.
● Place barriers around hazardous areas.
● Take measures, e.g. using shields, to reduce electromagnetic fields at their source.
● Make sure that personnel are wearing the appropriate protective gear.
Safety instructions
2.7 Information for persons responsible for plants and systems
SINAMICS PERFECT HARMONY GH150 6SL3826
20 Operating Instructions 05/2020