Siemens CCAW1417-LPO Instruction sheet

Siemens AG
High-Resolution,
Day/Night Autofocus All-In-
One Camera with 22x Optical /
16x Digital Zoom
CCAW1417-LPO
Configuration Manual

Liefermöglichkeiten und technische Änderungen vorbehalten.
Data and design subject to change without notice. / Supply subject to availability.
© 2011 Copyright by Siemens AG
Wir behalten uns alle Rechte an diesem Dokument und an dem in ihm dargestellten Gegenstand vor. Der Empfänger erkennt diese Rechte
an und wird dieses Dokument nicht ohne unsere vorgängige schriftliche Ermächtigung ganz oder teilweise Dritten zugänglich machen oder
außerhalb des Zweckes verwenden, zu dem es ihm übergeben worden ist.
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our
prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.

3
Siemens AG 03.2011
Contents
1Safety .......................................................................................................5
1.1 Target readers...........................................................................................5
1.2 Work safety information ............................................................................5
1.2.1 Transport...................................................................................................5
1.2.2 Installation .................................................................................................6
1.2.3 Service and maintenance .........................................................................6
1.3 Meaning of the written warning notices ....................................................7
1.4 Meaning of the hazard symbols................................................................7
2Directives and standards .......................................................................8
3Technical data .........................................................................................9
4Details for ordering...............................................................................12
5Scope of delivery ..................................................................................12
6Description of the camera....................................................................13
6.1 Camera features .....................................................................................13
6.2 Camera parts ..........................................................................................14
6.3 Mounting parts ........................................................................................14
7System installation ...............................................................................15
7.1 Operation requirements ..........................................................................15
7.2 Installation ...............................................................................................16
7.2.1 Installation 1 (wall and mounting base) ..................................................17
7.2.2 Installation 2 (mounting base).................................................................18
7.2.3 Installation 3 (cable gland without mounting base).................................19
7.2.4 Installation 4 (optional installation box)...................................................20
8Connection ............................................................................................21
8.1 General ...................................................................................................22
8.1.1 Automatic switching between colour and B/W mode..............................22
8.1.2 RS-485 connection .................................................................................22
8.1.3 Twisted-pair video output........................................................................23
8.1.4 Alarm output............................................................................................23
8.2 Remote configuration..............................................................................24
9Camera settings ....................................................................................25
9.1 OSD main screen....................................................................................25
9.2 Main menu ..............................................................................................25
9.2.1 FOCUS....................................................................................................25
9.2.2 WB (White Balance)................................................................................26
9.2.3 AE (Auto Exposure) ................................................................................27
9.2.4 BLC / WDR (Back Light Compensation / Wide Dynamic Range)...........27
9.2.5 ALARM / MD (Motion Detection) / FD (Face Detection) .........................28
9.2.6 PRIVACY ................................................................................................28
9.2.7 SPECIAL .................................................................................................29
9.2.8 EFFECT ..................................................................................................29
9.2.9 CAMSET .................................................................................................30
10 Troubleshooting and maintenance .....................................................31
10.1 Troubleshooting ......................................................................................31
10.2 Maintenance............................................................................................31
11 Disposal .................................................................................................32

Safety
5
Siemens AG 03.2011
1 Safety
1.1 Target readers
The instructions in this document are designed only for the following target
readers:
Target readers Qualification Activity Condition of the
equipment
Start-up personnel Has appropriate
technical training with
regard to the tasks
and the products,
devices or systems to
be put in service.
Puts the device or
system which is readily
assembled and installed
on site into service.
New, readily assembled
and installed device or
modified device.
1.2 Work safety information
zRead the general safety precautions before operating the unit.
zFollow all warnings and instructions marked on the device.
zKeep this document available for reference.
zAlways pass this document on together with the product.
zPlease also take into account any additional country-specific, local safety
standards or regulations concerning project planning, operation and disposal of
the product.
Liability claim
zDo not connect the device if it is damaged or any parts are missing.
zDo not make any changes or modifications to the device that are not mentioned
in this manual and that have not been approved by the manufacturer.
zUse only spare parts and accessories that have been approved by the
manufacturer.
1.2.1 Transport
Damage during transport
zKeep the packaging material for future transportation.
zDo not expose the device to mechanical vibrations or shocks.

