Siemens SiPass integrated User manual

Access Control
SiPass integrated
Reference Guide
MP 2.80
A6V11144326
Smart Infrastructure
07.09.2020

Copyright
2 | 66
A6V11144326
Copyright
Technical specifications and availability subject to change without notice.
We reserve all rights in this document and in the subject thereof. By acceptance of
the document the recipient acknowledges these rights and undertakes not to
publish the document nor the subject thereof in full or in part, nor to make them
available to any third party without our prior express written authorization, nor to
use it for any purpose other than for which it was delivered to him.
Edition: 07.09.2020
Document ID: A6V11144326
© Siemens Switzerland Ltd, 2020

A6V11144326
3 | 66
Table of Contents
1 Introduction................................................................................................. 5
2 Supported Image Formats .......................................................................... 6
3 System Functions ....................................................................................... 7
4 Alarm Class .............................................................................................. 12
5 Operational Modes ................................................................................... 19
6 Manual Override ....................................................................................... 24
7 Host event tasks ....................................................................................... 28
7.1 Sources .........................................................................................................28
7.2 Targets / Commands.....................................................................................35
8 Controller Event Tasks.............................................................................. 41
8.1 Sources .........................................................................................................41
8.2 Commands ....................................................................................................49
9 ASP Trigger States ................................................................................... 54
10 ASP Effect States ..................................................................................... 62

Introduction
1
A6V11144326
5 | 66
1Introduction
Congratulations on choosing the SiPass®integrated access control and security
solution. SiPass integrated is the leading access control software on the market.
This User’s Reference Manual provides a number of reference data tables that
may assist you when assigning system functions, defining alarm classes, assigning
operational modes to points, performing manual commands, creating event tasks
and sending system messages.

Supported Image Formats
2
6 | 66
A6V11144326
2Supported Image Formats
This section lists all of the image file formats that are supported by the SiPass
integrated Photo ID and Graphics functionality.
The following table lists graphics file formats that are supported by SiPass
integrated. They may be used in any aspect of the SiPass integrated Graphics
Module, and as background images.
Supported Format
File Extension
Maximum Colors
ASCII TEXT (Version 5)
TXT
N/A
Windows Bitmap
BMP
16.7 million
CALS (Computer-aided Acquisition and Logistics
Support)
CAL
2
DCX
DCX
16.7 million
EPS
EPS
16.7 million
GEM IMG
IMG
16
GIF
GIF
256
Halo CUT
CUT
256
ICO (ICON)
ICO
16
IFF (Amiga)
IFF
16.7 million
IOCA
ICA
2
JPEG
JPG
16.7 million
LaserView
LV
2
MacPaint
MAC
2
Microsoft Windows Paint MSP
MSP
2
PCX
PCX
16.7 million
PSD (Photoshop)
PSD
16.7 million
Photo CD
PCD
16.7 million
PICT
PCT
16.7 million
Pixmap
XPM
256
SUN RASTER
RAST, RAS, IM, IM1,
IM8, IM24, IM32
16.7 million
TARGA
TGA
16.7 million
TIFF (Tagged Image File Format)
TIF
16.7 million
WMF (Windows Metafile)
WMF
16.7 million
WPG (WordPerfect Metafile)
WPG
256
Xbitmap
XBM, BM
2
AutoCAD (Document Exchange Format)
DXF
N/A

