SignaMax 065-1063FS Series User manual

Model 065-1063FSx series
RS-232/422/485 to 100BaseFX
Device Server/Managed Media Converter
User’s Manual
(May 2007)

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
i
COPYRIGHT
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, whether electronic,
mechanical, photo copying, recording or otherwise, without the prior written
permission of the publisher.
FCC WARNING
This equipment has been tested and found to comply with the limits for a class
A device, pursuant to part 15 of FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a commercial installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communication. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case, the user
will be required to correct the interference at the user’s own expense.
CE
This is a Class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.
Take special note to read and understand all the content in the warning boxes:
Warning

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
ii
TABLE OF CONTENTS
1ABOUT THIS GUIDE.........................................................................1
1.1 Welcome............................................................................................................1
1.2 Purpose .............................................................................................................1
1.3 Terms/Usage .....................................................................................................1
1.4 Features.............................................................................................................1
1.5 Specifications ...................................................................................................2
1.6 Package Contents.............................................................................................3
2HARDWARE DESCRIPTION ............................................................4
2.1 Product Overview .............................................................................................4
2.2 Product Illustrations.........................................................................................4
3INSTALLATION.................................................................................5
3.1 Location.............................................................................................................5
3.2 Wall Mount Installation.....................................................................................5
3.3 DIN-rail Mount Installation ...............................................................................5
3.4 Powering On Unit..............................................................................................6
3.5 Connecting Fiber Cable ...................................................................................7
3.6 DB9 Male Connector Pin Assignments...........................................................7
3.7 Serial Connection .............................................................................................8
4LED INDICATORS ............................................................................9
5USER INTERFACE STARTUP........................................................10
5.1 Console Port Access............................................ Error! Bookmark not defined.
5.2 Telnet Access........................................................ Error! Bookmark not defined.
5.3 Web Access........................................................... Error! Bookmark not defined.
6CONFIGURATION MANAGEMENTERROR! BOOKMARK NOT DEFINED.
6.1 Menu-driven User Interface.................................. Error! Bookmark not defined.
6.1.1 System Information .............................................................. Error! Bookmark not defined.
6.1.2 DHCP Configuration ............................................................. Error! Bookmark not defined.
6.1.3 Operation Mode Menu.......................................................... Error! Bookmark not defined.
6.1.4 RS-232/422/485 UART Menu ................................................ Error! Bookmark not defined.
6.1.5 Monitor Menu ........................................................................ Error! Bookmark not defined.
6.1.6 TFTP Firmware Upgrade ...................................................... Error! Bookmark not defined.
6.1.7 SNMP Configuration............................................................. Error! Bookmark not defined.
6.1.8 System Restart...................................................................... Error! Bookmark not defined.
6.2 Command Line Interface...................................... Error! Bookmark not defined.
6.3 Web Graphic User Interface................................. Error! Bookmark not defined.
6.3.1 System Information .............................................................. Error! Bookmark not defined.

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
iii
6.3.2 Master Information ............................................................... Error! Bookmark not defined.
6.3.3 RS-232/422/485 Transfer Configuration.............................. Error! Bookmark not defined.
6.3.4 Serial Connect Status........................................................... Error! Bookmark not defined.
6.3.5 User Configuration ............................................................... Error! Bookmark not defined.
6.3.6 Firmware Download.............................................................. Error! Bookmark not defined.
6.3.7 SNMP Community Configuration ........................................ Error! Bookmark not defined.
6.3.8 IP Trap.................................................................................... Error! Bookmark not defined.
6.3.9 System Restart...................................................................... Error! Bookmark not defined.

