Sierra Flame FS-26-922 Installation instructions

FS-26-922
INSTALLER: LEAVE OWNER’S MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN OWNER’S MANUAL FOR FUTURE REFERENCE.
SAFETY INFORMATION
WARNING
For yo r safety, always comply with all
warnings and safety instr ctions
contained in this man al to prevent
personal inj ry or property damage.
Do not store or use gasoline or other flammable vapors
and li uids in the vicinity of this appliance.
Version:202310
INSTALLATION /OWNER’S MANUAL
FREE STANDIN
( FS26922-1 )

2
TABLE OF CONTENTS
IMPORTANT INSTRUCTIONS ......................................................................................................................................... 3
FCC CAUTIONS .................................................................................................................................................................. 4
UNPACKING AND TESTING THE APPLIANCE .......................................................................................................... 5
GROUNDING APPLIANCE ............................................................................................................................................... 5
LOCATING THE FIREPLACE ........................................................................................................................................... 5
FS-26-922 (FS26922-1) ........................................................................................................................................................ 6
HARD IRE INSTALLATION .......................................................................................................................................... 7
MEDIA OPTIONS ................................................................................................................................................................ 8
DECORATIVE MEDIA INSTALLATION ........................................................................................................................8
OPERATION .........................................................................................................................................................................9
MANUAL OPERATION .....................................................................................................................................................9
REMOTE CONTROL OPERATION ................................................................................................................................10
IFI OPERATION .............................................................................................................................................................13
REPLACEMENT PARTS .................................................................................................................................................. 16
EXPLODED VIE ............................................................................................................................................................ 17
TROUBLE SHOOTING ..................................................................................................................................................... 19
SERVICE HISTORY .......................................................................................................................................................... 20
ARRANTY ...................................................................................................................................................................... 21
IRING DIAGRAM .......................................................................................................................................................... 18
Please read and carefully follow all of the instruction found in this manual. The instructions
included here will assure that you have many years of dependable and enjoyable service
from your Sierra flame Electric Fireplace.
QR Code

IMPORTANT INSTRUCTIONS
PLEASE RETA N TH S USER GU DE FOR FUTURE REFERENCE
When using electrical appliances, basic precautions should always be followed to reduce the
risk of fire, electric shock, and injury to persons, including the following:
1) Read all instructions before using this fireplace
2) The fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.
Keep combustible material such as furniture, cushions, bedding, paper, clothes, curtains
at least 3 feet from the front of the unit
3) Extreme caution is necessary when any heater is used near children and whenever the
unit is left operating and unattended.
4) Do not operate a fireplace with a damaged cord or plug, or if the heater has
malfunctioned, the fireplace has drooped or damaged in any manner
5) Not all fireplaces are suitable for use in bathrooms or laundry facilities. Please consult
with individual product literature to confirm suitability
6) Do not run the cord under carpeting. Do not cover cord with throw rugs, runners or the
like. Arrange the cord away from traffic area and where it will not be tripped over
7) Do not modify this fireplace. Use it as described in the manual. Any other use not
recommended by the manufacture may cause fire, shock or injury to persons
8) Do not use this heater with programmer, timer, separate remote-control system or any
other device that switches the heater on automatically, since a fire risk exists if the heater
is covered or positioned incorrectly
9) Disconnect all power supply before cleaning, maintenance or relocation of the fireplace
10) Keep the heater clean. Do not allow any objects to enter any ventilation or exhaust
opening as this may cause electric shock, fire or damage to the heater
11) Do not immerse the cord, plug or any part of the appliance in water or any other liquid
12) n order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this
appliance must not be supplied through an external switching device
3
CAUTION: Procedures and techniques, which, if not carefully followed, will result in damage to
the equipment.
WARNIN : Procedures and techniques, which, if not carefully followed, will expose the user to
the risk of fire, serious injury, illness or death.
Consult with professional electrician and adhere to all code requirements for
installations in bathrooms
SAVE THESE INSTRUCTIONS

FCC CAUTIONS
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) this device must
accept any interference received, including interference that may cause undesired
operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
4