System Functions
3
A6V11144326
7 | 66
3System Functions
This section lists of all the System Functions that can be assigned to operator
groups from the Operator Group dialog.
When assigning operator privileges, you must:
1. Assign the system functions to which that operator has access.
2. Assign the appropriate level of access to that function for the operator to
adequately perform their job.
The levels of operator privilege that may be assigned to system functions are
shown in the following table.
Assigned
Privilege
Meaning
Description
<none>
(none)
The operator is not assigned any access to records relating to
system functions. They are prevented from creating, deleting,
modifying and viewing specific records or their related
attributes.
c
(create)
The operator is assigned full control of the records relating to
the system functions.
This could include privileges to create, delete, modify and
view records and their related attributes only if applicable.
e
(edit)
The operator is allowed to view and modify records relating to
specific system functions, but is prevented from creating or
deleting such records.
v
(view)
The operator is granted access to retrieve and view records
relating to specific system functions, but is prevented from
creating, deleting or modifying such records.
The following table lists the system functions that may be assigned to an operator
group together with a brief description of each function. The table also lists the
privilege levels that may be assigned for each system function.
SystemFunction
Description
Assignable
Privilege Level
Access
Configuration
Determines whether the operator should be
allowed to create, modify, delete and view
access groups and levels.
<none>, c, e, v
Additional
Preferences
Determines whether the operator can tick and
un-tick the following checkbox in the System
Preferences dialog:
Display Higher Priority Alarm, in the General
tab.
<none>, c, e, v
Advanced Reports
Determines whether the operator can view and
print advanced reports, including Image
Verification and Time and Attendance.
<none>, c, e, v
Alarm Definition
Determines whether the operator should be
allowed to create, modify, delete and view
alarm classes.
<none>, c, e, v
Alarm Queue
Provides privileges for the Alarm Queue window
and Alarm Display dialog (to allow operators to
acknowledge alarms).
<none> >, c, e, v

System Functions
3
8 | 66
A6V11144326
SystemFunction
Description
Assignable
Privilege Level
Anti-Passback Area
Provides privileges for creating, modifying,
deleting and viewing Global Anti-Passback
areas.
<none>, c, e, v
ASP Configuration
Provides privileges to launch and see Advanced
Security Programming module in SiPass
Explorer (with ‘v’ privilege), and also sets a
global privilege limit on all configured Activities.
<none>, c, e, v
ASP Operation
Provides privileges to view and edit runtime
values in flag/counter/timer runtime mode
<none>, c, e, v
Audit Trail
Determines whether the operator can or cannot
view the Active Audit Trail window.
<none>, c , e, v
Audit Trail Report
Determines whether the operator can generate
Audit Trail reports.
<none>, c, e, v
Backup
Provides privileges for the backup component
for both the Database and Audit Trail.
<none>, c
Card Reader
Configuration
Configures card readers.
<none>, c, e, v
Cardholder
Provides privileges for creating, modifying,
deleting and viewing cardholder records.
<none>, c, e, v
CCTV Command
Set Configuration
Provides privileges to add, delete, edit, or view
CCTV Command Sets.
<none>, c, e, v
CCTV Configuration
Determines whether the operator can configure
CCTV components via the SiPass interface.
<none>, c, e, v
CCTV Operation
Determines whether the operator can operate
CCTV components via the SiPass interface.
<none>, c, e, v
Components
Provides privileges for the Components dialog.
The level applied to the Components system
function will take prece-dence over other
system functions; for example, Points.
<none>, c, e, v
Credential Profile
Provides privileges to configure Credential
Profiles for cards
<none>, c, e, v
Custom Command
Configuration
Allows the operator to create additional buttons
for the menu bar that can be attached to an
executable command.
<none>, c, e, v
Custom Pages
Provides privileges to view or edit custom
pages in SiPass Explorer
<none>, c, e, v
Customized Reports
Provides privileges for customized reports in
SiPass Explorer. This privilege overwrites any
individual report privileges assigned to the
operator group.
<none>, c, e, v
Database Report
Provides privileges for the Database Reporting
component.
<none>, c
Disable Detailed AT
Logging
Provides privileges to disable Detailed Audit
Trail Logging. Requires System Preferences
and Additional Preferences.
<none>, c
Door Interlocking
Configuration
Provides privileges to configure, control and
view door interlocking functionality.
<none>, c, e, v
DVR Configuration
Determines whether the operator can configure
DVR components via the SiPass interface.
<none>, c, e, v

