Siemens SIMATIC NET RUGGEDCOM RST2228P User manual

Edition 12/2019
Installation Manual
SIMATIC NET
Rugged Ethernet Switches
RUGGEDCOM RST2228P
For RST2228
https://www.siemens.com

SIMATIC NET
Rugged Ethernet Switches
RUGGEDCOM RST2228P
Installation Manual
For RST2228
Preface
Introduction 1
Installing the Device 2
Device Management 3
Communication Ports 4
Technical Specifications 5
Certification 6
12/2019
C79000-G8976-1403-05

Legal Information
Warning Notice System
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety
alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown be-
low are graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger
will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relat-
ing to property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the
specific task in accordance with the relevant documentation, in particular its warning notices and safety in-
structions. Qualified personnel are those who, based on their training and experience, are capable of identify-
ing risks and avoiding potential hazards when working with these products/systems.
Proper Use of Siemens Products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommend-
ed or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permis-
sible ambient conditions must be complied with. The information in the relevant documentation must be ob-
served.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publica-
tion may be trademarks whose use by third parties for their own purposes could violate the rights of the own-
er.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software de-
scribed. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the in-
formation in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Digital Industry
Process Automation
Postfach 48 48
90026 NÜRNBERG
GERMANY
© 12/2019 Subject to Change Copyright © Siemens 2019
All rights reserved

Table of Contents
Preface ............................................................................................................................................ v
Related Documents ................................................................................................................. v
Accessing Documentation ....................................................................................................... v
Disclaimer of Liability .............................................................................................................. v
Registered Trademarks ............................................................................................................ v
Training .................................................................................................................................. vi
Customer Support .................................................................................................................. vi
Contacting Siemens ............................................................................................................... vii
1 Introduction ........................................................................................................................... 1
1.1 Feature Highlights ................................................................................................. 1
1.2 Description ............................................................................................................ 2
1.3 Required Tools and Materials ................................................................................. 6
1.4 Decommissioning and Disposal ............................................................................. 6
1.5 Cabling Recommendations .................................................................................... 7
1.5.1 Protection On Twisted-Pair Data Ports .................................................................... 7
1.5.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations ...................................... 7
1.5.3 Supported Fiber Optic Cables ................................................................................ 8
2 Installing the Device ............................................................................................................. 9
2.1 General Procedure ................................................................................................. 9
2.2 Unpacking the Device ......................................................................................... 10
2.3 Mounting the Device ........................................................................................... 10
2.3.1 Mounting the Device to a Rack ............................................................................ 11
2.3.2 Mounting the Device to a Panel .......................................................................... 12
2.4 Connecting the Failsafe Alarm Relay .................................................................... 13
2.5 Connecting Power ............................................................................................... 15
2.5.1 Connecting High AC/DC Power ............................................................................ 15
2.5.2 Connecting Low DC Power .................................................................................. 18
2.5.3 Connecting External PoE Power ........................................................................... 20
2.5.4 Wiring Examples .................................................................................................. 22
3 Device Management ........................................................................................................... 25
3.1 Connecting to the Device .................................................................................... 25
3.2 Configuring the Device ........................................................................................ 26
3.3 Inserting/Removing the CLP ................................................................................. 26
4 Communication Ports .......................................................................................................... 29
4.1 SFP Transceivers .................................................................................................. 29
4.2 PoE Ports ............................................................................................................. 31
RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05 iii

Table of Contents
4.3 Available Modules ............................................................................................... 31
4.4 Installing/Removing Modules ............................................................................... 33
5 Technical Specifications ...................................................................................................... 35
5.1 Power Supply Specifications ................................................................................ 35
5.2 PoE Power Supply Specifications .......................................................................... 35
5.3 Failsafe Alarm Relay Specifications ...................................................................... 36
5.4 Supported Networking Standards ........................................................................ 36
5.5 Operating Environment ....................................................................................... 36
5.6 Mechanical Specifications .................................................................................... 37
5.7 Dimension Drawings ........................................................................................... 37
6 Certification ......................................................................................................................... 41
6.1 Approvals ............................................................................................................ 41
6.1.1 CSA ..................................................................................................................... 41
6.1.2 European Union (EU) .......................................................................................... 41
6.1.3 FCC ..................................................................................................................... 42
6.1.4 FDA/CDRH ........................................................................................................... 43
6.1.5 ISED .................................................................................................................... 43
6.1.6 TÜV SÜD ............................................................................................................. 43
6.1.7 RoHS ................................................................................................................... 43
6.1.8 Other Approvals .................................................................................................. 44
6.2 EMC and Environmental Type Tests ..................................................................... 44
iv RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05