UNPACKING A
ND TESTING APPLIANCE
Carefully remove the appliance from the box.
Prior to installing the appliance test to make sure the appliance operates properly by plugging
the power supply cord into a 120 Volt grounded outlet.
Test all aspects of its operation (
components are operating correctly.
As with most electronic devices your new electric fireplace has been designed to operate at
temperatures between 5 ℃ (41
℉
fireplace to reach room temperature before turning it on.
NOTE: There may be trace of odor during the first few minutes of initial use This is
harmless, normal and will never occur again
GROUNDING APPLIANCE
This appliance is for use on
120 Volts. The cord has a plug as shown in (A). An adapter as
shown in (C) is available for connecting three
receptacles. The green grounding lug extending from the adapter must be connected to a
permanent ground suc
h as a properly grounded outlet box. The adapter should not be used if a
three-
slot grounded receptacle is available.
To disconnect appliance turn controls to off then remove plug from outlet.
LOCATING THE FIREPLACE
Plan where to l
ocate and frame the fireplace. This will save time and money later when you
the following:
1.
and ceiling clearances
2.
Consider a location where the fireplac
windows or doors.
A 15 ampere 120 Volt 60 Hz branch circuit with proper ground must be available at the
location. Preferably a dedicated branch circuit should be provided to avoid circuit breakers
to trip of fuses to blow.
ND TESTING APPLIANCE
Carefully remove the appliance from the box.
Prior to installing the appliance test to make sure the appliance operates properly by plugging
the power supply cord into a 120 Volt grounded outl
et.
Test all aspects of its operation (
manual switches remote and heater) to make sure all
components are operating correctly.
As with most electronic devices your new electric fireplace has been designed to operate at
℉
) and 35 ℃ (95℉
). During the cold winter mon
fireplace to reach room temperature before turning
it on.
NOTE: There may be trace of odor during the first few minutes of initial use This is
harmless, normal and will never occur again
120 Volts. The cord has a plug as shown in (A). An adapter as
shown in (C) is available for connecting three
-
blade grounding type plugs to two
receptacles. The green grounding lug extending from the adapter must be connected to a
h as a properly grounded outlet box. The adapter should not be used if a
slot grounded receptacle is available.
To disconnect appliance turn controls to off then remove plug from outlet.
LOCATING THE FIREPLACE
ocate and frame the fireplace. Consider the following:
Consider a location where the fireplac
e screen will not be exposed to direct sunlight from
A 15 ampere 120 Volt 60 Hz branch circuit with proper ground must be available at the
location. Preferably a dedicated branch circuit should be provided to avoid circuit breakers
Prior to installing the appliance test to make sure the appliance operates properly by plugging
manual switches remote and heater) to make sure al
l
As with most electronic devices your new electric fireplace has been designed to operate at
). During the cold winter mon
ths allow the
NOTE: There may be trace of odor during the first few minutes of initial use This is
120 Volts. The cord has a plug as shown in (A). An
adapter as
blade grounding type plugs to two
-slot
receptacles. The green grounding lug extending from the adapter must be connected to a
h as a properly grounded outlet box. The adapter sh
ould not be used if a
To disconnect appliance turn controls to off then remove plug from outlet.
e screen will not be exposed to direct sunlight fro
m
A 15 ampere 120 Volt 60 Hz branch circuit with proper ground must be available at the
location. Preferably a dedicated branch circuit should be provided to avoid circuit breakers
Note : Adaptor are NOT for use in Canada
5

Description Free StandingAppliance
Voltage 120V AC60Hz
Watts 1500WMax
NOHEATER 25W
MOTOR HEATER 19W
ApplianceWidth 25 5/8" or 65.2 cm
ApplianceHeight 28" or 71.2 cm
ApplianceDepth 17 1/2" or 44.5 cm
Gross Weight 71.6 lbs or 32.5 kgs
PlugLocation Left side
Cord Length 707/8”or180 cm
This appliancehasbeentestedin
accordancewiththeULStandard2021
forfixedandlocationdedicated
electricroomappliancesintheUnited
Statesand Canada.Ifyouneed
assistanceduringinstallation,please
contactyourlocal dealer.
BTU 5118
NOTE:Thisappliancemustbe
electricallywiredandgroundedin
accordancewithlocalcodes.Inthe
absenceoflocalcodes,usethe
currentCSAC22.1CanadianElectrical
Codein CanadaortheANSI/NFPA70
NationalElectricalCodein theUnited
States.
FS-26-922 (FS26922-01)
6