System Functions
3
A6V11144326
9 | 66
SystemFunction
Description
Assignable
Privilege Level
DVR Operation
Determines whether the operator can operate
DVR components via the SiPass interface.
<none>, c, e, v
Elevator Control
Provides privileges for functions contained in
the Elevator Control Module includ-ing banks,
floors, floor groups, and elevators.
<none>, c, e, v
Event Task
Provides privileges for creating, modifying,
deleting and viewing event tasks.
<none>, c, e, v
External Alarm
Monitoring
Provides privileges for the External Alarm
Monitoring function. Please note that to use this
feature, you will need access to the Unit Group
that the ACCs are a part of.
<none>, c, e, v
External System
Configuration
Provides privileges for creating, modifying,
deleting and viewing external configuration
details for OPC buses, units and points.
<none>, c, e, v
FLN Configuration
Provides privileges for the use of the Field Level
Network (FLN) Configuration tool built-in to the
SiPass integrated application. This includes
device settings and firmware download to local
devices.
<none>, c
Global Card
Management
Provides privileges for the use of the Global
Cardholder Management dialog. This includes
upload, download and full synchronization of
cardholder databases across the GCM system.
<none>, c
Graphics
Provides privileges for the Graphics Module
including site plans, drawings, symbols, and
card templates.
<none>, c, e ,v
Guard Tour
Configuration
Provides privileges for the configuration of
Guards. Tours and Tour Groups.
<none>, c, e ,v
Guard Tour
Operation
Provides privileges for the starting, stopping
and monitoring of guard tours.
<none>, c, e ,v
Holiday
Provides privileges for creating, modifying,
deleting and viewing holidays within SiPass
integrated .
<none>, c, e, v
Image Verification
Allows the operator to use the Image
Verification feature.
<none>, c
Imaging / Printing
Provides privileges for the Photo ID and Image
Verificiation , including the privilege to design
card templates.
<none>, c
Initialize
Provides privileges for performing Manual
Initialization.
<none>, c
Interactive Reports
Provides privileges to launch and see
Interactive Reports node in SiPass Explorer, as
well as allowing configuration in the Interactive
Reports dialog.
none>, c, e, v
Intrusion Area
Configuration
Provides privileges for creating, modifying,
deleting and viewing Intrusion Areas.
<none>, c, e, v
Intrusion Area
Operation
Provides privileges for performing Intrusion
related tasks. For example: assigning Isolation
privileges and arming or disarming intrusion
areas manually.
<none>, c
Log Book
Provides privileges for making log book entries.
<none>, c, e, v

System Functions
3
10 | 66
A6V11144326
SystemFunction
Description
Assignable
Privilege Level
Lookup
Provides privileges for access to the Look Up
Table in SiPass Explorer to create items in the
current table.
<none>, c, e, v
Manual Control
Provides privileges for sending manual
commands from the SiPass integrated
Workstation Client.
<none>, c
Message
Forwarding
Configuration
Provides privileges for creating, modifying,
deleting and viewing message forwarding
functions.
<none>, c, e, v
Message Queue
Operation
Provides privileges for using the features of the
Messaging Queue window.
<none>, c, e, v
Mustering Report
Provides privileges for the Mustering Report
component.
<none>, c, e, v
Offline Access
Configuration
Provides privileges for the Offline Access
Configuration component.
<none>, c, e, v
Operator
Provides privileges for creating, modifying,
deleting and viewing operator records.
<none>, c, e, v
Operator Group
Provides privileges for creating, modifying,
deleting and viewing operator groups and
operator privileges.
<none>, c, e, v
Overview
Provides privileges for viewing the Overview
window, which displays a summary of system
components.
<none>, c, e, v
PIN Assignment
Provides privileges for creating, modifying,
deleting or viewing PIN numbers assigned in
the Cardholder dialog.
<none>, c, e, v
Point
Provides privileges for creating, modifying,
deleting and viewing output, input and access
points.
<none>, c, e, v
Point Group
Provides privileges for creating, modifying and
deleting point groups.
<none>, c, e, v
Predefined Reports
Provides privileges for Predefined reports in
SiPass Explorer. This privilege overwrites any
individual report privileges assigned to the
operator group.
<none>, c, e, v
Printers
Provides privileges for configuring and
dedicating specific printers for specific functions
in SiPass integrated.
<none>, c
Profile Configuration
Provides privileges for configuring cardholder
profiles.
<none>, c, e, v
Profile Viewer
Provides access to the Profile Viewer dialog.
<none>, c
Report
Configuration
Provides privileges for the Configure Audit Trail
Reporting component.
<none>, c
Restore
Provides privileges for Database and Audit Trail
restoration.
<none>, c
See PIN
Provides privileges to view PIN Numbers in the
Cardholder dialog. If an operator does not have
this privilege assigned, the PIN number field will
be hidden.
<none>, c, e, v

