Siemens ARCOSKOP User manual

ARCOSKOP
English
Print No.: SPR2-250.840.01.01.02 Doc. Gen. Date: 09.05
Replaces: SPR2-250.898.01.07.02
© Siemens AG 1999
The reproduction, transmission or
use of this document or its contents
is not permitted without express
written authority. Offenders will be
liable for damages. All rights, in-
cluding rights created by patent
grant or registration of a utility
model _or_design,_are_reserved.
SP
System Manual
Trouble-Shooting-Guide

ARCOSKOP SPR2-250.840.01 Page 2 of 8 Siemens AG
System Manual Rev. 01 09.05 CS PS 24 Medical Solutions
0 - 2 Revision
Document revision level
The document corresponds to the version/revision level effective at the time of system delivery. Revi-
sions to hardcopy documentation are not automatically distributed.
Please contact your local Siemens office to order current revision levels.
Disclaimer
The installation and service of equipment described herein is to be performed by qualified personnel
who are employed by Siemens or one of its affiliates or who are otherwise authorized by Siemens or
one of its affiliates to provide such services.
Assemblers and other persons who are not employed by or otherwise directly affiliated with or autho-
rized by Siemens or one of its affiliates are directed to contact one of the local offices of Siemens or
one of its affiliates before attempting installation or service procedures.
Chapter Page Revision
all all 01

Contents 0 - 3
Siemens AG SPR2-250.840.01 Page 3 of 6 ARCOSKOP
Medical Solutions Rev. 01 09.05 CS PS 24 System Manual
1 _______Prerequisites __________________________________________________ 1 - 1
Required documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Required tools, measurement and auxiliary devices . . . . . . . . . . . . . . . . . . 1 - 1
Information regarding this document . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2
Position designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3
Information on the equivalent leakage current measurement . . . . . . . . . . . . 1 - 6
Regulations and scope for the subsidiaries . . . . . . . . . . . . . . . . . . . . . 1 - 6
Initial measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 6
Repeat measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 6
Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7
Installing/removing the covers on the support . . . . . . . . . . . . . . . . . . . . 1 - 7
Installing/removing the covers on the C-arm mounting . . . . . . . . . . . . . . . 1 - 8
Cover over the horizontal carriage . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 9
Removing the cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 9
Attaching the cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 10
Installing/removing the cover at the C-arm/I.I. side . . . . . . . . . . . . . . . . 1 - 11
Monitor trolley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 12
Installing/ removing the covers on the monitor support system . . . . . . . . . . 1 - 12
Service position for the board access of the electronics box . . . . . . . . . . . . . 1 - 13
I.I. service position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 15
Moving the I.I. into the service position . . . . . . . . . . . . . . . . . . . . . . 1 - 15
Installing the I.I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 16
2 _______Power supply adaptation ________________________________________ 2 - 1
Checking the line voltages on the monitor trolley . . . . . . . . . . . . . . . . . . . . 2 - 1
3 _______Checking the operating voltages __________________________________ 3 - 1
Low voltages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 2
Image intensifier voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 2
D41/D42 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
4 _______Operating software _____________________________________________ 4 - 1
Loading the operating software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
Backing up the system parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
Reading and storing the load counter data . . . . . . . . . . . . . . . . . . . . . . . 4 - 2
Storing the actual load counter values. . . . . . . . . . . . . . . . . . . . . . . . 4 - 2
Releasing the resetting of the load counter values . . . . . . . . . . . . . . . . . 4 - 3
Resetting the load counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3
Returning the defective POWERPHOS incl. load counter data disk . . . . . . . . 4 - 3
Storing the error log in ASCII format . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 4
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 4
5 _______Adjustments / Programming _____________________________________ 5 - 1
Page