Turnofftheappliancecompletelyand let coolbeforeservicing.Onlyaqualifiedserviceperson
should serviceandrepairthiselectricappliance.
If itis necessarytohardwirethisappliance,aqualifiedelectricianmustremovethecordconnection,
and wiretheappliancedirectlyto thehousehold wiring.
This appliancemustbeelectricallyconnectedandgroundedinaccordancewith localcodes,ifhard
wired.Intheabsenceoflocal codes, usethecurrentCSA C22.1CANADIANELECTRICAL CODEin
CanadaorthecurrentANSI/NFPA70 NATIONAL ELECTRICAL CODEintheUnited States.
1. Removethecoverplatefromtheleftsideoftheappliancebyremovingthetwoscrews, as
shownbelow.Unscrewand removepowercord.
2. Attachthewiringtothejunctionblock.Pleasemakesurethelivewiregoes into the "L", the
neutral wire into "N" and the ground wire into "G".
3. Puttheplatebackandscrew back.
HARD IRE INSTALLATION
7

STEP1: Unplugtheunitfromwall and make
surecontrols are switched off.
STEP2: Pushupwards(asshowsinbellow
picture)andremovethefront paneltodecorate
yourfireplace.Pourthedecorativemediainto
thetray.Feelfree touseanycombinationoffire
glass mediathatyoufindmostappealing.
STEP3: Afterfinishingdecoration,putbackthe
Hold here firmly, then push upwards to take off
the front glass panel.
The glass panel is hooked by 2 hooks on each
side.
Then you can take off
the glass panel.
frontglasspanel.
Now you can start to decorate your fireplace
This fireplaceincludesthefollowingdecorative
media:
MEDIA OPTIONS
DECORATIVE MEDIA INSTALLATION
DECORATIVE MEDIA INSTALLATION
Your fireplace shipped with the following media:
3 bags of sable glass and an 8 piece log set.
Customers can decorate their fireplace
according to their wishes with shipped media.
Sable
Log Set 8 pieces

Thefireplacecanbeoperatedeitherbytheswitcheslocatedontheleftfront ofthefireplaceunitor
bysupplied remotecontrol.
Pushtoreveal themanual controlpanel.(As showsin bellowpicture)
Push here to open the touch control panel
MANUAL OPERATION
1.
2.
Press to turn on and off the fireplace.
Press to adjust the flame brightness. There are 6 brightness levels（L6-L1） and
an off(OF) position. Each time the flame button is pressed, the brightness of the flame
decrease.
press the flame button for 10 seconds, the timing indicator light on and will rapidly
blinks, at this time, You can use the TuyaSmart APP to connect to the fireplace.
3. Press to adjust the ember Bed /Moodlight brightness. There are 11 brightness.
levels (d11-d2), dynamic condition(d1) ,and the OFF(OF) setting you can cycle through.
4. Press to set the turn-off time, 30min-1h-2h-3h-4h-5h-6h-7h-8h-t0. The indicator light
the current timing. If the timing in off position, the second press will show 30. Multiple times
to set operating duration to OF, 30 min, 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h.
5. Press or the first time to display the current setting temperature，press the button
again to clear the current temperature. If the heater in off position, the second press will
show 22℃(72℉).Multiple times to set ambient temperatures at 22℃( 72℉) , 23℃
(74℉) ,24℃( 76℉) , 25℃( 78℉) , 26℃( 80℉) , 27℃( 82℉) , 28℃( 84℉) ,15℃( 52℉) ,
16℃( 54℉) , 17℃( 56℉) ,18℃( 58℉) , 19℃( 60℉) , 20℃( 62℉) , 21℃( 64℉) .
Temperature unit convert functionZ When the heater is on, press and hold the“ ”
Button for 5 seconds, current temperature unit display will convert to another temperature
unit.
OPERATION
9

10
For remote to function make sure the fireplace is plugged in and the remote has batteries.
Important: When operating the remote make sure you point the remote to the center of the
fireplace. Each time you press the button, the buzzer inside the unit will beep once. It takes
some time for the receiver to respond to the transmitter. Do not PRESS the buttons more
than once within two seconds for correct operation.
REMOTE CONTROL OPERATION
REMOTE LEGEND
POWER ON/OFF BUTTON
TIMER BUTTON
SET TIME AND DATE BUTTON
DIRECTIONAL KEY BUTTONS
HEAT SETTING BUTTON
FLAME SPEED SETTING
MOODLIGHT/EMBER LIGHT SETTING
FLAME ON/OFF SETTING
RED FLAME BUTTON
ORANGE FLAME BUTTON
YELLOW FLAME BUTTON
TIMER FUNCTION BUTTON
PRESS REFER BUTTON
HOW TO SET-UP YOUR FIREPLACE WITH YOUR REMOTE
Press the to activate the remote control and press to set the time and date.
When one of the “Sun” “Mon” “ Tue” “Wed” “Thu” “Fri” “Sat” is flashing, press or to
set the day of the week, press to confirm day of the week and then enter hour setting.
Press or
setting. Press
to set the hour, press to confirm the hour and then enter minute
or to set the minute and press to confirm the minute and
finish time setting.
Press this Power button to turn on and off the fireplace.

