Siemens 6ES7134-4JB00-0AB0 User manual

SIMATIC ET 200S distributed I/O 2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
Preface
Properties
1
Parameters
2
Diagnostics
3
Analog value representation
4
Connecting
5
SIMATIC
ET 200S distributed I/O
2AI TC ST analog electronic
module (6ES7134-4JB00-0AB0)
Manual
04/2007
A5E01076883-01

Safety Guidelines
Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage
Note the following:
WARNING
This device may only be used for the applications described in the catalog or the technical description and only
in connection with devices or components from other manufacturers which have been approved or
recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,
positioning and assembly as well as careful operation and maintenance.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Automation and Drives
Postfach 48 48
90327 NÜRNBERG
GERMANY
Ordernumber: A5E01076883-01
Ⓟ 09/2007
Copyright © Siemens AG 2007.
Technical data subject to change

2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
Manual, 04/2007, A5E01076883-01 3
Preface
Purpose of the manual
This manual supplements the ET 200S Distributed I/O System Operating Instructions.
General functions for the ET 200S are described in the
ET 200S Distributed I/O System
Operating Instructions.
The information in this document along with the operating instructions enables you to
commission the ET 200S.
Basic knowledge requirements
To understand these operating instructions you should have general knowledge of
automation engineering.
Scope of the manual
This manual applies to this ET 200S module. It describes the components that are valid at
the time of publication.
Recycling and disposal
Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable. For
environmentally compliant recycling and disposal of your electronic waste, please contact a
company certified for the disposal of electronic waste.
Additional support
If you have any questions relating to the products described in these operating instructions,
and do not find the answers in this document, please contact your local Siemens
representative.
http://www.siemens.com/automation/partner
The portal to our technical documentation for the various SIMATIC products and systems is
available at:
http://www.siemens.com/automation/simatic/portal
The online catalog and ordering system are available at:
http://www.siemens.com/automation/mall

Preface
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
4 Manual, 04/2007, A5E01076883-01
Training center
We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation
system. Please contact your regional training center or the central training center in D -
90327, Nuremberg, Germany.
Phone: [phone].
http://www.siemens.com/sitrain
Technical Support
You can reach technical support for all A&D projects
● using the support request web form:
http://www.siemens.com/automation/support-request
● Phone: + 49 180 5050 222
● Fax: + 49 180 5050 223
For more information about our technical support, refer to our Web site at
http://www.siemens.de/automation/service
Service & Support on the Internet
In addition to our documentation services, you can also make use of our comprehensive
online knowledge base on the Internet.
http://www.siemens.com/automation/service&support
There you will find:
● Our Newsletter, which constantly provides you with the latest information about your
products.
● The right documentation for you using our Service & Support search engine.
● The bulletin board, a worldwide knowledge exchange for users and experts.
● Your local contact for Automation & Drives in our contact database.
● Information about on-site services, repairs, spare parts. Lots more can be found on our
"Services" pages.

2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
Manual, 04/2007, A5E01076883-01 5
Table of contents
Preface ...................................................................................................................................................... 3
1 Properties .................................................................................................................................................. 7
1.1 2AI TC ST analog electronic module (6ES7134-4JB00-0AB0) .....................................................7
2 Parameters.............................................................................................................................................. 13
2.1 Parameters...................................................................................................................................13
2.2 Parameter description..................................................................................................................14
3 Diagnostics.............................................................................................................................................. 15
3.1 Diagnostics using LED display.....................................................................................................15
3.2 Error types....................................................................................................................................16
4 Analog value representation .................................................................................................................... 17
4.1 Introduction ..................................................................................................................................17
4.2 Analog value representation for measuring range with SIMATIC S7 ..........................................17
4.3 Measuring ranges ........................................................................................................................19
4.3.1 Measuring ranges for thermocouples ..........................................................................................19
4.3.2 Voltage measuring ranges...........................................................................................................23
4.4 Effect on analog value representation .........................................................................................24
4.4.1 Effect of the supply voltage and the operating state on analog input values ..............................24
4.4.2 Effect of the value range on the 2AI TC ST analog input ............................................................24
5 Connecting .............................................................................................................................................. 25
5.1 Connecting measuring sensors ...................................................................................................25
5.2 Connecting thermocouples ..........................................................................................................28
5.3 Wiring unused channels of the analog input modules.................................................................33
5.4 Using the shield connection .........................................................................................................33
Index........................................................................................................................................................ 35