Preface
This guide describes the RUGGEDCOM RST2228P. It describes the major features of
the device, installation, commissioning and important technical specifications.
It is intended for use by network technical support personnel who are responsible
for the installation, commissioning and maintenance of the device. It is also recom-
mended for use by network and system planners, system programmers, and line
technicians.
Related Documents
Other documents that may be of interest include:
•RUGGEDCOM RST2228 Configuration Manual [https://support.industry.siemen-
s.com/cs/ww/en/view/109755340]
•RUGGEDCOM Modules Catalog for RST2228, RST2228P [https://support.indus-
try.siemens.com/cs/ww/en/view/109752858]
Accessing Documentation
The latest user documentation for RUGGEDCOM RST2228P is available online at
https://support.industry.siemens.com. To request or inquire about a user document,
contact Siemens Customer Support.
Disclaimer of Liability
Siemens has verified the contents of this document against the hardware and/or soft-
ware described. However, deviations between the product and the documentation
may exist.
Siemens shall not be liable for any errors or omissions contained herein or for conse-
quential damages in connection with the furnishing, performance, or use of this ma-
terial.
The information given in this document is reviewed regularly and any necessary cor-
rections will be included in subsequent editions. We appreciate any suggested im-
provements. We reserve the right to make technical improvements without notice.
Registered Trademarks
RUGGEDCOM™ and ROS™ are trademarks of Siemens AG.
RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05 v

Preface
Training
Other designations in this manual might be trademarks whose use by third parties
for their own purposes would infringe the rights of the owner.
Training
Siemens offers a wide range of educational services ranging from in-house training
of standard courses on networking, Ethernet switches and routers, to on-site cus-
tomized courses tailored to the customer's needs, experience and application.
Siemens' Educational Services team thrives on providing our customers with the es-
sential practical skills to make sure users have the right knowledge and expertise to
understand the various technologies associated with critical communications net-
work infrastructure technologies.
Siemens' unique mix of IT/Telecommunications expertise combined with domain
knowledge in the utility, transportation and industrial markets, allows Siemens to
provide training specific to the customer's application.
For more information about training services and course availability, visit https://-
www.siemens.com or contact a Siemens Sales representative.
Customer Support
Customer support is available 24 hours, 7 days a week for all Siemens customers.
For technical support or general information, contact Siemens Customer Support
through any of the following methods:
Online
Visit http://www.siemens.com/automation/support-request to submit a
Support Request (SR) or check on the status of an existing SR.
Telephone
Call a local hotline center to submit a Support Request (SR). To locate a lo-
cal hotline center, visit https://w3.siemens.com/aspa_app/?lang=en.
Mobile App
Install the Industry Online Support app by Siemens AG on any Android,
Apple iOS or Windows mobile device and be able to:
• Access Siemens' extensive library of support documentation, includ-
ing FAQs and manuals
• Submit SRs or check on the status of an existing SR
• Contact a local Siemens representative from Sales, Technical Support,
Training, etc.
• Ask questions or share knowledge with fellow Siemens customers
and the support community
vi RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05

Preface
Contacting Siemens
Contacting Siemens
Address Siemens AG
Industry Sector
300 Applewood Crescent
Concord, Ontario
Canada, L4K 5C7
Telephone Toll-free: 1 888 264 0006
Tel: [phone]
Fax: [phone]
E-Mail [email protected]
Web https://www.siemens.com
RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05 vii

Preface
Contacting Siemens
viii RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05