10
Press this Timer button to set the time to turn off the fireplace. The available settings
range from 30 minutes to 8 hours. As shown in the following: 0:30 - 1:00 - 1:30 - 2:00 -
2:30 - 3:00 - 3:30 - 4:00 - 4:30 - 5:00 - 5:30 - 6:00 - 6:30 - 7:00 - 7:30 - 8:00. Once you
have set the timer, the icon will be displayed on the LCD screen of the remote
control. Press this button again to cancel the timer setting and the icon disappears.
Each time the Heater Button is pressed, the power of the heater will change. As shown
the following: H1- H2- AUTO （2 2℃）- OFF（No display）
H1 means the firepalce on Low Heat/750W.
H2 means the fireplace on High Heat/1500W.
HOW SET THE HEAT
HOW TO SET-UP TIMER
AUTO means fireplace can automatically adjust to the temperature you set. When in
AUTO, you can set the desired temperature with or keys. You can switch
temperature between Celsius and Fahrenheit with or keys.When it is on Auto
mode,fireplace operate at 1500W.
HOW TO SET THE HEAT MANUALLY
HOW TO SET THE FLAME SPEED
Press this button to adjust the speed of the flame. There are 3 options: High- Medium-
Low.
HOW TO SET THE EMBER TRAY LIGHTING
The Ember bed /moodlight Button turn the ember bed or moodlight on and off.When in
on position,the display screen of the remote control shows AD1.,when the
number“1”flash,you can set the color with or keys. There are 10 different colors
(AD1-10) and dynamic condition(AD11) to choose from.

11
Press once, 7 days from Monday to Sunday will display on the LCD screen of
the remote control, press within 5 seconds to enter 7 day timer function. When
“Sun” flashes, press or to select the day that you want to set, press to
confirm your setting. Then “ON” will be display on the LCD screen of the remote
control, at the same time, digital of time hour flashes, press or to set the
time to turn the fireplace on. After setting the startup time, “OFF” will be displayed on
the LCD screen and press or to set the shutdown time. When the
shutdown time’s set, “AUTO” will be displayed on the LCD screen of the remote
control and the digital of temperature flashes. At this time, you can set the
temperature by or . Now, you have finished setting of this function.
HOW TO SET THE 7 DAY TIMER
When the 7 day timer’s set, the icon will be displayed on the LCD screen of the
remote control. Press again to cancel the 7 da
will disappears.
NOTE: If the 7 day timing and the general timing are set at the same time, the
system will respond to an earlier shutdown time.
y timer and the icon
Press Refer button to check the settings of 7 day timer. Press or to see the
settings of the day of the week and or the settings of the startup and
shutdown time.
HOW TO REFER BACK TO THE TIMER YOU HAVE SET

13
WIFI OPERATION
IN TALL Tuya mart life
There are 2 ways to install TuyaSmart;
1. Search for “TuyaSmart life” in the APP store on your phone, download and install.
2. Scan the QR code below with your mobile phone.
WIFI ETTING AND FIREPLACE OPERATION
1. Create an account and log in.
2. When you log in, touch “+” (FIG.1) to enter in FIG.2. Touch “others” on the left corner first
and then choose “Connector (Wi-fi)” to enter in FIG.3 to set your Wi-fi account and
password.
FIG.1 FIG. 2 FIG.3

14
FIG.4
3. Press (flame button) on the touch panel of the fireplace for more than 5 seconds
when the fireplace in standby mode. There will be 2 beeps come out from the fireplace
and the (flame button) will flash as well indicating that Wi-fi is in EZ mode. Then
please confirm to go next. (FIG.5)
4. The APP will scan (FIG.6) and add the fireplace to APP (FIG.7) automatically. Please
make sure the Wi-fi account and password you set are correct and Wi-fi signal is good.
5. Touch “Done” to finish Wi-fi setting.(FIG.7)
FIG.5 FIG.6 FIG.7

15
6. Now you are in the interface like FIG.7. You can operate the fireplace via Wi-fi.
FIG.7
NOTE: Turn off the flashing blue Wifi indicator light
Touch the (power button) once, the blue light will stop flashing.

