SIGMA TEK KL 180 User manual

KL 180
S-DIAS 0 V Potential Distributor
Module
Instruction Manual
Date of creation: 30.07.2013
Version date: 26.07.2023
Article number: 20-024-180-E

Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: [phone]
Fax: [phone]
Email: [email protected]
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2013
SIGMATEK GmbH & Co KG
Translation of the Original Instructions
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or
distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.
We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not
responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur
through use of this handbook.

S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE KL 180
26.07.2023 Page 1
S-DIAS 0 V Potential Distributor Module KL 180
with 18 0 V terminals
The KL 180 S-DIAS 0 V potential distributor module has 18 terminals.
The voltage tap is possible without an additional series terminal.

KL 180 S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE
Page 2 26.07.2023
Contents
1Introduction............................................................................. 4
1.1 Target Group/Purpose of this Operating Manual......................4
1.2 Important Reference Documentation .........................................4
1.3 Contents of Delivery.....................................................................4
2Basic Safety Directives .......................................................... 5
2.1 Symbols Used...............................................................................5
2.2 Disclaimer......................................................................................7
2.3 General Safety Directives ............................................................8
2.4 Software/Training .........................................................................9
3Standards and Directives......................................................10
3.1 Directives.....................................................................................10
3.1.1 EU Conformity Declaration................................................................10
4Type Plate...............................................................................11
5Technical Data .......................................................................12
5.1 0 V Supplies.................................................................................12
5.2 Electrical Requirements.............................................................12
5.3 Miscellaneous .............................................................................14
5.4 Environmental Conditions.........................................................14
6Mechanical Dimensions........................................................15
7Connector Layout..................................................................16

S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE KL 180
26.07.2023 Page 3
7.1 Applicable Connectors...............................................................17
7.2 Label Field...................................................................................18
8Wiring.....................................................................................19
8.1 Wiring Example...........................................................................19
9Assembly/Installation ...........................................................20
9.1 Check Contents of Delivery.......................................................20
9.2 Mounting......................................................................................21
10 Transport/Storage .................................................................23
11 Storage...................................................................................23
12 Maintenance...........................................................................24
12.1 Service.........................................................................................24
12.2 Repair...........................................................................................24
13 Disposal .................................................................................24

KL 180 S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE
Page 4 26.07.2023
1 Introduction
1.1 Target Group/Purpose of this Operating Manual
This operating manual contains all information required for the operation of the product.
This operating manual is intended for:
•Project planners
•Technicians
•Commissioning engineers
•Machine operators
•Maintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found
on our website www.sigmatek-automation.com.
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
1.2 Important Reference Documentation
This and additional documents can be downloaded from our website or obtained through
support.
1.3 Contents of Delivery
1x KL 180

S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE KL 180
26.07.2023 Page 5
2 Basic Safety Directives
2.1 Symbols Used
The following symbols are used in the operator documentation for warning and danger
messages, as well as informational notes:
DANGER
Danger indicates that death or serious injury will occur, if the
specified measures are not taken.
To avoid death or serious injuries, observe all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the
specified measures are not taken.
To avoid death or serious injuries, observe all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
CAUTION
Caution indicates that moderate to slight injury can occur, if the
specified measures are not taken.
To avoid moderate to slight injuries, observe all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou
légères.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.

KL 180 S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE
Page 6 26.07.2023
INFORMATION
Information
Provides important information on the product, handling or
relevant sections of the documentation, which require
attention.

S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE KL 180
26.07.2023 Page 7
2.2 Disclaimer
INFORMATION
The contents of this operating manual were prepared with the greatest
care. However, deviations cannot be ruled out. This operating manual
is regularly checked and required corrections are included in the
subsequent versions. The machine manufacturer is responsible for the
proper assembly, as well as device configuration. The machine
operator is responsible for safe handling, as well as proper operation.
The current operating manual can be found on our website. If
necessary, contact our support.
Subject to technical changes, which improve the performance of the
devices. The following operating manual is purely a product
description. It does not guarantee properties under the warranty.
Please thoroughly read the corresponding documents and this
operating manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused
through, non-compliance with these instructions or applicable
regulations.

KL 180 S-DIAS 0 V POTENTIAL DISTRIBUTOR MODULE
Page 8 26.07.2023
2.3 General Safety Directives
The Safety Directives in the other sections of this operating manual must be observed.
These instructions are visually emphasized by symbols.
INFORMATION
According to EU Directives, the operating manual is a component of a
product.
This operating manual must therefore be accessible in the vicinity of
the machine since it contains important instructions.
This operating manual should be included in the sale, rental or transfer
of the product, or its online availability indicated.
Regarding the requirements for Safety and health connected to the use
of machines, the manufacturer must perform a risk assessment in
accordance with machine directives 2006/42/EG before introducing a
machine to the market.
Operate the unit with devices and accessories approved by
SIGMATEK only.