Sierra InnovaMass 240-V User manual

Series 240/241 Instruction Manual Table of Contents
IM-24 0-1
Sierra Series 240 and 241
Innova-Mass™ Multi-Parameter
Vortex Mass Flow Meters
Models 240- V and 241-V
Instruction Manual
Part Number: IM-24, Rev. E 11/10
IMPORTANT: This manual is for use with 240/241 Vortex Products
purchased February 2008 or later

Table of Contents Series 240/241 Instruction Manual
0-2 IM-24
GLOBAL SUPPORT LOCATIONS: WE ARE HERE TO HELP!
CORPORATE HEADQUARTERS
5 Harris Court, Building L Monterey, CA 93940
Phone [phone] [phone] Fax [phone]
www.sierrainstruments.com
EUROPE HEADQUARTERS
Bijlmansweid 2 1934RE Egmond aan den Hoef
The Netherlands
Phone [phone] Fax [phone]
ASIA HEADQUARTERS
Rm. 618, Tomson Centre, Bldg A, 188 Zhang Yang Road
Pu Dong New District, Shanghai, P.R. China
Phone: + 8621 5879 8521 Fax: [phone]
IMPORTANT CUSTOMER NOTICE: OXYGEN SERVICE
Unless you have specifically ordered Sierra’s optional O2cleaning, this flow meter may not
be fit for oxygen service. Sierra Instruments, Inc., is not liable for any damage or personal in-
jury, whatsoever, resulting from the use of Sierra Instruments standard mass flow meters for
oxygen gas. You are responsible for cleaning the mass flow meter to the degree required for
your oxygen flow application.
© COPYRIGHT SIERRA INSTRUMENTS 2010
No part of this publication may be copied or distributed, transmitted, transcribed, stored in
a retrieval system, or translated into any human or computer language, in any form or by
any means, electronic, mechanical, manual, or otherwise, or disclosed to third parties
without the express written permission of Sierra Instruments. The information contained in
this manual is subject to change without notice.
TRADEMARKS
Innova-Flo™ and Innova-Mass™ are trademarks of Sierra Instruments, Inc. Other product
and company names listed in this manual are trademarks or trade names of their respec-
tive manufacturers.

Series 240/241 Instruction Manual Table of Contents
IM-24 0-3
Table of Contents
Chapter 1 Introduction
Innova-Flo™Vortex Flow Meters........................................................1-1
Using this Manual ......................................................................... 1-1
Note and Safety Information.........................................................1-2
Receipt of System Components ....................................................1-2
Technical Assistance.....................................................................1-2
How the Innova-Flo Vortex Flow Meter Operates..............................1-3
Velocity Measurement/Pressure Drop........................................... 1-3
Flow Meter Configurations..................................................................1-7
Chapter 2 Installation
Installation Overview...........................................................................2-1
Flow Meter Installation Requirements..........................................2-1
Unobstructed Flow Requirements.................................................2-2
Series 240 In-Line Flow Meter Installation.........................................2-3
Wafer-Style Flow Meter Installation............................................. 2-4
Flange-Style Flow Meter Installation............................................2-5
Series 241 Insertion Flow Meter Installation.......................................2-6
Cold Tap Guidelines......................................................................2-7
Hot Tap Guidelines ....................................................................... 2-8
Flow Meter Insertion ...........................................................................2-9
Installing Meters with a Compression Connection .....................2-10
Installing Meters with a Packing Gland Connection................... 2-12
Installing Meters (Packing Gland), No Insertion Tool................ 2-15
Adjusting Meter Orientation..............................................................2-17
Display/Keypad Adjustment ....................................................... 2-17
Enclosure Adjustment.................................................................2-18
Wiring Connections...........................................................................2-19
Input Power Connections............................................................2-19
Pulse Output Connections........................................................... 2-21
Remote Electronics Wiring.........................................................2-22
Chapter 3 Operating Instructions
Flow Meter Display/Keypad................................................................ 3-1
Start Up................................................................................................3-2
Using the Setup Menus........................................................................ 3-3
Programming the Flow Meter.......................................................3-3
Output Menu .................................................................................3-4
Display Menu................................................................................3-5
Totalizer Menu.............................................................................. 3-6
Units Menu.................................................................................... 3-7
Diagnostics Menu..........................................................................3-8