Safety
6
Siemens AG 03.2011
1.2.2 Installation
Damage due to unsuitable mounting location
zThe environmental conditions recommended by the manufacturer must be
observed.
zDo not operate the device in excessively dusty places.
zDo not expose the device to mechanical vibrations or shocks.
Danger of electric shock
zConnect the device only to power sources with the specified voltage. Voltage
supply requirements can be found on the type label and on the mains adapter.
zConnect the device only to a power source that complies with the Limited Power
Source requirements to EN 60950-1.
zConnect the device only to a power source that complies with SELV
requirements.
Risk of cable damage due to stress
zDo not apply tensile stress to the cable.
zMake sure that cables are not under stress, kinked or damaged.
1.2.3 Service and maintenance
Damage to the device
zDo not attempt to service this device yourself. Refer this work to qualified service
personnel.
zAlways disconnect the power cable and other cables from the main power
supply before performing maintenance.
zDisconnect the device from the mains supply before cleaning it.
zDo not use liquid cleaners or sprays that contain alcohol, spirit or ammonia.

Safety
7
Siemens AG 03.2011
1.3 Meaning of the written warning notices
The severity of a hazard is indicated by the following written warning notices.
Warning notice Type of risk
WARNING Death or severe bodily injury may result
CAUTION There is a risk of minor injuries or damage to property
IMPORTANT Malfunctioning may result
1.4 Meaning of the hazard symbols
The nature of the hazard is indicated by icons.
Caution - Dangerous area!
Caution - Dangerous electrical voltage!

Directives and standards
8
Siemens AG 03.2011
2 Directives and standards
The product complies with the requirements of the following EU directives. The EU
declaration of conformity is available from:
Siemens AG
Siemensallee 84
76181 Karlsruhe
European Directive 2004/108/EC "Electromagnetic Compatibility"
Compliance with the European Directive 2004/108/EC has been proven by testing
according to the following standard:
Emitted interference: EN 55022 Class A
Resistance to interference: EN 50130-4
CAUTION
This is a Class A device. This equipment may cause radio interference in a
residential installation. In this case the user is encouraged to perform
appropriate measures to correct the interference.

Technical data
9
Siemens AG 03.2011
3 Technical data
(
Unit: mm
)
2
1
Fig. 1 Dimensions
1 Mounting holes Ø 6.4 (4x)
2 ¼-inch 20 UNC female thread (2x)
A Front view
B Rear view
C Side view
30
15
°
°
Fig. 2 Range of camera tilting angle
Power supply
Power source 12 V DC / 24 V AC, 0.75 A, 50 Hz
Heater power 24 V AC / 0.84 A, 50 Hz
General
Image sensor ¼-inch SONY 760H EXview HAD CCD
Pixels 795 (H) x 596 (V)
Scanning system 2:1 interlace

Technical data
10
Siemens AG 03.2011
Scanning frequency 15.625 kHz (H), 50 Hz (V)
Synchronization Internal/external: line lock
Horizontal resolution Colour: 560 TV lines
B/W: 600 TV lines
Min. illumination Colour: 0.5 lux
B/W: 0.05 lux
Slow shutter: 0.001 lux
0.5 lux at F=1.6 (AGC on, 50 IRE video output)
Video output 1.0 Vpp (75 Ω, composite)
Signal/noise ratio 50 dB (AGC off)
Functions
Wide dynamic range (WDR) On/Off/Level (x512, 48 dB)
Back light compensation (BLC) Auto/Manual (Area, Level)/Off
Day/night Colour/BW/Auto/EXT
Motion detection (MD) On/Off (Area/Sensitivity setting)
Slow-speed shutter 2x – 128x
Digital noise reduction (DNR) 2D/3D
Face detection (FD) On/Off
Privacy masking (PM) Max. 16 zones, mosaic function
White balance (WB) AWB/WAWB/Indoor/Outdoor/Manual/CRS
(Colour Rolling Suppression)
Auto exposure (AE) Auto1/Auto2/Shutter Priority/Manual
Iris control Automatic
Automatic gain control (AGC) MIN/LOW/MID/HIGH (max. 30 dB)
Shutter speed Normal: 1/100.000
Title A – Z / 0 – 9
Display On/Off/Push On (DISP1/DISP2)
Brightness Adjustable in steps from 10 - 50
Sharpness Adjustable in steps from 0 - 15
Zoom presets 10
Zoom tour 1 tour / 10 presets
Alarm mode On/Off/Dwell Time
Remote configuration RS-232: Siemens B (parameter setting)
RS-485: Siemens B, S; Molynx; Pelco D, P
Bit rate BPS 2400/4800/9600/19200
Camera ID 1 – 255
Effect Sharpness, Nega/Posi, D-FLIP, Freeze, HI-
RES, 2-3 DNR
Home preset Off/Home Preset Select/Dwell Time
Lens
Focus mode Auto/Manual/Push AF
Distance 0.1 m/1.0 m/1.5 m/2.5 m/6.0 m
Total zoom 22x optical zoom, 16x digital zoom (video AF)
Focal length 3.9 – 85.8 mm