Introduction 1
The RUGGEDCOM RST2228P is a utility grade, fully managed, industrial Ethernet
switch designed to operate reliably in harsh environments. With a rugged metal en-
closure and an optional conformal coating, the RUGGEDCOM RST2228P provides a
high level of immunity to electromagnetic interference and heavy electrical surges,
and can withstand temperatures between -40 and 85 °C (-40 and 185 °F).
Highly modular, the RUGGEDCOM RST2228P switch supports up to 24 PoE ports and
28 optical interfaces with data transfer rates of 10/100/1000 Mbit/s. Four ports in-
clude data transfer rates of 10000Mbit/s. This makes it the ideal industry-standard
switch for constructing electrical and/or optical line, ring and star topologies.
The RUGGEDCOM RST2228P switch is supported by RUGGEDCOM RST2228P, which
provides advanced Layer 2 networking functions, and advanced cyber security fea-
tures.
1.1 Feature Highlights
Power over Ethernet (PoE)
• Supports up to 24 PoE ports with data transfer rates of 10/100/1000 Mbit/s
• Supports 4-pair or 60 W/port
• Supports up to 120 W of PoE power/module (e.g. two 60 W ports or four 30 W
ports)
• Supports up to maximum 500 W/system
• Data and power over a single Ethernet cable
• No mid-span patch panel required
• Fully compatible with IEEE 802.3af and IEEE 802.3at powered devices
• Auto-sensing ports that provide power only to PoE end devices
• Power to port is turned off if cables are removed
Extreme Flexibility
• Support for up to a total of 28 non-blocking ports (six 4-port modules and four
fixed ports)
• Mixture of fiber optic or copper Gigabit ports with up to 28 Gig Ethernet ports,
including 4 ports capable of 10 Gigabits.
• Galvanized steel and aluminum construction
RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05 1

Introduction
1.2Description
Compact 1U Form Factor
• Space-saving design
Front Loading Modular Design
• Allows for simple, cost effective in-field servicing and upgrading
Dual Redundant Smart Power Supplies
• HI voltage AC/DC: 88-300 VDC or 85-264 VAC
• LO voltage DC: 10.5-15 VDC, 13-36 VDC or 36-72 VDC
• Smart power supplies able to detect loss of input voltage
Reliability in Harsh Environments
• Immunity to EMI and heavy electrical surges
• Zero-Packet-Loss Technology
• Supports Siemens FastConnect RJ45 Cabling System
• -40 to 85 °C (-40 to 185 °F) operating temperature (fan-less)
• Conformal coated printed circuit boards (optional)
1.2 Description
The RUGGEDCOM RST2228P features various ports, controls and indicator LEDs for
connecting, configuring and troubleshooting the device.
2RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05

Introduction
1.2Description
Orientation Options
The RUGGEDCOM RST2228P is available in one of two options:
•Option 1
Status panel, alarm LED, ACO Button, CLP port and USB console port are located
on the front panel.
9
2
1
3
4
5
6
7
8
1 Status Panel
2 ACO Button
3 CLP Port
4 USB Console Port
5 PoE Power and Failsafe Alarm Relay Terminal Block
6 Power Terminal Block
7 SFP/SFP+ Transceiver Sockets
8 Media Modules
9 Chassis Ground Terminal
Figure1.1 RUGGEDCOM RST2228P (Front Panel Orientation)
RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05 3

Introduction
1.2Description
•Option 2
Status panel, alarm LED, ACO Button, CLP port and USB console port are located
on the rear panel.
9
2
1
3
4
5
6
7
8
1 Status Panel
2 ACO Button
3 CLP Port
4 USB Console Port
5 PoE Power and Failsafe Alarm Relay Terminal Block
6 Power Terminal Block
7 SFP/SFP+ Transceiver Sockets
8 Media Modules
9 Chassis Ground Terminal
Figure1.2 RUGGEDCOM RST2228P (Rear Panel Orientation)
Key Features
Status Panel The status panel displays the real-time status of the device.
Six module slot locators indicate the physical location of each media
module in relation to the available chassis slots. Module ports are
numbered from left to right when installed in the chassis. A dedicat-
ed LED is assigned to each module port.
4RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05

Introduction
1.2Description
1
4
3
5
6
7
2
1 LEDs for 10GBase SFP+ Transceivers (Slot 0)
2 Module Slot Locators
3 LEDs for Module Ports
4 Alarm Status LED
5 Power Supply Status LEDs
6 PoE Status LED
7 ACO Button
Figure1.3 Status Panel
LED State Description
Solid
(Green)
Link detected
Solid
(Yellow)
Link detected and PoE established
Blinking Link activity
P{num-
ber}
Off No link detected
Solid An alarm condition existsA
Off No active alarm conditions exist
Solid The power source is supplying power to the
device
PS1/PS2
Off The power source is not supplying power to
the device
Solid The PoE power source is supplying power
to the device
PoE
Off The PoE power source is not supplying
power to the device
USB Console Port The serial console port is for interfacing directly with the device and
accessing initial management functions. For information about con-
necting to the device via the serial console port, refer to "Connect-
ing to the Device (Page 25)".
Alarm Indicator LED The alarm indicator LED illuminates when an alarm condition exists.
Pressing the Alarm Cut-Off (ACO) button clears the alarm(s).
Removable Media The device features sockets for up to four SFP/SFP+ transceivers and
slots for up to six removable media modules. For more information,
refer to "Communication Ports (Page 29)".
RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05 5