Table of contents
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
6 Manual, 04/2007, A5E01076883-01

2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
Manual, 04/2007, A5E01076883-01 7
Properties 1
1.1 2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
Properties
● 2 inputs for thermocouple or voltage measurement
● Input ranges:
– Voltage measurement: ± 80 mV, resolution 15 bits + sign
– Thermocouples: Type E, N, J, K, L, S, R, B, T, resolution 15 bits + sign
● Isolated from the load voltage L+
● Linearization of the sensor characteristic curves
● Permissible common mode voltage 2 VACSS
● Extended temperature range from 0 to 50°C with vertical installation
General terminal assignment
Note
Terminals 4, 8, A4, A8, A3 and A7 are only available at specified terminal modules.
Terminal assignment for 2AI TC ST (6ES7134-4JB00-0AB0)
Terminal Assignment Terminal Assignment Notes
1 M
0+ 5 M 1+
2 M
0- 6 M 1-
3 M
ana 7 M ana
4 n.c. 8 n.c.
A4 AUX1 A8 AUX1
A3 AUX1 A7 AUX1
•Mn+: Measuring line positive, Channel n
•Mn-: Measuring line negative, Channel n
•Mana: Ground of the module
•n.c.: Not connected (max. 30 VDC can be connected)
•AUX1: Protective-conductor terminal or potential bus (freely usable
up to 230 VAC)

Properties
1.1 2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
8 Manual, 04/2007, A5E01076883-01
Usable terminal modules
Usable terminal modules for 2AI TC ST (6ES7134-4JB00-0AB0)
TM-E15C26-A1
(6ES7193-4CA50-
0AA0)
TM-E15C24-A1
(6ES7193-4CA30-
0AA0)
TM-E15C24-01
(6ES7193-4CB30-
0AA0)
TM-E15C23-01
(6ES7193-4CB10-
0AA0)
Spring terminal
TM-E15S26-A1
(6ES7193-4CA40-
0AA0)
TM-E15S24-A1
(6ES7193-4CA20-
0AA0)
TM-E15S24-01
(6ES7193-4CB20-
0AA0)
TM-E15S23-01
(6ES7193-4CB00-
0AA0)
Screw-type terminal
TM-E15N26-A1
(6ES7193-4CA80-
0AA0)
TM-E15N24-A1
(6ES7193-4CA70-
0AA0)
TM-E15N24-01
(6ES7193-4CB70-
0AA0)
TM-E15N23-01
(6ES7193-4CB60-
0AA0)
Fast Connect








$
$8; 
$

$

$

$8;








$$














0
0
0
3($8;
0
:LULQJH[DPSOHV
Voltage measurement as for 2AI U ST
Block diagram
$'&
0
$1$
9
/
0






3
3
08;
(76
EDFNSODQHEXV
LQWHUIDFH
FRQQHFWLRQ
%DFNSODQHEXV
Figure 1-1 Block diagram of the 2AI TC ST