0 - 4 Contents
ARCOSKOP SPR2-250.840.01 Page 4 of 6 Siemens AG
System Manual Rev. 01 09.05 CS PS 24 Medical Solutions
Generator adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
mAs counter adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 2
Checking the generator adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3
Dose rate adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4
Automatic dose rate adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4
Preparing the service PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4
Dose rate value to be set for the automatic dose rate adjustment . . . . . . . . . 5 - 7
23 cm I.I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7
Setting the dose rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 8
Manual dose rate adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 9
Preparation of the service PC . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 9
23 cm I.I., in the order of the operating modes . . . . . . . . . . . . . . . . . . .5 - 12
23 cm I.I., in the order of the dose rate . . . . . . . . . . . . . . . . . . . . . . .5 - 14
Measuring setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 16
Setting the dose rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 17
Note on dose rate setting for EB (EB = Single Image mode). . . . . . . . . . . .5 - 17
Calibrating the TV iris diaphragm for automatic iris diaphragm regulation (AIR) . . . .5 - 18
Measuring the minimum dose rate with the TV iris diaphragm at max. aperture . .5 - 18
Calculating the dose rate values to be programmed . . . . . . . . . . . . . . . .5 - 18
Programming the calculated dose rate values . . . . . . . . . . . . . . . . . . .5 - 19
Concluding tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 19
Checking the set dose or dose rate . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 19
Measuring setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 19
Checking the dose rate values . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 20
Setting the maximum skin dose rate . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 22
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 22
Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 22
Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 22
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 23
Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 23
Collimator, X-Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 24
Start adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 24
Full format, X-Iris open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 24
Zoom format, X-Iris open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 24
X-Iris minimum aperture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 25
Save values and end adjustment . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 25
Concluding tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 25
Collimator, slot diaphragm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 25
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 25
Disable circle mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 26
Start adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 26
Slot diaphragm, 0° position . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 26
Full format, slot diaphragm open . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 26
Zoom format, slot diaphragm open . . . . . . . . . . . . . . . . . . . . . . . . .5 - 27
Slot diaphragm closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 27
Enable circle mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 28
Save values and end adjustment . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 28
Concluding tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 28
Page

Contents 0 - 5
Siemens AG SPR2-250.840.01 Page 5 of 6 ARCOSKOP
Medical Solutions Rev. 01 09.05 CS PS 24 System Manual
Collimator display on the monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 28
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 28
Collimator display, X-Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 28
Collimator display, slot diaphragm. . . . . . . . . . . . . . . . . . . . . . . . . 5 - 30
Camera rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 34
Calibrating the area dose product measuring device . . . . . . . . . . . . . . . . . 5 - 37
CONSTANT parameters = Tw. . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 37
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 37
Checking the programmed value . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 38
Checking the accuracy of the area dose product measuring device . . . . . . . . . 5 - 39
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 39
Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 39
Dose measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 39
Calculating the area dose product . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 39
Evaluation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 40
Overview of ARCOSKOP parameters . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 41
Overview of MEMOSKOP Fast parameters . . . . . . . . . . . . . . . . . . . . . . 5 - 41
Cable module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 41
Holding force after orbital movement of C-arm . . . . . . . . . . . . . . . . . . 5 - 41
Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 41
LED D6 motor fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 41
6 _______Replacing boards / Replacing components _________________________ 6 - 1
Control board D1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
Replacement and additional work . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
Resetting the heat values after replacing board D1 . . . . . . . . . . . . . . . . . 6 - 2
Transferring the parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 2
Interface board D30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 3
Board D40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 3
Board D41/42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 3
Generator, D21 including MCB2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 3
Power supply unit D20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 4
Starting unit D115 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 4
Generator Elko buffer modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 5
POWERPHOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 6
Removing the POWERPHOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 6
Installing the POWERPHOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7
Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 8
Collimator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-9
Diamentor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-9
Replacement of the I.I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 9
Checking the temperature indicator . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 9
Dismantling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 10
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 11
Replacing the VIDEOMED DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 13
Camera rotation 0° position . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 14
Page

