SIGMA TEK PIM 041-W User manual

Date of creation: 16.07.2020 Version date: 14.04.2021 Article number: 01-232-041-WE
PIM 041-W
Panel Interface Module
Operating Manual

Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: [phone]
Fax: [phone]
Email: [email protected]
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2020
SIGMATEK GmbH & Co KG
Translation from German
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or
distributed in any form (print, photocopy, microfilm or in any other process) without express permission.
We reserve the right to make changes in the content without notice. SIGMATEK GmbH & Co KG is not responsible
for technical or printing errors in this handbook and assumes no responsibility for damages that occur through
its use.

PANEL INTERFACE MODULE PIM 041-W
Panel Interface Module PIM 041-W
The Panel Interface Module (PIM) is an attachable CPU for SIGMATEK touch panels (TP).
This module operates with a high-performance Intel Celeron dual-core processor.
The available interfaces are used, among other things, to forward process data. A generous
M.2 hard drive serves as the storage medium for the operating system, application and
application data.
In combination with a SIGMATEK TP, the 2 components form a multi-touch operating panel
for visualizing, operating and monitoring automated processes. The SIGMATEK TPs are
available in various models and a can be mounted or exchanged in the field with minimal
effort.
14.04.2021 Page 1

PIM 041-W PANEL INTERFACE MODULE
Table of Contents
1 Introduction 4
1.1 Target Group/Purpose of this Operating Manual 4
1.2 Important Reference Documentation 4
1.3 Contents of Delivery 4
2 Basic Safety Guidelines 5
2.1 Symbols Used 5
2.2 Disclaimer 7
2.3 General Safety Guidelines 8
3 Standards and Guidelines 10
3.1 Guidelines 10
3.1.1 EU Conformity Declaration 10
4 Technical Data 11
4.1 Performance Data 11
4.2 Electrical Requirements 12
4.3 Environmental Conditions 13
4.4 Miscellaneous 14
5 Interfaces 15
5.1 Front Connectors 15
5.1.1 X1: Supply (4-pin Phoenix RM 3.5) 15
5.1.2 X9: Panel Interface Connector 15
5.2 Left Side Connectors 16
5.2.1 X2: DisplayPort Output V1.2a 16
5.2.2 X3, X4: Ethernet 1, 2 10/100/1000 Mbit/s (RJ45) 17
5.2.3 X5-X8: USB 2.0 (Type A) 17
5.3 Applicable Connectors 17
6 Mechanical Dimensions 18
Page 2 14.04.2021

PANEL INTERFACE MODULE PIM 041-W
7 Assembly/Installation 19
7.1 Check Contents of Delivery 19
7.2 Installation 19
8 Wiring 20
8.1 Note 20
8.2 Grounding 21
8.3 Shielding 21
8.4 ESD Protection 22
8.5 USB Interface 22
9 Transport/Storage 23
10 Storage 24
11 Maintenance 25
11.1 Service 25
11.2 Repair 25
12 Buffer Battery 26
12.1 Data Retention Battery Change 27
12.2 Exchanging the Battery 27
13 Modularity 29
13.1 Removing the PIM from the Touch Panel 29
13.2 Mounting the PIM onto the Touch Panel 30
13.2.1 Calibrating the Touch Screen 31
14 Disposal 32
15 Accessories 33
15.1 Battery 33
14.04.2021 Page 3

PIM 041-W PANEL INTERFACE MODULE
1 Introduction
1.1 Target Group/Purpose of this Operating Manual
This operating manual contains all information required for the operation of the product.
This operating manual is intended for:
lProject planners
lTechnicians
lCommissioning engineers
lMachine operators
lMaintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found on
our website www.sigmatek-automation.com.
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
1.2 Important Reference Documentation
lTP XX61
This and additional documents can be downloaded from our website or obtained through
support.
1.3 Contents of Delivery
1x PIM 041-W
1x 4-pin Phoenix connector plug
4x M3 TX10 Torx screws
Page 4 14.04.2021

PANEL INTERFACE MODULE PIM 041-W
2 Basic Safety Guidelines
2.1 Symbols Used
The following symbols are used in the operator documentation for warning and danger
messages, as well as informational notes.
DANGER
Danger indicates that death or serious injury will occur, if the specified
measures are not taken.
To avoid death or serious injuries, observe the all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the specified
measures are not taken.
To avoid death or serious injuries, observe the all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
14.04.2021 Page 5

PIM 041-W PANEL INTERFACE MODULE
CAUTION
Caution indicates that moderate to slight injury can occur, if the
specified measures are not taken.
To avoid moderate to slight injuries, observe the all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou
légères.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
DANGER
Electrical voltage
Tension électrique
CAUTION
Danger for ESD-sensitive components.
Les signes de danger pour les composants sensibles aux décharges
électrostatiques.
INFORMATION
INFORMATION
Provides important information on the product, handling or
relevant sections of the documentation, which require particular
attention.
Page 6 14.04.2021

PANEL INTERFACE MODULE PIM 041-W
2.2 Disclaimer
INFORMATION
The contents of this operating manual were prepared with the greatest
care. However, deviations cannot be ruled out. This operating manual is
regularly checked and required corrections are included in the subsequent
versions. The machine manufacturer is responsible for the proper
assembly, as well as device configuration. The machine operator is
responsible for safe handling, as well as proper operation.
The current operating manual can be found on our website. If necessary,
contact our support.
Subject to technical changes, which improve the performance of the
devices. The following operating manual is purely a product description. It
does not guarantee properties under the warranty.
Please thoroughly read the corresponding documents and this operating
manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused
through, non-compliance with these instructions or applicable
regulations.
14.04.2021 Page 7

PIM 041-W PANEL INTERFACE MODULE
2.3 General Safety Guidelines
The Safety Guidelines in the other sections of this operating manual must be observed. These
instructions are visually emphasized by symbols.
INFORMATION
According to EU Guidelines, the operating manual is a component of a
product.
This operating manual must therefore be accessible in the vicinity of the
machine since it contains important instructions.
This operating manual should be included in the sale, rental or transfer of
the product, or its online availability indicated.
Maintain this operating manual in readable condition and keep it
accessible for reference.
Regarding the requirements for Safety and health connected to the use of
machines, the manufacturer must perform a risk assessment in
accordance with machine guidelines 2006/42/EG before introducing a
machine to the market. Before commissioning this product, check that
conformance with the provisions of the 2006/42/EG guidelines is correct.
As long as the machine with which the product should be used does not
comply with the guideline, operating this product is prohibited.
Operate the unit with devices and accessories approved by SIGMATEK
only.
Page 8 14.04.2021