16
*There is a QR code in page 2 of the manual, at the bottom of the table of contents.
Push here and you will
find the QR code
REPLACEMENT PART
There is a QR code where the arrow is marked in F G 2. Push the panel to reveal the QR code. Scan
the code to get the replacement parts list for your reference. You will get a detailed parts list with
images.
FIG 2
FIG 1

EXPLODEDVIEW
17

POWER
ADAPTER
FLAME MOTOR
RECEIVER
TEMP SENSOR
HEATER
NL
12V 100-240V
TOP LIGHT
H2 H1
F-N1 M-N1 P-N1 R-N1
TEMP +-
RF
FLAME EMBER
WIFI
T-IN
F-N2
TRAN.-I
P-L
DH-SJ-CM2-V1.2
TEMPTIME HEATFLAMEON/OFF C11
HW
STB
CLK
SD
CL
+
-
+12V
A+ A- B+ B-
Stepper Motor
LED4-M23
2018/07/21
FR-4
SHENGYI
+
E
Y
B
B
Y
E
+
J2
YR1 27
ER1 27
+
B3
+
E2
+
Y2
+
B2
+
E3
+
Y3
+
B4
+
B1
+
Y1
+
E1
+
Y4
+
E4 J1 SO
SI
WIFI
+ E Y B BYE+
SHENGYI FR-4 2017/04/22
LED3-M33
Y12E12 B12
B11E11 Y11
B10
E10 Y10
B9E9 Y9
B8
E8 Y8B7E7 Y7B6E6 Y6B5E5 Y5B4E4 Y4B3E3 Y3
B2
E2 Y2
Y1E1
SO
SI
B1
上部丝印层
+ E Y B BYE+
SHENGYI FR-4 2017/04/22
LED3-M33
Y12E12 B12B11E11 Y11
B10
E10 Y10B9E9 Y9
B8
E8 Y8B7E7 Y7
B6E6 Y6
B5
E5 Y5B4
E4 Y4
B3E3 Y3
B2
E2 Y2
Y1E1
SO
SI
B1
LED4-M23
2018/07/21
FR-4
SHENGYI
+
E
Y
B
B
Y
E
+
J2
YR1 27
ER1 27
+
B3
+
E2
+
Y2
+
B2
+
E3
+
Y3
+
B4
+
B1
+
Y1
+
E1
+
Y4
+
E4 J1 SO
SI
FLAME AND
TRAY LIGHT
GND
WIRING DIAGRAM
1

TROUBLESHOOTING
PROBLEMPOSSIBLECAUSE SOLUTION
FlameLEDsareburntout InspecttheLEDsand replacethemif
necessary.
Dim orno flame
Backblackcloth is fallingoff
and rolled up in the flicker Changea flicker and back black cloth.
Emberbedis not
glowingordimming EmberLEDsare burnt out InspecttheemberbedLEDsand replacethemifnecessary.
Appliancehasoverheatedand
safetydevicehascausedthe
thermal switchtodisconnect
Turnoffthemainswitch,allow
appliancetocoolfor10minutes, then
turn iton.
Housecircuitbreakerhas
tripped Reset housecircuitbreaker.
Applianceturnsoffand
will not turnon
Appliancesfusehasblown Replacethefuse.
Applianceis notpluggedintoan
electrical outlet Checkplugandplugin.
Appliancehasoverheatedand
safetydevicehascausedthe
thermal switchtodisconnect
Turnoffthemainswitch,allow
appliancetocoolfor10minutes, then
turn iton.
Appliancewill notcome
onwhenswitchis
flipped to ON
Circuitboardis burntout Inspectthecircuitboardandreplace
it ifnecessary.
No warmaircomingout
of appliance Heateris burnt out Inspecttheburnerand heater assemblyandreplaceitif necessary.
Flamesputters Flamemotoris defective. Call aqualifiedservicetechnicianand
replaceflamemotor.
RemoteControldoes
not work. Lowbatteries. Unitswitch in “O”position. ReplaceAAA batteriesinremote control.
Turn theswitchin “I”position.
Flameis fixed. Wiringmaybelooseorthe
flamemotormaybedefective.
19

SERVICE HISTORY
This heatermustbeserviced annuallydependingonusage.
DateDealer
Name Servicetechnician Name ServicePerformed Special Concerns
NOTES:
20