Table of Contents Series 240/241 Instruction Manual
0-4 IM-24
Calibration Menu...........................................................................3-9
Password Menu...........................................................................3-10
Chapter 4 HART Communications
Wiring .................................................................................................4-1
HART Menus ......................................................................................4-2
Fast Key Sequence ..............................................................................4-3
Fast Key Sequence (continued) ..........................................................4-4
Chapter 5 Troubleshooting and Repair
Hidden Diagnostics Menus..................................................................5-1
Column One Hidden Diagnostics Values......................................5-2
Column Two Hidden Diagnostics Values.....................................5-3
Analog Output Calibration ..................................................................5-4
Troubleshooting the Flow Meter .........................................................5-4
Symptom: Output at no Flow........................................................5-4
Symptom: Erratic Output ..............................................................5-4
Symptom: No Output....................................................................5-5
Electronics Assembly Replacement.....................................................5-6
Returning Equipment to the Factory....................................................5-7
Appendix A Product Specifications
Appendix B Glossary
Appendix C ATEX-IECEx

Series 240/241 Instruction Manual Table of Contents
IM-24 0-5
Warnings and Cautions
Warning!
Agency approval for hazardous location installations varies between flow meter models.
Consult the factory for specific flow meter approvals before any hazardous location instal-
lation. For explosion proof installations, you must use solid metal conduit and follow
NFPA (or your local code) approved wiring methods.
Hot tapping must be performed by a trained professional. U.S. regulations often require a
hot tap permit. The manufacturer of the hot tap equipment and/or the contractor perform-
ing the hot tap is responsible for providing proof of such a permit.
All flow meter connections, isolation valves and fittings for cold/hot tapping must have the
same or higher pressure rating as the main pipeline.
For Series 241 insertion flow meter installations, an insertion tool must be used for any
installation where a flow meter is inserted under pressure greater than 50 psig.
To avoid serious injury, DO NOT loosen a compression fitting under pressure.
All wiring procedures must be performed with the power Off.
Before attempting any flow meter repair, verify that the line is de-pressurized.
Always remove main power before disassembling any part of the mass flow meter.
Caution!
Calibration must be performed by qualified personnel. Sierra Instruments, Inc., strongly re-
commends that you return your flow meter to the factory for calibration.
In order to achieve accurate and repeatable performance, the flow meter must be in-
stalled with the specified minimum length of straight pipe upstream and downstream of
the flow meter’s sensor head.
When using toxic or corrosive gases, purge the line with inert gas for a minimum of four
hours at full gas flow before installing the flow meter.
Wafer-style flow meter gaskets must be carefully aligned to ensure accurate flow mea-
surement.
For Series 241 insertion flow meter installations, the sensor alignment pointer must point
downstream in the direction of flow.

Series 240/241 Instruction Manual Chapter 1 Introduction
IM-24 1-1
Chapter 1 Introduction
Innova-Flo™ Vortex Flow Meters
The Sierra Instruments’ Series 240 In-Line and the Series 241 Insertion
Innova-Flo™ Vortex Flow Meters provide a reliable solution for process
flow measurement. From a single entry point in the pipeline, Innova-Flo
meters offer precise measurements of mass or volumetric flow. The ve-
locity sensor reduces the effects of pipeline vibration by incorporating a
unique piezoelectric element that senses the vortex frequency. To extend
rangeability at the low end of flow, the meter’s smart electronics calcu-
lates the Reynolds number (Re) based on constant values of fluid density
and viscosity stored in memory and automatically corrects for any non-
linearity down to Re = 5,000.
Innova-Flo digital electronics allows reconfiguration for most gases, liq-
uids and steam. The instrument is loop powered (12 to 36 VDC) with
two output signals. The pulse output signal is proportional to volumetric
flow rate; the analog linear 4-20 mA signal offers your choice of volume-
tric flow rate or mass flow rate. The mass flow rate is based on a constant
value for fluid density stored in the instrument’s memory. The local key-
pad/display provides instantaneous flow rate in engineering units or tota-
lized flow.
The Sierra Series 240 and 241 Innova-Flo Meters simple installation
combines with an easy-to-use interface that provides quick set up, long
term reliability and accurate flow measurement over a wide range of
flows and conditions.
Using This Manual
This manual provides the information needed to install and operate the
Series 240 In-Line and Series 241 Insertion Innova-Flo Vortex Flow Me-
ters. The four chapters of this manual cover these areas:
•Chapter 1 includes the introduction and product description
•Chapter 2 provides information needed for installation
•Chapter 3 describes system operation and programming
•Chapter 4 covers troubleshooting and repair
The product specifications are found in Appendix A. Appendix B con-
tains a glossary of terms.

