Siemens SCALANCE X-200 Instruction sheet

SCALANCE X-200
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC NET
Industrial Ethernet switches
SCALANCE X-200
Configuration Manual
03/2015
C79000
-G8976-C285-06
Preface
Network topologies and
media redundancy
1
IRT communication with X-
200
2
Assignment of an IP address
3
Configuration using WBM
and CLI
4
Menus in the WBM
5
Configuration via SNMP
6
Connection to PROFINET IO
7
Downloading firmware
8
MIBs for X-200
A
Default ring ports
B

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C285-06
Ⓟ
04/2015 Subject to change
Copyright © Siemens AG 2012 - 2015.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SCALANCE X-200
Configuration Manual, 03/2015, C79000-G8976-C285-06 3
Preface
Purpose of the Configuration Manual
This manual supports you when configuring the SCALANCE X-200 Industrial Ethernet
switches. It outlines the technical options provided by a SCALANCE X-200 and describes
how to configure with Web Based Management (WBM) and the Command Line Interface
(CLI).
Overview of the technical documentation of the IE Switches X-200
The technical documentation of the X-200 product line is divided into hardware and software
and can be found in the following documents:
●
PH SCALANCE X-200 configuration manual
Software description of the X-200 product line
●
SCALANCE X-200 BA Operating Instructions
Hardware description for all product groups and general information.
You will find the documents here:
●On the data medium that ships with some products:
–Product CD / product DVD
–SIMATIC NET Manual Collection
●On the Internet pages of Siemens Industry Online Support
(http://support.automation.siemens.com/WW/view/en/33118791/133300).
Validity of this configuration manual
This manual is valid for the following firmware versions:
●SCALANCE X-200/XF-200 firmware version 5.1.0
●SCALANCE X-200IRT/XF-200IRT firmware version 5.2.0
●Primary Setup Tool as of version 4.2.0
●SNMP/OPC server as of version 6.2.1
According to the operating instructions SCALANCE X-200, this manual is valid for the
following product lines:
●SCALANCE X-200 and SCALANCE XF-200
●SCALANCE X-200IRT and SCALANCE XF-200IRT

Preface
SCALANCE X-200
4Configuration Manual, 03/2015, C79000-G8976-C285-06
Names of the devices in these operating instructions
Unless mentioned otherwise, the descriptions in these operating instructions refer to all
devices of the SCALANCE X-200 product line named above in the section on Validity.
In the remainder of the instructions, these will also be referred to as
IE switches
or also
simply as
X-200
.
Further documentation
In the system manuals "Industrial Ethernet / PROFINET Industrial Ethernet" and "Industrial
Ethernet / PROFINET passive network components", you will find information on other
SIMATIC NET products that you can operate along with the devices of this product line in an
Industrial Ethernet network.
You will find the system manuals on the Internet pages of Siemens Industry Online Support
under the following entry IDs:
●27069465 (http://support.automation.siemens.com/WW/view/en/27069465)
Industrial Ethernet / PROFINET Industrial Ethernet System Manual
●84922825 (http://support.automation.siemens.com/WW/view/en/84922825)
Industrial Ethernet / PROFINET - Passive network components System Manual
Finding information
To help orientation, there is not only a table of contents but also an Index in the Appendix.
The SIMATIC NET Glossary also provides additional help, see below.
Audience
These operating instructions are intended for persons involved in commissioning networks in
which IE switches are used.
SIMATIC NET Selection Tool
The SIMATIC NET selection tool supports you when selecting Industrial Ethernet switches
and components for Industrial Wireless Communication. You will find current information on
the Product Support pages under the following entry ID:
39134641 (http://support.automation.siemens.com/WW/view/en/39134641)

Preface
SCALANCE X-200
Configuration Manual, 03/2015, C79000-G8976-C285-06 5
Content of the Configuration Manual
This manual describes the configuration of IE switches.
You will need to configure IE switches if you want to use functions such as SNMP, loop
detection, ring redundancy or e-mail. The manual also covers the question of firmware
updates and the C-PLUG.
Before configuration, the device must be installed and connected up. You will find a
description of the necessary steps for this in the Operating Instructions.
The following table shows you which information you will find in which chapter.
Topic
Chapter
You would like to know how an IP address is struc-
tured and which options you have for assigning an IP
address to an IE switch.
Assignment of an IP address (Page 33)
You would like to configure an IE switch and require
information on the relevant CLI commands or want to
know which pages of Web Based Management you
need to edit.
Configuration using WBM and CLI (Page 37)
You want to know how to manage an IE switch with
SNMP.
Configuration via SNMP (Page 153)
You would like information about the IRT technology
with SCALANCE X-200.
IRT communication with X-200 (Page 29)
You want to know how you can use the options of
PROFINET IO for a connected IE switch.
Connection to PROFINET IO (Page 155)
You want to update the firmware.
Downloading firmware (Page 171)