System Functions
3
A6V11144326
11 | 66
SystemFunction
Description
Assignable
Privilege Level
Service Provider
Configuration
Provides privileges for creating, modifying,
deleting and viewing service provider details.
<none>, c, e, v
Smart Card
Encoding
Provides privileges for creating, modifying,
deleting and viewing the Smart Card encoding
functionality details.
<none>, c, e, v
System Preferences
Provides privileges for the configuration of
System Preferences via the System
Preferences dialog.
<none>, c , e, v
Time and
Attendance
Provides privileges for creating, viewing,
modifying and deleting details of the Time and
Attendance Interface.
<none>, c, e, v
Time Schedule
Provides privileges for creating, modifying and
deleting Time Schedules.
<none>, c, e, v
Virtual Monitor
Provides privileges for viewing live videos for IP
and DVR cameras
<none>, , v
Visitor
Provides privileges for creating, viewing,
modifying and deleting details of visitors.
<none>, c, e, v
Watchlist
Provides privileges to launch and see
Watchlists node in SiPass Explorer, as well as
allowing Watchlist data import
<none>, c, e, v
Work Group
Provides privileges for creating, modifying and
deleting work groups.
<none>, c, e, v

Alarm Class
4
12 | 66
A6V11144326
4Alarm Class
This section lists all of the possible states and their descriptions for each Alarm
Type in the Alarm Class dialog.
When creating an alarm class, you can define alarm states. For example, if you
were to create an alarm class for output points (in particular, doors with locks), you
could create two states for that class. The first state would be a restore (normal)
state when the door is locked and the second state would be an alarm state when
the door is unlocked. The event that triggers the state (door locked or unlocked) is
known as the status.
Type
Status
Description
Access
Daily code
The correct Daily Code was entered at a
keypad.
Low battery detected
A card has been used that has a low HFPU
battery and needs to be replaced, as soon
as possible.
Good access with time
stamp
A valid card was read at a card reader.
Access granted to Anti-
Passback Area
A cardholder has successfully entered an
Anti-Passback area with a valid card.
Card activates APB area
either ON
A card was used to secure an area.
Card activates APB area
either OFF
A card was used to unsecure an area.
Card activates floor
A card was used at a card reader to secure a
floor.
Card did not activate a
floor
A card was used, unsuccessfully, at a card
reader to secure a floor.
Door Time Schedule
Active
A door has reverted to normal Time
Schedule control after being manipulated by
a manual command or Event Task.
Door Free
The door latch is open and the door frame
monitor is disabled.
Door Secured
The door latch is secured and the door frame
monitor is enabled.
Tamper inactive on reader
The tamper input on a reader interface
module is inactive.
Reader online
A reader has come online.
Reader timeout
A reader has timed out after a card was
badged and PIN entry was expected.
Badge collision on reader
Not supported.
Access granted on reader
Access has been granted at an access point.
Door (Latch) locked
The door latch is secured.
No Additional Access
Mode Set
The reader has been set to No Additional
Access mode.
PIN as Card Mode Set
The reader has been set to PIN as Card
mode.
Daily Code mode set
The reader has been set to Daily Code
mode.