Technical data
11
Siemens AG 03.2011
Aperture F1.6 (wide-angle) – F3.7 (tele)
Angle of view Horizontal: 49.5° (wide-angle) – 2.6° (tele)
Connections and environmental conditions
Power input 2-pin cable
Video output BNC connector / TP output
Ambient temperature (operating) -30 to +50 °C
Relative humidity 0 – 96 % (non-condensing)
Ambient temperature (storage) -20 to +60 °C
Weight 1,50 kg
Protection rating IP66
TP output
Video output Adjustable: 2.0 Vpp, 2.6 Vpp, 3.2 Vpp
Frequency accentuation Adjustable: 0 dB, 6 dB, 12 dB

Details for ordering
12
Siemens AG 03.2011
4 Details for ordering
Type Part no. Designation Weight
CCAW1417-LPO S54561-C35-A1 ¼-inch Camera D/N WD AF 1,50 kg
CCAA-JB01 S54561-C51-A1 Installation box for CCAx1425/1417 0.85 kg
5 Scope of delivery
zCamera
zInstallation Manual
zSoftware and documentation on CD
zMounting parts
zTemplate
zRemote Control

Description of the camera
13
Siemens AG 03.2011
6 Description of the camera
6.1 Camera features
The high-resolution, day/night, autofocus all-in-one camera is particularly suited for
closed circuit television (CCTV) and security surveillance applications.
zAll-in-one: Autofocus camera/lens/weatherproof housing
zHigh-performance SONY 1/4-inch 760H EXview HAD CCD
z352x zooming capability (optical: 22x / digital: 16x)
zUltra-sensitivity minimum illumination of 0.5 lux at F1.6
(AGC on, 50 IRE video output)
zExcellent picture quality
zVarious picture effects
zCamera control via RS-485
zFlexible camera angle setting
zTwisted-pair video output
zRugged, compact, specially designed for indoor and outdoor installation (IP66)
zDual-power operation 12 V DC/24 V AC
CAUTION Use only certified class 2 power supply units.
Functions:
zDay/Night (D/N)
zWide dynamic range (WDR)
zDigital noise reduction (DNR)
zAuto exposure (AE)
zBack light compensation (BLC)
zDigital zoom (D-Zoom)
zDay/Night (D/N) switching
zFreeze
zDigital slow shutter (DSS)
zAutomatic white balance (AWB)
zAutomatic gain control (AGC)
zOn-screen menu (OSD)
zNegative/Positive switching (NEGA/POSI)
zE function (H/V flip, rotation)
zHigh resolution
zMotion detection and face detection
zPrivacy masking
zZoom preset and tour function
zHome preset

Description of the camera
14
Siemens AG 03.2011
IMPORTANT
The user of this camera is responsible for checking and complying with local,
state, and federal laws and statutes concerning the recording and monitoring of
audio and video signals.
6.2 Camera parts
1
23
4
5
6
7
8
9
1
0
Fig. 3 Camera parts
1 Front 6 Connection cable
2 Sunshield 7 Cable label
3 AF camera module 8 Silicagel
4 Bimetal 9 Heater
5 Mounting base 10 Mounting block (1/4-inch 20 UNC)
6.3 Mounting parts
4 Point -Drilling Position
H
ABC D E F G
Fig. 4 Mounting parts
A Torx screw T-20, 6x35 mm 4 x
B Plastic anchor Ø 8x40 mm 4 x
C Torx wrench T-20 1 x
D Allen key 2.5 mm 1 x
E Grub screw M5x5 mm 1 x
F Terminal block 7-pin
G Cable gland M22xP1.5 1 x
H Template 1 x

System installation
15
Siemens AG 03.2011
7 System installation
Installation of the camera must be performed by qualified service personnel in
accordance with all local national electrical and mechanical codes. Perform the
following steps to install the camera.
7.1 Operation requirements
Typical system configuration with DVR Typical system configuration with SIMATRIX
111
C1 C2 C10
A
B
B
234
C
111
.....
C1 C2 C10
A
B
2
4
3
C
1 Camera C1…C10 A RS485
2 Keyboard B Video
3 DVR C RS232/485
4 Monitor
1 Camera C1...C10 A RS485
2 Keyboard B Video
3 SIMATRIX C TTY
4 Monitor
When using the camera in conjunction with a video matrix switcher (SIMATRIX SYS, 648, 164) or
other telemetry equipment (different protocol) an interface converter CAC0103 is required.