Properties
1.1 2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
Manual, 04/2007, A5E01076883-01 9
2AI TC ST technical data (6ES7134-4JB00-0AB0)
Dimensions and weight
Width (mm) 15
Weight Approx. 40 g
Module-specific data
Supports isochronous operation No
Number of inputs 2
Cable length
•Shielded Max. 50 m
Parameter length 4 bytes
Address space 4 bytes
Voltages, currents, potentials
Rated load voltage L+ (from the power module) 24 VDC
•Reverse polarity protection Yes
Electrical isolation
•Between the channels and backplane bus Yes
•Between the channels and load voltage L+ Yes
•Between the channels No
•Between the channels and 24 V supply
voltage Yes
Permissible potential difference
•Between MANA and the central grounding point
(Uiso) 75 VDC / 60 VAC
•Between the inputs and MANA (UCM) 2 VACSS
Insulation tested 500 VDC
Current consumption
•From load voltage L+ Max. 30 mA
Power dissipation of the module Typically 0.6 W
Status, interrupts, diagnostics
Diagnostics function
•Group error Red "SF" LED
•Diagnostic functions readable Yes
Analog value generation
Measuring principle Integrative
Integration time/conversion time/resolution per
channel:
•Integration time can be assigned parameters Yes
•Interference frequency suppression in Hz 60 50
•Integration time in ms 16,7 20
•Basic conversion time incl. integration time in
ms 55 65
•Additional conversion time for wire break
check diagnostics in ms 20 20
•Cycle time in ms Number of active channels per module x
conversion time
•Resolution (including overrange) 15 bits plus sign

Properties
1.1 2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
10 Manual, 04/2007, A5E01076883-01
Suppression of interference, limits of error
Noise suppression for
f = n x (f1 ± 1 %), (f1 = interference frequency)
•Common-mode interference (USS)
•Common mode interference
(peak value of interference < rated value of
input range)
Min. 90 dB
Min. 70 dB
Crosstalk between the inputs Min. -50 dB
Operational limit (over the entire temperature
range, with reference to the input range)1
± 0,6 %
Basic error limit (operational limit at 25°C with
reference to input range)1
± 0,4 %
Temperature error (with reference to the input
range)
± 0.005 %/K
Linearity error (with reference to the input range) ± 0,01 %
Repeatability
(in steady state at 25°C with reference to input
range)
± 0,05 %
Data for selecting a sensor
Input range (rated value)/input resistance
•Voltage ± 80 mV/min. 1 MΩ
•Thermocouple Type E, N, J, K, L, S, R, B, T/min. 1 MΩ
Permitted input voltage (destruction limit) ± 10 V, continuous
Connection of the sensors
•For measuring voltage Supported
Characteristic curve linearization Yes, can be assigned parameters for Type E, N,
J, K, L, S, R, B, T as per IEC 584
Temperature compensation
•Internal temperature compensation Not supported
•External temperature compensation by
looping a compensating box into the
measuring circuit
Possible, one external compensating box per
channel
•External compensation by means of
temperature value obtained at an analog
module of the same ET 200S station
Yes
Smoothing of the measured values Yes, can be assigned parameters in 4 steps by
means of digital filtering
Step
None
Weak
Medium
Strong
Time constant
1 x cycle time
4 x cycle time
32 x cycle time
64 x cycle time
1 For Type N: From -150 C, Type B: from 200 °C, Type T: from -230 C

Properties
1.1 2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
Manual, 04/2007, A5E01076883-01 11
Compensation of thermocouples with a compensating box
As well as the error limits of the 2AI TC ST electronic module (see Table "Technical data
2AI TC ST (6ES7134-4JB00-0AB0)" in this chapter) you must also take the accuracy of the
compensating box into account.
Compensation of thermocouples with a Pt100 on the 2AI RTD ST
Factors affecting the accuracy of the temperature measurement
Ensure there is good thermal contact between the reference
junction and the Pt100 used for compensation.
Wiring rules
We recommend that you wire the Pt100 with a four-wire
connection.
The accuracy of the thermal resistor (Pt100) used for
compensation must be taken into account.1
Additional technical data on the
error limits of the 2AI TC
The error of the measurement input (2AI RTD ST) used for
compensation must be taken into account.1
1 In the case of thermocouples with a characteristic curve with a very shallow gradient, these errors
can lead to a major measurement discrepancy.
For the following thermocouples, this causes a limitation of the input range of the thermocouples in
which the accuracy information in the manual applies:
•Type N: -100 °C
•Type K: -230 C
•Type E: -230 C

