Siemens Gigaset A200 User manual

Gigaset A200 / BRD / A31008-A200-B101-1-19 / cover_I.fm / 16.01.2003
s
Be inspired
Gigaset
A 200
A 200 Duo

II
Brief overview
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / cover_II.fm / 16.01.2003
Brief overview
Talk key
◆Accept call
◆Start dialling
1V
22-35
ÞÜ INTMENU
key End call and
on/off key
◆End call
◆End function
◆Back one menu level
(press briefly)
◆Back to standby (press
for approx. 1 sec)
◆Handset on/off (press
for approx. 2 secs)
Select Services key
Open network access list
Caller list
Access to
◆Answering
machine/mail box
◆Caller list
Star key
◆Ringer on/off (press for
approx. 2 secs)
◆Change between
upper and lower case
Battery charging status
=flat Ufull
flashing: battery almost
empty
Internal number
of handset
keys
Activate current functions
in display
Microphone
Display
Hash key
on/off (approx. 2 secs)
key
◆Enquiry (Flash)
◆Enter dial pause
(hold down)
Time
Redial
Internal list
Menu

1
Contents
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / A_200IVZ.fm / 16.01.2003
Contents
Brief overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Making the phone ready for service . . . . . . . . . . . . 5
Positioning the base station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 1: Connecting the base station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 2: Making the handset ready for service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Step 3: Registering the handset with the base station and charging the batteries . . . 7
Switching the handset on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Activating/deactivating keypad protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operating the phone and menu management . . . . 9
Display keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Correction of wrong entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Signal tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Display in idle status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Menu management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Time functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Set date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Making calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Making external calls and ending a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Accepting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Displaying the caller's phone number (CLIP/CLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Putting on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Special services . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Withholding number display for the next call (CLIR) . . . . . . . . . . . . . . . . . . . . . . . . . 17
Callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Call waiting during an external call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Call divert (external) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Enquiry calls, toggling, conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Using an operator-provided mailbox . . . . . . . . . . 23
Setting up the mailbox for speed dialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Message waiting indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2
Contents
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / A_200IVZ.fm / 16.01.2003
Using the directory and other lists . . . . . . . . . . . . 24
Directory and network access list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Redial list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Caller list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cost-effective telephony . . . . . . . . . . . . . . . . . . . . 31
Automatic network operator prefix (preselection) . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Registering and de-regestering handsets . . . . . . . 33
Automatic registration: Gigaset A 2 handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Manual registration: Gigaset A 2 handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
De-regestering handsets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Operating more than one handset . . . . . . . . . . . . 35
Making internal calls and ending calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Internal enquiry call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Accepting/rejecting a waiting call during an internal call . . . . . . . . . . . . . . . . . . . . . . 36
Barging in on an external call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Handset settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Change display language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Activate/deactivate automatic call acceptance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Change volume and ringtone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Activate/deactivate ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Activate/deactivate battery warning tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Return handset to factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Base station settings . . . . . . . . . . . . . . . . . . . . . . . . 42
Changing the system-PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Return base station to factory (default) settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Operation with a PABX . . . . . . . . . . . . . . . . . . . . . . 43
Dialling procedure and flash time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Setting pauses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Temporary switch to tone dialling (DTMF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Questions and Answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Contact with liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Service (Customer Care) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Menu overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

3
Contents
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / A_200IVZ.fm / 16.01.2003
Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Directory key and network operator list key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Caller list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

4
Safety precautions
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / starting.fm / 16.01.2003
Safety precautions !
Use only the power unit supplied, as indicated on the underside of the base
station.
Insert only approved rechargeable batteries of the same type (page 46)!
Never use ordinary (non-rechargeable) batteries as they may pose a health
hazard or cause injury.
Make sure you insert rechargeable batteries the right way round and use the
battery type specified in this operating manual (as indicated in the handset
battery compartment)
.
The phone may affect medical equipment. Always observe the technical
restrictions in your environment (e.g. hospitals or doctors' practices).
The handset may cause an unpleasant humming noise in hearing aids. Do not
hold the handset against your ear while it is ringing (incoming call).
Do not install the phone in a bathroom or shower. The handset and base sta-
tion are not splash proof (page 46).
Do not operate the phone in places where there is a risk of explosion (such as
paint workshops).
If you give your Gigaset to someone else, make sure you also also give them
the operating manual.
Dispose of batteries and phone carefully. Do not pollute the environment.
i
◆Emergency numbers cannot be dialled if the keypad lock (page 8) is
activated!
◆Not all the functions described in this operating manual are available
in all countries.
$
‹
Œ
ƒ