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
1
1 About This Guide
1.1 Welcome
Thank you for selecting the Signamax 065-1063FSx series RS-232/422/485 to
100BaseFX Device Server / Managed Media Converter. This unit is designed to
provide an RS-232/422/485 connection over twisted-pair cable where the connected
devices have RS-232/422/485 interfaces. By enabling serial devices such as CNCs
and PLCs to instantly connect to an existing Ethernet/ Fast Ethernet network, the 065-
1063FSx series Serial-to-Ethernet Device Server / Managed Media Converter
represents a robust solution for devices controllers for MIS personnel. This product can
either be used as a Device Server or a Managed Media Converter.
1.2 Purpose
This guide discusses how to install and configure your 065-1063FSx series RS-
232/422/485 to 100BaseFX Device Server / Managed Media Converter.
1.3 Terms/Usage
In this guide, the term “Device Server / Managed Media Converter” (first letter upper
case) refers to your 065-1063FSx series RS-232/422/485 to 100BaseFX Device
Server / Managed Media Converter, and “device server / media converter” (first letter
lower case) refers to other device servers / media converters.
1.4 Features
•Device Server & Managed Media Converter Mode option
•Complies with EIA/TIA and IEEE standards
•100Mbps Fast Ethernet fiber port
•Supports 4-wire full duplex asynchronous serial data transmission (RS-422/485)
•Supports 2-wire half-duplex asynchronous serial data transmission (RS-485)
•Supports serial port asynchronous data rates up to 115.2 Kbps
•Extended distances up to 1.2 km (24 AWG) using RS-422/485
•Terminator feature improves signal quality and distance
•LEDs for ‘at-a-glance’ device status
•Wall mount or DIN-rail mountable installation
•Power range 9~32V DC
•FCC Class A & CE approved

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
2
1.5 Specifications
Standards: IEEE 802.3 (10BaseT Ethernet); IEEE 802.3u (100BaseTX/ Fast
Ethernet); EIA/TIA RS-232/422/485; EIA/TIA-5744
Ports: 1x Fiber; Singlemode / Multimode
1x 9-pin serial connector; D-sub, Male
Max. Distance: Fiber: Up to 120 km (> 15 km via special order)
Serial: 15 meters (RS-232)
1,200 meters (RS-422, RS-485)
Data Rates: Fiber: 100 Mbps
Serial: 115.2 kbps (asynchronous)
Signals: RS-232: TxD, RxD, CTS, RTS, DTR, DSR, RI, DCD, GND RS-
422: TxD+/-, RxD+/-, GND RS-485: Data+, Data-, GND
Configuration: Bits Per Second: 38400
Parity: None
Data bits: 8
Stop bits: 1
Flow Control: None
(The console connection is only available once the DIP switch 1 is
ON)
Switches: DIP 1: Enables / disables console / data communication mode
DIP 2: Enables / disables RS-232
DIP 3: Enables / disables RS- 422/485 (4-wire)
DIP 4: Enables / disables RS-485 (2-wire)
DIP 5: N/A
DIP 6: N/A
DIP 7: Enables / disables termination (TMR)
Power: External power adapter; 9~32V DC @800mA
Frequency: 47Hz to 63Hz
Environment: Operating: Temperature: 32°F to 122°F (0°C to 50°C)
Relative Humidity: 10% to 80%, non-condensing
Storage: Temperature: -4°F to 176°F (-20°C to 80°C)
Relative Humidity: 5% to 90%, non-condensing
Emissions: FCC Part 15 of Class A & CE approved
Dimensions: 4.30 x 3.54 x 1.18 in., L x W x H (109.2 x 90 x 30 mm)
Weight: 9.88 ounces (280 grams)

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
3
1.6 Package Contents
The package should include the following:
•One 065-1063FSx series Device Server / Managed Media Converter
•One power adapter (please check connector type and input power specification)
•Four self-adhesive pads
•DIN-rail Kit
•Screws for wall-mount installation
•Quick Installation Guide
•User’s Manual CD
•Serial IP Redirector software CD

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
4
2 Hardware Description
2.1 Product Overview
The Signamax 065-1063FSx series Device Server / Managed Media Converter
features complete Ethernet and TCP/IP network support that allows devices in industry
with RS-232/422/485 connectors such as milling machines, measurement instruments,
and robots to connect to LAN based automation. Other devices typically found on
campus networks such as card readers, code readers, lab equipment, medical
equipment, and other similar serial devices can now instantly migrate to a TCP/IP
network. Additionally, by deploying the device server mode, enable users to monitor
and manage up to 256 serial devices from single PC with the help of Serial IP
Redirector software for Device Server mode.
2.2 Product Illustrations
Front Panel
Rear Panel
Fiber LEDs RS-232/422/485,
DB9 Male
DIP Switches Power LED Power Connector