Introduction
1.3Required Tools and Materials
PoE Power and Failsafe Alarm
Relay
Latches to default state when a power disruption or other alarm
condition occurs. For more information, refer to:
•"Connecting the Failsafe Alarm Relay (Page 13)"
•"Failsafe Alarm Relay Specifications (Page 36)"
•"Connecting External PoE Power (Page 20)"
Power Supply Terminal Block A pluggable terminal block. For more information, refer to:
•"Connecting Power (Page 15)"
•"Power Supply Specifications (Page 35)"
Chassis Ground Terminal Protects the device from power surges and accumulated static elec-
tricity. For information about grounding the device, refer to "Con-
necting Power (Page 15)".
1.3 Required Tools and Materials
The following tools and materials are required to install the RUGGEDCOM RST2228P:
Tools/Materials Purpose
AC/DC power cord For connecting power to the device. For the re-
quired. To determine the proper wire gage, refer
to "Power Supply Specifications (Page 35)".
Lightning protector For protecting the device from harmful electrical
strikes.
Flathead screwdriver For removing or installing modules and terminal
blocks.
Torx T10 screwdriver For removing or installing modules.
Phillips screwdriver For removing or installing terminal blocks.
8 x M6 or #10-32 screws For mounting the device to a panel.
8 x M6 or #10-32 screws For mounting the device to a rack.
Braided or equivalent ground wire For grounding the device to safety Earth.
1.4 Decommissioning and Disposal
Proper decommissioning and disposal of this device is important to prevent malicious
users from obtaining proprietary information and to protect the environment.
Decommissioning
This device may include sensitive, proprietary data. Before taking the device out of
service, either permanently or for maintenance by a third-party, make sure it has
been fully decommissioned.
For more information, refer to the associated Configuration Manual.
6RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05

Introduction
1.5Cabling Recommendations
Recycling and Disposal
For environmentally friendly recycling and disposal of this device and related acces-
sories, contact a facility certified to dispose of waste electrical and electronic equip-
ment. Recycling and disposal must be done in accordance with local regulations.
1.5 Cabling Recommendations
Siemens recommends using SIMATIC NET industrial Ethernet shielded cables for all
Ethernet ports.
1.5.1 Protection On Twisted-Pair Data Ports
All copper Ethernet ports on RUGGEDCOM products include transient suppression
circuitry to protect against damage from electrical transients and conform with IEC
61850-3 and IEEE 1613 Class 1 standards. This means that during a transient electri-
cal event, communications errors or interruptions may occur, but recovery is auto-
matic.
Siemens also does not recommend using copper Ethernet ports to interface with de-
vices in the field across distances that could produce high levels of ground potential
rise (i.e. greater than 2500 V), during line-to-ground fault conditions.
1.5.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations
The IEEE 802.3ab Gigabit Ethernet standard defines 1000 Mbit/s Ethernet commu-
nications over distances of up to 100 m (328 ft) using all 4 pairs in category 5 (or
higher) balanced, unshielded twisted-pair cabling. For wiring guidelines, system de-
signers and integrators should refer to the Telecommunications Industry Association
(TIA) TIA/EIA-568-A wiring standard that characterizes minimum cabling performance
specifications required for proper Gigabit Ethernet operation. For reliable, error-free
data communication, new and pre-existing communication paths should be verified
for TIA/EIA-568-A compliance.
The following table summarizes the relevant cabling standards:
Cabling
Category
1000Base-
TX Compliant
Required Action
< 5 No New wiring infrastructure required.
5 Yes Verify TIA/EIA-568-A compliance.
5e Yes No action required. New installations should
be designed with Category 5e or higher.
6 Yes No action required.
> 6 Yes Connector and wiring standards to be determined.
RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05 7

Introduction
1.5.3Supported Fiber Optic Cables
Follow these recommendations for copper data cabling in high electrical noise envi-
ronments:
• Data cable lengths should be as short as possible, preferably 3 m (10 ft) in
length. Copper data cables should not be used for inter-building communica-
tions.
• Power and data cables should not be run in parallel for long distances, and
should be installed in separate conduits. Power and data cables should intersect
at 90° angles when necessary to reduce inductive coupling.
• Shielded/screened cabling can be used when required. Care should be taken to
avoid the creation of ground loops with shielded cabling.
1.5.3 Supported Fiber Optic Cables
The following fiber optic cable types are supported under the stated conditions.
Distance (m)Cable Type Wavelength (nm) Modal Band-
width (MHz·km) 100Base-FX 1000Base-SX 10GBase-SR
850 200 — 275 33OM1 (62.5/125)
1300 500 2000 — —
850 500 — 550 82OM2 (50/125)
1300 500 2000 — —
850 1500 — 550 300OM3 (50/125)a
1300 500 2000 — —
850 3500 — 550 400OM4 (50/125)a
1300 500 2000 — —
aLaser optimized.
8RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05