5
Making the phone ready for service
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / starting.fm / 16.01.2003
Making the phone ready for service
Positioning the base station
Advice on a suitable place
The base station is designed for use in a dry, closed space with a temperature range
between +5 °C and +45 °C. Place the base station in a central position in the flat/house,
e.g. in the hallway.
Range
The range is dependent on the nature of the building and other local conditions.
Outdoors it is approx. 300 m. Indoors the range is up to 50 m.
W◆Avoid exposing your phone to sources of heat, direct sunshine, and
other electrical devices.
◆Protect your Gigaset from damp, dust, dangerous liquids and steam.

6
Making the phone ready for service
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / starting.fm / 16.01.2003
Step 1: Connecting the base station
First connect your base station to the mains supply and the telephone socket.
Underneath the base station
Power supply unit
(220/230V)
with power cable
◆Insert small power cable plug into the socket under the base station.
◆Lay the cable correctly in the cable channel.
◆Plug the power supply unit into the power socket.
Telephone jack with
telephone cable
Cable channels
◆small coloured plug on the telephone cable into the socket (clicks in).
◆Lay the cable correctly in the cable channel.
◆Plug the phone into the phone socket.
2. 1.
1.
2.
i
◆Use only the power supply unit supplied.
◆If you buy another phone cable, ensure that it has the right connector
assignment for your country.
◆To keep your phone operational, the power supply unit must always
remain plugged in.

7
Making the phone ready for service
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / starting.fm / 16.01.2003
Step 2: Making the handset ready for service
Remove protective film
Insert batteries
◆Insert the batteries the right way round – see illustration left.
◆Place the cover on the battery compartment about 3mm down from the latch and
push it up until it clicks into position.
To open the cover, press on the ridged section and push downwards.
Step 3: Registering the handset with the base station and charging
the batteries
Place your handset in the base station with the display visible at the front – the con-
firmation tone will ring (rising sequence of tones). The handset will then register itself
automatically with the base station (page 33), all symbols flashing in the display. The
process takes about a minute. Once completed, "1" will appear in the top, left-hand cor-
ner of the display. This handset has been allocated the first internal number.
Only for A200 Duo: To register a second handset, proceed as described above. After
successful registration, "2" will then appear in the top, left-hand corner of the display.
The handset display is protected by a film.
Please remove the protective film!
W
◆Insert only approved, rechargeable batteries of the same type
(page 46)! Never use normal batteries, since these could lead to a
health hazard or cause injury.
◆Do not use a non-Siemens charging unit as this could damage the
batteries.
i◆To register further handsets, see page 33 onwards.

8
Making the phone ready for service
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / starting.fm / 16.01.2003
Now leave the handset in the base station to allow the batteries to charge, since these
are not charged prior to delivery. The battery charging process is indicated on the hand-
set by a flashing battery symbol =.
Once the batteries have been charged, your phone is ready for service. You need to set
the date and time to ensure that the time of incoming calls can be noted correctly
(page 13).
Switching the handset on and off
To switch the handset on or off, press the end call key a.
Afterwards the confirmation tone rings (see page 10).
Activating/deactivating keypad protection
You can lock the handset keypad if, for example, you are carrying the handset. This pre-
vents keys beeing pressed by accident.
=Flat batteries VBatteries
2/3charged
eBatteries
1/3charged UBatteries full
i
◆For the first charging we recommend a continuous charging time as
shown in the table (page 46) – regardless of the charging status
shown in the display! Battery capacity reduces for technical reasons
after a period of time.
◆The batteries warm up during charging - this is normal and not a cause
for concern.
◆The correct charging status for the batteries will only be shown after
an unbroken charging/discharging cycle. You should therefore not
open the battery compartment unnecessarily.
◆Once the first charging cycle is completed you can put your handset
back in the base station after each call. Charging is controlled elec-
tronically. This ensures optimum battery charging without overload-
ing.
iIf you place a handset that is switched off in the base station or a charging
unit, it will automatically switch itself on.
Hold hash key down (confirmation tone). The sym-
bol Øappears in the display.
Deactivating keypad protection:
Hold hash key down (confirmation tone).
i
◆The key lock switches itself off automatically if you receive a call. At
the end of the call it switches itself on again.
◆Emergency numbers cannot be dialled if the key lock is activated!