Properties
1.1 2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
12 Manual, 04/2007, A5E01076883-01

2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
Manual, 04/2007, A5E01076883-01 13
Parameters 2
2.1 Parameters
Table 2-1 Parameters for analog input module
2AI TC ST Range of values Default setting Applicability
Group diagnostics (parameter
assignment error, internal error)
•Disable
•Enable
Disable Module
Diagnostics: Overflow/underflow •Disable
•Enable
Disable Module
Diagnostics: Wire-break check * •Disable
•Enable
Disable Channel
Smoothing •None
•Weak
•Medium
•Strong
None Channel
Comparison point •None
•RTD
None Channel
Reference junction number •None
•1 to 8
(in the case of the IM151-1
STANDARD and IM151-1 FO
STANDARD)
•1
(in the case of the IM151-1
BASIC, IM151-1 COMPACT,
IM151-1 HIGH FEATURE)
None Module
Type/range of measurement •Deactivated
•Voltage ± 80 mV
•TC-EL Type T (Cu-CuNi)
•TC-EL Type K (NiCr-Ni)
•TC-EL Type B (PtRh-PtRh)
•TC-EL Type N (NiCrSi-NiSi)
•TC-EL Type E (NiCr-CuNi)
•TC-EL Type R (PtRh-Pt)
•TC-EL Type S (PtRh-Pt)
•TC-EL Type J (Fe-Cu-Ni)
•TC-EL Type L (Fe-Cu-Ni)
TC-EL Type K (NiCr-
Ni)
Channel
* Only with thermocouples. A parameter assignment error occurs when the wire break diagnosis is enabled in the voltage
measuring range. The module does not start up.

Parameters
2.2 Parameter description
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
14 Manual, 04/2007, A5E01076883-01
2.2 Parameter description
Smoothing
The individual measured values are smoothed by digital filtering. The smoothing can be
adjusted in four steps, in which the smoothing factor k multiplied with cycle time of the
electronic module equals the time constant of the smoothing filter. The greater the
smoothing, the greater the time constant of the filter.
The following diagrams show the step response with the various smoothing factors in
relation to the number of module cycles.







     
[

[

[

[

1RQHN  :HDNN  0HGLXPN  6WURQJN 
0RGXOHF\FOHV
6WHSUHVSRQVH
Figure 2-1 Smoothing with the 2AI TC ST

2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
Manual, 04/2007, A5E01076883-01 15
Diagnostics 3
3.1 Diagnostics using LED display
LED display
1
6)
① Batch error (red)
Status and error displays
Event (LED)
SF
Cause Remedy
On No configuration or incorrect
module plugged in. No load
voltage.present There is a
diagnostic message.
Check the parameter
assignment. Check the load
voltage. Evaluate the
diagnostics.

Diagnostics
3.2 Error types
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
16 Manual, 04/2007, A5E01076883-01
3.2 Error types
Analog input module error types
Table 3-1 Error types
Error type Meaning Remedy
16D 10000:
Parameter
assignment
error
Module cannot use the
parameter for the channel:
Inserted module does not
match the one configured.
Incorrect parameter
assignment.
Correct the configuration (align
actual and set configuration).
Correct the parameter
assignment (wire break
diagnostics only parameterized
for the permitted measuring
ranges).
9D 01001: Error Internal module error
(diagnostic message at
channel 0 applies to the entire
module)
Replace the module.
7D 00111: Upper
limit exceeded
Value is above the overrange. Correct the module/final
controlling element tuning.
8D 01000: Lower
limit value
undershot
Value is below the underrange. Correct the module/final
controlling element tuning.
6D 00110:
Open circuit
Line to the encoder
interrupted.
Correct the process wiring.
21D 10101:
Reference
channel error*
Error on the reference channel Check the reference module (2
AI RTD ST).
Reference channel error is not reported if the RTD module is not parameterized in the GSD file using
the PT100 Climatic. This applies to IM151-1 HIGH FEATURE (6ES7151-1BA00-0AB0 or higher),
IM151-7 CPU and IM151-3 PROFINET IO (6ES7151-3AA00-0AB0 or higher).