Alarm Class
4
A6V11144326
13 | 66
Type
Status
Description
Intrusion Control Enabled
Intrusion Control has been enabled at the
reader.
Duress
A duress alarm has been entered at an
access point.
Soft Anti-passback mode
A cardholder has failed to use their card
when leaving an area with soft anti-passback
and has tried to re-enter the same area. The
cardholder will be allowed access.
Hard Anti-passback mode
A cardholder has failed to use their card
when leaving an area with hard anti-
passback and has tried to re-enter the same
area. The cardholder will be denied access.
A card read at a disabled
readhead
A card was read at a disabled readhead.
(Disabled readhead –refers to a card reader
that has been sent a manual Disable
command).
Group error
A card, from a group (of cards) that has been
disabled, was used at a reader or is invalid
for the reader where it was used.
Alarm void card was read
A void card was read at an access point.
An invalid facility card was
read
An invalid Facility Code on a card was read
at an access point. (Each site has a site-
specific Facility Code).
Card number limit
The maximum number of cards supported by
the hardware (processor) has been reached.
An invalid PIN number
An invalid PIN (Personal Identification
Number) was entered at an access point.
Bad daily code
An invalid Daily Code was entered at a
keypad that requires a Daily Code to be
entered.
Independent service
The elevator has been placed on
independent service. (The elevator operates
independ-ently of all other elevators, usually
controlled from inside the elevator itself).
Typically initiated when being repaired.
Elevator Alarm
The emergency or alarm button within the
elevator has been activated.
Tamper active on reader
The tamper input on a reader interface
module is active.
Reader offline
A reader has gone offline.
Checksum error on reader
Not supported.
Access not granted on
reader
Access was denied at an access point.
Door (Latch) unlocked
The door latch has been unsecured.
Hard Anti-Pass back Error
A cardholder has failed to use their card
when leaving an area with soft anti-passback
and has tried to re-enter the same area. The
cardholder will be allowed access.

Alarm Class
4
14 | 66
A6V11144326
Type
Status
Description
Soft Anti Pass Back Error
A cardholder has failed to use their card
when leaving an area with hard anti-
passback and has tried to re-enter the same
area. The cardholder will be denied access.
Access Denied- Intrusion
Area Armed
Access has been denied because an
intrusion area is still armed.
Access Denied –Hard
Perimeter Violation
An access attempt has been denied, due to
an Anti-Passback violation in an area
configured with a Hard Anti-Passback mode.
Soft Perimeter Violation
A cardholder has entered a soft Anti-
Passback area that they are already within.
3 Wrong PIN entries
A cardholder has entered 3 Wrong PINs at a
reader.
Timed Re-entry Error
A cardholder has attempted to re-enter an
area (set to Timed Re-Entry Anti-Passback
mode) before their allocated re-entry time
Card not yet active
A card was presented at a reader before its
system start date has been reached.
Card Expired
A card was presented at a reader after its
system end date has expired.
Time Schedule Violation
A card was read at a reader outside the
normal scheduled time for that card.
Elevator Offline Denied
The HLI Elevator is offline.
Elevator Override Denied
The HLI Elevator is in external override.
Elevator Access Collision
The HLI Elevator is in access collision
because another access session is in
progress.
Intrusion Control Disabled
Intrusion Control has been disabled at the
reader.
SALTO Battery Low
A SALTO offline door requires a battery
change
SALTO PPD Connection
A PPD has been connected to a SALTO
offline door to update the door
Anti-Passback
Area
Capacity Full
The number of cardholders in the area
equals the defined maximum
Capacity Exceeded
The number of cardholders in the area
exceeds the defined maximum.
Capacity Not Full
The number of cardholders in the area does
not exceed the defined maximum.
Four Eyes Access Alarm
The Four Eyes Anti Passback area is in an
alarm state. The group alarm conditions are
established in the Area dialog.
Four Eyes Access Normal
The Four Eyes Anti Passback area is in a
normal state.
Capacity Empty
There are no cardholders in the area.
Workgroup Capacity Full
The number of cardholders in the area from
a Workgroup has reached the maximum for
that Workgroup.