9
Operating the phone and menu management
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / guidance.fm / 16.01.2003
Operating the phone and menu management
Display keys
Display keys are the long keys directly below the display. Your handset has two display
keys. Each of these is operated like a rocker key, i.e. it can be pushed down on the left-
hand as well as the right-hand side. Dependent on the current operating status and
which side of the key you press, you will call up a particular function. This function is
shown directly above the display key.
An example of the right-hand display key:
The word MENU is shown above the right-hand side of the display key. By pressing the
right-hand side you will open the menu. The display symbol INT is shown above the
left-hand side of the display key. By pressing the left-hand side you will open the list of
internal phones.
The various display symbols have the following meanings:
Correction of wrong entries
If you have made an input error, you can correct this.
Deleting characters ß to the left of the cursor
When entering a phone number or a text, place the cursor behind the incorrect charac-
ter with the help of the display key uor v. Then press the display key ß. The char-
acter will be deleted. Now enter the correct character.
Display keys
ÞÜINT MENU
Display symbol Meaning when pressed
ÞAutomatic redial key: Opens a list of the last 5 numbers dialled (page 28)
ÜMailbox symbol: Opens caller list and answering machine/mailbox (page 29).
[______ ]
INT Internal: Opens the list of internal phones.
[______________ ]
MENU Menu: Activates the main menu when in standby.
Activates a status-dependent menu when in talk mode.
tor sScrolls up or down.
uor vMoves cursor to the left or right.
ßDelete key: Deletes character by character, from the right to the left.
[______ ]
OK Confirm menu function or confirm and save entry.

10
Operating the phone and menu management
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / guidance.fm / 16.01.2003
Inserting a character to the left of the cursor
If you have left out a character, jump to the place where the character should be inserted
with the help of the display key u, and enter the missing character.
Overwriting a character to the right of the cursor
The number of digits you can enter for the date or time is fixed and the field contains a
default. Place the cursor in front of the wrongly entered digit with the help of the dis-
play key uor v and overwrite it.
Signal tones
Your phone will inform you acoustically about certain actions and situations.
◆Rising ringtone (confirmation tone):
The action has been carried out or the entry is correct.
◆Falling ringtone (error tone):
The function has not worked or the entry is incorrect.
Display in idle status
Return from any position in the menu to idle status
◆Hold down call end key afor approx. 1 sec. or
◆don't press a key: after 60 secs. the display will automatically return to idle status.
Changes that you have not confirmed by pressing OK will be rejected.
Menu management
Your phone has an extensive range of features. They are presented to you by a menu
that is made up of a number of levels. You will find functions such as AUDIO SET, BASE
SET etc. in the main menu, with their respective sub-menus in the next level. A menu
overview provides the necessary orientation (page 49).
Display in idle status
(date and time already
set)
1V
22-35
ÞÜINT MENU
iIf you press the call end key abriefly and just once, you will return to
the previous menu level.