System installation
16
Siemens AG 03.2011
Typical system configuration with directly controlled cameras
11
.....
C1 C2 C10
2
3
33
BBB
A
1 Camera C1..C10 A RS485
2 Keyboard B Video
3 Monitor
7.2 Installation
Mounting variations:
1234
Fig. 5 Mounting
1. Cable routing through the wall using the mounting base.
2. Cable through the conduit knockout in the mounting base.
3. Cable through the cable gland without using the mounting base.
4. Cable routing into the installation box (optional).

System installation
17
Siemens AG 03.2011
7.2.1 Installation 1 (wall and mounting base)
1. Drill the mounting holes using the drilling template (or the bottom of the
mounting base).
2. Insert the plastic anchors into the holes.
3. Connect BNC cable and the communication lines.
4. Align the plastic anchors with the holes in the mounting base.
5. Insert the torx screws (T-20) and tighten them.
6. Adjust the camera as required using the pan & tilt function. Tighten the grub
screw and the two torx screws to lock the camera in position.
Fig. 6 Installation 1
1 Wall
2 Template
3 Plastic anchor Ø 8x40 mm (4x)
4 Torx screw T-20, 6x35 mm (4x)
5 Mounting base
A Torx screw T-20
B Allen key 2.5 mm
C Cap-head screw (grub screw) M5x5 mm

System installation
18
Siemens AG 03.2011
7.2.2 Installation 2 (mounting base)
1. Drill the mounting holes using the drilling template (or the bottom of the
mounting base).
2. Insert the plastic anchors into the holes.
3. Punch out the cable entry hole in the mounting base.
4. Connect BNC cable and the communication lines.
5. Align the plastic anchors with the holes in the mounting base.
6. Insert the torx screws (T-20) and tighten them.
7. Adjust the camera as required using the pan & tilt function. Tighten the grub
screw and the two torx screws to lock the camera in position.
6
A
Fig. 7 Installation 2
1 Wall
2 Template
3 Plastic anchor Ø 8x40 mm (4x)
4 Torx screw T-20, 6x35 mm (4x)
5 Cap-head screw (grub screw) M5x5 mm
6 Mounting base
A Connection cable
B Torx screw T-20
C Allen key 2.5 mm

System installation
19
Siemens AG 03.2011
7.2.3 Installation 3 (cable gland without mounting base)
1. Loosen the grub screw using the Allen key.
2. Remove the mounting base by turning it counter-clockwise.
3. Fit the cable gland into the hole.
4. Tighten the grub screw and seal the hole using teflon tape or silicon.
5. Attach the camera to the mounting block.
14.0mm
1
2
3
4
A
Fig. 8 Installation 3
1 Cap-head screw (grub screw) M5x5 mm
2 Cable gland (M22 x P1.5)
3 Mounting base
4 Mounting block (1/4-inch 20 UNC)
A Allen key 2.5 mm

System installation
20
Siemens AG 03.2011
7.2.4 Installation 4 (optional installation box)
1. Drill the mounting holes for the installation box using the drilling template.
2. Attach the box to the wall or ceiling using the screws and plastic anchors and
O-rings included in the delivery.
3. Route the camera connection cable through the cable gland and connect the
power supply and communication lines
to the terminal block (see mounting instructions).
4. Attach the camera to the installation box using the cap-head screws (M5x20).
5. Close the box and lock the cover using the cap-head screw M5x10.
6. Adjust the camera as required using the pan & tilt function. Tighten the grub
screw and the two torx screws to lock the camera in position.
1
2
3
4
5
Fig. 9 Installation 4
1 Plastic anchor Ø 8x40 mm (4x)
2 O-ring (4x)
3 Phillips screw 5x35 mm (4x)
4 Cap-head screw M5x10 mm (1x)
5 Cap-head screw M5x20 mm (4x)
CAUTION
Protection against ingress of solid foreign objects or water
This camera is ingress-protected to IP66 only if installed in accordance with the
instructions in this manual and appropriate waterproofing is applied. For outdoor
use, the mounting base requires waterproofing.
Waterproofing should be made by qualified service personnel or system installers in accordance to the
local requirements.