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
5
3 Installation
To install your Device Server / Managed Media converter, please see the following
procedures:
•Location
•DIN-rail Mounting
•Desktop Installation
•Powering On Unit
•Connecting Fiber Cables
•DB9 Male Connector Pin Assignment
•Serial Connection
3.1 Location
The location selected for installing the Device Server / Managed Media Converter may
greatly affect its performance. When selecting a site, we recommend considering the
following rules:
1. Install the Device Server / Managed Media Converter in a fairly cool and dry place.
See Technical Specifications for the acceptable temperature and humidity
operating ranges.
2. Install the Device Server / Managed Media Converter in a location free from strong
electromagnetic field generators (such as motors), vibration, dust, and direct
exposure to sunlight.
3. Leave at least 5cm of space at the front and rear of the unit for ventilation.
4. Affix the provided rubber pads to the bottom of the Device Server / Managed
Media Converter for grip, and to protect the case from scratching.
3.2 Wall Mount Installation
The 065-1063FSx series Device Server / Managed Media Converter can also be
installed by wall mounting. The backside casing provides space for two screws each
side. Identify the exact location at wall by placing the Device Server / Managed Media
Converter and marking the screw positions. Use the screws (included in the package)
and tighten them well to affix the Device Server / Managed Media Converter to the wall.
3.3 DIN-rail Mount Installation
The aluminum DIN-rail attachment plate should already be affixed to the back panel of
the Device Server / Managed Media Converter. If you need to attach the DIN-rail plate,
make sure that the stiff metal spring is situated towards the top. Attaching the Device
Server / Managed Media Converter to the DIN-rail is easy; just align, attach the top rail,
then press down and snap forward the Device Server / Managed Media Converter to
snap in the bottom rail, as shown in the figures below.

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
6
Use following steps set up the Device Server / Managed Media Converter:
•The surface must support at least 500 gm for the Device Server / Managed Media
Converter.
•The power outlet should be within 6 feet (1.82 meters) of the Device Server /
Managed Media Converter.
•Visually inspect the power adapter and make sure that it is properly connected.
Make sure that there is proper heat dissipation from and adequate ventilation around
the Device Server / Managed Media Converter. Do not place heavy objects on the
product.
Warning: Please exercise caution when using power tools. Also, do not
install this unit near damp or wet locations, or in close proximity to very hot
surfaces. These types of environments can have a detrimental effect on the
unit and cables.
3.4 Powering On Unit
The Device Server / Managed Media Converter uses an external power supply
providing 9~32V DC @ 0.8A from an AC power line at 50~60 Hz.
1. Insert the power cable plug directly into the receptacle located at the back of the
device.
2. Plug the power adapter into an available socket.
3. Check the rear-panel LEDs as the device is powered on to verify that the Power
LED is lit. If not, check that the power cable is correctly and securely plugged in.
NOTE: The RJ-45 port accepts both ‘straight-through’ and ‘cross-over’ Ethernet cables
without the need to re-configure the port.

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
7
3.5 Connecting Fiber Cable
When connecting fiber cable to a 100BaseFX port on the product, be sure the correct
type – ST, SC, or WDM (available via special order) - connector is used. Follow the
steps below to properly connect fiber cable:
1. Remove and keep the ST/SC/WDM port's rubber cover. When not connected to a
fiber cable, the rubber cover should be replaced to protect the optics.
2. Check that the fiber terminators are clean. You can clean the cable plugs by
wiping them gently with a clean tissue or cotton ball moistened with a little
ethanol. Dirty fiber terminators on fiber optic cables will impair the quality of the
light transmitted through the cable and lead to degraded performance on the port.
3. Connect one end of the cable to the ST/SC/WDM port on the Device Server /
Managed Media Converter and the other end to the ST/SC/WDM port on the
other device.
NOTE: When inserting the cable, be sure the tab on the plug clicks into position to
ensure that it is properly seated.
4. Check the corresponding port LED on the Device Server / Managed Media
Converter to be sure that the connection is valid. (Refer to the LED chart in next
section)
Warning: Because invisible laser radiation may be emitted from the
aperture of the fiber port when no cable is connected, avoid exposure
to laser radiation and do not stare into the open apertures.
3.6 DB9 Male Connector Pin Assignments
PIN RS-232
(Full-duplex)
RS-422/485
4-wire
(Full-duplex)
RS-485
2-wire
(Half-duplex)
1 DCD
2 RX RX- **DATA B(-)
3 TX TX-
4 DTR
5 GND GND GND
6 DSR
7 RTS RX+ **DATA A(+)
8 CTS TX+
9 RI
NOTE: Bi-directional RS-485 BUS line.