Chapter 1 Introduction Series 240/241 Instruction Manual
1-2 IM-24
Note and Safety Information
We use note, caution and warning statements throughout this book to
draw your attention to important information.
Warning!
Caution! Note
This statement appears with
information that is important to
protect people and equipment
from damage. Pay very close
attention to all warnings that
apply to your application.
This statement appears with
information that is important
for protecting your equipment
and performance. Read and
follow all cautions that apply
to your application.
This statement appears with a
short message to alert you to
an important detail.
Receipt of System Components
When receiving a Sierra flow meter, carefully check the outside packing
carton for damage incurred in shipment. If the carton is damaged, notify
the local carrier and submit a report to the factory or distributor. Remove
the packing slip and check that all ordered components are present. Make
sure any spare parts or accessories are not discarded with the packing
material. Do not return any equipment to the factory without first con-
tacting Sierra Customer Service.
Technical Assistance
If you encounter a problem with your flow meter, review the configura-
tion information for each step of the installation, operation and set up pro-
cedures. Verify that your settings and adjustments are consistent with fac-
tory recommendations. Refer to Chapter 4, Troubleshooting, for specific
information and recommendations.
If the problem persists after following the troubleshooting procedures
outlined in Chapter 4, contact Sierra Instruments, Technical Support at
[phone] or [phone] between 8:00 a.m. and 5:00 p.m. PST.
When calling Technical Support, have the following information on
hand:
•the flow range, serial number and Sierra order number (all
marked on the meter nameplate)
•the problem you are encountering and any corrective action
taken
•application information (gas, pressure, temperature and pip-
ing configuration)

Series 240/241 Instruction Manual Chapter 1 Introduction
IM-24 1-3
How the Innova-Flo Vortex Flow Meter Operates
Figure 1-1. Series 240 In-Line Vortex Flow Meter
Sierra Series 240 and 241 Innova-Flo™Vortex Flow Meters use a unique
velocity sensor head to monitor volumetric flow rate. The built-in flow
computer calculates mass flow rate based on a constant value of fluid
density stored in the instrument’s memory. To measure fluid velocity,
the flow meter incorporates a bluff body (shedder bar) in the flow
stream, and the velocity sensor measures the frequency of vortices
created by the shedder bar. The velocity sensor head is located down-
stream of the shedder bar within the flow body.
Velocity Measurement
The Innova-Flo vortex velocity sensor is a patented mechanical design
that minimizes the effects of pipeline vibration and pump noise, both of
which are common error sources in flow measurement with vortex flow
meters. The velocity measurement is based on the well-known Von Kar-
man vortex shedding phenomenon. Vortices are shed from a shedder bar,
and the vortex velocity sensor located downstream of the shedder bar
senses the passage of these vortices. This method of velocity measurement
has many advantages including inherent linearity, high turndown, reliabil-
ity and simplicity.

Chapter 1 Introduction Series 240/241 Instruction Manual
1-4 IM-24
Vortex Shedding Frequency
Von Karman vortices form downstream of a shedder bar into two distinct
wakes. The vortices of one wake rotate clockwise while those of the oth-
er wake rotate counterclockwise. Vortices generate one at a time, alter-
nating from the left side to the right side of the shedder bar. Vortices in-
teract with their surrounding space by over-powering every other nearby
swirl on the verge of development. Close to the shedder bar, the distance
(or wave length) between vortices is always constant and measurable.
Therefore, the volume encompassed by each vortex remains constant, as
shown below. By sensing the number of vortices passing by the velocity
sensor, the Innova-Flo™Vortex Flow Meter computes the total fluid vo-
lume.
Vortex shedder bar
Flow
Vortices
Velocity sensor
Constant
wave length
Figure 1-2. Measurement Principle of Vortex Flow Meters
Vortex Frequency Sensing
The velocity sensor incorporates a piezoelectric element that senses the
vortex frequency. This element detects the alternating lift forces pro-
duced by the Von Karman vortices flowing downstream of the vortex
shedder bar. The alternating electric charge generated by the piezoelec-
tric element is processed by the transmitter’s electronic circuit to obtain
the vortex shedding frequency. The piezoelectric element is highly sensi-
tive and operates over a wide range of flows, pressures and temperatures.