Alarm Class
4
A6V11144326
15 | 66
Type
Status
Description
Workgroup Capacity
Exceeded
The number of cardholders in the area from
a Workgroup has exceeded the maximum for
that Workgroup.
Workgroup Capacity Not
Full
The number of cardholders in the area from
a Workgroup has not reached the maximum
for that Workgroup.
Workgroup Capacity
Empty
The number of cardholders in the area from
a Workgroup is zero.
Capacity Not Empty
The area is no longer empty.
Workgroup Capacity Not
Empty
The number of cardholders in the area from
a Workgroup is no longer zero.
Bus
Normal (bus alive)
The bus is communicating with the server.
Alarm (bus down)
The bus is not communicating with the
server.
Camera
Acknowledged
The communication link between the camera
switcher and the monitor has been restored.
Video Normal
The communication to the camera is
operating normally.
Motion Normal
The camera has acknowledged that there is
movement in the area and has raised a
normal alarm.
Video Loss
The communication link between the camera
switcher and the monitor has been lost.
Motion Alarm
The camera has detected movement and
has raised an alarm.
Device
Communication Back
The device has re-established
communication with the server.
Communication Lost
The device has lost communication with the
server.
Door
Interlocking
Interlocking Operational
Door Interlocking is enabled.
Interlocking Disabled
Door Interlocking is disabled.
Interlocking Alarm
Door Interlocking is in an alarm state.
Flag
Flag State False
The flag has been set to false
Flag State True
The flag has been set to true
Floor
Floor security on
The floor has been secured.
Floor security temp on
The Floor has been temporarily secured.
Floor security off
The Floor has been unsecured
Floor emergency stop
The Emergency Stop Button inside the
elevator has been activated.
Floor security temp off
The Floor has been temporarily unsecured.
Group
Normal
The group is in a normal state.
Alarm
The group is in an alarm state. The group
alarm conditions are established in the
Group dialog.

Alarm Class
4
16 | 66
A6V11144326
Type
Status
Description
Image
Verification
Privilege
Normal
The operator has privileges to allow or deny
entry based on visual identification of live
and database cardholder images.
Operator No IV privilege
The operator does not have privileges to
allow or deny entry based on visual
identification of live and database cardholder
images.
Input
Passback
A passback button has been activated.
Normal
The input is normal.
Door closed
The door is closed.
Fire override off
The fire override is disabled.
Battery OK
The unit’s battery output voltage is above
11.5V.
AC power back
The unit’s AC power supply has been
restored. The unit will cease to draw power
from the battery backup.
Input closed
The input has been closed.
Input Enabled
The input has changed state and is now
enabled.
Input Physically Enabled
at FLN device
The Fire Override on the device has been
enabled physically.
Input tamper or fault
cleared
The input tamper state has been cleared /
fixed.
Sintony Input Sealed
The Sintony input is inactive and the input
area could be armed.
Sintony Input Isolated
Overrides the Sintony Input Unsealed
therefore allows the area to be armed and
also disables the processing of this input in
the intrusion system.
Alarm
The input is in alarm.
Tamper
A monitored input or wire has changed state
and is either short or open circuit.
Door held
The door is being held open. (The door has
remained open after the latch time has
expired).
Door forced
The door has been forced (opened without
gaining valid access).
Fire override on
The fire override has been enabled.
Battery failed
The unit’s battery voltage has dropped below
11V. The battery circuit will be broken,
forcing a loss in communications. However,
the database memory is retained.
Battery low
The unit’s battery output voltage has
dropped below 11.5V.
AC power failed
The unit’s AC power supply has failed. The
battery backup will be switched on
automatically.

Alarm Class
4
A6V11144326
17 | 66
Type
Status
Description
Input tamper
The input or wiring has been tampered with.
Input open
The input is an open circuit.
Card limit reached
The unit’s card limit has been exceeded
Passback tamper
A supervised passback input has detected a
tamper.
Input Disabled
The input has been disabled.
Input Faulty
The input is not recognised
Input Physically disabled
at FLN device
The input has been physically disabled by
setting jumpers on the device.
Sintony Input Unsealed
The Sintony input is active and may prevent
the area from being armed (depending on
the configuration)
Intrusion Area
Intrusion Area Armed
The intrusion area has been armed.
Normal
An intrusion area that was in an alarm state
has now returned to the normal state.
Arming Action Complete
An attempt to arm a dependant intrusion
area was made. However, other areas
dependant on this area are still unarmed.
Intrusion Area Part Armed
The intrusion area has been part armed.
Intrusion Area Part Armed
B
The SPC intrusion area has been part armed
B. (SPC only)
Intrusion Area Disarmed
The intrusion area has been disarmed.
Alarm
An armed intrusion area has been violated.
Arming Failed
An attempt to arm an intrusion area has
failed.
OPC Point
Normal
The OPC Point is in a normal state.
Acked Alarm
The OPC Point is in alarm, but the alarm has
been acknowledged.
Unacked Normal
The OPC Point is in a normal state after an
alarm, but has not been acknowledged.
Disabled
The OPC Point is disabled.
Alarm
The OPC Point is in alarm.
Output
Locked
The output is secure.
Output Enabled
The output has been enabled.
Unlocked
The output is not secure.
The output is not secure.
The output has been disabled.
Output Open
Output is in an open status
Unit
Communication back
Communication between the unit and the
server is active.
Unit reset
A unit has been reset.
Unit Tamper inactive
The tamper input on a unit is inactive
Power Returned
Power has been applied to the unit.