0 - 6 Contents
ARCOSKOP SPR2-250.840.01 Page 6 of 6 Siemens AG
System Manual Rev. 01 09.05 CS PS 24 Medical Solutions
Checks and adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 14
I.I. minivoltage supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 15
Adjusting the I.I. minivoltage supply . . . . . . . . . . . . . . . . . . . . . . . .6 - 17
Replacing the Compact optics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 19
Dismantling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 19
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 21
Basic unit control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 24
Foot switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 24
Frequency converter FV 0-400 Hz (vertical lift). . . . . . . . . . . . . . . . . . . . .6 - 27
Power supply M14, +5 V / +15 V / -15 V). . . . . . . . . . . . . . . . . . . . . . . .6 - 27
Power supply M13, +13 V Videomed DC. . . . . . . . . . . . . . . . . . . . . . . .6 - 27
I.I. Laser targeting device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 28
Replacing the MEMOSKOP Fast . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 28
Replacing the MEMOSKOP Fast . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 28
Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 28
Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 28
Loading the parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 29
Loading the language file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 29
Programming the organ menus. . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 29
Programming the MEMOSKOP serial number . . . . . . . . . . . . . . . . . . .6 - 29
Programming the licenses (Options) . . . . . . . . . . . . . . . . . . . . . . . .6 - 29
Loading a LUT file (if present) . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 30
Concluding tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 30
MULTISPOT 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 30
Monitor support system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 31
Replacing the monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 31
Replacing the keyboards, if present . . . . . . . . . . . . . . . . . . . . . . . .6 - 31
7 ______ Brakes________________________________________________________7 - 1
Braking forces / Braking torques . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
Torque, pivot brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
Measuring the orbital movement forces . . . . . . . . . . . . . . . . . . . . . . 7 - 2
Measuring the angular movement forces . . . . . . . . . . . . . . . . . . . . . . 7 - 2
Replacement of the angulation brake . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 3
Angulation brake magnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 3
Compressed air brakes of the support . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 4
Setting the movement forces in the working condition . . . . . . . . . . . . . . . 7 - 4
Friction brake at the articulated joint 2 ( center articulated joint) . . . . . . . . . . 7 - 5
Setting the movement forces in the idle state . . . . . . . . . . . . . . . . . . . 7 - 6
8 ______ Appendix, Measuring the tube current _____________________________8 - 1
9 ______ Changes to previous version _____________________________________9 - 1
Page

1 - 1
Siemens AG SPR2-250.840.01 Seite 1 von 16 ARCOSKOP
Medical Solutions Rev. 01 09.05 CS PS 24 System Manual
Prerequisites 1
Required documents 1
•ARCOSKOP circuit diagram
•Circuit diagram for monitor X2080 (if present)
•ARCOSKOP System Manual
Required tools, measurement and auxiliary devices 1
•For the laser targeting device option, if
present:
Setting Instructions / Laser targeting
device RXR2-130.032.01...
All tools, measurement and auxiliary devices with the exception
of those marked "*", are listed along with their specifications in
the STC (Service Tools Catalogue).
•Digital multimeter (e.g. "Fluke 8060 A", part no. 97 02 101)
•Oscilloscope > 50 MHz (e.g. "Fluke Combi Scope PM 3390 A",
part no. 99 00 861)
•Dose measuring device (e.g. "PTW-DIADOS", part no. 97 17 612)
•Protective ground tester (e.g. "Safety Tester Bender UNIMET 1000 ST",
part no. 51 38 727)
•Service PC with WINDOWS 95 operating system *
•Service software (see ARCOSKOP System Manual) *
•Connection cable "Service-PC - ARCOSKOP" (e.g. part no. 99 00 440)
•1 set of resolution tests (e.g. part no. 28 71 820)
•1 set of radiation filters (e.g. part no. 97 98 596)
•Centering cross (e.g. part no. 96 60 051)
•Heat conducting paste WPS (e.g. part no. 20 48 650)
•Standard service equipment *
•1 set of Allen keys *
•A 30 mm socket key (is required for adjusting the brake) *
•200 N spring scale (e.g. part no. 44 15 113)
•Torque wrench 20 Nm to 100 Nm (e.g. part no. 80 86 159)
•Torque wrench 3 Nm to 20 Nm (e.g. part no. 34 24 553)
NOTE

ARCOSKOP SPR2-250.840.01 Seite 2 von 16 Siemens AG
System Manual Rev. 01 09.05 CS PS 24 Medical Solutions
1 - 2 Prerequisites
Information regarding this document 1
These service instructions will assist you in adjusting the ARCOSKOP for routine
operation. Not every adjustment is required each time the system is serviced.
Position designations 1
The designations for the monitor trolley and the ARCOSKOP used in these instructions,
i.e. left, right, front and back, are explained in Fig.1.
Fig. 1
left
right
right
front
back
back
front
left