Series 240/241 Instruction Manual Chapter 1 Introduction
IM-24 1-5
Re = ρV D
μ
St = f d
V
Flow Velocity Range
To ensure trouble-free operation, vortex flow meters must be correctly
sized so that the flow velocity range through the meter lies within the
measurable velocity range (with acceptable pressure drop) and the linear
range.
The measurable range is defined by the minimum and maximum velocity
using the following table.
Gas Liquid
Vmin 25
ρ
ft/s
1 ft/s
English
ρ (lb/ft3)
Vmax 300 ft/s 30 ft/s
Vmin 37
ρ
m/s
0.3 m/s
Metric
ρ (kg/m3)
Vmax 91 m/s 9.1 m/s
The pressure drop for series 241 insertion meters is negligible. The
pressure drop for series 240 in-line meters is defined as:
ΔP = .00024 ρV2 English units (ΔP in psi, ρin lb/ft3, V in ft/sec)
ΔP = .000011 ρV2 Metric units (ΔP in bar, ρin kg/m3, V in m/sec)
The linear range is defined by the Reynolds number. The Reynolds num-
ber is the ratio of the inertial forces to the viscous forces in a flowing flu-
id and is defined as:
Where
Re = Reynolds Number
ρ= mass density of the fluid being measured
V = velocity of the fluid being measured
D = internal diameter of the flow channel
μ= viscosity of the fluid being measured
The Strouhal number is the other dimensionless number that quantifies the
vortex phenomenon. The Strouhal number is defined as:
Where
St = Strouhal Number
f = frequency of vortex shedding
d = shedder bar width
V = fluid velocity

Chapter 1 Introduction Series 240/241 Instruction Manual
1-6 IM-24
As shown below, Innova-Flo™Vortex Flow Meters exhibit a constant
Strouhal number across a large range of Reynolds numbers, indicating a
consistent linear output over a wide range of flows and fluid types. Be-
low this linear range, the intelligent electronics in Innova-Flo automati-
cally corrects for the variation in the Strouhal number. Innova-Flo’s
smart electronics correct for this non-linearity by calculating the Rey-
nolds number based on constant values of the fluid’s density and viscosi-
ty stored in the instrument’s memory. Innova-Flo Vortex Flow Meters
automatically correct down to a Reynolds number of 5,000.
0.3
0.2
0.1
0.0 34
10
Linear range
Reynolds Number, Re
Strouhal Number, St
10 5 10 108 106107
5000
Corrected range
Figure 1-3. Reynolds Number Range for the Innova-Flo Meter

Series 240/241 Instruction Manual Chapter 1 Introduction
IM-24 1-7
Flow Meter Configurations
Innova-Flo™ Vortex Flow Meters are available in two configurations:
•Series 240 in-line flow meter (replaces a section of the pipeline)
•Series 241 insertion flow meter (requires a “cold” tap or a “hot” tap
into an existing pipeline)
Both the in-line and insertion configurations are similar in that they both
use identical electronics and have similar sensor heads. Besides installa-
tion differences, the main difference between an in-line flow meter and
an insertion flow meter is their method of measurement.
For an in-line vortex flow meter, the shedder bar is located across the en-
tire diameter of the flow body. Thus, the entire pipeline flow is included
in the vortex formation and measurement. The sensing head, which di-
rectly measures velocity is located just downstream of the shedder bar.
An insertion vortex flow meter has its sensing head at the end of a 0.750
inch diameter tubular stem. The stem is inserted into the pipe until the
sensing head is properly located in the pipe’s cross section. The sensing
head fits through any entry port with an 1.875 inch minimum internal di-
ameter.
The sensing head of an insertion vortex flow meter directly monitors the
velocity at a point in the cross-sectional area of a pipe, duct, or stack (re-
ferred to as “channels”). The velocity at a point in the pipe varies as a func-
tion of the Reynolds number. The insertion vortex flow meter computes the
Reynolds number based on constant values of the fluid’s density and vis-
cosity stored in its memory and then computes the total flow rate in the
channel. The output signal of insertion meters is the total flow rate in the
channel. The accuracy of the total flow rate computation depends on adhe-
rence to the piping installation requirements given in Chapter 2. If adhe-
rence to those guidelines cannot be met, contact the factory for specific in-
stallation advice.
Flow Meter Electronics
Innova-Flo electronics are available mounted directly to the flow body,
or remotely mounted. The electronics housing may be used indoors or
outdoors, including wet environments. The instrument requires 4-20 mA
loop power (12 to 36 VDC). One analog output signal is available for
your choice of volumetric flow rate or mass flow rate. A pulse output is
available for totalization.