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
8
3.7 Serial Connection
This Device Server / Managed Media Converter features DIP switches on the rear
panel that sets the unit to the correct type of cable configuration to support connection
with a RS-232 / 422 / 485 device.
Definition of DIP Switches
No Dip description Default
1 ON: Console / OFF: Data OFF
2 RS-232 ON
3 RS-422 / 485 (4W) OFF
4 RS-485 (2W) OFF
5 NA OFF
6 NA OFF
7 TMR (Terminator) OFF
For setting the control function of the serial port, see the table below:
DIP 1 Serial Connection
ON RS-232 Console
OFF Data Communication
NOTE:
1. If using the console mode, turn DIP Switch 1 to the ON position. For data
communication from the serial device keep the switch in the OFF position. If the
switch is in the ON position, data communication will be blocked, and in the OFF
position, console port access will be blocked.
2. For some RS-422/485 devices which may not be designed to provide a DB-9
connection, please check the pin definition to connect the devices.
3. For the initial installation, you must use the console mode to setup the IP and
TCP port configuration with a RS-232 cable. Always use a cross-over cable; if
using a straight-through cable, you must use a “Null Modem” cable to use the
Telnet option.

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
9
4 LED Indicators
This device has LED indicators located at the front of the device. The LEDs have been
designed to provide easy at-a-glance network status and ‘real-time’ connectivity
information. Please see the chart below for a description of their functions:
LED Indicators
LED Condition Status
On (Green) Unit is receiving power
PWR Off Power off or failure
On (Green) Receiving data packets
Flashing (Green) Data packets are being transmitted or
received via the fiber port
LNK / ACT
Off Fiber optic cable is not connected
On (Green) Serial connector is attached and link signals
are being received
Flashing Data traffic is passing through the serial port
ACT
Off Serial port is idle or no link has been
established

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
10
5 User Interface Startup
There are two separate methods for configuring this Device Server / Managed Media
Converter for use. In the first section of this chapter, the Command line Interface (CLI)
or Menu-driven interface via the Console Port to set the device IP and TCP
configuration to monitor/managed the attached serial device via Serial IP Redirector
software. The second section will describe CLI or Menu-driven via Telnet configuration.
First, make the connection below:
DIP Switch 1 set to the ‘ON’ position
5.1 Console Port Access
The Device Server / Managed Media Converter is accessible via a terminal emulator
attached to the RS-232 console port. Please follow the steps below.
1. Attach the serial cable to COM port of computer and serial port of the device server.
2. Select Hyper Terminal from (start menu programs Accessories 
communication) a window will appear, assign the connection name. Then select
the correct available COM port (COM1 or COM2). After this enter the port settings
as described below:
Bits per second: 38400
Data bits: 8
Parity: None
Stop bits: 1
Flow Control: None
3. Once connection is established, you will see a log-in screen.
Device
Server
Female
Fem
ale
Computer
RS
-
232 Cable

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
11
4. Press ENTER and on the following screen, type the default username admin,
leave the password field blank since there is no default value and press ENTER to
proceed.
5. Select either CLI User Interface or Menu-driven Interface option by using the
associated number key or using the TAB key and pressing ENTER. A relevant
Main Menu screen appears.
The Device Server / Managed Media Converter is preset with a factory IP address
(192.168.0.254) that must be configured to the user’s individual IP address. It is
important to do this so that the device server / managed media converter doesn’t
conflict with other devices with the same defaults.
NOTE:
Prior to following the instructions for HyperTerminal Configuration, ensure that a serial
cable connection between the device server / managed media converter and
workstation exists.
Type the following command line to change the device IP address in CLI mode where
xxx’s represent values between 0 and 254 and the user should enter their own IP
address in this form.
a) set eth0 ip xxx.xxx.xxx.xxx