Prerequisites 1 - 3
Siemens AG SPR2-250.840.01 Seite 3 von 16 ARCOSKOP
Medical Solutions Rev. 01 09.05 CS PS 24 System Manual
Safety Information 1
Danger of physical injury up to death and damage to property!
You must comply with
- the product-specific safety notes in these instructions,
- the general safety notes in the instructions
TD00-000.860.01... and
- the general safety instructions according to ARTD Part 2.
In the case of non-compliance death or physical injury or damage
to property can arise.
Electrical voltage!
In the case of non-compliance death or physical injury or damage
to property can arise.
Parts conducting voltage can be touched after covers of the
system have been removed. To avoid this danger disconnect the
system from the power supply before removing covers.
For this purpose pull out the mains plug or switch the line voltage
connection of the system free of voltage and secure it against
being switched back on. In the case of necessary service work in
connection with electrical voltage, observe the general safety
notes in the instructions TD00-000.860.01...
Electrical voltage!
In the case of non-compliance death or physical injury or damage
to property can arise.
After service work on the primary circuit of the power-up module
(e.g. replacement of the power-up module or parts of it) measure
and record the equivalent system leakage current (see system fol-
der or logbook).
Danger of infection with pathogens!
In the case of non-compliance death or physical injury can arise.
This product is released for operation in operating rooms and can
be contaminated with infectious blood or other body secretions.
Avoid all contact with blood or other body secretions!
Comply strictly with the preventive measures against infectious
diseases specified in ARTD-002.731.37... !
WARNING
WARNING
WARNING
WARNING

ARCOSKOP SPR2-250.840.01 Seite 4 von 16 Siemens AG
System Manual Rev. 01 09.05 CS PS 24 Medical Solutions
1 - 4 Prerequisites
Electrical voltage!
In the case of non-compliance death or physical injury or damage
to property can arise.
After completion of all service work and after attaching all covers
of the system perform a protective ground wire test according to
ARTD-002.731.17... . The protective ground wire resistance must
not exceed 0.2 ohms.
X-ray radiation!
In the case of non-compliance death or physical injury can arise.
The radiation protection regulations must be complied with
during service work in which X-ray radiation must be released.
Keep the radiation activity as low as possible (low kV, mA, short
radiation time).
Keep your distance from the radiation source as large as possi-
ble. Radiation protection devices (lead partitions, etc.) and radia-
tion protection clothing (lead apron) must be used.
Danger of burns on hot modules or components! In the case of
non-compliance slight to medium burns, primarily on hands, can
occur.
After covers are removed modules or components (e.g. power
modules, heat sinks, magnetic brakes) that can have tempera-
tures > 50° Celsius in operation can be touched. To avoid burns
switch the system free of voltage and wait for a cooling down time
of at least 5 minutes before touching modules or components.
Electrostatic voltage!
There can be damage to property in the case of non-compliance.
Comply with the ESD protection regulations in service work.
Electrical voltage!
In the case of non-compliance death or physical injury or damage
to property can arise.
The Elko batteries of the generator and the Elkos on the generator
board remain charged for a long time even after the system is
switched off. The Elkos must be discharged before working on the
Elko batteries and before working on the generator. Switch the
switch D21.S2 into the UZ_OFF position and wait until the LEDs
D21.X22 and D21.X23 no longer light up. Then check the voltage
between the test points X109.UZ_IST and X109.ANA_GND.
The voltage must be < 0.2 V (corresponds to Uz < 20 V).
WARNING
WARNING
CAUTION
CAUTION
WARNING

Prerequisites 1 - 5
Siemens AG SPR2-250.840.01 Seite 5 von 16 ARCOSKOP
Medical Solutions Rev. 01 09.05 CS PS 24 System Manual
Danger of injury when dismantling / assembling mechanical
parts! Non-compliance can lead to minor to medium severe inju-
ries, especially to the hands!
If parts that are under mechanical stress have to be dismantled or
assembled, as for example the cover over the horizontal carriage
of the basic unit, inattention can cause injuries due to crushing,
cutting or grazing the skin, especially to the hands.
Perform the corresponding work with special care and attentiven-
ess.
Wear working gloves if necessary.
Danger of injury on mechanical parts!
Non-compliance can lead to minor up to moderately severe inju-
ries, especially to the hands!
With covers removed, you can come into contact with parts such
as flat plugs, threaded bolts, cut off cable ties or edges of com-
ponents on which, in the case of inattention, injuries can arise
due to crushing, cutting or grazing the skin, especially to the
hands.
Perform the corresponding work with special care and attentiven-
ess.
CAUTION
CAUTION