Chapter 1 Introduction Series 240/241 Instruction Manual
1-8 IM-24
The meter includes a local 2 x 16 character LCD display housed within
the enclosure. Local operation and reconfiguration is accomplished using
six push buttons. For hazardous locations, the six push buttons can be
operated through the sealed enclosure using a hand-held magnet, thereby
not compromising the integrity of the hazardous location certification.
The electronics include nonvolatile memory that stores all configuration
information. The memory allows the flow meter to function immediately
upon power up, or after an interruption in power.

Series 240/241 Instruction Manual Chapter 2 Installation
IM-24 2-1
Chapter 2 Installation
Installation Overview
Innova-Flo™ meter installations are simple and straightforward. Both the Se-
ries 240 In-Line and Series 241 Insertion type flow meter installations are
covered in this chapter. After reviewing the installation requirements given
below, see page 2-3 for Series 240 installation instructions. See page 2-6 for
Series 241 installation instructions. Wiring instructions begin on page 2-19.
Flow Meter Installation Requirements
Before installing the flow meter, verify the installation site allows for these
considerations:
1. Line pressure and temperature will not exceed the flow meter
rating.
2. The location meets the required minimum number of pipe di-
ameters upstream and downstream of the sensor head as illu-
strated Figure 2-1.
3. Safe and convenient access with adequate overhead clearance
for maintenance purposes.
4. Verify that the cable entry into the instrument meets the specific
standard required for hazardous area installations.
5. For remote installations, verify the supplied cable length is suf-
ficient to connect the flow meter sensor to the remote electron-
ics.
Also, before installation check your flow system for anomalies such as:
•leaks
•valves or restrictions in the flow path that could create disturbances in
the flow profile that might cause unexpected flow rate indications
Warning!
Consult the flow meter namep-
late for specific flow meter ap-
provals before any hazardous
location installation.

Chapter 2 Installation Series 240/241 Instruction Manual
2-2 IM-24
Unobstructed Flow Requirements
Select an installation site that will minimize possible distortion in the flow
profile. Valves, elbows, control valves and other piping components may
cause flow disturbances. Check your specific piping condition against the ex-
amples shown below. In order to achieve accurate and repeatable perfor-
mance install the flow meter using the recommended number of straight run
pipe diameters upstream and downstream of the sensor.
Note: For liquid applications in vertical pipes, avoid installing with flow in
the downward direction because the pipe may not be full at all points.
Choose to install the meter with flow in the upward direction if possible.
Flow meter
AB
Example 1.
One 90° elbow before meter
C' Flow meter
AB
C
Flow conditioner
(if used)
Example 2.
Two 90° elbows before meter in one plane
C' Flow meter
AB
C
Flow conditioner
(if used)
Example 3.
Two 90° elbows before meter out of plane (if three
90° bends present, double recommended length)
Flow meter
AB
Example 4.
Reduction before meter
C' C
Flow conditioner
(if used)
Flow meter
AB
C' C
Flow conditioner
(if used)
Example 5.
Expansion before meter
Example 6.
Regulator or valve partially closed before meter
(If valve is always wide open, base length
requirements on fitting directly preceding it)
Flow meter
AB
C' C
Flow conditioner (if used)
Minimum Required
Upstream Diameters Minimum Required Downstream Diameters
No Flow
Conditioner With Flow Conditioner No Flow Conditioner With Flow Conditioner
Example A A C C´ B B
1 10 D N/A N/A N/A 5 D 5 D
2 15 D 10 D 5 D 5 D 5 D 5 D
3 25 D 10 D 5 D 5 D 10 D 5 D
4 10 D 10 D 5 D 5 D 5 D 5 D
5 20 D 10 D 5 D 5 D 5 D 5 D
6 25 D 10 D 5 D 5 D 10 D 5 D
D = Internal diameter of channel. N/A = Not applicable
Figure 2-1. Recommended Pipe Length Requirements for Installation, Series 240 and 241