Installing the Device 2
This chapter describes how to install the device, including mounting the device, con-
necting power, and connecting the device to the network.
DANGER
Electrocution hazard – risk of serious personal injury and/or damage to equip-
ment.
Before performing any maintenance tasks, make sure all power to the device has
been disconnected and wait approximately two minutes for any remaining energy
to dissipate.
WARNING
Radiation hazard – risk of serious personal injury.
This product may contain a laser system and is classified as a CLASS 1 LASER PROD-
UCT. Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
NOTICE
This product contains no user-serviceable parts. Attempted service by unauthorized
personnel shall render all warranties null and void.
Changes or modifications not expressly approved by Siemens AG could invalidate
specifications, test results, and agency approvals, and void the user's authority to
operate the equipment.
NOTICE
This product should be installed in a restricted access location where access can only
be gained by authorized personnel who have been informed of the restrictions and
any precautions that must be taken. Access must only be possible through the use of
a tool, lock and key, or other means of security, and controlled by the authority re-
sponsible for the location.
2.1 General Procedure
The general procedure for installing the device is as follows:
NOTICE
The user is responsible for the operating environment of the device, including main-
taining the integrity of all protective conductor connections and checking equip-
RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05 9

Installing the Device
2.2Unpacking the Device
ment ratings. Make sure to review all operating and installation instructions before
commissioning or performing maintenance on the device.
1. Review the relevant certification information for any regulatory require-
ments.
For more information, refer to "Approvals (Page 41)".
2. Review the RUGGEDCOM RST2228P Modules Catalog for special installation
or regulatory requirements related to the modules installed in the device.
For more information, refer to "Related Documents (Page v)".
3. Unpack and inspect the device.
For more information, refer to "Unpacking the Device (Page 10)".
4. Mount the device.
For more information, refer to "Mounting the Device (Page 10)".
5. Connect the failsafe alarm relay.
For more information, refer to "Connecting the Failsafe Alarm Relay (Page
13)".
6. Connect power to the device and ground the device to safety Earth.
For more information, refer to "Connecting Power (Page 15)".
7. Connect the device to the network.
For more information, refer to "Communication Ports (Page 29)".
8. Configure the device.
For more information, refer to "Configuring the Device (Page 26)".
2.2 Unpacking the Device
When unpacking the device, do the following:
1. Inspect the package for damage before opening it.
2. Visually inspect each item in the package for any physical damage.
3. Verify all items are included.
NOTICE
If any item is missing or damaged, contact Siemens for assistance.
2.3 Mounting the Device
The RUGGEDCOM RST2228P is designed for maximum mounting and display flexibili-
ty. It can be ordered with adapters that allow it to be installed in a 48 cm (19 in) rack
or directly on a panel.
10 RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05

Installing the Device
2.3.1Mounting the Device to a Rack
NOTICE
Heat generated by the device is channeled outwards from the enclosure. As such, it
is recommended that 2.5 cm (1 in) of space be maintained on all open sides of the
device to allow for some convectional airflow.
Forced airflow is not required. However, any increase in airflow will result in a reduc-
tion of ambient temperature and improve the long-term reliability of all equipment
mounted in the rack space.
Note
For detailed dimensions of the device with either rack or panel hardware installed,
refer to "Dimension Drawings (Page 37)".
2.3.1 Mounting the Device to a Rack
The RUGGEDCOM RST2228P can be secured to a standard 48 cm (19 in) rack using
separately purchased rack mount adapters. The adapters can be installed at the front
or rear of the chassis.
Each adapter kit includes four adapters.
To secure the device to a rack, do the following:
1. Secure the mounting adapters to both sides of the chassis.
Note
The chassis features multiple mounting holes, allowing the rack mount adapters
to be installed up to 25 mm (1 in) from the face of the device.
1
2
1 Mounting Adapter
2 Screw
Figure2.1 Installing the Mounting Adapters
RUGGEDCOM RST2228P
Installation Manual, 12/2019, C79000-G8976-1403-05 11