Preface
SCALANCE X-200
6Configuration Manual, 03/2015, C79000-G8976-C285-06
Where to find Siemens documentation
●Article numbers
You will find the article numbers for the Siemens products of relevance here in the
following catalogs:
–SIMATIC NET - Industrial Communication / Industrial Identification, catalog IK PI
–SIMATIC - Products for Totally Integrated Automation and Micro Automation, catalog
ST 70
You can request the catalogs and additional information from your Siemens
representative. You will also find the product information in the Siemens Industry Mall at
the following address:
Auto-Hotspot
●Manuals on the Internet
You will find SIMATIC NET manuals on the Internet pages of Siemens Industry Online
Support:
Link to Customer Support (http://support.automation.siemens.com/WW/view/en)
Enter the entry ID of the relevant manual as the search item. The entry ID is specified in
the references.
As an alternative, you will find the SIMATIC NET documentation on the pages of Product
Support:
10805878 (http://support.automation.siemens.com/WW/view/en/10805878)
Go to the required product group and make the following settings:
"Entry list" tab, Entry type "Manuals / Operating Instructions"
●Manuals on the data medium
You will often find manuals of SIMATIC NET products on the data medium that ships with
many of the SIMATIC NET products.
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, solutions, machines, equipment and/or networks. They are
important components in a holistic industrial security concept. With this in mind, Siemens’
products and solutions undergo continuous development. Siemens recommends strongly
that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable
preventive action (e.g. cell protection concept) and integrate each component into a holistic,
state-of-the-art industrial security concept. Third-party products that may be in use should
also be considered. For more information about industrial security, visit
http://www.siemens.com/industrialsecurity.
To stay informed about product updates as they occur, sign up for a product-specific
newsletter. For more information, visit http://support.automation.siemens.com.

Preface
SCALANCE X-200
Configuration Manual, 03/2015, C79000-G8976-C285-06 7
SIMATIC NET glossary
Explanations of many of the specialist terms used in this documentation can be found in the
SIMATIC NET glossary.
You will find the SIMATIC NET glossary here:
●SIMATIC NET Manual Collection or product DVD
The DVD ships with certain SIMATIC NET products.
●On the Internet under the following entry ID:
50305045 (http://support.automation.siemens.com/WW/view/en/50305045)
Trademarks
The following and possibly other names not identified by the registered trademark sign ®are
registered trademarks of Siemens AG:
SIMATIC NET, SCALANCE, C-PLUG, OLM
License conditions
Note
Open source software
Read the license conditions for open source software carefully before using the product.
You will find license conditions in the following documents on the supplied data medium:
●DOC_OSS-SCALANCE-X_74.pdf
●DC_LicenseSummaryScalanceX200_76.pdf
●DC_LicenseSummaryScalanceX200IRT_76.pdf
You will find these documents on the product DVD in the following directory: /Open Source
Information

Preface
SCALANCE X-200
8Configuration Manual, 03/2015, C79000-G8976-C285-06

SCALANCE X-200
Configuration Manual, 03/2015, C79000-G8976-C285-06 9
Table of contents
Preface ................................................................................................................................................... 3
1 Network topologies and media redundancy ........................................................................................... 13
1.1 Network topologies .................................................................................................................13
1.2 Options of media redundancy.................................................................................................18
1.3 Media redundancy in ring topologies ......................................................................................19
1.4 MRP ........................................................................................................................................21
1.5 MRPD......................................................................................................................................23
1.6 HRP.........................................................................................................................................24
1.7 Redundant coupling of network segments..............................................................................25
1.8 Spanning tree, media redundancy and passive listening .......................................................27
2 IRT communication with X-200.............................................................................................................. 29
3 Assignment of an IP address................................................................................................................. 33
3.1 Introduction .............................................................................................................................33
3.2 Initial assignment of an IP address.........................................................................................35
4 Configuration using WBM and CLI ........................................................................................................ 37
4.1 Web Based Management .......................................................................................................38
4.1.1 Principle and requirements .....................................................................................................38
4.1.2 Starting the WBM and logging in ............................................................................................39
4.1.3 Simulation of the LEDs ...........................................................................................................41
4.1.4 Operator activities ...................................................................................................................42
4.2 Command Line Interface ........................................................................................................43
5 Menus in the WBM................................................................................................................................ 47
5.1 The System menu...................................................................................................................47
5.1.1 System ....................................................................................................................................47
5.1.2 I&M..........................................................................................................................................49
5.1.3 Restart & Defaults...................................................................................................................50
5.1.4 Save & Load HTTP .................................................................................................................52
5.1.5 Save & Load TFTP .................................................................................................................54
5.1.6 Version Numbers ....................................................................................................................57
5.1.7 Passwords ..............................................................................................................................59
5.1.8 Select/Set Button ....................................................................................................................60
5.1.9 Event log .................................................................................................................................62
5.1.10 C-PLUG ..................................................................................................................................64
5.2 The X-200 menu .....................................................................................................................67
5.2.1 X-200.......................................................................................................................................67
5.2.2 Fault Mask ..............................................................................................................................69
5.2.3 Ring.........................................................................................................................................71