Alarm Class
4
18 | 66
A6V11144326
Type
Status
Description
Memory Warning
The Backup Flash memory is approaching
full capacity
Communication lost
Communications between the unit and the
server has been lost.
Unit Tamper active
The tamper input on a unit is active.
Memory Full
The memory of the unit has reached
maximum capacity
Power Lost
Power has been lost from the unit.
Memory Overflow
The backup flash memory is full.
SALTO System Online
SiPass integrated is connected to the
SALTO System
SALTO System Offline
SiPass integrated is not connected to the
SALTO System

Operational Modes
5
A6V11144326
19 | 66
5Operational Modes
Operation modes are selectable only for points, not for devices. They affect how
the points operate in relation to cardholders and the system.
Type
Mode
Description
Door
Reader
Card Only
A card must be presented at the access point to
gain valid access.
Card and PIN
A card must be presented AND a matching PIN
entered at the access point to gain valid access.
Host Verification –Card
only
A card must be presented at the access point to
gain valid access; also, verification is required
by an operator that the live cardholder image
matches the stored database image.
Host Verification –Card
and PIN
A card must be presented AND a matching PIN
entered at the access point to gain valid access;
also verification is required by an operator that
the live cardholder image matches the stored
database image.
View Only –Card only
A card must be presented at the access point to
gain valid access; also, a snapshot of the
cardholder is taken as they enter and stored in
the database.
View Only –Card and PIN
A card must be presented AND a matching PIN
entered at the access point to gain valid access;
also, a snapshot of the cardholder is taken as
they enter, and stored in the database.
Double/Single Arming
A card must be presented at the access point
by a valid cardholder. A double card badge will
arm the area and a single card badge will
disarm operation for all assigned intrusion
areas.
Card Only Delayed
Reporting
This mode is used for access points for entry or
exit from defined Anti-Passback Areas.
A card must be presented at the access point to
gain valid access or exit from the Area, but
cardholder entry will not be recognized in the
Audit Trail unless the door monitor registers that
the door has opened and closed.
This means that Area counts will not increase or
decrease unless the door monitor registers the
appropriate events.
Card And PIN Delayed
Reporting
This mode is used for access points used for
entry or exit from defined Anti-Passback Areas.
A card must be presented at the access point
AND a valid PIN entered to gain valid access or
exit from the Area, but card-holder entry will not
be recog-nised in the Audit Trail unless the door
monitor registers that the door has opened and
closed.
This means that Area counts will not increase or
decrease unless the door monitor registers the
appropriate events.
Disabled Mode
The access point will be disabled.

Operational Modes
5
20 | 66
A6V11144326
Type
Mode
Description
Card + PIN Arm/Disarm
A card must be presented to gain access at the
access point. A single card badge unlocks the
door providing access without intrusion. A card
badge with a PIN unlocks the door and
simultaneously arms/disarms the intrusion area.
Press ‘1‘ then select ‘E‘ to arm the area or press
‘0‘ and then ‘E‘ to disarm the intrusion area.
Arm/Disarm Only
A valid card must be presented at the access
point as well as a PIN must be entered in order
to arm or disarm the intrusion area. Press ‘1‘and
then select ‘E‘ to arm the area; or press ‘0‘ and
then ‘E‘ to disarm.
Programmable
Authorization –Card Only
A card must be presented at the access point
for an ‘authorization started‘ event to be
generated. Access is only granted if an
‘authorization granted‘ event is received.
Programmable
Authorization –Card + PIN
A card + PIN must be presented at the access
point for an ‘authorization started’ event to be
generated, typically used as a trigger in
Advanced Security Programming. Access is
only granted if an ‘authorization granted’ event
is received.