ARCOSKOP SPR2-250.840.01 Seite 6 von 16 Siemens AG
System Manual Rev. 01 09.05 CS PS 24 Medical Solutions
1 - 6 Prerequisites
Information on the equivalent leakage current measurement 1
Regulations and scope for the subsidiaries 1
Within the scope of DIN VDE0751 part 1, the equivalent leakage current test must be per-
formed.
Outside the scope of DIN VDE0751, the subsidiaries must observe the following:
(see ARTD-002.731.731.17, Safety regulations for installation and maintenance).
The legal national regulations apply to the subsidiaries. In the event that there are no exi-
sting regulations, observe the following rules in the interest of safety for customers, pati-
ents, employees and third parties, as well as the company.
Initial measurement 1
The measurement was performed at the factory and the value measured was recorded in
test protocol 1b. The measurement was performed with the line voltage and line frequency
specified in the test protocol. During start-up of the ARCOSKOP on-site, the values were
checked and remeasured and recorded if they deviated from the line voltage. The protocol
is filed in Register 9 of the System Manual and System Owner Manual,
Register 6.
Repeat measurements 1
When performing service or repair work in the primary circuit of the power supply, the
equivalent leakage current must be measured again and compared to the initial value
measured. The measurement setup must match the measurement setup for the equiva-
lent leakage current / protocol. During measurement, the ARCOSKOP must be switched
on.
When using the Bender safety tester, the tester must be set to manual measurement.
The values measured during repeat tests must not exceed the original value by more than
50%. In addition, the limit of 2 mA must not be exceeded. ARCOSKOP systems which
exceed this threshold must be serviced. The values measured are to be recorded in the
equivalent leakage current / protocol (see System Manual, Register 9).
Hand over a copy of the protocol to the customer for filing in the System Owner Manual.

Prerequisites 1 - 7
Siemens AG SPR2-250.840.01 Seite 7 von 16 ARCOSKOP
Medical Solutions Rev. 01 09.05 CS PS 24 System Manual
Covers 1
Installing/removing the covers on the support 1
•To loosen the fastening screws for the end caps on the support arms, the rubber at the
ends must be pulled out from the slot, refer to Fig. 2 to Fig. 5. After removing the Phillips
screws, press the internally located retainer a little to the inside with a thin screwdriver
and simultaneously pull the end cap out a little. After the end cap has been loosened on
both sides it can be removed.
•To remove the two-part cover of the support on the false ceiling, remove the two white
rubber plugs and unscrew the Allen screws, refer to the figure at the right above. The two
parts must be pulled apart. Take care in this case that the two internally located retaining
Fig. 2 Fig. 3
Fig. 4 Fig. 5
Electrical voltage!
See Chapter 1, Safety Information.
Prior to removing the covers, switch off the line voltage supply to
the system and secure against accidental switch-on.
Switch off the compressed air brakes, turn off the compressed air
and let it escape.
WARNING
NOTE

ARCOSKOP SPR2-250.840.01 Seite 8 von 16 Siemens AG
System Manual Rev. 01 09.05 CS PS 24 Medical Solutions
1 - 8 Prerequisites
rods remain in one half of the two covers in order to keep the space required for pulling
the halves apart small.
Installing/removing the covers on the C-arm mounting 1
•Remove the cover screws and remove both covers towards the side (Fig. 5).
•After completing the procedure, reinstall both covers in the reverse order.

Prerequisites 1 - 9
Siemens AG SPR2-250.840.01 Seite 9 von 16 ARCOSKOP
Medical Solutions Rev. 01 09.05 CS PS 24 System Manual
Cover over the horizontal carriage 1
Removing the cover 1
•Loosen the 6 mounting screws (1/Fig. 6).
•Expand the cover at the rear end in the direction of the arrow (see Fig. 2) and remove it
downwards.
•If needed disconnect the protective ground wire, the cable of the keypad (brake buttons)
and the cable of the emergency stop button.
Fig. 6 Fig. 7
Fig. 6 and Fig. 7 are examples and show the cover of the SIREMO-
BIL Iso-C.
The cover of the ARCOSKOP horizontal carriage is open to the
front in the area of the verical lifting column and has no emer-
gency stop button and only 3 brake buttons.
However, the cover of the ARCOSKOP can be removed and atta-
ched in practically the same way.
Danger of injury when dismantling / assembling mechanical
parts! Non-compliance can lead to minor up to moderately severe
injuries, especially to the hands!
The cover over the horizontal carriage is bent U-shaped and must
be pulled on the side to the outside when it is removed.
The cover is then under mechanical stress.
We recommend that you wear light working gloves to avoid inju-
ries.
NOTE
CAUTION