Table of contents
SCALANCE X-200
10 Configuration Manual, 03/2015, C79000-G8976-C285-06
5.2.4 Standby .................................................................................................................................. 76
5.2.5 Procedure for redundant linking of rings................................................................................ 79
5.3 The Agent menu..................................................................................................................... 80
5.3.1 Agent...................................................................................................................................... 80
5.3.2 Ping ........................................................................................................................................ 83
5.3.3 SNMP Config ......................................................................................................................... 84
5.3.4 SNMP Trap Config................................................................................................................. 86
5.3.5 SNMP Groups........................................................................................................................ 87
5.3.6 SNMP Groups New Entry ...................................................................................................... 89
5.3.7 SNMP Config Users............................................................................................................... 90
5.3.8 SNMP Users New Entry......................................................................................................... 92
5.3.9 Agent Timeout Configuration ................................................................................................. 93
5.3.10 Event Config........................................................................................................................... 94
5.3.11 E-Mail Config.......................................................................................................................... 98
5.3.12 Time Config.......................................................................................................................... 100
5.3.13 Daylight Saving Time ........................................................................................................... 104
5.3.14 PNIO Config......................................................................................................................... 109
5.3.15 Management ACL ................................................................................................................ 111
5.4 The Switch menu ................................................................................................................. 114
5.4.1 Switch................................................................................................................................... 114
5.4.2 Ports..................................................................................................................................... 117
5.4.3 FMP...................................................................................................................................... 119
5.4.4 Cable tester.......................................................................................................................... 128
5.4.5 POF...................................................................................................................................... 129
5.4.6 FDB ...................................................................................................................................... 132
5.4.7 ARP table ............................................................................................................................. 135
5.4.8 LLDP .................................................................................................................................... 136
5.4.9 DCP...................................................................................................................................... 138
5.4.10 Loop Detection Config ......................................................................................................... 140
5.5 the Statistics menu............................................................................................................... 144
5.5.1 Statistics............................................................................................................................... 144
5.5.2 Packet size........................................................................................................................... 146
5.5.3 Packet type .......................................................................................................................... 148
5.5.4 Packet Error ......................................................................................................................... 150
6 Configuration via SNMP.......................................................................................................................153
7 Connection to PROFINET IO ...............................................................................................................155
7.1 Configuring the interrupts in STEP 7 ................................................................................... 156
7.2 MRP configuration in STEP 7 .............................................................................................. 157
7.3 Configuring the topology in STEP 7..................................................................................... 161
7.4 Configuring HRP .................................................................................................................. 163
7.5 Structure of the data records ............................................................................................... 165
7.5.1 Data record 4 ....................................................................................................................... 165
7.5.2 Data record 5 ....................................................................................................................... 166
7.5.3 Data record 0x802A ............................................................................................................. 167

Table of contents
SCALANCE X-200
Configuration Manual, 03/2015, C79000-G8976-C285-06 11
8 Downloading firmware......................................................................................................................... 171
8.1 Regular firmware download ..................................................................................................171
8.2 Loading firmware using the boot loader................................................................................172
A MIBs for X-200.................................................................................................................................... 173
A.1 Important MIB variables ........................................................................................................173
A.2 Important private MIB variables ............................................................................................175
B Default ring ports................................................................................................................................. 177
Index................................................................................................................................................... 179

Table of contents
SCALANCE X-200
12 Configuration Manual, 03/2015, C79000-G8976-C285-06

SCALANCE X-200
Configuration Manual, 03/2015, C79000-G8976-C285-06 13
Network topologies and media redundancy
1
1.1
Network topologies
Switching technology allows extensive networks to be set up with numerous nodes and
simplifies network expansion.
Which topologies can be implemented?
Bus, ring, or star topologies can be implemented with the X-200 IE switches.
Note
Make sure that the maximum permitted cable lengths for the relevant devices are not
exceeded. You will find information about the permitted cable lengths in the Technical
specifications section in the
operating instructions.
Bus topology
Figure 1-1 Electrical / optical linear topology with X-100

Network topologies and media redundancy
1.1 Network topologies
SCALANCE X-200
14 Configuration Manual, 03/2015, C79000-G8976-C285-06
Star topology
Figure 1-2 Electrical star topology. Example with X208
Figure 1-3 Star topology with X310 and X208