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
12
If using the Menu-driven interface. Select the System Information from the Main
Menu and following screen will appear. Use TAB key to move the cursor and <Enter>
to change the value. Once change the value, select <SAVE> to apply the changes.
After entering the new IP address the system will confirm whether the operation is
successful.
NOTE:
Copy the new address down on a piece of paper. You will need the address when you
are going to use Telnet or set up data transfer/communication connection.
Warning
IP addresses are unique! If an address isn’t available, please contact the
appropriate authorities to apply for one.
5.2 Telnet Access
The Device Server / Managed Media Converter is accessible via a Telnet. At the
command prompt type telnet 192.168.0.254 (If connecting with default IP). You will be
prompted to enter the user name and password as mentioned and shown in the topic
Console Port Access. Use the CLI or the Menu-driven interface to perform the changes.
NOTE:
The only limitation of Telnet Access is that users can not assign a new IP address to
the device server / managed media converter. Please use Console Port Access or
Web Access to assign a new IP address to the unit.

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
13
5.3 Web Access
The Device Server / Managed Media Converter is accessible via a web browser once
connected to the network. Type the IP address at web browser 192.168.0.254 (if
connecting with default IP). A window will prompt you to enter the user name and
password.
(Note: IP 192.168.0.200 has been used for the purpose of writing this manual)
After a successful login, the main screen will appear.

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
14
6 Configuration Management
Users can manage the Device Server via the menu-driven interface or command line
interface from a Telnet or serial console, or via the Web-based graphical user interface.
6.1 Menu-driven User Interface
The figure below shows the Main Menu screen. From this screen the configuration
options available provide the user the ability to quickly access and adjust the device
server settings as required.
Main Menu Screen
Use the TAB key to move the cursor to different fields and press Enter to select/edit
the option.
6.1.1 System Information Menu
From this menu, the user can view system-related information and the default IP
address. The user should set up an appropriate IP address, subnet mask and Gateway
for his/her own network. After entering a new IP address, Telnet and data
communication will be based on the new address.

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
15
System Information menu
Once changes are made, move the cursor to <SAVE> by using the TAB key and press
Enter to save the settings. Changing the IP address will automatically restart the
Device Server / Managed Media Converter.
NOTE:
In Telnet mode you can’t change the IP address.
6.1.2 DHCP Configuration Menu
DHCP (Dynamic Host Configuration Protocol) allows the Device Server / Managed
Media Converter to obtain an IP address from the DHCP server automatically.
NOTE:
A DHCP server must exist and be available in your local network prior to enabling the
DHCP client.

Signamax 065-1063FSx series RS-232/422/485 to 100Base/FX Device Server / Media Converter
16
DHCP Configuration menu
Use the Spacebar to enable/disable the DHCP Client settings. Select <SAVE> to
apply the settings and <ESC> to move to the previous menu. If you don’t want to save
the changes made, just select <ESC> and you will move to the previous menu without
making any changes.
6.1.3 Operation Mode Menu
This page offers the option for the communication model and operation mechanism of
Device Server. Please select the appropriate mode as required for your application.
The user can also monitor the serial port status and configure TCP port numbers from
this menu.
The unit offers six modes (TCP Server / TCP Client / Converter Mode / UDP
Server / UDP Client / Device Server). Please restart the unit after selecting the
desired mode.
Note: If you are using this device in Converter Mode, we recommend you keep the
Packet Mode option set at Disable.
A detailed explanation of the setting choices are given underneath the following
screenshot:
EXPLANATION: Server/Client Mode Configuration
Operation Mode TCP Server: the TCP Server mode of the Device Server allows
TCP connections from up to four Device Servers with TCP Client
mode or PC with Serial IP Redirector program running.