ARCOSKOP SPR2-250.840.01 Seite 10 von 16 Siemens AG
System Manual Rev. 01 09.05 CS PS 24 Medical Solutions
1 - 10 Prerequisites
Attaching the cover 1
•Re-fasten or connect the protective ground wire, the cable of the keypad (brake buttons)
and the cable of the emergency stop button.
•Expand the cover at the rear end (see Fig. 6) so far that as shown in Fig. 7 it lies obliquely
over the horizontal carriage in the edge 1/Fig. 7.
•Press on the top surface of the cover, without grasping the sheet metal edges, until this
slides over the lower edge of the horizontal slide. Here make sure that the cover does not
slide out from the edge (1 / Fig. 7).
•Check the operation of the emergency stop button and of the brake buttons.
•Fasten the cover with the 6 Allen screws (1/ Fig. 6).
Danger of injury when dismantling / assembling mechanical
parts! Non-compliance can lead to minor up to moderately severe
injuries, especially to the hands!
When the cover is attached and pressed down, it is under mecha-
nical stress and snaps into place over the bottom edge of the
horizontal carriage.
Expand the cover at the rear end (see Fig. 6) so far that as shown
in Fig. 7 it lies obliquely over the horizontal carriage in the edge 1/
Fig. 7.
Press on the surface on the top of the cover, without grasping the
sheet metal edges, until this slides over the lower edge of the
horizontal slide.
CAUTION

Prerequisites 1 - 11
Siemens AG SPR2-250.840.01 Seite 11 von 16 ARCOSKOP
Medical Solutions Rev. 01 09.05 CS PS 24 System Manual
Installing/removing the cover at the C-arm/I.I. side 1
•Remove the 4 fastening screws (Fig. 8). Hold the covers firmly while removing them.
•Install them in the reverse order.
Fig. 8
Danger of injury!
In the case of non-compliance death or physical injury or damage
to property can arise.
The C-arm cover contains counterbalance weights and weighs
> 10 kg.
Hold the cover firmly when installing or removing it.
Before the C-arm cover is loosened, the C-arm must be moved to
its middle orbital position.
If the C-arm covers are loosened, the C-arm must not be moved to
its orbital end positions (I.I. or POWERPHOS in the orbital end
position).
CAUTION

ARCOSKOP SPR2-250.840.01 Seite 12 von 16 Siemens AG
System Manual Rev. 01 09.05 CS PS 24 Medical Solutions
1 - 12 Prerequisites
Monitor trolley 1
Removing the covers
•Remove the upper back cover plate of the log book compartment.
•Remove the protective ground wire.
•Remove the lateral Allen screws from the lower back cover.
•Remove the protective ground wire from the cover.
Installing the covers
•Begin with the lower back cover.
•Reattach the protective ground wire for the lower cover.
•Install the cover and tighten the screws.
•Reattach the protective ground wire for the log book compartment.
•Install the cover and tighten the screws.
Installing/ removing the covers on the monitor support system 1
•Remove the screw fastening of the cover halves on the upper joint of the cover,
see arrow Fig. 9.
•Loosen the remaining cover screws and remove the two cover halves to the side.
•After taking the necessary action install the covers again in the reverse order.
Fig. 9 Monitor support system cover 1-2

Prerequisites 1 - 13
Siemens AG SPR2-250.840.01 Seite 13 von 16 ARCOSKOP
Medical Solutions Rev. 01 09.05 CS PS 24 System Manual
Service position for the board access of the electronics box 1
•The cover latch must be closed before loosening the screws (see Fig. 10).
•Remove the screws from the sides of the cover (see Fig. 10).
•Be aware of the weight added by the components attached to the rear side when opening
the latch and the service cover (see 2/Fig. 11).
•You can now lower the generator unit. Use an extension to loosen the two screws on the
upper sides (see 3/Fig. 11).
Fig. 10
Fig. 11

ARCOSKOP SPR2-250.840.01 Seite 14 von 16 Siemens AG
System Manual Rev. 01 09.05 CS PS 24 Medical Solutions
1 - 14 Prerequisites
•Cables D20, X7, X8, and X9 should be fastened to the cable clamps with a torque of
4.8 Nm. Loop the cables and attach the shield as shown in Fig. 12. Ensure that the
cables do not become crimped or torn when moving the generator.
•When routing cables in the E-box, ensure that the cover can be opened and closed
without crimping or stretching the cables or loosening the plug connection.
Fig. 12