11
Operating the phone and menu management
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / guidance.fm / 16.01.2003
There are two ways to access a function
◆by scrolling with the tand skeys,
◆by entering the relevant combination of digits (page 49).
Extract from the menu overview
Menu management using the example of "Set date"
Requirements: Your phone is operational (the batteries are charged), the handset is
switched on, and registered with the base station. It is currently on idle status
(page 10). Date and time have not yet been set.
The step-by-step explanation shows the handset display on the left-hand side, and an
explanation to the right with the relevant display from the instructions underneath.
3BASE SET 3-1 DATE/TIME
3-1-1 DATE SET
3-1-2 CLOCK SET
3-1-3 CLOCK
MODE
3-1-3-1 24 H
3-1-3-2 12 H
1
11
1 V
ÞÜINT MENU
AB Instruction display:
[_______________]
MENU
Open the main menu by pressing the right dis-
play key under MENU.
☛
The first function in the main menu is displayed.
1. Scroll to the BASE SET point in the menu.
Press down on the right-hand side of the left
display key until BASE SET is shown in the
display.
2. Press on the right display key under OK to
confirm your selection.
Instruction display:
[__________] [______________________________________________] [__________]
BASE SET OK
1
11
1 V
SEL SERVICES
ts OK
AB
☛
1.
☛
2.

12
Operating the phone and menu management
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / guidance.fm / 16.01.2003
The date is set. Now press the call end key ato leave the menu point. Next set the time
(page 13) and if necessary the display mode (page 14).
The sub-menu DATE/TIME is shown in the dis-
play.
Press on the right display key under OK, to con-
firm DATE/TIME the selection.
Instruction display:
[______________________________________________] [__________]
DATE/TIME OK
1
11
1 V
DATE/TIME
ts OK
AB
☛
The sub-menu DATE SET is shown in the dis-
play.
Press on the right display key under OK, to con-
firm DATE SET.
Instruction display:
[______________________________________________] [__________]
DATE SET OK
1
11
1 V
DATE SET
ts OK
AB
☛
V
20-05-03
uv OK
AB
ABAB
AB
☛
An entry field opens.
1. Enter the current date with the number keys,
e.g. 2QQ5QI for 20.05.2003.
2. Press the right display key under OK, to con-
firm the date you have entered.
A confirmation tone sounds (rising ringtone).
Instruction display:
[______]
OK

13
Time functions
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / TimeCalendar.fm / 16.01.2003
Time functions
Set date and time
Settings for date and time are needed to ensure that these are shown correctly for
incoming calls. For the time you can choose between a 12-hour and 24-hour display
(default setting).
Date
Time
[_______________]
MENU Press display key to open menu.
[__________] [______________________________________________] [__________]BASE SET OK Select and confirm.
[______________________________________________] [__________]
DATE/TIME OK Confirm.
[______________________________________________] [__________]
DATE SET OK Confirm. The current setting is displayed in the for-
mat DD-MM-YY.
[______]
OK Enter day/month/year and confirm.
Example: Press the keys 2QQ5QI
for "20.05.2003".
Long press (return to idle status).
[_______________]
MENU Press display key to open menu.
[__________] [______________________________________________] [__________]
BASE SET OK Select and confirm.
[______________________________________________] [__________]
DATE/TIME OK Confirm.
[__________] [______________________________________________] [__________]
CLOCK SET OK Select and confirm. The current setting is displayed
in the format HH-MM.
[______]
OK Enter hours/minutes. Example: Press the keys
1OQ5for "19.05".
Long press (return to idle status).
iIf you want a 12-hour display you must enter QMQ5for "19:05",
confirm with OK and then confirm PM OK for the 2nd half of the day
(AM = 1st half; PM = 2nd half).

14
Time functions
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / TimeCalendar.fm / 16.01.2003
Display mode (24-hour or 12-hour display)
[_______________]
MENU Press display key to open menu.
[__________] [______________________________________________] [__________]
BASE SET OK Select and confirm.
[______________________________________________] [__________]
DATE/TIME OK Confirm.
[__________] [______________________________________________] [__________]
CLOCK MODE OK Select and confirm.
either ... Select 12-hour display:
[__________] [______________________________________________] [__________]
12 H OK Select and confirm.
or ... Select 24-hour display:
[______________________________________________] [__________]24 H OK Confirm.
Long press (return to idle status).