Series 240/241 Instruction Manual Chapter 2 Installation
IM-24 2-3
Series 240 In-Line Flow Meter Installation
Install the Series 240 In-Line Flow Meter between two conventional pipe
flanges as shown in Figures 2-3 and 2-4. Table 2-1 provides the recommend-
ed minimum stud bolt lengths for wafer-style meter body size and different
flange ratings.
The meter inside diameter is equal to the same size nominal pipe ID in sche-
dule 80. For example, a 2” meter has an ID of 1.939” (2” schedule 80). Do
not install the meter in a pipe with an inside diameter smaller than the
inside diameter of the meter. For schedule 160 and higher pipe, a special
meter is required. Consult the factory before purchasing the meter.
Series 240 Meters require customer-supplied gaskets. When selecting gasket
material make sure that it is compatible with the process fluid and pressure
ratings of the specific installation. Verify that the inside diameter of the
gasket is larger than the inside diameter of the flow meter and adjacent pip-
ing. If the gasket material extends into the flow stream, it will disturb the
flow and cause inaccurate measurements.
Flange Bolt Specifications
Stud Bolt Lengths for Each Flange Rating (inches)
Line Size Class 150 Class 300 Class 600
1 inch 6.00 7.00 7.50
1.5 inch 6.25 8.50 9.00
2 inch 8.50 8.75 9.50
3 inch 9.00 10.00 10.50
4 inch 9.50 10.75 12.25
Table 2-1. Minimum Recommended Stud Bolt Lengths for Wafer Meters
The required bolt load for sealing the gasket joint is affected by several ap-
plication-dependent factors, therefore the required torque for each application
may be different. Refer to the ASME Pressure Vessel Code guidelines for
bolt tightening standards.
1
2
34
1
2
34
5
67
8
15
9
3
7
11
2
6
10
4
8
12
4-bolt 8-bolt 12-bolt
Figure 2-2. Flange Bolt Torquing Sequence

Chapter 2 Installation Series 240/241 Instruction Manual
2-4 IM-24
Wafer-Style Flow Meter Installation
Install the wafer-style meter between two conventional pipe flanges of the
same nominal size as the flow meter. If the process fluid is a liquid, make
sure the meter is located where the pipe is always full. This may require lo-
cating the meter at a low point in the piping system. Note: Vortex flow me-
ters are not suitable for two-phase flows (i.e., liquid and gas mixtures). For
horizontal pipelines having a process temperature above 300° F, mount the
meter at a 45 or 90-degree angle to avoid overheating the electronics enclo-
sure. To adjust the viewing angle of the enclosure or display/keypad, see
page 2-17.
Figure 2-3. Wafer-Style Flow Meter Installation
When installing the meter make sure the section marked “inlet” is positioned up-
stream of the outlet, facing the flow. This ensures that the sensor head is posi-
tioned downstream of the vortex shedder bar and is correctly aligned to the flow.
Installing the meter opposite this direction will result in completely inaccurate
flow measurement. To install the meter:
1. Turn off the flow of process gas, liquid or steam. Verify that the line is
not pressurized. Confirm that the installation site meets the required min-
imum upstream and downstream pipe diameters.
2. Insert the studs for the bottom side of the meter body between the pipe
flanges. Place the wafer-style meter body between the flanges with the end
stamped “inlet” facing flow. Center the meter body inside the diameter
with respect to the inside diameter of the adjoining piping.
3. Position the gasket material between the mating surfaces. Make sure both
gaskets are smooth and even with no gasket material extending into the
flow profile. Obstructions in the pipeline will disturb the flow and cause
inaccurate measurements.
4. Place the remaining studs between the pipe flanges. Tighten the nuts in the
sequence shown in Figure 2-2. Check for leaks after tightening the flange
bolts.
Caution!
When using toxic or cor-
rosive gases, purge the
line with inert gas for a
minimum of four hours
at full gas flow before
installing the flow meter.