Network topologies and media redundancy
1.1 Network topologies
SCALANCE X-200
Configuration Manual, 03/2015, C79000-G8976-C285-06 15
Ring topology
Figure 1-4 Optical ring, example with X-200 or X-400 as redundancy manager
Figure 1-5 Electrical ring, example with X208 or X-400 as redundancy manager

Network topologies and media redundancy
1.1 Network topologies
SCALANCE X-200
16 Configuration Manual, 03/2015, C79000-G8976-C285-06
Figure 1-6 Electrical and optical ring sections, example with X206-1, X208 or X204-2 as redundancy
manager
Figure 1-7 Optical ring, example with X202-2IRT

Network topologies and media redundancy
1.1 Network topologies
SCALANCE X-200
Configuration Manual, 03/2015, C79000-G8976-C285-06 17
To increase availability, optical or electrical bus topologies made up of X-200 IE switches
with a redundancy manager can be closed to form a ring. The following IE switches can be
configured as the redundancy manager:
●SCALANCE X-200
●SCALANCE X-300
●SCALANCE X-400
●OSM / ESM version 2
The X-200 IE switches are first connected over their ring ports to form a bus. The two ends
of the line are closed to form a ring by the switch operating as redundancy manager.
When a switch is used as the redundancy manager, the ring ports are isolated from each
other if the network is operating problem-free.
The IE switch operating as redundancy manager monitors the connected bus via its ring
ports. If the connected bus is interrupted, it switches the ring ports through; in other words, it
re-establishes a functioning bus via this alternative path. Reconfiguration takes place within
0.3 seconds.
As soon as the problem has been eliminated, the original topology is restored; in other
words, the ring ports in the redundancy manager are once again disconnected from each
other.

Network topologies and media redundancy
1.2 Options of media redundancy
SCALANCE X-200
18 Configuration Manual, 03/2015, C79000-G8976-C285-06
1.2
Options of media redundancy
There are various options available to increase the network availability of an Industrial
Ethernet network with optical or electrical linear bus topologies:
●Mesh networks
●Parallel connection of transmission paths
●Closing a linear bus topology to form a ring topology

Network topologies and media redundancy
1.3 Media redundancy in ring topologies
SCALANCE X-200
Configuration Manual, 03/2015, C79000-G8976-C285-06 19
1.3
Media redundancy in ring topologies
Structure of a ring topology
Nodes in a ring topology can be external switches and/or the integrated switches of
communications modules.
To set up a ring topology with media redundancy, you bring together the two free ends of a
linear bus topology in one device. Closing the linear bus topology to form a ring is achieved
with two ports (ring ports) of a device in the ring. This device is the redundancy manager. All
other devices in the ring are redundancy clients.
Figure 1-8 Devices in a ring topology with media redundancy
The two ring ports of a device are the ports that establish the connection to its two
neighboring devices in the ring topology. The ring ports are selected and set in the
configuration of the relevant device. In STEP 7 and on the S7 Ethernet CP modules
themselves, the ring ports are indicated by an "R" after the port number.
Note
Before physically closing the ring, download the configuration of your STEP
7 project to the
individual devices.

Network topologies and media redundancy
1.3 Media redundancy in ring topologies
SCALANCE X-200
20 Configuration Manual, 03/2015, C79000-G8976-C285-06
How media redundancy works in a ring topology
When using media redundancy, the data paths between the individual devices are
reconfigured if the ring is interrupted at one point. Following reconfiguration of the topology,
the devices can once again be reached in the resulting new topology.
In the redundancy manager, the 2 ring ports are disconnected from each other if the network
is uninterrupted. This prevents circulating data frames. In terms of data transmission, the ring
topology is a linear bus topology. The redundancy manager monitors the ring topology. It
does this by sending test frames both from ring port 1 and ring port 2. The test frames run
round the ring in both directions until they arrive at the other ring port of the redundancy
manager.
An interruption of the ring can be caused by loss of the connection between two devices or
by failure of a device in the ring.
If the test frames of the redundancy manager no longer arrive at the other ring port because
of an interruption in the ring, the redundancy manager connects its two ring ports. This
substitute path once again restores a functioning connection between all remaining devices
in the form of a linear bus topology.
As soon as the interruption is eliminated, the original transmission paths are established
again, the two ring ports of the redundancy manager are disconnected and the redundancy
clients informed of the change. The redundancy clients then use the new paths to the other
devices.
The time between the ring interruption and restoration of a functional linear topology is
known as the reconfiguration time.
If the redundancy manager fails, the ring becomes a functional linear bus.
Media redundancy methods
The following media redundancy methods are supported by SIMATIC NET products:
●HRP (High Speed Redundancy Protocol)
Reconfiguration time: 0.3 seconds
●MRP (Media Redundancy Protocol)
Reconfiguration time: 0.2 seconds
The mechanisms of these methods are similar. HRP and MRP cannot be used in the ring at
the same time.