SIGMA TEK HMI-Link G2 Device User manual

HMI-Link G2
Device
PC 301-E12
Operating Manual
Date of creation: 04.06.2020
Version date: 06.08.2020
Article number: 01-310-301-E12-E

Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: [phone]
Fax: [phone]
Email: [email protected]
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2020
SIGMATEK GmbH & Co KG
Translation from German
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or dis-
tributed in any form (print, photocopy, microfilm or in any other process) without express permission.
We reserve the right to make changes in the content without notice. SIGMATEK GmbH & Co KG is not responsible for
technical or printing errors in this handbook and assumes no responsibility for damages that occur through its use.

HMI-LINK G2 DEVICE PC 301-E12
06.08.2020 Page 1
HMI-Link G2 Device PC 301-E12
Using HMI-Link G2 Device allows HMI-Link G2 display units to be connected with a
SIGMATEK IPC. This allows the transmission of USB and display signals up to 100 m.

PC 301-E12 HMI-LINK G2 DEVICE
Page 2 06.08.2020
Contents
1Introduction............................................................................. 5
1.1 Target Group/Purpose of this Operating Manual ......................5
1.2 Important Reference Documentation .........................................5
1.3 Contents of Delivery.....................................................................5
2Basic Safety Guidelines......................................................... 6
2.1 Symbols Used...............................................................................6
2.2 Disclaimer......................................................................................8
2.3 General Safety Guidelines...........................................................9
3Norms and Guidelines...........................................................10
3.1 Guidelines....................................................................................10
3.1.1 EU Declaration of Conformity............................................................10
4Technical Data .......................................................................11
4.1 Performance Data.......................................................................11
4.2 Electrical Requirements.............................................................11
4.3 Environmental Conditions.........................................................12
4.4 Miscellaneous .............................................................................12
5Mechanical Dimensions........................................................13
6Connector Layout..................................................................14
6.1 X1: Display port IN......................................................................15
6.2 X2: USB 2.0 IN (Type B)..............................................................15

HMI-LINK G2 DEVICE PC 301-E12
06.08.2020 Page 3
6.3 X3: HMI Local OUT (HMI-Link G2, Mini-I/O)..............................16
6.4 X4 Supply voltage.......................................................................16
6.4.1 Applicable Connectors...................................................................... 16
7Status Displays......................................................................17
8Assembly/Installation ...........................................................18
8.1 Check Contents of Delivery.......................................................18
8.2 Mounting Instructions................................................................18
8.3 Installation...................................................................................19
8.4 Mounting Material .......................................................................19
8.5 Minimum Clearance to the Next Components.........................20
9Wiring Guidelines..................................................................21
9.1 Ground.........................................................................................21
9.2 Shielding......................................................................................22
9.3 ESD Protection............................................................................22
10 HMI-Link G2 Wiring...............................................................23
10.1 Shielding......................................................................................23
10.2 HMI-Link G2 Cable Specification...............................................24
10.2.1 Tyco Mini I/O Pin Assignment........................................................... 24
10.3 HMI-Link G2 Cable Routing .......................................................24
11 Transport/Storage.................................................................25
12 Maintenance...........................................................................26

PC 301-E12 HMI-LINK G2 DEVICE
Page 4 06.08.2020
12.1 Service.........................................................................................26
12.2 Repair...........................................................................................26
13 Disposal..................................................................................27

HMI-LINK G2 DEVICE PC 301-E12
06.08.2020 Page 5
1 Introduction
1.1 Target Group/Purpose of this Operating Manual
This operating manual contains all information required to operate this product.
This operating manual is intended for:
•Project planners
•Technicians
•Commissioning engineers
•Machine operators
•Maintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found on
our website www.sigmatek-automation.com
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
1.2 Important Reference Documentation
This and additional documents can be downloaded from our website or obtained through
SIGMATEK Support.
1.3 Contents of Delivery
1x HMI-Link G2 Device PC 301-E12

PC 301-E12 HMI-LINK G2 DEVICE
Page 6 06.08.2020
2 Basic Safety Guidelines
2.1 Symbols Used
The following symbols are used in the operator documentation for warning and danger mes-
sages, as well as informational notes:
DANGER
Danger indicates that death or serious injury will occur, if the specified
measures are not taken.
To avoid death or serious injuries, observe the all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures graves,
voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the specified
measures are not taken.
To avoid death or serious injuries, observe the all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures graves,
voire mortelles.
CAUTION
Caution indicates that moderate to slight injury can occur, if the specified
measures are not taken.
To avoid moderate to slight injuries, observe the all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou lé-
gères.
Respectez toutes les consignes pour éviter des blessures graves,
voire mortelles.
INFORMATION
Provides important information on the product, handling or relevant sections
of the documentation, which require attention.

HMI-LINK G2 DEVICE PC 301-E12
06.08.2020 Page 7
Danger for ESD-sensitive components. Les signes de danger pour les com-
posants sensibles aux décharges électrostatiques.

PC 301-E12 HMI-LINK G2 DEVICE
Page 8 06.08.2020
2.2 Disclaimer
The contents of this operating manual were prepared with the greatest care.
However, deviations cannot be ruled out. This operating manual is regularly
checked and required corrections are included in the subsequent versions.
The machine manufacturer is responsible for the proper assembly, as well
as device configuration. The machine operator is responsible for safe han-
dling, as well as proper operation.
The current operating manual can be found on our website. If necessary,
contact our support.
Subject to technical changes,which improve the performance of the devices.
The following operating manual is purely a product description. It does not
guarantee properties under the warranty.
Please thoroughly read the corresponding documentation and this operating
manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused through
non-compliance with these instructions or applicable regulations.