15
Making calls
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / telephony.fm / 16.01.2003
Making calls
Making external calls and ending a call
External calls are calls using the public telephone network.
Accepting a call
Your handset rings, the call is shown in the display.
Press the call key cto accept the call. If the handset is in the base station/charge sta-
tion and automatic call acceptance is activated (page 38), you only have to pick up the
phone from the station to accept the call.
Enter the phone number and press the talk key.
The phone number is dialled.
Finish call:
Press end call key.
i
◆You can also first press the talk key c(you will hear the dial tone)
and then enter the phone number.
◆You end the call by pressing the end call key a.
◆To find out how to make internal calls read page 35.
i◆If the ringer is disturbing you, press the MENU display key and
confirm SILENT with OK. As long as the call is shown in the display,
you can accept it.

16
Making calls
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / telephony.fm / 16.01.2003
Displaying the caller's phone number (CLIP/CLI)
The phone number of the caller is shown in the display during a call.
Requirements:
1. You have asked your network operator to enable the caller's phone number to be
shown in your display (CLIP).
2. The caller has asked the network operator to pass on his/her phone number (CLI).
If you have stored an entry for a phone number in your handset directory (see page 24),
the name in the directory will appear instead of the phone number, e.g. "Tom".
If you do not have CLIP, "<< >>" will appear instead of the phone number.
If the caller does not have CLI or has withheld his/her phone number, "WITHHELD" will
appear in the display.
Putting on hold
During external calls you can put the incoming call on hold, so that, you can talk dis-
crectly to another person in the room for example. During this time the caller on the
phone cannot hear you (music on hold). Nor can you hear the caller.
iPassing on a phone number may incur costs. For more information please
contact your network operator.
Phone number
or name
V
023031230
MENU
CLIP Calling Line Identification Presentation = the caller's phone number is
displayed
CLI Calling Line Identification = your own phone number is passed on during
external calls.
[_______]INT Press (INT ). The conversation takes place (music on
hold).
Ending call hold:
[_______________]
MENU Press display key to open menu.
[______________________________________________] [__________]
GO BACK OK Confirm.

17
Special services
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / telephony.fm / 16.01.2003
Special services
Special services are functions offered by your network operator. You can only use these
services if you have requested them from your network operator.
The following selected services are those offered by your network provider. Contact
your network operator to see which special and standard services are available to you.
The menu offers you the following services:
◆Withhold number display
◆Activate callback/end early
◆Activate/deactivate call waiting and accept/refuse waiting calls
◆Call diversion
◆Initiate/end enquiry, swap, conference call
Withholding number display for the next call (CLIR)
If enabled by your network operator, your phone number appears in the display of the
external party you are talking to. If you want to withhold your phone number, you can
do so for the next call.
iYou can find out more about these functions from your operator, e.g.
from British Telecom (www.bt.co.uk). Your network operator will also
help you with questions about costs for these services or any problems.
[_______________]
MENU Press display key to open menu.
[______________________________________________] [__________]
SEL SERVICES OK Confirm.
[__________] [______________________________________________] [__________]
WITHHOLD NO OK Select and confirm.
[______]
OK Enter phone number and confirm.
Your phone number is withheld for this call.
CLIR Calling Line Identification Restriction = passing on your own phone number is
temporarily suppressed.

18
Special services
Gigaset A200 / englisch / A31008-A200-B101-1-7619 / telephony.fm / 16.01.2003
Callback
If the number you are calling is engaged (busy tone), you can set up a callback. As soon
as the line is free again, you will receive an automatic callback.
Setting up callback
You hear the busy tone. After approx. 8 secs. the display changes. Then:
Deactivating a callback
You can deactivate a callback that you have set up.
[_______________]
MENU Press display key to open menu.
[__________] [______________________________________________] [__________]
RINGBACK OK Select and confirm.
After the confirmation tone from the phone
network:
Long press (return to idle status).
i◆Only one callback is possible at a time.
◆The callback remains active for a maximum 45 mins.
[_______________]
MENU Press display key to open menu.
[______________________________________________] [__________]
SEL SERVICES OK Confirm.
[__________] [______________________________________________] [__________]
RINGBACK OFF OK Select and confirm.
After the confirmation tone from the phone
network:
Long press (return to idle status).