2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
Manual, 04/2007, A5E01076883-01 17
Analog value representation 4
4.1 Introduction
Electronic modules with analog outputs
With the electronic module with analog inputs, continuously variable signals, such as those
occurring in temperature measurement and resistance measurement, can be acquired,
evaluated, and converted to digital values for further processing.
4.2 Analog value representation for measuring range with SIMATIC S7
Analog value representation
With the same nominal range, the digitized analog value is the same for input and output
values. Analog values are represented in two's complement.
The following table shows the analog value representation of the analog electronic modules.
Table 4-1 Analog value representation (SIMATIC S7 format)
Resolution Analog value
Bit number 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Significance of the bits S 214 2
13 2 12 2 11 2 10 2 9 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0
Sign
The sign (S) of the analog value is always in bit number 15:
● "0" → +
● "1" → –

Analog value representation
4.2 Analog value representation for measuring range with SIMATIC S7
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
18 Manual, 04/2007, A5E01076883-01
Output value
The following table shows the representation of the binary analog values and the
corresponding decimal and hexadecimal representation of the units of the analog values.
The table below shows the resolutions 11, 12, 13, and 15 bit + sign. Each analog value is
entered left aligned in the ACCU. The bits marked with "x" are set to "0".
Table 4-2 Output values (SIMATIC S7 format)
Units Analog value
Resolution in bits
Decimal Hexadecimal High byte Low byte
11+S 16 10H S 0 0 0 0 0 0 0 0 0 1 x x x x
12+S 8 8H S 0 0 0 0 0 0 0 0 0 0 1 x x x
13+S 4 4H S 0 0 0 0 0 0 0 0 0 0 0 1 x x
15 + sign 1 1H S 0 0 0 0 0 0 0 0 0 0 0 0 0 1

Analog value representation
4.3 Measuring ranges
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
Manual, 04/2007, A5E01076883-01 19
4.3 Measuring ranges
4.3.1 Measuring ranges for thermocouples
Introduction
The following tables contain the digitized analog values for the measuring ranges of the
analog input modules.
Since the binary representation of the analog values is always the same, these tables only
compare the measuring ranges with the units.
Measuring range for thermocouple: Type B
Table 4-3 SIMATIC S7 format: Type B measuring range in °C
Units Type B in °C
Decimal Hexadecimal
Range
> 2070,0 32767 7FFFH Overflow
2070,0
:
1820,1
20700
:
18201
50DCH
:
4719H
Overrange
1820,0
:
0,0
18200
:
0
4718H
:
0000H
Nominal range
-0,1
:
-120,0
-1
:
-1200
FFFFH
:
FB50H
Underrange
< -120,0 -32768 8000H Underflow

Analog value representation
4.3 Measuring ranges
2AI TC ST analog electronic module (6ES7134-4JB00-0AB0)
20 Manual, 04/2007, A5E01076883-01
Measuring range for thermocouple Type E
Table 4-4 SIMATIC S7 format: Type E measuring range in °C
Units
Type E in °C
Decimal Hexadecimal
Range
> 1200,0 32767 7FFFH Overflow
1200,0
:
1000,1
12000
:
10001
2EE0H
:
2711H
Overshoot range
1000,0
:
-270,0
10000
:
-2700
2710H
:
F574H
Nominal range
< -270,0 - 32768 8000H Underflow
Measuring range for thermocouple Type J
Table 4-5 SIMATIC S7 format: Type J measuring range in °C
Units
Type J in °C
Decimal Hexadecimal
Range
> 1450,0 32767 7FFFH Overflow
1450,0
:
1200,1
14500
:
12010
38A4H
:
2EEAH
Overrange
1200,0
:
-210,0
12000
:
-2100
2EE0H
:
F7CCH
Nominal range
< -210,0 - 32768 8000H Underflow