Series 240/241 Instruction Manual Chapter 2 Installation
IM-24 2-5
Flange-Style Flow Meter Installation
Install the flange-style meter between two conventional pipe flanges of the
same nominal size as the flow meter. If the process fluid is a liquid, make
sure the meter is located where the pipe is always full. This may require lo-
cating the meter at a low point in the piping system. Note: Vortex flow me-
ters are not suitable for two-phase flows (i.e., liquid and gas mixtures). For
horizontal pipelines having a process temperature above 300° F, mount the
meter at a 45 or 90-degree angle to avoid overheating the electronics enclo-
sure. To adjust the viewing angle of the enclosure or display/keypad, see
page 2-17.
Figure 2-4. Flange-Style Flow Meter Installation
When installing the meter make sure the flange marked “inlet” is positioned up-
stream of the outlet flange, facing the flow. This ensures that the sensor head is
positioned downstream of the vortex shedder bar and is correctly aligned to the
flow. Installing the meter opposite this direction will result in completely inaccu-
rate flow measurement. To install the meter:
1. Turn off the flow of process gas, liquid or steam. Verify that the line is
not pressurized. Confirm that the installation site meets the required min-
imum upstream and downstream pipe diameters.
2. Seat the meter level and square on the mating connections with the flange
marked “inlet” facing the flow. Position a gasket in place for each side. Make
sure both gaskets are smooth and even with no gasket material extending into
the flow profile. Obstructions in the pipeline will disturb the flow and cause
inaccurate measurements.
3. Install bolts in both process connections. Tighten the nuts in the sequence
shown in Figure 2-2. Check for leaks after tightening the flange bolts.
Caution!
When using toxic or cor-
rosive gases, purge the
line with inert gas for a
minimum of four hours
at full gas flow before
installing the flow meter.

Chapter 2 Installation Series 240/241 Instruction Manual
2-6 IM-24
Series 241 Insertion Flow Meter Installation
Prepare the pipeline for installation using either a cold tap or hot tap method
described on the following pages. Refer to a standard code for all pipe tap-
ping operations. The following tapping instructions are general in nature and
intended for guideline purposes only. Before installing the meter, review the
mounting position and isolation value requirements given below.
Mounting Position
Allow clearance between the electronics enclosure top and any other obstruc-
tion when the meter is fully retracted.
Isolation Valve Selection
An isolation valve is available as an option with Series 241 meters. If you
supply the isolation valve, it must meet the following requirements:
1. A minimum valve bore diameter
of 1.875 inches is required, and
the valve’s body size should be
two inches. Normally, gate
valves are used.
2. Verify that the valve’s body and
flange rating are within the flow
meter’s maximum operating
pressure and temperature.
3. Choose an isolation valve with
at least two inches existing between the flange face and the gate portion
of the valve. This ensures that the flow meter’s sensor head will not in-
terfere with the operation of the isolation valve.
1.875-inch min.
valve bore
2-inch min.
2-inch
valve size
Isolation Valve Requirements

Series 240/241 Instruction Manual Chapter 2 Installation
IM-24 2-7
Cold Tap Guidelines
Refer to a standard code for all pipe tapping operations. The following tap-
ping instructions are general in nature and intended for guideline purposes
only.
1. Turn off the flow of process gas, liquid or steam. Verify that the line is
not pressurized.
2. Confirm that the installation site meets the minimum upstream and
downstream pipe diameter requirements. See Figure 2-1.
3. Use a cutting torch or sharp cutting tool to tap into the pipe. The pipe
opening must be at least 1.875 inches in diameter. (Do not attempt to in-
sert the sensor probe through a smaller hole.)
4. Remove all burrs from the tap. Rough edges may cause flow profile dis-
tortions that could affect flow meter accuracy. Also, obstructions could
damage the sensor assembly when inserting into the pipe.
5. After cutting, measure the thickness of the cut-out and record this num-
ber for calculating the insertion depth.
6. Weld the flow meter pipe connec-
tion on the pipe. Make sure this
connection is within ± 5° perpen-
dicular to the pipe centerline.
7. Install the isolation valve (if
used).
8. When welding is complete and all fittings are installed, close the isola-
tion valve or cap the line. Run a static pressure check on the welds. If
pressure loss or leaks are detected, repair the joint and re-test.
9. Connect the meter to the pipe process connection.
10. Calculate the sensor probe insertion depth as described on the following
pages. Insert the sensor probe into the pipe.
Caution!
When using toxic or
corrosive gases, purge
the line with inert gas
for a minimum of four
hours at full gas flow
before installing the
flow meter.
Warning!
All flow meter connec-
tions, isolation valves and
fittings for cold tapping
must have the same or
higher pressure rating as
the main pipeline.